Nanowear studies in chemically heterogeneous responsive polymeric brushes by surface force microscopy

In this study, we present nanowear studies using surface force microscopy (SFM), on nanoscopic thin films of reversibly switchable binary polymer brushes [polystyrene (PS) + poly(2-vinylpyridine) (P2VP)] and respective monobrushes [polystyrene and poly(2-vinylpyridine)] synthesized via “grafting to” method. The aim was to tune the wear in nanothin polymer brush surfaces. Therefore, the effect of conformational switching of PS + P2VP brush on treatment with selective solvents for PS and P2VP chains on the wear process was investigated. Wear process on thick spin-coated films of PS and P2VP was also investigated for comparison. Nanowear experiments were performed using SFM tip by repeating scans over the surface to follow the wear process closely. The wear process on different surfaces was explained on the basis of molecular entanglement as well as adhesion and friction on the sample surface. For spin-coated PS film as well as PS and PS + P2VP brush surfaces (treated with toluene) with molecular entanglements at surface, wear mechanism involved formation of ripples. However, in case of spin-coated P2VP films as well as P2VP and PS + P2VP brush surfaces (treated with ethanol) with no molecular entanglements at surface, wear occurred via removal of polymer chains and their accumulation at the rim. For PS + P2VP surface treated with acidic water, wear mechanism was complex and inhomogeneous ripple formation was followed by formation of heaps of polymeric material in the center of scanned area. The extent of wear as measured either by root mean square roughness of the surface or spacing between the ripples, increased with the number of scans for all the surfaces. Our study shows that wear mode of polymer brush surfaces is different for different polymers and can be controlled/tuned by the use of binary polymer brushes.     

Synthesis and characterization of poly(amideimide)s containing pendent flexible alkoxy chains

A series of aromatic diacylhydrazides containing pendent flexible alkoxy chains, viz., 5-butyloxyisophthalicacid dihydrazide, 5-octyloxyisophthalicacid dihydrazide, 5-dodecyloxyisophthalicacid dihydrazide and 5-hexadecyloxyisophthalicacid dihydrazide were synthesized by the hydrazinolysis reaction of the corresponding aromatic esters with hydrazine hydrate. Diacylhydrazides were each polycondensed with aromatic dianhydrides, viz., 4,4′-oxydiphthalic anhydride (ODPA), 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) and pyromellitic dianhydride (PMDA) to obtain new poly(amideimide)s. Poly(amideimide)s had inherent viscosity in the range 0.55-0.88 dL/g in N,N-dimethylacetamide (DMAc) at 30 ± 0.1 °C. Poly(amideimide)s were found to be soluble in DMAc, N,N-dimethylformamide (DMF), 1-methyl-2-pyrrolidinone (NMP) and pyridine and could be cast into tough, flexible and transparent films from a solution in DMAc. X-ray diffractograms revealed that poly(amideimide)s with longer alkoxy chains had layered structures. Glass transition temperature of poly(amideimide)s containing pendent flexible alkoxy chains were in the range 215-245 °C. Temperature at 10% weight loss was in the range 380-410 °C in nitrogen atmosphere indicating good thermal stability of poly(amideimide)s.     

AGET ATRP of methyl methacrylate with poly(ethylene glycol) (PEG) as solvent and TMEDA as both ligand and reducing agent

Activator generated by electron transfer atom transfer radical polymerization of methyl methacrylate (MMA) in inexpensive, non-toxic poly(ethylene glycol) (PEG), with air-stable Cu(II)X₂(X = Br, Cl) as the catalyst and N,N,N′,N′-tetramethylethylenediamine (TMEDA) as both ligand and reducing agent was investigated. The polymerizations in PEG proceeded in a well-controlled manner as evidenced by kinetic studies and chain extension results. The polydispersity of the polymer obtained was quite narrow, with a weight-average molecular weight/number-average molecular weight ratio of less than 1.2. Effects of the TMEDA content and the catalysts on polymerization were also investigated, respectively.     

A novel ternary polymer electrolyte for LMP batteries based on thermal cross-linked poly(urethane acrylate) in presence of a lithium salt and an ionic liquid

A new ternary polymer electrolyte based on thermally cross-linked poly(urethane acrylate) (PUA), lithium bis(trifluoromethansulfonyl)imide (LiTFSI) and the ionic liquid N-butyl-N-methylpyrrolidinium TFSI (PYR₁₄TFSI) was developed and tested for application in LMP batteries. The polymer electrolyte was a transparent yellow self-standing material with quite good mechanical properties, i.e., comparable to that of a flexible rubber. The room temperature ionic conductivity of the dry polymer electrolyte was found to be as high as 0.1 mS cm⁻¹ for the compound containing 40 wt% of ionic liquid (PYR₁₄TFSI) and a O/Li ratio of 15/1 (Li⁺ from LiTFSI). The thermal analysis of the new cross-linked electrolyte showed that it was homogeneous, amorphous and stable over a wide temperature range extending from −40 °C to 100 °C. The homogeneity of the polymer electrolyte was also confirmed by SEM analysis.     

Homo and block copolymers of tert-butyl methacrylate by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of tert-butyl methacrylate (tBMA) was investigated using cuprous bromide with different ligands, solvents, deactivators, etc. The polymerization in bulk and diphenyl ether solvent system performed using Cu(I)Br complexed with N, N, N′, N″, N″-pentamethyldiethylenetriamine (PMDETA) catalyst in conjunction with 2-bromopropionitrile as an initiator at room temperature showed a curvature in the first-order kinetic plot. The controlled polymerization in methanol solution resulted in slower rate of polymerization and lower molecular weights. Well-defined diblock copolymers of PSt-b-PtBMA synthesized by polystyrene bromo macroinitiator (PSt-Br) with Cu(I)Cl/PMDETA catalyst system yielded predetermined molecular weights and lower polydispersities. Otherwise, the Cu(I)Br/PMDETA catalytic system showed an inefficient polymerization of tert-butyl methacrylate with lower molecular weights and higher polydispersities. Subsequent hydrolysis of the homopolymer refluxed in dioxane with addition of HCl afforded well-defined poly(methacrylic acid).     

Synthesis of basic molecular brushes: ATRP of 4-vinylpyridine in organic media

A poly(2-(2-bromopropionyloxy)ethyl methacrylate) (PBPEM) was used as macroinitiator in the synthesis of molecular brushes with poly(4-vinylpyridine) side chains, (P(BPEM-g-4VP). Atom transfer radical polymerization (ATRP) was employed as the polymerization technique. The polymerizations were carried out in DMF at 30 °C using a copper-chloride-based ATRP catalyst, which converted all the dormant polymer chain ends to alkyl chloride groups, thus minimizing branching and crosslinking, which occurred when a copper bromide-based catalyst was employed. Tris(2-pyridylmethyl)amine was selected as the ligand due to the high activity of its Cu^I complex in ATRP as well as its strong binding to both Cu^I and Cu^II, which prevented competitive complexation of the monomer or polymer to the metal center. In order to prevent crosslinking via radical coupling, the monomer conversion was kept low (under 3%) and the alkyl chloride end groups of P4VP side chains were converted to alkoxyamines upon activation followed by a reaction with TEMPO radical. Dynamic light scattering measurements showed the hydrodynamic diameter (D_H) of the brushes was pH-dependent. Aggregation of single P(BPEM-g-4VP) brushes in water was very pronounced at high pH values but was observed even when the amount of added HCl was enough to completely protonate the pyridine units (D_H = 278 nm).     

Assessment of hydrate kinetic inhibitors with visual observations

The hydrate inhibition effect of three kinetic inhibitors (inhibex 301, 501, and 713) was assessed from (CH₄ + C₂H₆ + C₃H₈) gas mixture + brine systems using a high pressure sapphire cell. The onset time of hydrate formation was determined by visual observation method and pressure drop profile method, respectively. The experimental results demonstrated that the onset time was able to be determined by the visual observation method all the time while the pressure drop profile method failed to detect the onset time clearly and correctly at lower temperatures. In some cases, the initial appearance of hydrate crystals cannot induce a clear break in the pressure–time relationship curve. The onset time measured by the visual observation method is usually shorter than or at least the same as that determined by the pressure drop profile method. The inhibiting effect on the growth of hydrate crystals can be shown by the difference of the onset time obtained by the two methods. The maximum tolerated subcooling of each inhibitor was also investigated based on the onset time. It was found that inhibex 301 behaves as the best inhibitor that can tolerate the maximum subcooling of 8.3 K at 0.5 wt% and 10.6 K at 1.0 wt%, respectively. The maximum subcooling for inhibex 501 is 6.8 K at 0.5 wt% and 6.6 K at 1.0 wt%, respectively. Inhibex 713 has relatively poor inhibiting effect among the three inhibitors with the maximum subcooling of less than 3.5 K at 0.5 wt% and 5.1 K at 1.0 wt%, respectively.     

Preparation of macroporous monoliths based on epoxy-bearing hydrophilic terpolymers and applied for affinity separations

This work reports the synthesis and characterization of poly(N-acryloyl-tris(hydroxymethyl)aminomethane-co-glycidyl methacrylate-co-N,N′-methylenebisacrylamide) [poly(NAT-GMA-BIS)] discs using different porogenic solvents. The macroporous polymer obtained with PEG 6000 as co-porogen showed the best porous properties of the series. End-point immobilization of heparin (Hep, as ligand) was then carried out on the products through reductive amination. Thus, the products were reacted with ethylenediamine (EDA) and hexamethylenediamine (HMDA) in order to introduce amine groups and to analyze the length of the spacer on the immobilization of heparin. Then, the highest value of amine groups [1.280 and 0.919 mmol amine/g dry support for poly(NAT-GMA-BIS)-EDA and poly(NAT-GMA-BIS)-HMDA, respectively] was obtained at 40 °C after 48 h of reaction. Finally, the amount of ligand coupled to discs was not influenced by the two length spacers assayed. The amount of Hep coupled on discs [591.50 and 489.90 μg Hep/g dry polymer for poly(NAT-GMA-BIS)-EDA-Hep and poly(NAT-GMA-BIS)-HMDA-Hep, respectively] was similar to that obtained using macroporous polymer beads reported by other authors. The supports yielded were used to assay the retention of antithrombin III (AT-III). The retention was greater for the EDA-containing product with a larger amount of heparin. These novel heparin-containing macroporous poly(NAT-GMA-BIS) discs could be used as potential affinity chromatography supports.     

Preparation and characterization of novel organosoluble and thermally stable poly(benzimidazole-amide)s bearing phthalimide pendent groups

Novel aromatic poly(benzimidazole-amide)s, PBAs, have been synthesized by direct polycondensation of a new dicarboxylic acid, N-[3,5-bis(5-carboxylic acid-2-benzimidazole) phenyl]phthalimide (1), containing performed benzimidazole rings and a phthalimide pendent group with various aromatic diamines. The dicarboxylic acid was synthesized by reaction of 5-(N-phthalimide)isophthalic acid with 4-methyl-1,2-phenylenediamine in polyphosphoric acid, followed by its oxidation into relative dicarboxylic acid. To study the structure-property relationships of 1,3-bis(5-carboxylic acid-2-benzimidazole)benzene (2, as a reference) this compound was also synthesized. The chemical structure of 1 and 2 were confirmed by the spectroscopic methods and elemental analyses. The characterization of the polymers was performed with inherent viscosity measurements, solubility tests, FT-IR, Ultraviolet and ¹H NMR spectroscopy and thermogravimetry. The polymers were obtained in quantitative yields with inherent viscosities between 0.53 and 0.91 dl g⁻¹. The effects of the phthalimide pendent group on the polymer properties such as solubility and thermal behavior were investigated and compared with those of the corresponding unsubstituted poly(benzimidazole-amide)s. The modified poly(benzimidazole-amide)s showed enhanced solubilities in some solvents, such as m-cresol and pyridine, in comparison to the unmodified analogues. In addition, the incorporation of the pendent phthalimide groups in the poly(benzimidazole-amide)s backbone increased remarkably the thermal stability of the polymer. The glass transition temperature and 10% weight loss temperature of the poly(benzimidazole-amide)s were in range of 291-334 °C and 466-540 °C, respectively, in nitrogen.     

Sorption phenomena of organic solvents in polymers: Part I

In this work we use the vapor-sorption equilibrium data to show the degree of solvent upturn in each solvent-polymer system. For this purpose, 23 isothermal data sets for four polymer + solvent binaries, one block copolymer + solvent binary and for the corresponding polymer pairs have been used in the temperature range of 25-70 °C. Solvents studied are benzene, carbon tetrachloride, chloroform and pentane. Homopolymers studied are polyisobutylene, poly(ε-caprolactone), poly(ethylene oxide), n-heptadecane, polystyrene, poly(vinyl chloride), poly(vinyl methyl ether), and n-tetracosane.According to these data sets, solvent weight fraction in the polymer is plotted against solvent-vapor activity that is calculated assuming an ideal gas phase of pure solvent vapor neglecting the vapor pressure of the polymer. We use the Flory-Huggins theory to obtain dimensionless interaction parameter, χ. Also the Zimm-Lundberg clustering theory and non-ideality thermodynamic factor, Γ are used to interpret the equilibrium data.     

Clathrate hydrate formation in (methane + water + methylcyclohexanone) systems: the first phase equilibrium data

The present study experimentally demonstrated clathrate hydrate formation in the systems of (methane + water + each of the three methylcyclohexanone isomers, i.e., 2-methylcyclohexanone, 3-methylcyclohexanone, and 4-methylcyclohexanone) and measured the first data of the quadruple (water rich liquid + hydrate + methylcyclohexanone rich liquid + methane rich vapor) equilibrium pressure and temperature conditions in these systems over the temperatures from T=273 K to T=281 K. In the three systems with methylcyclohexanone, the measured equilibrium pressure at each given temperature is ∼1.3 MPa lower than that in a structure-I hydrate forming (methane + water) system without any methylcyclohexanone, which suggests the formation of structure-H hydrates with methylcyclohexanones as large-molecule guest substances. Among the three systems, 3-methylcyclohexanone provides the highest equilibrium pressure, and 2-methylcyclohexanone, the lowest.     

Photoinduced optical anisotropy in azobenzene methacrylate block copolymers: Influence of molecular weight and irradiation conditions

The photoinduced anisotropy in a series of azomethacrylate block copolymers with different molecular weights and azo contents has been investigated under several irradiation conditions. Depending on molecular weight and composition, different microstructures (disordered, lamellar, spherical) appear, due to block microsegregation. Measurements of birefringence (Δn) induced with linearly polarised 488 nm light show that the highest (and stable) Δn_N values (birefringence normalised to the azo content) are achieved in copolymers with a lamellar structure. Lower Δn_N are obtained in the copolymers in which azobenzene units segregate to nano spheres and the lowest (and less stable) Δn_N values, appear in disordered systems not showing any defined microstructure. Besides, higher Δn_N is obtained in the copolymers with larger molecular weight of the poly (methyl methacrylate) and the azo polymer blocks, both in the microspheres segregated polymers as well as in those without a clear microstructure. This behaviour is consistent with that of the photoinduced order of azobenzene units obtained from dichroism measurements. Irradiation temperature (from 30 to 90 °C) and light power (from 100 to 500 mW/cm²) also influence the photoinduced response. Photoinduced Δn_N growth rate is faster when both temperature and irradiation power increase. Furthermore, birefringence is only induced at temperatures up to 90 °C, the maximum value being obtained at about 70 °C. No clear dependence of the final Δn_N value with light power has been found.     

Conductivity and thermal behavior of proton conducting polymer electrolyte based on poly (N-vinyl pyrrolidone)

The polymer electrolytes based on poly N-vinyl pyrrolidone (PVP) and ammonium thiocyanate (NH₄SCN) with different compositions have been prepared by solution casting technique. The amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The shift in T_g values and the melting temperatures of the PVP-NH₄SCN electrolytes shown by DSC thermo-grams indicate an interaction between the polymer and the salt. The dependence of T_g and conductivity upon salt concentration have been discussed. The conductivity analysis shows that the 20 mol% ammonium thiocyanate doped polymer electrolyte exhibit high ionic conductivity and it has been found to be 1.7 × 10⁻⁴ S cm⁻¹, at room temperature. The conductivity values follow the Arrhenius equation and the activation energy for 20 mol% ammonium thiocyanate doped polymer electrolyte has been found to be 0.52 eV.     

Controlled synthesis of poly(acetone oxime acrylate) as a new reactive polymer: Stimuli-responsive reactive copolymers

Acetone oxime acrylate has been synthesized as a new active ester monomer. Free radical polymerization yielded a reactive polymer soluble in various organic solvents, such as chloroform, dioxane, DMSO, acetone, methanol, dichloromethane, DMF, and ethanol. Controlled radical polymerization of acetone oxime acrylate was successfully conducted using the RAFT, NMP and Iniferter method. Partly polymer analogous reaction with N-isopropylamine resulted in the reactive copolymer poly(N-isopropylacrylamide-co-acetone oxime acrylate), which featured a lower critical solution temperature (LCST) of 61 °C in water. Further, the reactivity of the copolymer was exemplary proven by complete reaction with ammonia yielding poly(N-isopropylacrylamide-co-acrylamide), which does not possess a LCST.     

Characterisation of N-vinyl-2-pyrrolidone-based hydrogels prepared by a Diels-Alder click reaction in water

N-vinyl-2-pyrrolidone-based hydrogels were prepared by the Diels-Alder reaction in water for the first time. Copolymers of N-vinyl-2-pyrrolidone(VP) and furfuryl methacrylate(FM) were synthesised by free radical polymerisation in toluene at 70 °C by using 2,2′-azobisisobutyronltrile as an initiator. Polymeric dienophile (PEG-AMI) was prepared from N-alaninyl maleimide (AMI) and poly(ethylene glycol) (PEG) by using N,N′-dicyclohexylcarbodiimide (DCC) as a dehydrating agent. The prepared dienes and dienophile were then dissolved in water and mixed, leading to gelation via Diels-Alder reaction after some time. The gelation times of different copolymers and PEG-AMI in different solvents and at different temperatures were measured by the vial inversion method, and the swelling behaviour of dried hydrogels was studied using a general gravimetric method. The gelation time was shorter in water than in organic solvents, and the gelation time decreased with the increase of temperature and FM content in copolymers. Conversely, the swelling ratios increased with the decrease of temperature and FM content in the copolymers. Disassembly experiments suggested that N,N-dimethylformamide (DMF) could accelerate the retro-DA reaction.     

Miscibility and interactions of polystyrene/polyolefine and polystyrene/poly(n-alkyl methacrylate) mixtures in dilute xylene solutions

The miscibility and intermolecular interactions between polystyrene (PS) and poly(ethylene-co-propylene) (EPC), as well as between PS and long-chain poly(alkyl methacrylates) (PAMA), namely, poly(dodecyl methacrylate) (PDDMA) and poly(octadecyl methacrylate) (PODMA), in dilute xylene solutions at 30 °C were studied. Investigated polymers are widely used as rheology modifiers, i.e. viscosity index improvers and pour point depressants for lubricating mineral oils. The specific and reduced viscosities of two- and three-component polymer solutions as well as intrinsic viscosities and Huggins’ parameter values were determined as functions of the polymer mixture composition and overall polymer concentration. The reduced viscosity was found to be linearly dependent on the overall polymer concentration. The observed viscosities of polymer mixtures were intermediate to those of the mixture constituents; the values decrease in the order: EPC > PS > PAMA. The specific viscosities of all the polymer mixtures obtained as the experimental results and calculated applying the Catsiff-Hewett and Krigbaum-Wall theoretical equations were considered. Since all the polymer/polymer pairs showed the negative viscometric interaction parameter values (Δb₁₂ < 0), the PS/EPC and EPC/PAMA mixtures were found to be immiscible. The observed repulsive molecular interactions originate from the differences in polymer composition and molar masses. This conclusion was supported by calculations employing the group contribution approach of Coleman, Graf and Painter. The calculated values of interaction parameters for (co)polymer blends, Λ₁₂, were 5.47, 6.42 and 13.1 J cm⁻³ for PS/PDDMA, PS/PODMA and PS/EPC, respectively.     

Adsorption of poly(N-isopropylacrylamide-co-4-vinylpyridine) onto core-shell poly(styrene-co-methylacrylic acid) microspheres

Adsorption of the thermoresponsive copolymer of poly(N-isopropylacrylamide-co-4-vinylpyridine) (PNIPAM-co-P4VP) onto the core-shell microspheres of poly(styrene-co-methylacrylic acid) (PS-co-PMAA) is studied. The core-shell PS-co-PMAA microspheres are synthesized by one-stage soap-free polymerization in water. The copolymer of PNIPAM-co-P4VP is synthesized by free radical polymerization of N-isopropylacrylamide and 4-vinylpyridine in the mixture of DMF and water using K₂S₂O₈ as initiator. Adsorption of PNIPAM-co-P4VP onto the core-shell PS-co-PMAA microspheres results in formation of the composite microspheres of PS/PMAA-P4VP/PNIPAM. The driven force to adsorb the copolymer of P4VP-co-PNIPAM onto the core-shell PS-co-PMAA microspheres is ascribed to hydrogen-bonding and electrostatic affinity between the P4VP and PMAA segments. The resultant composite microspheres of PS/PMAA-P4VP/PNIPAM with surface chains of PNIPAM are thermoresponsive in water and show a cloud-point temperature at about 33 °C.     

Sorption phenomena of organic solvents in polymers: Part II

In this work we use the vapor-sorption equilibrium data to show the degree of solvent upturn in each solvent-polymer system. For this purpose, sixty-one isothermal data sets for forty copolymer + solvent binaries and for fourteen of their parent homopolymer + solvent binaries have been used in the temperature range of 23.5-80 °C. Solvents studied are acetone, acetonitrile, 1-butanol, 1,2-dichloroethane, chloroform, cyclohexane, hexane, methanol, octane, pentane, and toluene. Copolymers studied are poly(acrylonitrile-co-butadiene), poly(styrene-co-acrylonitrile), poly(styrene-co-butadiene), poly(vinyl acetate-co-ethylene), and poly(vinyl acetate-co-vinyl chloride). All copolymers are random copolymers. Some homopolymers are also studied: polyacrylonitrile, poly(cis-1,4-butadiene), poly(ethylene oxide), polystyrene and poly(vinyl acetate).According to these data sets, solvent weight fraction in the polymer is plotted against solvent vapor activity that is calculated assuming an ideal gas phase of pure solvent vapor neglecting the vapor pressure of the polymer. We use the Flory-Huggins theory to obtain dimensionless interaction parameter, χ. Also the Zimm-Lundberg clustering theory and non-ideality thermodynamic factor, Γ are used to interpret the equilibrium data.     

Influence of hydrophobe content on the solution rheology of hydrophobically modified terpolymer of SO2, N,N-diallyl-N-carboethoxymethylammonium chloride

Rheological properties of hydrophobically modified copolymer of SO₂, N,N-diallyl-N-carboethoxymethylammonium chloride and the hydrophobic monomer N,N-diallyl-N-octadecylammonium chloride were studied. The influence of hydrophobe content (HP) and polymer concentration was investigated. Polymers with HP content in the range 1.5-5% were examined and the concentration was varied in the range 2-5 wt%. Both dynamic and steady-shear experiments were performed in ARES rheometer. Copolymers were observed to exhibit typical viscoelastic behavior even with low HP content. Both the dynamic viscosity, η′ and storage modulus, G′, increase with the increase of both the polymer concentration and the HP content of the system. The viscosity of the high HP content polymer showed a strong shear dependency, while G′ was a weak function of frequency and gel-like behavior was observed. The zero-shear viscosity, η₀, showed a strong concentration dependency (η₀ ∼ ?^α; 1.1 < α < 5.9). The concentration dependency of η₀ suggests that intermolecular association is dominant in the high HP content polymer. Control of the HP content and polymer concentration of this class of polymers can lead to a wide range of interesting rheological properties.     

Synthesis of aromatic poly(amide-imide)s from novel diimide-diacid (DIDA) containing sulphone and bulky pendant groups by direct polycondensation with various diamines

A novel diimide-diacid (DIDA) monomer, 4-{4-[(4-methyl phenyl) sulphonyl]}-1,3-bis-trimellitoimido benzene containing sulphone and bulky pendant groups was successfully synthesized and used to synthesize a series of wholly aromatic poly(amide-imide)s (PAIs) by direct polycondensation method. The direct polycondensation of newly synthesized DIDA with different diamines was carried out via Yamazaki’s phosphorylation method using triphenyl phosphite and pyridine system. The resulting poly(amide-imide)s were obtained in quantitative yields with inherent viscosities 0.36-0.47 dl/g in DMAc at 30 ± 0.1 °C. The poly(amide-imide)s were amorphous and were readily soluble in various solvents such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethylsulfoxide (DMSO), and pyridine. Tough and flexible films were obtained by casting their DMAc solution. According to thermogravimetric analysis, the polymers were fairly stable up to temperature around 396 °C, and 10% weight losses in the temperature range of 476-511 °C that showed good thermal stabilities of these polymers.