Polyaniline/poly(methyl methacrylate) coaxial fibers: The fabrication and effects of the solution properties on the morphology of electrospun core fibers

Electrically conductive polyaniline (PANi)/poly(methyl methacrylate) (PMMA) coaxial fibers were prepared through the chemical deposition of PANi onto preformed PMMA fibers via in situ polymerization. PMMA fibers were prepared as core materials via electrospinning. Spectral studies and scanning electron microscopy observations indicated the formation of PANi/PMMA coaxial fibers with a diameter of approximately 290 nm and a PANi layer thickness of approximately 30 nm. The conductivity of the PANi/PMMA coaxial fibers was significantly higher than that of electrospun fibers of PANi/poly(ethylene oxide) blends and blend cast films of the same PANi composition. To reproducibly generate uniform‐core polymer fibers, the organic solution properties that affected the morphology and diameter of the electrospun fibers were investigated. The polymer molecular weight, solution concentration, solvent dielectric constant, and addition of soluble organic salts were strongly correlated to the morphology of the electrospun fiber mat. In particular, the dielectric constants of the solvents substantially influenced both the fiber diameter and bead formation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3934–3942, 2004     

Hydrogen ion-selective poly(vinyl chloride) membrane electrode based on a p-tert-butylcalix[4]arene-oxacrown-4

A hydrogen ion-selective poly(vinyl chloride) (PVC) membrane electrode was developed using p-tert-butylcalix[4]arene-oxacrown-4 as ionophore. Apart from the ionophore, plasticisers and lipophilic anions were blended, in various proportions, with PVC in tetrahydrofurane and mixtures so prepared were poured onto glass surfaces to form the membrane. 2-Nitrophenylpentylether has proved to be the best alternative as plasticiser and the lipophilic anions tried have turned out to have an adverse effect on the pH response. The electrode of the optimum characteristics had a composition of 2% p-tert-butylcalix[4]arene-oxacrown-4, 68.3% o-NPPE and 29.7% PVC. The electrode showed an apparent Nernstian response in the pH range 2-11 with a slope of 54.2±0.4 mV pH⁻¹ at 20±1 °C. It has a rapid potential-response to changes of pH, high ion selectivity towards lithium, sodium and potassium, and other characteristics comparable to those reported for the conventional pH glass membrane electrode. It appears to be a suitable potentiometric indicator electrode specifically for hydrofluoric acid solutions.     

Carrier-mediated blends of Chitosan with polyvinyl chloride for different applications

The current work aims at blending of PVC with Chitosan through simultaneous casting of their separate solutions in different proportions of PVC and Chitosan in suitable solvents. After dissolution, both solutions were added to each other while stirring at room temperature. The obtained mixture was left at room temperature to form the blend after evaporation of the solvent. Similar blends have been prepared similarly in presence of the organic ligand, dithizone, as a carrier-mediating material for different metal ions. PVC/Chitosan blends were characterized by thermal (TGA) and FT-IR Spectroscopic analyses as well as scanning electron microscopy (SEM). The obtained blends were found to have reasonable extent of compatibility between their components. Such compatibility depends mainly on the way with which the components have been blended with each other. The polymer-supported dithizone was investigated toward its ability to be used for removal of some metal ions from their aqueous solutions. Concentration of metal ions was determined by ICP-AES analysis.     

以多层次聚苯胺颗粒为电极活性物质的超级电容器的电化学性能

以(NH₄)₂S₂O₈为氧化剂用化学氧化法合成了具有多层次结构的聚苯胺颗粒，其二次颗粒由一次颗粒集结而成，一次颗粒的粒径基本上在1 μm以下，一次颗粒由多层微小薄片叠合而成. 用这种聚苯胺为活性物质制成电极，以2 mol•L^-1的H₂SO₄水溶液作电解液，组装成了聚苯胺电极超级电容器. 用循环伏安法、电化学阻抗谱和恒电流充放电技术测试了该超级电容器的电化学性能.在7 mA的充放电电流下，它的比能量可达6.35 Wh•kg^-1，比功率可达132 W•kg^-1，电极材料的比容量可达408 F•g^-1. 在20 mA的充放电电流下，它的比能量可达4.39 Wh•kg^-1，比功率可达328 W•kg^-1，电极材料的比容量可达324 F•g^-1. 在100次的充放电循环中，聚苯胺电极超级电容器的电容量没有下降，电荷充放电效率一直保持在95%左右.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

PDMS migration at poly(vinyl chloride)/poly(ɛ-caprolactone)/poly(ɛ-caprolactone)-b-poly(dimethylsiloxane) blends surfaces

Films composed of poly(vinyl chloride)/poly(?-caprolactone)/poly(?-caprolactone)-b-poly(dimethylsiloxane) [PVC/PCL/(PCL-b-PDMS)] blends were prepared by solvent casting from tetrahydrofuran. The PVC content was kept constant (60 wt %) while varying the PCL and PCL-b-PDMS contents, part of the PCL (0–20 wt %) in the PVC/PCL (60/40) blend being replaced with PCL-b-PDMS with different molecular weights of the PCL blocks. The prepared blends were investigated by infrared spectroscopy and contact angle measurements. FTIR analysis and contact angle measurements indicate that the PDMS blocks tend to migrate towards the surface and this migration is preferential to the side in contact with air.     

Poly(?-caprolactone)-based ‘green’ plasticizers for poly(vinyl choride)

A series of proposed plasticizers for poly(vinyl chloride) (PVC), based on poly(?-caprolactone) (PCL) with octanoate and benzoate-terminal groups, were synthesized with various microstructures and molecular weights (MW) and tested for biodegradability as well as for mechanical performance, and leaching resistance in blends with PVC. The plasticization efficiency of each was characterized by measuring the glass transition temperature (T_g) and tensile properties of PCL/PVC blends. The PCL-octanoate plasticizers demonstrated plasticization efficiency similar to di(ethylhexyl) phthalate (DEHP) with the same plasticizer loading. PCL-benzoate/PVC blends had much higher T_gs (∼20 °C higher) compared to PCL-octanoate/PVC and DEHP/PVC blends. Yield stresses were about two times higher for PCL-benzoate/PVC blends compared to PCL-octanoate/PVC and DEHP/PVC blends, reflecting the stiffer nature of such blends. Biodegradation was rapid for all PCL-octanoates, with the exception of linear PCL-octanoates with arm molecular weights >10³ g mol⁻¹. Biodegradation rates of PCLs by Rhodococcus rhodocrous were not affected by microstructure for the range of PCL topologies studied (linear versus three or four arms) but were slower for PCLs made from commercial PCL-diols that had a central ether linkage due to the initiator used to make these compounds. Leaching resistance was higher as PCL molecular weight increased and, for pairs of comparable sized species, significantly less PCL-benzoate leached out compared to the PCL-octanoate. For the range of PCL topologies studied, the number of arms did not significantly affect leaching resistance. In summary, both the end group and the molecular weight influenced the leaching resistance of the PCL. PCL-octanoates were comparable plasticizers to DEHP in terms of the mechanical properties examined, and were rapidly degraded by a common soil microorganism.     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.     

Radiation-induced conductivity control in polyaniline blends/composites

Polyaniline (PANI) blends with chlorine-containing polymers and copolymers and composites with HCl-releasing compounds were prepared to investigate their radiation response in terms of induced conductivities. Blends of non-conductive PANI with poly(vinyl chloride) (PVC), poly(vinylidene chloride-co-vinyl acetate), [P(VDC-co-VAc)], poly(vinylidene chloride-co-vinyl chloride), [P(VDC-co-VC)] were prepared in the form of as-cast films. A number of blends which are different in composition were exposed to gamma radiation and accelerated electrons to various doses, and the effects of irradiation type and composition of polymers on the conductivity of films were investigated by using conductivity measurements and UV–vis and FT-IR spectroscopy. The results clearly showed that ionizing radiation is an effective tool to induce and control conductivity in the blends of PANI-base with chlorine-carrying polymers as well as its composites prepared from HCl-releasing compounds such as chloral hydrate. The main mechanism behind this radiation-induced conductivity is in situ doping of PANI-base with HCl released from partner polymers and low molecular weight compounds by the effect of radiation.     

Preparation and characterization of polyaniline blends with polyvinyl acetate,polystyrene and polyvinyl chloride for toxic gas sensors

The conditions of processing and gas sensing of ­polyaniline (PANi) blends with polyvinyl acetate (PVAc), polystyrene (PS) and polyvinyl chloride (PVC) were investigated. Flexible, free‐standing and stretchable films of various blends compositions were obtained by casting. The mechanisms of the conducting blends response to a selection of gases and vapours were investigated using two techniques: measurement of conductance and mass changes using a four‐point probe method and X‐ray fluorescence (XRF) device, respectively. These responses to toxic gases and vapours are better explained by polymer blends than homopolymers. Prepared films were exposed to hydrogen halides, hydrogen cyanide, halogens, monochloroacetic acid (MCAA), 1‐3‐5 trichloromethyl benzene (TCMB), methylbenzyl bromide (MBB), bromoacetone (BA) and cyanogen bromide (CB). The changes in conductivity of various polymer frequently observed are partly due to one stage in the two‐stage sorption perhaps involving the swelling of the polymer and then diffusion of gases into polymer chains. The swelling of polymers is a slow process, therefore, we have pre‐swelled polymer films which tend to decrease the response times of blends in respect to gases. The structures of the blends are examined by STA (TGA & DSC) and SEM studies. Copyright © 2001 John Wiley & Sons, Ltd.     

Study of the properties of rigid and plasticized PVC/PMMA blends

The aim of this work is to study the structure-properties relationship of rigid and plasticized PVC/PMMA blends. For that purpose, blends of variable compositions were prepared in the absence and in the presence of a plasticizer di (ethyl-2 hexyl) phtalate or DEHP. The miscibility of the two polymers was investigated by differential scanning calorimetric analysis (DSC) and Fourier transform infrared spectroscopy. The weight loss from 30 to 600°C was investigated by thermogravimetric analysis (TGA). The thermal degradation under nitrogen at 185°C was studied and the amount of HCl released from PVC was measured by the pH method. Furthermore, the variation of mechanical properties such as tensile behavior, hardness and impact resistance was investigated for all blend compositions.     

SAN共聚物组成对PVC/ABS共混物相容性的影响

采用乳液聚合技术通过改变共聚单体的投料比(St/AN)合成了一系列不同AN结合量的ABS接枝共聚物粉料和SAN共聚物.将其与聚氯乙烯(PVC)和邻苯二甲酸二辛酯(DOP)熔融共混分别制得了PVC/ABS、PVC/SAN、PVC/ABS/DOP和PVC/SAN/DOP共混物,利用SEM、TEM和动态力学粘弹谱仪(DMA)对共混物的相容性和相结构进行了表征.结果发现,在PVC/ABS共混体系中,尽管改变接枝SAN共聚物的AN结合量,PVC和SAN共聚物均为不相容体系;在该共混物中引入增塑剂DOP后,虽然当SAN共聚物AN结合量小于23.4 wt%时,共混物在室温以上只存在一个tanδ峰,但形态结构研究结果表明共混物仍为不相容体系,共混物的相区尺寸明显地依赖于SAN共聚物中的AN结合量,当AN结合量为23.4 wt%时相区尺寸最小.     

Effects of gamma irradiation on poly(vinyl chloride)/polystyrene blends: Investigation of radiolytic stabilization and miscibility of the mixture

Commercial polystyrene (PS) has been studied as a modifier for commercial poly(vinyl chloride) (PVC) when it was submitted to gamma irradiation. PVC/PS blends were prepared with 100/0, 95/05 and 90/10 compositions. Results for gamma-irradiated (⁶⁰Co) blends are reported and changes in viscosity-average molar mass (M_v) were analyzed. The study showed that the addition of PS into PVC decreased by 73% (95/05) and 79% (90/10) the number of scissions/100 eV in the dose range of 25-100 kGy. Viscosity analyses by the Pan et al. criterion and analyses of FT-IR spectra in the C-Cl vibration region showed negligible intermolecular interactions between the components of PVC/PS blends. However when the films of blends were irradiated to 50 kGy, certain intermolecular interactions were observed by the viscosity method. The addition of PS to PVC and the main scission effect induced by gamma irradiation decreased crosslink density of blends causing changes in the elongation of break and Young's modulus.     

The influence of core-shell structured modifiers on the toughness of poly (vinyl chloride)

The core-shell structured grafted copolymer particles of polybutadiene grafted polymethyl methacrylate (PB-g-PMMA, MB) were prepared by emulsion polymerization. The MB particles were used to modify poly (vinyl chloride) (PVC) by melt blending. The mechanical properties of the PVC blends were investigated. The micro-morphology of the PVC blends was observed by scanning electron microscopy (SEM). The results indicated that the samples with the best impact strength could be obtained when the core-shell weight ratio of PB to PMMA is lower than 93:7, the mechanical properties correlated well with SEM morphologies, the addition of modifier with the ratio core to shell of 93:7 could reduce the domain size of the dispersed phase. Furthermore, the compatibility and properties of the blends were greatly enhanced and improved. The modifier particles could be well dispersed in the PVC matrix.     

Miscibility of semirigid thermotropic liquid crystalline polycarbonate with poly(vinyl chloride)

Miscibility and morphology of polymer blends of semirigid thermotropic liquid crystalline (LC) polycarbonate (LCPC) with three commercial amorphous poly(vinyl chloride)s (PVC) having various molecular weights were investigated by means of differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). No phase separation was observed in the LCPC/PVC polymer blends. LCPC forms miscible polymer blends with the PVCs independent of molecular weight. The dynamic storage modulus of the LCPC/PVC polymer blends changes systematically with blend composition.     

Preparation and characterization of wet poly(vinyl chloride)-polypyrolle composite film

Wet poly(vinyl chloride) (wPVC) coated glassy carbon (GC) electrode was prepared by casting a DMF solution of poly(vinyl chloride) on glassy carbon and immersing it in methanol, and then in water. The wPVC coated GC (wPVC/GC) electrode showed electrochemical activity in aqueous solution; therefore, it was possible to obtain a wPVC/polypyrolle (PPy) composite by electropolymerization from aqueous solution of pyrolle (Py) into the wPVC matrix on the electrode. PPy segregated in wPVC matrix and the mechanical properties of PPy was improved by forming a composite without changing the electrochemical properties of PPy. The PPy/wPVC ratio can be controlled by controlling the concentration of PVC in DMF solution.     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

石墨烯-壳聚糖修饰玻碳电极应用于环境水中五氯酚的测定

制备了石墨烯(CRG)-壳聚糖(CS)修饰玻碳(CRG-CS/GC)电极,用循环伏安法和示差脉冲伏安法研究了五氯酚(PCP)的电化学行为,发现其氧化电流信号与GC电极相比明显增强,表明修饰电极对PCP具有较强的吸附作用,并能够加速电子传递。 建立了一种灵敏简便、重现性好、稳定性好的测定PCP的新修饰电极方法,线性响应范围为1.00×10-7~1.00×10-5 mol/L（R=0.9975）,检测限为2.3×10-8 mol/L(S/N=3)。 将该修饰电极应用于实际水样分析,回收率为97%~103%。     

Morphology and fracture behavior of toughening‐modified poly(vinyl chloride)/organophilic montmorillonite composites

Toughening‐modified poly(vinyl chloride) (PVC)/organophilic montmorillonite (OMMT) composites with an impact‐modifier resin (Blendex 338) were prepared by melt intercalation, and their microstructures were investigated with wide‐angle X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy. The mechanical properties of the PVC composites were examined in terms of the content of Blendex and OMMT, and the fracture toughness was analyzed with a modified essential work of fracture model. Intercalated structures were found in the PVC/OMMT composites with or without Blendex. Either Blendex or OMMT could improve the elongation at break and notched impact strength of PVC at proper contents. With the addition of 30 phr or more of Blendex, supertough behavior was observed for PVC/Blendex blends, and their notched impact strength was increased more than 3319% compared with that of pristine PVC. Furthermore, the addition of OMMT greatly improved both the toughness and strength of PVC/Blendex blends, and the toughening effect of OMMT on PVC/Blendex blends was much larger than that on pristine PVC. Blendex and OMMT synergistically improved the mechanical properties of PVC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 286–295, 2004     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.