油田用水基纳米聚硅增注剂的制备及其性能研究

以超疏水的纳米聚硅乳液为前躯体,选用复配的表面活性剂,将超疏水的纳米聚硅核均匀分散在水中,制备了水基纳米聚硅乳液.该乳液分散性和稳定性较好,可以完全用水取代柴油作携带介质将纳米聚硅材料带入井下.模拟岩芯驱替试验表明岩芯经水基纳米聚硅乳液处理后,水的流速平均从0.250 mL/m in增加到0.475mL/m in,增加了90.0%,增注效果十分显著.岩芯的X射线光电子能谱分析显示,纳米聚硅和表面活性剂能吸附在岩石表面上,改变岩石表面的润湿性,提高水相相对渗透率.     

无皂相反转乳化法制备高分子水基分散体系

高分子树脂水基分散体系是指高分子树脂以微粒形式分散于水中 ,包括高分子乳液、高分子悬浮液等体系 .由于高分子树脂水基分散体系具有低成本 ,高性能 ,无污染等优点 ,一直受到普遍关注 .高分子树脂乳液一般通过乳液聚合制备 .该方法只适用于由含双键的单体制备的加聚产物 .而在制备缩聚产物的乳液时 ,乳液聚合方法局限性很大 ,而最近发展起来的相反转乳化技术 ,适用于制备包括加聚产物和缩聚产物在内的大多数高分子水基分散体系 ,拓宽了高聚物水基分散体系的范围 [1] .杨振忠等 [2～ 5] 利用相反转乳化技术制备了未固化和可固化的环氧树脂…     

无皂相反转乳化法制备高分子水基分散体系

高分子树脂水基分散体系是指高分子树脂以微粒形式分散于水中, 包括高分子乳液、高分子悬浮液等体系. 由于高分子树脂水基分散体系具有低成本, 高性能, 无污染等优点, 一直受到普遍关注.     

双酚A型环氧树脂水基化微粒分析

高分子树脂水基化微粒化就是使高分子树脂以微粒形式分散于水中,高分子乳液、悬浮液都属于此范畴．因其不含有机溶剂,且具有无环境污染及不易失火等优点,放这方面的研究正成为高分子技术的一个研究热点．通常的乳液聚合或悬浮聚合方法是从小分子单体到聚合物水基化体系的化学反应过程,一般只适于制备加聚物的水基化体系,而不适用于制备维聚物的水基化体系．本文提出的相反转技术是一种有效的制备高分子水基化体系的方法,它能将几乎所有的高分子树脂通过物理的乳化方法制成相应的水基化体系[1,2],大大拓宽了其制备范围．相反转[3。4]…     

不同功能化基团修饰的硅壳纳米颗粒分散性研究

采用反相微乳液体系中功能化基团同步修饰(油相修饰)以及反相微乳液制备纳米颗粒后再通过功能化基团后续修饰(水相修饰)的方法分别制备了纯硅壳纳米颗粒(SiNP)、氨基化硅壳纳米颗粒(NSiNP)、羧基化硅壳纳米颗粒(CSiNP)和聚乙二醇硅壳纳米颗粒(PSiNP). 通过沉降时间和离心速度观察了不同方法获得的不同功能化基团修饰的硅壳纳米颗粒在水中的分散及稳定性, 并采用激光粒度仪、透射电子显微镜对分散效果进行了分析. 结果表明, 采用同一修饰方法分别制备的纳米颗粒在水中的分散及稳定性顺序是CSiNP≥PSiNP>SiNP>NSiNP; 油相修饰法获得的CSiNP和PSiNP的分散性要优于水相修饰法获得的. PSiNP和CSiNP在Hela细胞表面的非特异性吸附非常小, 而NSiNP却显示了强烈的细胞非特异性吸附.     

油溶性金属Ni纳米微粒的制备与表征

纳米材料的制备、性能与应用已成为近年来的研究热点之一犤１犦。由于在催化、光学和电学材料中的广泛应用，超细单分散的金属微粒的制备与性质已引起人们的广泛兴趣。通常制备金属纳米微粒的方法有两种：一是把固体金属材料分裂为纳米尺寸的颗粒，如机械粉碎、电弧放电及金属原子蒸气沉积犤２犦，用这种方法制备的金属微粒粒径一般都比较大，且粒子尺寸分布宽，另一种是把金属原子制成纳米尺度的颗粒，如乳液聚合法犤３犦、热解犤４犦、γ－射线辐照犤５犦、脉冲电沉积犤６犦和化学还原犤７犦等，这种方法制备的微粒粒径通常分布窄且粒子小…     

沉淀法高效制备聚多巴胺纳米粒子

为得到分散性和稳定性较好的聚多巴胺纳米粒子,利用“沉淀-再分散法”高效制备了聚多巴胺纳米粒子水分散液。 首先利用溶液氧化法制备了分散在水/乙醇中的聚多巴胺纳米粒子,然后向分散液中加入丙酮使聚多巴胺纳米粒子絮凝。 收集沉降物,用丙酮冲洗并干燥后,加水重新分散得到纯化的聚多巴胺纳米粒子水分散液。 丙酮沉淀法得到的聚多巴胺纳米粒子形貌规整,分散性好,粒径分布在250 nm左右,在水中具有良好的储存稳定性和光热性能,与传统的超速离心提纯法相比,产率可提高57.4%。 此方法为其之后在药物载体及光热治疗等方面的应用研究提供了便利。     

乳化剂分子亲水组分含量对相反转乳化过程的影响

高分子树脂水基分散体系 ,因其结构的可灵活调节性 ,在许多方面得到应用 ,又因其不含有机溶剂 ,能完全满足环境保护和生态的要求而备受关注 [1～ 3] .相反转乳化技术是制备高分子水基体系的新方法 ,它适用于制备包括加聚物和缩聚物的大多数高分子水基体系 ,大大拓宽了水基体系的范围 [4 ] .杨振忠等[5] 利用自己合成的高分子非离子型乳化剂将环氧树脂乳化成微粒尺寸小且分布窄的水基分散体系 ,对相反转机理和相反转技术进行了深入研究 .研究表明 ,乳化剂浓度和乳化温度对相反转后水基微粒尺寸和形态有重要影响 ,高乳化剂浓度和较低的乳化温…     

两亲性树状接枝己内酯共聚物的合成与表征

通过树状接枝聚己内酯的侧羟基及端羟基与氯甲酰化的聚乙二醇进行接枝反应,得到带有亲水性聚乙二醇链段的新型两亲性树状接枝共聚物.1H-NMR分析显示,接枝率为50%左右.GPC分析结果表明,共聚物分子量呈较窄的单峰分布,分子量与接枝前相比明显增高.两亲性共聚物能直接分散在水中形成胶束溶液.以芘为荧光探针的测试结果表明其临界胶束浓度有降低.动态光散射测得胶束平均粒径在16至31 nm之间,粒径分散指数适中,PDI在0.25至0.39之间.TEM显示胶束粒子为不规整球形,由更小的粒径为几个纳米的微粒聚集而成,这些微粒的大小刚好与单个大分子的尺寸相匹配.因此,两亲性树状接枝聚己内酯在水相中存在单分子胶束与多分子组装胶束的平衡.得益于支化聚合物结构中的纳米空腔,两亲性树状接枝聚合物胶束对紫杉醇具有优良的包载能力.     

无皂乳液聚合法制备Fe3O4@P(St-GMA)复合微球

用化学共沉淀法制备了磁性四氧化三铁纳米粒子. 在油酸和氨水的作用下, 使之分散在水中, 得到了水分散的磁流体. 在水基磁流体的存在下, 进行苯乙烯和甲基丙烯酸缩水甘油酯(GMA)的无皂乳液共聚合, 得到了Fe₃O₄@P(St-GMA)复合微球. 综合考察了反应温度、磁流体和单体的用量、引发剂的用量对聚合转化率的影响, 并用TEM, TGA和VSM对磁性复合微球进行了表征.     

Sonochemical production of fluorescent and phosphorescent latex particles

A novel method for producing nanosized polymer latex particles doped with fluorescent and phosphorescent solutes is described. Methyl methacrylate monomer (10 wt %) containing either pyrene, 4-dicyanomethylene-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran (DMDP), or 1-bromonaphthalene was ultrasonically dispersed in water and simultaneously polymerized to produce approximately 60 nm diameter latex particles. A fluorescence spectroscopic examination of the latex dispersion containing either pyrene or DMDP showed that the solutes were not covalently bound to the polymer and that they were embedded in a highly viscous environment possessing a low polarity (dielectric constant on the order of 2). The fluorescence lifetime of the pyrene in the core of the poly(MMA) latex was found to be 520 ns, irrespective of the oxygen concentration in the dispersion. Room-temperature phosphorescence was observed from 1-bromonaphthalene, with a lifetime of 2.0 ms in an argon atmosphere. In the presence of air, phosphorescence was still observable although with a partially reduced emission intensity.     

复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究

将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .     

低渗透油田增注用SiO_2纳米微粒的制备和表征

用原位表面修饰法制备了低渗透油田增注用SiO2纳米微粒,用透射电镜、X射线粉末衍射、红外光谱和热分析等手段对其形貌、化学结构和热力学性质进行了研究,考察了其在有机介质中的分散性.结果表明经表面修饰的SiO2纳米微粒在柴油、液体石蜡中有很好的亲油性,岩心驱替试验表明该材料能有效提高水相渗透率.     

The preparation and characterization of amphiphilic core/shell particles

Colloidal amphiphilic particles were prepared with hydrophilic polyacrylamide cores encapsulated by hydrophobic poly(butyl methacrylate) shells. The hydrophobic shell possessed a porous structure, which made the hydrophilic core accessible to the outside liquid. The amphiphilicity of the particles was characterized by their water and diesel oil absorbabilities. The effect of the polymerization conditions on the structure and thickness of the hydrophobic layer was investigated in some detail. Such amphiphilic particles can be dispersed in both water and hydrophobic liquids, and the dispersions have a long life in water and a more moderate one in oil.     

Synthesis and characterization of fluorine‐containing polyacrylate latex with core–shell structure by UV‐initiated seeded emulsion polymerization

A core–shell fluorine‐containing polyacrylate emulsion was successfully prepared by UV‐initiated seeded emulsion polymerization in two stages in the presence of two photoinitiators. The water‐soluble photoinitiator for the core polymerization and the oil‐soluble photoinitiator was used for the shell polymerization. Both of the two stage polymerizations could be completed within 15 min and displayed a conversion above 94%. The emulsion and the films were characterized by Fourier transformed infrared spectrometry, transmission electron microscopy, dynamic light scattering, X‐ray photoelectron spectroscopy (XPS), contact angle (CA), and thermogravimetry analysis, respectively. The analysis results indicated that the fluorine‐containing latex particles had very small particle size (40 nm) with a core–shell structure and a narrow particle size distribution. XPS analysis revealed that a gradient concentration of fluorine excited in fluorine‐containing emulsion film from the film–air interface to the film–glass interface. In addition, the film formed from the fluorine‐containing emulsion exhibited not only higher thermal stability but also better hydrophobicity than that of the fluorine‐free emulsion. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation of sulphonate-containing core/shell latex particles via seeded emulsion copolymerization

<正>In this study,P(St-MAA) seed latex particles were first prepared via soap-free emulsion polymerization of styrene(St) and methacrylic acid(MAA),then the seed particles were allowed to swell with St at room temperature,and the P(St-MAA)/P(StNaSS) core/shell latex particles were then synthesized via seeded emulsion copolymerization of St and sodium styrene sulphonate (NaSS) using AIBN as initiator in the presence of N,N'-methylenebisacrylamide(BAA,water-soluble crosslinker).Results showed that the polymerization could be carried out smoothly when the ratio of BAA to total monomers was less than 3 mol%,the narrow dispersed P(St-MAA) seed particles with the diameter of 150 nm and the P(St-MAA)/P(St-NaSS) core/shell latexes with the particle size of about 200 nm were synthesized.When the 25/75 mole ratio of NaSS/(St + MAA) and 2 mol%of BAA were used in the seeded emulsion polymerization,the resulted P(St-MAA)/P(St-NaSS) latex product showed a low weight loss after water extraction,and the NaSS unit content in the whole particle and in the shell reached 11.7 mol%and 34.6 mol%,respectively.     

反应性复合乳液的合成、表征及其交联反应

利用种子半连续乳液聚合方法合成了核层或壳层带有环氧基以及壳层带有羧基的3种不同核/壳结构的乳胶粒子,通过物理共混带环氧基和羧基的乳胶粒子,得到了两种反应性复合乳液.利用透射电镜和激光动态光散射对乳胶粒子进行了表征,其粒径分布较窄,粒径分布的多分散系数为0.062,平均粒径约76 nm,乳胶粒子具有明显的核/壳结构.通过胶膜的凝胶率和膨胀率的测定和红外光谱分析对反应性复合乳液中乳胶粒子的扩散及交联反应进行了研究,并探讨了不同核壳结构复合乳液对涂膜机械性能的影响.研究表明,当反应性复合乳液中的环氧基和羧基分别分布在乳胶粒子的核层和壳层时,有利于聚合物分子链的充分扩散和化学交联反应的进行,从而提高涂膜的物理化学性能,当甲基丙烯酸缩水甘油酯(GMA)含量为10 wt%时,涂膜的拉伸强度达20.3 MPa.     

Facile Microfluidic Fabrication of Biocompatible Hydrogel Microspheres in a Novel Microfluidic Device

Poly(ethylene glycol) diacrylate (PEGDA) microgels with tuneable size and porosity find applications as extracellular matrix mimics for tissue-engineering scaffolds, biosensors, and drug carriers. Monodispersed PEGDA microgels were produced by modular droplet microfluidics using the dispersed phase with 49–99 wt% PEGDA, 1 wt% Darocur 2959, and 0–50 wt% water, while the continuous phase was 3.5 wt% silicone-based surfactant dissolved in silicone oil. Pure PEGDA droplets were fully cured within 60 s at the UV light intensity of 75 mW/cm². The droplets with higher water content required more time for curing. Due to oxygen inhibition, the polymerisation started in the droplet centre and advanced towards the edge, leading to a temporary solid core/liquid shell morphology, confirmed by tracking the Brownian motion of fluorescent latex nanoparticles within a droplet. A volumetric shrinkage during polymerisation was 1–4% for pure PEGDA droplets and 20–32% for the droplets containing 10–40 wt% water. The particle volume increased by 36–50% after swelling in deionised water. The surface smoothness and sphericity of the particles decreased with increasing water content in the dispersed phase. The porosity of swollen particles was controlled from 29.7% to 41.6% by changing the water content in the dispersed phase from 10 wt% to 40 wt%.     

Highly magnetic latexes from submicrometer oil in water ferrofluid emulsions

The synthesis of functionalized submicrometer magnetic latex particles is described as obtained from a preformed magnetic emulsion composed of organic ferrofluid droplets dispersed in water. Composite (polystyrene/γ‐Fe₂O₃) particles were prepared according to a two‐step procedure including the swelling of ferrofluid droplets with styrene and a crosslinking agent (divinyl benzene) followed by seeded emulsion polymerization with either an oil‐soluble [2,2′‐azobis(2‐isobutyronitrile)] or water‐soluble (potassium persulfate) initiator. Depending on the polymerization conditions, various particle morphologies were obtained, ranging from asymmetric structures, for which the polymer phase was separated from the inorganic magnetic phase, to regular core–shell morphologies showing a homogeneous encapsulation of the magnetic pigment by a crosslinked polymeric shell. The magnetic latexes were extensively characterized to determine their colloidal and magnetic properties. The desired core–shell structure was efficiently achieved with a given styrene/divinyl benzene ratio, potassium persulfate as the initiator, and an amphiphilic functional copolymer as the ferrofluid droplet stabilizer. Under these conditions, ferrofluid droplets were successfully turned into superparamagnetic polystyrene latex particles, about 200 nm in size, containing a large amount of iron oxide (60 wt %) and bearing carboxylic surface charges. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2642–2656, 2006