Structural investigation of poly (methyl acrylate) by 2D HMBC NMR

Three and four bond order couplings between carbonyl carbon and other neighboring protons have been investigated in detail with the help of 2D heteronuclear multiple bond correlation (HMBC) spectrum. The methine and methylene protons in pentad and tetrad configuration were found to couple with carbonyl carbon. The intensity ratio of methylene protons’ cross peaks in HMBC spectrum shows that 50% of poly methyl acrylate (PMA) is in isotactic and 50% is in syndiotactic configuration. The configurational analysis was mainly carried out with the help of 2D HMBC spectrum.     

Thermosensitive poly(methyl methacrylate) emulsion prepared in the presence of poly(vinyl alcohol) with a cloud point as a protective colloid

An emulsion of poly(methyl methacrylate) (PMMA) was prepared using poly(vinyl alcohol) (PVA) of low degree of hydrolysis with a cloud point as a protective colloid. The behaviour of an aqueous solution of PVA with 80% degree of hydrolysis was first investigated in terms of the Huggins constant in viscometry. MMA was polymerized using the PVA at 20 °C, where no abnormality in the aqueous PVA was observed. The change in transmittance of the emulsion observed with a UV–vis photometer revealed that in the case of UV light of wavelength 370 nm, the transmittance decreased markedly at around 30 °C with an increase in temperature, and then increased with a decrease in temperature. The thermosensitive property resulted from PVA with a low degree of hydrolysis with a cloud point, at a higher temperature of which the PVA loses solubility in water owing to weakening of the hydrogen bond between PVA molecules and water.     

Characteristic ratio of poly(tetrahydrofurfuryl acrylate) and poly(2-ethylbutyl acrylate)

The synthesis, characteristic ratio C_∞ and glass transition temperature (T_g) of poly(tetrahydrofurfuryl acrylate) (PTHFA) and of poly(2-ethylbutyl acrylate) (P2EBA) are reported. P2EBA has slightly lower flexibility (C_∞ = 9.2) than PTHFA (C_∞ = 8.6), mainly because of the higher bulkiness of its side group and the closer proximity to the main chain. The C_∞ results compared with the corresponding polymethacrylates show an increase in flexibility due to the absence of the α-methyl group. Comparison with poly(methyl acrylate) clearly shows the influence of the bulkiness of the side group on the chain flexibility. The lower T_g of P2EBA than that of PTHFA may be explained by the higher flexibility of the 2-ethylbutyl side group. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1589–1592, 1997     

Thermosensitive superabsorbents based on poly(N,N-diethylacrylamide-co-sodium acrylate)

A series of poly(N,N-diethylacrylamide-co-sodium acrylate) with a degree of crosslinking of 1 mol%have been prepared as thermosensitive superabsorbents for water.The critical swelling temperatures or the volume phase transition temperature(VPTT) and the water absorption capacity of the polymers can be modulated by varying the amount of sodium acrylate(0-60 mol%) in the copolymers.The water absorption and swelling properties of the different hydrogels have been studied as function of temperature.The crosslinked copolymers can absorb large amounts of water at ambient temperatures and dehydrate at higher temperatures with relative ease,making the absorbent materials thermally responsive and thus reusable.The water absorption capacity of the copolymers depends on the pH of the media as the acrylate monomer has a higher water absorption in its deprotonated state.Added urea in the media raises and sharpens the VPTT values of the copolymers containing sodium acrylate.     

Synthesis and interfacial properties of a novel inverse demulsifier of nanosized poly[(methyl methacrylate)-co-(ethyl acrylate)-co-(methacrylic acid)-co-(acrylamide)] latex

An acrylic emulsion-type inverse demulsifier (named as PMEMA latex) was prepared by using methyl methacrylate (MMA), ethyl acrylate (EA), methacrylic acid (MAA), and acrylamide (AM) as monomers. The effects of reaction conditions toward the copolymerization results were investigated by evaluating various evaluation parameters, including conversion, molecular weight, and diameter. In addition, the interfacial properties of PMEMA latex were investigated to study its demulsification mechanism about treating the O/W emulsion.     

Nanodomains in a hydrophilic-hydrophobic IPN based on poly(2-hydroxyethyl acrylate) and poly(ethyl acrylate)

The morphology of a series of hydrogels based on the interpenetration of poly(2-hydroxyethyl acrylate) and poly(ethyl acrylate) has been studied through transmission electron microscopy, TEM, atomic force microscopy, AFM, and dynamic-mechanical spectroscopy, DMA. For the TEM analysis phosphotungstic acid, PTA, was used as alternative selective staining agent to those commonly used. The good agreement between TEM and AFM images allowed us to confirm that the PTA technique is a very powerful tool for TEM analysis of these hydrogel systems. All the results show that the IPNs presented phase-separation with two kinds of microdomains: those preferentially with a hydrophilic nature and those with preferentially a hydrophobic one, of sizes that range from 30 nm to 100 nm. Each one of these domains is composed by smaller nanodomains of alternating hydrophobic and hydrophilic component ranging between 6 and 10 nm sizes, those preferentially with a hydrophilic nature having a larger proportion of hydrophilic nanodomains. The AFM images of the IPN with the highest PHEA mass fraction, x_PHEA = 0.75, suggest that the hydrophilic phase is co-continuous in the material. A disperse hydrophilic phase is found when the PHEA mass fraction is reduced up to x_PHEA = 0.38. This phase-separation is explained in terms of some characteristic parameters of the networks such as the mesh size and the number of units between cross-links. The morphology found makes the systems very attractive for cell adhesion substrates and for matrices of scaffolds in soft tissue engineering.     

Emulsions Stabilized with poly(Hydroxyethyl Acrylate-co-Coumaryl Acrylate-co-2-Ethylhexyl acrylate)

Thermo- and photo-responsive emulsions were prepared using mineral oil as an oil phase and a thermo- and-photo-sensitive polymer as an emulsifier. Hydroxyethyl acrylate (HEA) was copolymerized with Coumaryl acrylate (CA) and 2-Ethylhexyl acrylate (EHA) by a free radical reaction with the content of CA in the reaction mixture being varied (0, 0.5, 1, 2, 3 mol%) and the content of EHA being kept constant (2 mol%). CA was used as a photo-responsive comonomer and EHA was used as a hydrophobic comonomer to endow the copolymer with amphiphilicity. The copolymers prepared using the HEA/CA/EHA mixture where CA content was 1, 2, 3 mol% exhibited a phase transition in the range of 20°C– 45°C, and the phase transition temperature decreased with increasing the content. The CA of the copolymers was readily dimerized under the irradiation of UV (365 nm. 400 W) and the dimerization degree was 27%–47% in 60 min. The droplet size of emulsions significantly increased with increasing the temperature from 27°C- 50°C, possibly due to the thermal contraction of the copolymers. Also, the size markedly increased by 60 min-irradiation of the UV light, possibly because of the photo collapse of the copolymers.     

Synthesis and characterizations of novel, positively charged poly(methyl acrylate)-SiO2 nanocomposites

A series of positively charged poly(methyl acrylate) (PMA)-SiO₂ nanocomposites were prepared through the sol-gel process of positively charged alkoxysilane-containing polymer precursors. The precursors were synthesized by coupling different amounts of N-[3-(Trimethoxysilyl) propyl] ethylene diamine (A-1120) to poly(methyl acrylate) (PMA), followed by a quaternization reaction. These precursors were then hydrolyzed and condensed to generate PMA-SiO₂ hybrid sol-gel materials. IR and ¹H NMR measurements were conducted to confirm the chemical structure of the step products during the hybrids preparation. Thermal stabilities of the hybrids were conducted by DSC, TGA and their nanoscale microphase separation was distinguished by FE-SEM. Anion-exchange capacities of these nanocomposites were examined to be in the range of 0.19−1.20 mmol/g.     

Synthesis of new polyfunctional 2-pyrrolidinones from methyl 2-(carboethoxyhydroxymethyl)acrylate

The synthesis of new polyfunctional 2-pyrrolidinone derivatives from methyl 2-(carboethoxyhydroxymethyl)acrylate is described. These alkenes present an extremely high reactivity upon Michael addition with primary amines leading to a simple, mild, and efficient route to the preparation of new polyfunctional pyrrolidinones.     

Laser-induced thin film formation from a gaseous mixture of trimethylsilylacetylene and methyl acrylate

Under irradiation with N₂ laser light, gaseous trimethylsilylacetylene (TMeSiA) and a gaseous mixture of TMeSiA and methyl acrylate (MA) produced thin films on an incident optical quartz window of an irradiation vessel. The product yield decreased with increasing partial pressure of TMeSiA. From the analysis of FT-IR spectra and X-ray photoelectron spectra of the deposited films, it was shown that Si---C bond of TMeSiA was cleaved by a two-photon absorption of N₂ laser light to produce trimethylsilyl radical and the silanes, R(CH₃)Si=CH₂ (R: H₃C---, CHC---). Trimethylsilyl radical reacted with MA at C=C and C=O bonds to produce Si---C and Si---O bonds in the film deposited from the gaseous mixture. The silanes were polymerized in each other to produce a thin film from pure TMeSiA vapor. Under irradiation with a medium pressure mercury lamp, a gaseous mixture of TMeSiA and MA produced aerosol particles in addition to the film. Polymeric species of TMeSiA was more involved in the aerosol particles rather than in the film, suggesting that collisionally induced chemical reaction takes place efficiently between excited MA and TMeSiA molecules.     

Interpolymer complexes of poly(acrylic acid) with poly(2-hydroxyethyl acrylate) in aqueous solutions

Complexes formed from poly(acrylic acid) and poly(2-hydroxyethyl acrylate) were studied in aqueous solutions by viscometric, turbidimetric, FTIR spectroscopic, and thermogravimetric analysis methods. The formation of interpolymer complexes stabilized by hydrogen bonds was observed. It was found that the compositions of these interpolymer complexes are strongly dependent on the concentration of polymers, the order of mixing the solutions, and the pH. It was demonstrated that the complexation ability of poly(2-hydroxyethyl acrylate) is relatively low compared to other known nonionic water-soluble polymers. However, it can be significantly increased via hydrophobic modification of the poly(acrylic acid) using cetyl pyridinium bromide.     

The reaction of dihydridotetrakis(triphenylphosphane)ruthenium(II) with methyl acrylate. Crystal structure of bis(methylacrylate)bis(triphenylphosphane)(aqua)ruthenium(0)

The complex H₂Ru(PPh₃)₄ reacts with methyl acrylate to give bis(methylacrylate)bis(triphenylphosphane)ruthenium(0). Temperature-dependent NMR spectra show that the complex exists in two isomeric forms in solution. The major form (ca. 74%) has one methyl acrylate ligand η²-coordinated and the other η⁴ -coordinated as a 1-oxabutadiene ligand. This complex reacts with water to give the monoaqua adduct, the crystal structure of which is reported.     

Solution properties of poly(methyl acrylate) and (1:1) poly(styrene-co-methyl acrylate)

Poly(methyl acrylate) (PMA) and 1:1 poly(styrene-co-methyl acrylate) (PSMA) were prepared by solution and bulk polymerization, respectively. The copolymer was analyzed with NMR to ascertain its composition and microstructure. The solution properties of unfractionated PMA and fractionated PSMA in ethyl acetate were investigated by light-scattering and viscosity techniques at 35°C. Narrow composition heterogeneity as revealed from the light-scattering measurements in different solvents justified the use of a single solvent for the copolymer characterization. The equations relating the limiting viscosity number to molecular weight, the molecular dimension to molecular weight, etc., were found for homopolymer and copolymers in ethyl acetate at 35°C. In the evaluation of the Flory constant K for the unperturbed state by methods based on Flory-Fox-Schaefgen, Kurata-Stockmayer, and Stockmayer-Fixman expressions, only the first method gave a value for PMA in ethyl acetate, consistent with that obtained in other solvents, whereas similar values of K were obtained by the three methods for PSMA in ethyl acetate. The studies indicate reduced thermodynamic interaction for PSMA–ethyl acetate compared to PMA–ethyl acetate, but increased steric effect in the copolymer compared with the homopolymer.     

Microstructure of poly(methyl methacrylate-co-isopropyl acrylate) studied by 13C NMR

The distribution of configurational–compositional sequences of poly(methyl methacrylate-co-isopropyl acrylate) (PMMA/iPrA) has been determined from the carbonyl and β-CH₂ signals in the 100?MHz ¹³C NMR spectra of the copolymer. The carbonyl signal provided information on configurational–compositional sequences up to heptads, whereas β-CH₂ signals offered complementary information on even sequences up to hexads. The assignment of the sequences to the respective signals was based on a comparison with the spectra of respective homopolymers, that is, PMMA and PiPrA followed by a computer simulation applying an incremental calculation of chemical shifts of the individual sequences.     

Microstructural study of poly(methyl methacrylate-co-n-propyl acrylate) by 13C NMR

Analysis of carbonyl and β-CH₂ signals in the 100?MHz ¹³C NMR spectra of poly(methyl methacrylate-co-n-propyl acrylate) (PMMA/nPrA), provided distribution of configurational-compositional sequences for a series of the copolymer samples of different composition at pentad level for carbonyl signal and hexad level for the backbone methylene carbons. Computer simulation of the spectra based on incremental calculation of the chemical shifts for individual sequences provided very good agreement with the experimental spectra.     

Reversible addition-fragmentation chain transfer radical copolymerization of β-pinene and methyl acrylate

The feasibility of radical copolymerization of β-pinene and methyl acrylate (MA) was clarified for the first time. The monomer reactivity ratios were evaluated by Fineman-Ross, Kelen-Tudos and non-linear methods, respectively. The obtained values were r_β-pinene ∼ 0 and r_MA ∼ 1.3, indicating that the copolymerization led to polymers rich in methyl acrylate units and randomly alternated by single β-pinene unit. The addition of Lewis acid Et₂AlCl to the AIBN-initiated copolymerization enhanced the incorporation of β-pinene. Furthermore, the possible controlled copolymerization of β-pinene and MA was then attempted via the reversible addition-fragmentation transfer (RAFT) technique. The copolymerization (f_β-pinene = 0.1) using 1-methoxycarbonyl ethyl dithiobenzoate (MEDB) as a RAFT agent gave copolymers with lower molecular weight and narrower molecular weight distribution. However, the presence of MEDB strongly retarded the copolymerization. Thus a new RAFT agent 1-methoxycarbonyl ethyl phenyldithioacetate (MEPD), which gives a less stable macroradical intermediate than MEDB, was synthesized and introduced to the copolymerization. As anticipated, a much smaller retardation was observed. Moreover, the copolymerization displayed a somewhat controlled features within a certain overall conversion (<∼40%).     

Stereoregularity of poly(methyl acrylate)

The stereoregularity of poly(methyl acrylate) and poly(methyl acrylate-αd) was determined from the NMR spectra. A method of quantitative determination of stereoregularity of poly(methyl acrylate) proposed in this paper is based on the fact that in the 100 Mc./sec. NMR spectrum the absorption peaks due to methylene protons in syndiotactic configurations overlap absorptions due to only one of two methylene protons in isotactic configurations. The stereostructure of poly(methy1 acrylates) polymerized with anionic catalysts such as Grignard reagents, n-butyllithium, and LiAlH₄ is generally richer in isotactic diads than in syndiotactic diads. For example, poly(methyl acrylate) polymerized with phenylmagnesium bromide as catalyst at ?20°C. consists of 99% isotactic and 1% syndiotactic diads. In radical polymerization, the isotacticity of poly(methyl acrylate) is independent of polymerization temperature. Poly(methyl acrylates) polymerized with a Ziegler-Natta catalyst consisting of Al(C₂H₅)₂Cl and VCl₄ have configurations similar to those polymerized by radical initiators. The stereoregularity of poly(methyl acrylate-α-d) resembled that of poly(methyl acrylate) polymerized under the same conditions.     

Straightforward synthesis of poly(lauryl acrylate)-b-poly(stearyl acrylate) diblock copolymers by ATRP

Lauryl (LA) and stearyl (SA) acrylates were successfully polymerized by atom transfer radical polymerization (ATRP), leading to well defined homopolymers and diblock copolymers (PDI < 1.2). Interestingly, the polymerization was very well controlled using N,N,N′,N″,N″-pentamethyldiethylenetriamine (PMDETA), a ligand which had initially been reported to be unadvisable for the polymerization of such monomers. Both kinetic studies and chain extension reactions supported our conclusions. A PLA₆₅-b-PSA₄₇ diblock copolymer was characterized by differential scanning calorimetry and dynamic thermo-mechanical analysis, revealing that both blocks exhibit side-chain crystallinity and phase segregate in the crystalline state. The diblock behaves as a brittle rigid polymer when both blocks are crystalline, as a ductile material after the melting of the PLA phase and becomes a viscous liquid when both blocks are molten. This work could be extended to the preparation of PSA-b-PLA-b-PSA bio-issued thermoplastic elastomers.     

Tail-to-tail dimerization of methyl acrylate in the presence of triphenylarsine ruthenium complexes

Catalytic dimerization of methyl acrylate by homogenous ruthenium catalysts was investigated. The effect of the addition of acidic additives, supporting ligands, polymerization inhibitor, and reaction conditions on the selectivity of dimerization was studied, and possible reaction mechanism was discussed. Conversion and selectivity were significantly affected by using triphenylarsine as supporting ligand. Under mild conditions, conversion up to 98% with good selectivity to tail-to-tail product was achieved.