一种三相三线与三相四线自适应电能表的设计

针对合成孔径雷达（SAR）清晰成像的特点,为保证雷达天线波束指向稳定,设计了某型机载雷达天线稳定平台。为了消除雷达天线稳定平台控制中存在的非线性及不确定性因素的影响,提出了一种应用于雷达天线稳定平台控制系统的模糊PID控制策略。稳定平台是依据陀螺仪所采集载机的角速度,运用反向运动补偿的原理进行工作。控制策略中,在传统PID控制的基础上引入模糊控制算法,根据跟踪误差信号动态改变PID控制器参数,改善稳定平台的控制效果,完成稳定平台控制器的优化设计。仿真结果表明,优化后的模糊PID控制算法与传统PID控制算法比较,在稳定平台转速控制方面受到的外部干扰影响更小,响应速度更快。因此,基于模糊PID控制算法的雷达天线稳定平台具有更高的稳定性能。     

Multi-sensors SAR system for real-time dosimetry assessment

A multi-sensor test-bench for determining the SAR (specific absorption rate) due to wireless devices emitting in equivalent human tissues is presented. Real-time SAR assessment is proposed considering a spatially distributed multiprobe test-bench. In comparison with a multi-axial robot SAR system, the proposed one does not require any displacement, thus reducing drastically acquisition time, once parallel data acquisition and interpolation techniques are employed for accelerating measurements.     

基于哈特曼波前探测层析重建折射率场

介绍了哈特曼层析测量系统的原理,设计静态测试实验,对实际圆对称折射率场分布进行了层析重建.系统由哈特曼采集折射率场的投影数据,采用代数重建算法进行层析重建,取得了满意的重建结果.     

Study of the influence of the laterality of mobile phone use on the SAR induced in two head models

The objective of this paper is to investigate and to analyse the influence of the laterality of mobile phone use on the exposure of the brain to radio-frequencies (RF) and electromagnetic fields (EMF) from different mobile phone models using the finite-difference time-domain (FDTD) method.The study focuses on the comparison of the specific absorption rate (SAR) induced on the right and left sides of two numerical adult and child head models. The heads are exposed by both phone models operating in GSM frequency bands for both ipsilateral and contralateral configurations. A slight SAR difference between the two sides of the heads is noted. The results show that the variation between the left and the right sides is more important at 1800 MHz for an ipsilateral use. Indeed, at this frequency, the variation can even reach 20% for the SAR10g and the SAR1g induced in the head and in the brain, respectively. Moreover, the average SAR induced by the mobile phone in the half hemisphere of the brain in ipsilateral exposure is higher than in contralateral exposure. Owing to the superficial character of energy deposition at 1800 MHz, this difference in the SAR induced for the ipsilateral and contralateral usages is more significant at 1800 MHz than at 900 MHz. The results have shown that depending on the phantom head models, the SAR distribution in the brain can vary because of differences in anatomical proportions and in the geometry of the head models. The induced SAR in child head and in sub-regions of the brain is significantly higher (up to 30%) compared to the adult head.This paper confirms also that the shape/design of the mobile and the location of the antenna can have a large influence at high frequency on the exposure of the brain, particularly on the SAR distribution and on the distinguished brain regions.     

合成孔径雷达光学处理器的检测方法

本文以一个通用合成孔径雷达光学处理器(简称OSARP)的检测为例,来说明OSARP的检测方法。给出OSARP的每个可调部件与合成孔径雷达(简称SAR)数据片的各特征参数间的关系,通过测量调整量求得OSARP的适用范围;用普通检测目标加位移透镜,来检测OSARP的成像质量。同时用模拟的SAR数据片,以另一种方法对OSARP做检测,结果相同。最后处理了真实SAR数据片,用来展示SAR和OSARP的综合成像质量。文中给出一些实验照片和数据,结果表明,本检测方法是可行的。     

改进的双曲等效法用于双站合成孔径雷达前视成像

双站合成孔径雷达(SAR)前视成像有着很多的潜在应用,比如在能见度很低的天气实现飞机的导航和盲降,提高飞机飞行的安全度等.然而实现双站SAR前视成像的难点在于其距离历程的双根式性,直接采用驻定相位原理对其分解将得到复杂的解析式,从而后续算法的推导变得困难.现有的双曲等效法可以将双根式距离历程等效为单根式,但由于该方法为距离历程的二阶近似,当用于双站SAR前视成像时,由于其较大的前视角,未完全等效的距离历程高次项造成的误差已经超出可以接受的范围.针对以上问题,本文首先提出了一种改进的双曲等效法,该方法通过引入新的补偿变量来提高距离历程的等效精度;然后在此基础上推导回波信号的二维频谱解析式,并给出了一种适用于双站SAR前视成像的距离多普勒算法;最后通过仿真实验,将原双曲等效法与改进方法的等效误差以及成像结果做对比,验证了本文算法的有效性和优越性.     

Tomographic observation of shallow-water inhomogeneities in the case of probing by a focused high-frequency acoustic field. I. Structure of simulation model

We study the possibilities of acoustic tomography observation of small-size bodies in shallow-water layered oceanic waveguides within the framework of geometric acoustics. For increasing the spatial resolution and sensitivity in the considered inverse problem, we used the waveguide-matched focusing of the received and radiated fields into the region of expected location of the observed body. The algorithm of observation in this case consists of search for a global extremum of decision statistics, which is determined by the difference between the measured data and the hypothetic body location. Such hypotheses are formed on the basis of a priori information in the form of the waveguide model and the data on the structure of the observation system. For decreasing the influence of noise associated with the interference of fields in the waveguide, selection of separate tomographic ray projections with the subsequent incoherent accumulation of partial images is used. A tomographic shallow-water observation model based on such principles is analyzed. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 52, No. 2, pp. 134–150, February 2009.     

基于FPGA的DBF多波束中频接收系统的设计与实现

数字波束形成(DBF)阵列能够充分利用阵列天线所获取的空间信息,通过信号处理技术使波束获得超分辨率和低旁瓣的性能,它由天线阵元、射频下变频模块、AD采样、中频接收系统及上位机控制器组成。对中频接收系统进行数字波束形成的具体方案进行讨论,对多路接收和AD量化一致性造成的各通道间失配提出了幅相校正的解决方案,详细分析了研制中的关键技术。实验结果表明所设计的DBF多波束中频接收系统可有效实现通道间失配的校正,并实现精确的波束赋形功能。     

C波段机载合成孔径雷达海面风场反演新方法

针对基于散射计地球物理模型函数的机载合成孔径雷达(SAR)海面风场反演中存在的风向获取依赖于图像风条纹或数值预报、 散射计数据和浮标等背景场资料, 风向与SAR图像时空分辨率不匹配, 进而影响机载SAR海面风场反演精度等问题, 本文根据机载SAR对海探测特点, 研究一种适用于C波段机载SAR的海面风场反演新方法. 利用SAR图像距离向不同入射角的后向散射系数, 依据地球物理模型构造最小代价函数, 通过代价函数的求解直接从机载SAR数据同时反演出海面风速和风向. 利用论文提出的海面风场反演方法分别对仿真SAR数据和实测C波段机载SAR数据进行风向、 风速的反演误差分析及试验验证.研究结果表明, 该方法适用于机载SAR海面风场反演, 可不依赖背景风向直接反演出精度较高的风速和风向; 雷达后向散射系数误差是决定海面风速、风向反演精度的关键因素, 辐射定标精度越高则反演误差越小; 海面风速反演误差随着风速的提高而增大, 当海面风速大于18 m/s时, 风速反演误差显著增加, 而海面风向的反演误差与风速无明显关系. 关键词： 机载合成孔径雷达 海面风场 多入射角     

折射率渐变透镜的数值设计

传统折射率渐变透镜的设计要求初级馈源天线具有稳定的相位中心,这就限制了透镜的应用范围。为拓宽透镜的应用范围,提出了一种折射率渐变透镜的数值设计方法,通过对馈源天线的极化电场离散采样获得相位信息,并据此设计透镜,随后用金属短线结构的新型人工电磁材料来实现这种透镜。这种设计方法简单灵活,对馈源天线没有限制。以经典矩形贴片天线为例,比较了贴片天线和透镜天线的回波损耗和远场方向图,结果表明运用这种方法设计的透镜使贴片天线的增益提高了2 dB,口径效率从62%提高到了99%。     

制作工艺误差对X射线组合折射透镜聚焦性能影响研究

本文主要介绍对X射线组合折射透镜的制作工艺误差对其聚焦性能影响的研究结果. 首先给出采用深度X射线光刻技术制作的PMMA材料圆柱面型X组合折射透镜的工艺测试结果,得出制作工艺误差值,定性分析制作工艺误差对X射线组合折射透镜聚焦性能的影响. 然后根据实际的制作工艺误差建模,给出详尽的理论分析和定量的理论模拟结果. 最后在北京同步辐射装置(BSRF)上,构建基于PMMA材料的圆柱面型X射线组合折射透镜的微束聚焦实验系统,实际测试了有明显工艺误差和尽量消除工艺误差的两种X射线组合折射透镜的聚焦性能,给出实测结果 关键词： X射线组合折射透镜 制作工艺误差 X射线聚焦性能 同步辐射     

基于子带补偿的弹载聚束SAR成像算法

弹载SAR成像常用非线性变标类算法改善聚焦效果.然而,非线性变标算法由于自身的局限性,在三维匀加速聚束SAR成像模式中非常容易失效.针对这一问题,本文提出了一种子带补偿法,并将该方法结合到弹载SAR聚束成像算法中.新算法不引入三次相位操作,可有效补偿随目标位置走动的多普勒调频率.仿真结果和分析表明,与常用的非线性变标类算法相比,本文所提算法在运算量、成像结果、适用性上都具有优越性,具有一定的工程应用价值和理论意义.     

超低折射率特异材料天线

采用金属网格和泡沫材料实现低折射率材料媒质,并对其参数进行了优化,辐射源采用单极天线,制作了样机。利用HFSS电磁仿真软件对应用低折射率材料媒质天线与传统天线的方向性进行了对比研究,并研究了辐射源的参数对定向天线的性能影响。对样机进行了测试,测试结果与仿真结果比较吻合,与传统天线相比较,基于超低折射率特异材料的天线方向性明显提高。因此,选择适当电磁参数的超低折射率特异材料,用于定向天线的设计,可以改变传统天线的设计。     

A complex target terrain SAR raw data generation and evaluation based on inversed equalized hybrid-domain algorithm processing

In this paper, synthetic aperture radar raw data generation of complex target terrain based on inverse equalized hybrid-domain processing technique is proposed. Firstly, the basic synthetic aperture radar (SAR) echo model is derived via spectral analysis of extended chirp scaling. Then, the inverse equalized extended chirp scaling algorithm (ECSA) procedure is applied directly step by step to a real input SAR image in order to generate the raw data of the reference SAR image. The whole raw data generation (RDG) procedure only consists of Inverse Equalized ECSA (IEECSA) without integral equation and computation complexity, which means easier implementation and higher efficiency. By applying the resulted RDG into different image formation algorithms (IFAs), not only the final images are reconstructed but also the resulted RDG is evaluated in practice. Finally, valid image quality assessment techniques are implemented on the reconstructed images. The simulations not only confirm the validity of the proposed RDG method based on inverse equalized hybrid-domain technique but also evaluate the quality metrics of reconstructed images as a method of reliability assurance.     

Focusing of singular beams

The process of focusing of an inhomogeneously polarized beam passed through a system consisting of a uniaxial crystal and a polarization filter is considered. It is shown that the action of this system is equivalent to the action of a phase transparency with a complex relief of the refractive index. In particular, if the angle between the axes of the quarter-wave plate and the polarizer is equal to 45°, this transparency has a helicoidal relief. Simultaneously, two singular beams with different curvatures of their wavefronts arise in the transparency. The action of the lens consists in formation of a combined singular beam having three focal waists. The boundary wave arising upon focusing is able not only to form a new spectrum of toroidal vortices, but also to straighten the focusing region, forming a fairly extended range with a weak divergence.     

基于小波的多极化机载合成孔径雷达海面风向反演

为了实现从合成孔径雷达(SAR)图像本身提取高精度的海面风向信息, 提高SAR海面风场反演精度,研究了多极化机载SAR海面风向反演技术, 借助小波分析相对傅里叶分析和局部梯度更精细的时-频分析能力, 将二维连续小波变换与快速傅里叶变换(FFT)相结合,提出一种新的机载SAR海面风向反演方法. 为验证反演方法的有效性,通过海上同步飞行试验获取多极化机载SAR数据及同步调查船实测风向数据,用于反演试验的数据比对.采用本文提出的方法, 利用多种小波基对机载C波段SAR的同极化和交叉极化数据进行风向反演, 将反演结果与美国国家环境预报中心再分析资料以及调查船实测风向进行比对. 结果表明,本文提出的基于小波分析的海面风向反演方法适用于机载SAR探测数据, 反演精度优于二维FFT法和局部梯度方法;小波基的选择对反演结果影响较大, Mexican-Hat小波基是机载SAR海面风向反演的最优小波基, 且同极化与交叉极化机载SAR数据均可用于海面风向的反演.     

连续模式相干测风激光雷达性能优化分析及实验研究

基于风场探测的需求,采用1550 nm波长连续激光种子源搭建了一套全光纤结构多普勒相干测风雷达系统.从雷达方程出发,对连续激光相干雷达载噪比方程和不同雷达收发望远镜聚焦位置下风速合成权重进行了分析.针对测风雷达要求设计了5～200 m的变焦激光收发望远镜模块.扩束系统采用伽利略折射式结构,发射光束准直下扩束比为23,光...     

Design of a Quasi-Optical System to Convert TE0n Mode Outputs of a Gyrotron into Gaussian Beams

In this paper we present a novel design of a quasi-optical system for conversion of gyrotron outputs into gaussian beams. It consists of a quasi-optical antenna, four focusing mirrors (parabolic cylinders) and a filter which removes the side lobes of the beam. The system is capable to convert three TE_0n mode outputs into gaussian beams with waist size of 16.7 mm as well as four TE_1n mode outputs into bi-gaussian beams with waist size of 10.9 mm in width and 16.5 mm in length.     

Graphene nanoribbon based terahertz antenna on polyimide substrate

Graphene nano ribbon based terahertz patch antenna on polyimide substrate is designed and its radiation characteristics are investigated in the 725–775 GHz band. The terahertz communication system consists of higher data rate transmission, low transmit power with secured wireless communication. The proposed antenna consists of graphene nano ribbon as radiating patch and also the ground plane separated by a 20 μm thin polyimide substrate. The antenna has achieved the broad impedance bandwidth (>5%) in the band of operation. The design has yielded a peak gain of 5.71dB at 750 GHz. The antenna is simulated by using the finite element method based simulator Ansys - HFSS.     

Optical diffraction tomography microscopy with transport of intensity equation using a light-emitting diode array

Optical diffraction tomography (ODT) is an effective label-free technique for quantitatively refractive index imaging, which enables long-term monitoring of the internal three-dimensional (3D) structures and molecular composition of biological cells with minimal perturbation. However, existing optical tomographic methods generally rely on interferometric configuration for phase measurement and sophisticated mechanical systems for sample rotation or beam scanning. Thereby, the measurement is suspect to phase error coming from the coherent speckle, environmental vibrations, and mechanical error during data acquisition process. To overcome these limitations, we present a new ODT technique based on non-interferometric phase retrieval and programmable illumination emitting from a light-emitting diode (LED) array. The experimental system is built based on a traditional bright field microscope, with the light source replaced by a programmable LED array, which provides angle-variable quasi-monochromatic illumination with an angular coverage of ±37 degrees in both x and y directions (corresponding to an illumination numerical aperture of ∼0.6). Transport of intensity equation (TIE) is utilized to recover the phase at different illumination angles, and the refractive index distribution is reconstructed based on the ODT framework under first Rytov approximation. The missing-cone problem in ODT is addressed by using the iterative non-negative constraint algorithm, and the misalignment of the LED array is further numerically corrected to improve the accuracy of refractive index quantification. Experiments on polystyrene beads and thick biological specimens show that the proposed approach allows accurate refractive index reconstruction while greatly reduced the system complexity and environmental sensitivity compared to conventional interferometric ODT approaches.