Graft copolymerization of methacrylic acid onto carboxymethyl chitosan

Carboxymethyl chitosan (CMCTS) was prepared and characterized by FTIR, ¹H NMR, and elemental analysis. The graft copolymerization of methacrylic acid (MAA) onto CMCTS using ammonium persulfate (APS) as an initiator was carried out in an aqueous solution. Evidence of grafting was obtained by comparison of FTIR spectra of CMCTS and the grafted copolymer as well as solubility characteristics of the products. The effects of APS, MAA, reaction temperature and time on graft copolymerization were studied by determining the grafting parameters such as grafting percentage and grafting efficiency. With keeping other conditions constant, the optimum conditions were shown as following: [APS]=8 mmol/l, [MAA]=2.4 mol/l, reaction temperature=60-70 °C, reaction time=120 min.     

Graft copolymerisation of acrylamide onto cashew gum

The synthesis of cashew gum-g-polyacrylamide was carried out at 60 °C by a radical polymerisation using potassium persulphate as the redox initiator under N₂ atmosphere. A series of graft copolymers, varying in acrylamide concentration and keeping the concentration of the initiator and polysaccharide constant, was prepared. These graft copolymers were characterised by elemental analysis, infrared and ¹³C NMR spectroscopy, rheological studies, differential scanning calorimetry and thermogravimetric analysis. Comparisons amongst grafting parameters of the reaction of various natural polysaccharides with polyacrylamide (PAM) were carried out. High percentages of acrylamide conversion (%C) and grafting efficiency (%E) were obtained for cashew gum (CG), even with a low acrylamide/gum ratio. All copolymers had intrinsic viscosity and thus the hydrodynamic volume much higher than the CG value and closer to the PAM. The CG-g-PAM solution had an absolute viscosity at 2.5% concentration (wt./vol.) up to 33 and 3.3 times the CG and PAM values, respectively. Grafting of PAM chains onto the polysaccharide enhances its thermal stability.     

丙烯酰胺在炭黑表面接枝聚合研究

利用Ｃｅ＾４＋和羟甲基化炭黑组成的氧化还原引发体系，探讨了丙烯酰胺在炭黑表面的自由基水溶液接枝聚合机理。研究表明：单体浓度、硝酸浓度和铈盐用量直接影响丙烯酰胺在炭黑表面的接枝聚合，ＦＴＩ和ＴＥＭ分析证明：改性炭黑表面存在着聚丙烯酰胺。改性炭黑粒子的Ｚｅｔａ电位值与未改性炭黑粒子相同，但它与水组成的分散体具有极好的分散稳定性。     

Graft copolymerization of methyl acrylate onto potato starch initiated by ceric ammonium nitrate

A study was made of the ceric ammonium nitrate (CAN) initiated graft copolymerization of methyl acrylate (MA) onto potato starch. The variables affecting the graft were investigated. The optimums have been obtained; they are the concentrations of MA, CAN, and nitric acid (HNO₃) (1.08, 5.0 × 10^?3, and 0.081 mol/L, respectively). The reaction temperature is ca. 50°C and the reaction time is 2 h. The molecular weight of grafted poly(methylacrylate) has been determined. On the basis of experimental results, the mechanism of grafting has been explored, a new kinetic equation of the graft copolymerization is established: R_p = Kk_d [STOH] [Ce⁴⁺] + Kk_pk_d/k_t[STOH][M], where K, k_d, k_p, and k_t are constants. The equation fits the results of experiments. © 1993 John Wiley & Sons, Inc.     

Graft copolymerization of acrylamide onto casein: A kinetic study

Polyacrylamide has been grafted onto casein in phosphate buffer medium using potassium peroxodisulfate as initiator. The influence of synthetic variables on percent grafting, grafting efficiency, rates of conversion of monomer, and the rates of graft copolymerization have been discussed. A possible kinetic scheme based on experimental results has been derived.     

Gamma radiation induced graft copolymerization of acrylamide onto EPDM blended with PE

Gamma radiation induced grafting of acrylamide (AAm) onto vulcanized strips of EPDM and EPDM/PE blends has been carried out. The effects of different parameters on the graft yield have been investigated. These parameters include: radiation dose, monomer concentration, diluent composition and types of inhibitors. It has been found that water is the most appropriate solvent. The preswelling of crosslinked rubber samples in cyclohexane prior to grafting enhances the grafting and the addition of methanol to water as binary diluent in the ratio (1 : 1) decreases the graft yield. The presence of Mohr's salt and copper sulfate in the reaction mixture in the molar ratio (2.1 : 0.5) markedly increases the graft yield. Evidence of grafting have been conducted using thermal analysis as well as swelling measurements in water. Also, it has been found that the mechanical properties of the blends decrease at graft yield 13%. Copyright © 2002 John Wiley & Sons, Ltd.     

过硫酸铵-亚硫酸氢钠引发活化淀粉与丙烯酰胺反相乳液聚合动力学研究

以过硫酸铵-亚硫酸氢钠作为氧化还原引发剂,研究了经球磨活化的淀粉与丙烯酰胺在反相乳液体系中的接枝共聚反应动力学,分别考察了反应温度、引发剂浓度、淀粉浓度、单体浓度、乳化剂用量对接枝速率的影响.结果表明,在实验考察范围内的动力学关系式为:Rp∝[(NH4)2S2O4)]0.571[NaHSO3]0.571[St]0.59...     

Emulsifier-free emulsion copolymerization of styrene and acrylamide using an amphoteric initiator

Emulsifier-free emulsion copolymerization of styrene (St) and acrylamide (AAm) has been investigated in the presence of an amphoteric water-soluble initiator, 2,2′-azobis[N-(2-carboxyethyl)-2-2-methylpropionamidine]hydrate (VA057). The kinetics of polymerization and the colloidal properties of the resulting latices were studied and compared with the cases using ionic initiators. When adopting the amphoteric initiator at pHs lower than 10, stable amphoteric poly (St/AAm) latices, evidenced by the electrophoretic mobility, were prepared directly. Meanwhile, almost the same conversion versus time curves appeared and there were no apparent differences in the final particle sizes for those polymerizations, whereas in the polymerization at pH 10, a much lower rate of copolymerization and a larger size of particles were observed. The surface charge density and the growth rate of latex particles produced with VA057 at pH<10 were comparable to those of the particles with a cationic initiator, 2,2′-azobis(2-amidinopropane)dihydrochloride, but were apparently lower than those with an anionic initiator, potassium persulfate, when the polymerizations were carried out under corresponding conditions. The number of initiator fragments incorporated onto the particle surfaces was independent of polymerization pH, except for pH 10. The abnormal performance of VA057 at pH 10 was attributed to its degradation due to hydrolysis. Received: 14 December 1999 Accepted: 22 February 2000     

Graft polymerization of vinyl monomers onto nanosized alumina particles

To enhance the interfacial interaction in alumina nanoparticles filled polymer composites, an effective surface modification method was developed by grafting polystyrene and polyacrylamide onto the particles. That is, the alumina surface was firstly treated with silane, followed by radical grafting polymerization in aqueous or non-aqueous systems. Results of infrared spectroscopy and dispersiveness in solvents demonstrated that the desired polymer chains have been covalently bonded to the surface of the alumina particles. They also greatly changed their surface characteristics. In addition, effects of polymerization conditions, including ways of monomer feeding, concentrations of monomer and initiator, and reaction time, on the grafting reaction were presented. It was found that the growing polymer radicals and/or the grafted polymer chains had a blocking effect on the diffusion of radicals or monomers towards the surface of nanoalumina. This was due to the fact that the interaction between the solvent and the grafted polymers was weaker than that between the grafted polymers and the nanoparticles.     

Graft copolymerization of methacrylic acid and acrylamide onto acrylonitrile-butadiene-styrene terpolymer by photoinduced hydroperoxide

Graft copolymerization of methacrylic acid (MAA) or acrylamide (AM) from an aqueous solution onto acrylonitrile-butadiene-styrene terpolymer (ABS) was initiated by the thermal decomposition of polymeric hydroperoxides, which are formed upon UV irradiationof ABS, which contains anthracene. Diffusion of anthracene at room temperature from a methanolic solution into ABS was affected by the acrylonitrile content ofABS.The graft yield was independent on the concentration of anthracene in the wide range of 0.03 X 10^-3 to 14.29 X 10^?3 mol/L in ABS. The graft polymerization reaction does not occur below 100°C.The effect of other variables, such as time of irradiation, intensity of UV, reaction time, and concentration of monomer in aqueous solution, on the amount of monomer grafted to ABS were also investigated.The contact angle significantly decreases upon grafting, indicating that the graft layer is on the surface of the polymer. © 1995 John Wiley & Sons, Inc.     

Graft copolymerization of itaconic acid-methacrylamide comonomers onto poly(ethylene terephthalate) fibers

The graft copolymerization of itaconic acid-methacrylamide (IA-MAAm) comonomers was carried out using benzoyl peroxide as initiator onto poly(ethylene terephthalate) (PET) fibers in an aqueous medium. The grafted fibers were characterized by FTIR, TGA, DSC and SEM analysis. Effect of various parameters on graft yield such as feed composition, feed and initiator concentration, reaction time and temperature were investigated. The graft yield in the presence of MAAm increased because of the synergistic effect of MAAm comonomer. While, the graft yield alone with the IA onto PET fiber was 2.2%, the use of MAAm as a comonomer increased the amount of IA introduced to the PET fiber up to 13.7%. The reactivity ratios for both monomers were determined by using a Fineman-Ross plot. The grafting rate and saturation graft yield was increased upon increasing the temperature between 65 °C and 85 °C. When the temperature increased further than 85 °C, the saturation graft yield decreased. The graft yield has shown an increase up to an initiator concentration of 1.0 × 10⁻² M and slightly decreased. The grafting increased the dyeability with acidic and basic dyes, and moisture absorption capacity but decreased the thermal stability of the fibers.     

Graft copolymerization of acrylonitrile onto polystyrene

It is possible to graft vinyl monomers, such as acrylonitrile, onto polystyrene via anionic processes but not by a radical process. Both homopolymerization of the added acrylonitrile and graft copolymerization in which acrylonitrile units are added to the para position on the benzene ring in styrene occur; the conversion of acrylonitrile into polymer depends upon the time and temperature of the reaction and on the concentration of the anionic initiator, butyllithium. A constant 15–20% of the acrylonitrile is converted to graft copolymer while the remainder is homopolymerized; graft copolymer may be separated from homopolymer by selective precipitation from either N,N′-dimethylformamide or aqueous potassium thiocyanate. Treatment of the mixed graft and homopolymer with aqueous sodium hydroxide converts the nitrile into an acid salt and one may conveniently separate homopolymer from graft copolymer in this way. Each polystyrene chain is grafted with acrylonitrile units. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1275–1282, 1997     

Nitroxide-mediated radical polymerization of acrylamide in water solution

This study shows that reasonably controlled nitroxide-mediated polymerization of acrylamide is achieved in pure water solution at 120 °C and high concentration (40 wt%), using a combination of a conventional hydrosoluble radical initiator (Vazo56) and a β-phosphonylated nitroxide, SG1. Moreover, some chain extensions can be performed from a polyacrylamide macroinitiator. Under these experimental conditions, we have demonstrated the conservation of the acrylamide structure without hydrolysis side reactions. The physico-chemical characterizations of polymers obtained from this method demonstrates that the controlled growing chain arises as a star-like shape from the hydrophobic core composed of SG1-functionalized polyacrylamide in the presence of a slight excess of SG1.     

Graft copolymerization of methyl methacrylate onto curdlan

Graft copolymerization of methyl methacrylate onto curdlan was first investigated. In the graft copolymerization initiated by ammonium persulfate (APS) in DMSO under a homogeneous condition, the resulting graft copolymers had low molecular weights and low grafting percentages. However, the initiation by APS in water gave graft copolymers having relatively higher molecular weight ( ) and higher grafting percentage (548%) than those copolymers obtained by the homogeneous condition. When the graft copolymerization was carried out by cerium (IV) ammonium nitrate-HNO₃ initiation, the graft copolymer had the highest grafting percentage of 1620% without degradation of the curdlan backbone. The resulting graft copolymers were soluble in DMSO. The graft copolymers obtained by the cerium salt had narrow molecular weight distributions () compared with those by the APS catalyst in DMSO or water. The graft copolymers decomposed with sulfuric acid to isolate PMMAs, which molecular weights were larger than that of the corresponding homo-PMMAs. The structure of the grafted copolymers was characterized by IR, ¹³C NMR, DSC, and SEM. It was found that the graft copolymers exhibited the glass transition temperature (T_g), though curdlan had no T_g. As the grafting percentage increased, the T_g increased to reach 270°C, which was higher than the decomposition temperature of curdlan. The surface image of the grafted copolymers observed by SEM, showed smoothless compared with that of curdlan. It was also revealed that the graft copolymers having the grafting percentage of 1620% swelled in common organic solvents up to 4.5 times of the weight of the dry graft copolymer to form gels. © 1996 John Wiley & Sons, Inc.     

CAN引发S-DMDAAC-AM接枝共聚的研究

以硝酸铈铵(CAN)为引发剂,以淀粉(S)、二甲基二烯丙基氯化铵(DMDAAC)和丙烯酰胺(AM)为原料,通过反相乳液聚合,合成接枝共聚物。研究了加料顺序、引发剂浓度、单体与淀粉配比、油水体积比、乳化剂用量等因素对产品性能的影响。并用IR和1H-NMR对接枝产物进行了分析表征。     

Graft copolymerization onto rubber. V. Graft copolymerization of methyl methacrylate onto rubber using potassium peroxydiphosphate as initiator

The graft copolymerization of methyl methacrylate onto natural rubber (NR) is investigated using potassium peroxydiphosphate as the initiator. The rate of grafting is determined by varying monomer concentration, peroxydiphosphate concentration, and temperature. The graft yield increased with an increase in monomer concentration up to 1.4082M/L and thereafter the graft yield decreases. The graft yield increases significantly with an increase of peroxydiphosphate concentration up to 150 X 10^-1M/L and thereafter the graft yield decreases. The grafting reaction is temperature dependent. A suitable kinetic scheme is proposed and the rate equation is evaluated.     

Graft polymerization of vinyl monomers onto cotton fibres pretreated with amines

The influence of treating cotton fibres with several amines on the mechanical properties, moisture sorption ability before and after graft polymerization, and on graft yields for various water-soluble and water-insoluble vinyl monomers were analysed. As compared to water, the treatment with amines, ethylenediamine (EDA) in particular, resulted in a decrease in the crystallinity and tensile strength of the cotton fibres, and an increase in the moisture sorption. The graft yields of amine-treated cotton fibres using water-soluble monomers, acrylic acid (AA), methacrylic acid (MAA) and acrylamide (AM) were greater than those observed for water-treated cotton fibres, whereas the graft yields using water-insoluble monomers, methyl acrylate (MA), methyl methacrylate (MMA) and vinyl acetate (VA) were lower. The moisture sorption ability was improved by the graft polymerization with water-soluble monomers. The improvement was enhanced for MA and MAA by treatment with sodium hydroxide to form the corresponding sodium carboxylate derivatives. The tensile strength of EDA-treated cotton was slightly reduced by grafting, while that of the water-activated cotton yarn was barely changed. These results suggest that the graft polymerization of amine-treated cotton fibres with certain vinyl monomers increased the moisture sorption ability without resulting in increased fibre rigidity.     

Graft modification of starch nanoparticles with pH-responsive polymers via nitroxide-mediated polymerization

The grafting to approach and nitroxide-mediated polymerization (NMP) were used to graft modify starch nanoparticles (SNP) with pH-responsive polymers. SG1-capped poly(2-(dimethylamino)ethyl methacrylate-co-styrene), P(DMAEMA-co-S), and poly(2-(diethylamino)ethyl methacrylate-co-styrene), P(DEAEMA-co-S), with relatively low dispersity and high degree of livingness was synthesized in bulk via NMP using a commercial available alkoxyamine. These macroalkoxyamines were then grafted to vinyl benzyl-functionalized SNP (SNP-VBC) to obtain pH-responsive materials. The grafted SNP were characterized by proton nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and elemental analysis confirming the successful synthesis of these new materials. Low grafting efficiencies (~6%) were observed for both SNP-grafted materials with pH-responsive polymers, as expected when using the grafting to approach. The pH-responsiveness of SNP-g-P(DMAEMA-co-S) and SNP-g-P(DEAEMA-co-S) was confirmed by measuring the ζ-potential at different pH values. At acidic conditions (pH 3–6) the grafted materials were protonated and exhibited positive ζ-potential, whereas at basic conditions (pH 10–13) the same grafted materials were deprotonated and exhibited negative ζ-potential.