合成高产率分子筛MCM-48

以十六烷基三甲基溴化铵（CTAB）和Triton X-100（TX-100）混合表面活性剂为模板剂,正硅酸乙酯（TEOS）为硅源,采用水热法合成了MCM-48分子筛.实验中发现,晶化3 d后用醋酸调节溶液pH值的方法可有效提高MCM-48分子筛的产率；同时采用混合表面活性剂使模板剂的利用效率达到了6.0 TEOS/1.0 Surf (摩尔比）,并通过XRD、N2-吸附/脱附和TG-DSC等测试手段对产物的结构性能进行了表征.     

低温下MCM-48的高产量合成

通过调节合成温度(303~313 K)和共模板剂, 在较低的温度下快捷、方便、高产率(98%)地合成了MCM-48, 并对产物进行了粉末X射线衍射、N2吸附-脱附、透射电镜(TEM)和扫描电镜(SEM)等结构表征.     

含氟体系中合成高品质的MCM-48介孔分子筛

在含氟体系中以正硅酸乙酯和十六烷基溴化铵作为硅源和模板剂,合成高质量的MCM-48。主要考察了各种影响合成MCM-48的因素,得到的产物分别用XRD,TEM和N₂吸附-脱附技术进行表征。结果表明,合成高质量MCM-48的条件是温度为393 K,时间为24 h,CTAB/Si比为0.65;得到的MCM-48具有较大的比表面积(130 5 m²/g),孔径分布比较集中(2.416 nm)。     

混合表面活性剂与调节pH值法高效合成MCM-48

以正硅酸乙酯（TEOS）为硅源、十六烷基三甲基溴化铵（CTAB）与曲拉通X- 100(TX-100)热合成中孔MCM-48．在合成过程中通过调节溶液pH值可有效提高MCM- 48的收率和水热稳定性，同时采用剂使模板剂的利用效率达到了6.0TEPOS／1.0 Surf．并通过XRD、N_2-吸附／脱附和FT-IR等测试手段对产物进行了表征.     

以混合表面活性剂为模板可控合成MCM-48和MCM-41分子筛

利用阳离子和三嵌段共聚物混合表面活性剂为模板,在水热条件、碱性介质中可控合成出MCM-48和MCM-41分子筛。在固定P123(聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物):TEOS(正硅酸乙酯)(物质的量的比)为0.01875的体系中,调节CTAB(十六烷基三甲基溴化铵)∶TEOS(正硅酸乙酯)物质的量比值m,当m在0.12~0.13范围合成出MCM-48分子筛;当m在0.04~0.08范围合成出MCM-41分子筛。通过XRD,TEM,N2物理吸附,IR等方法进行了表征。结果表明:聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(P123)的加入可以更大程度地降低合成介孔材料所需阳离子表面活性剂的用量;可控合成的介孔材料具有高比表面积、高度有序的孔道结构、较集中的孔径分布。     

KNO3/MCM-48催化酯交换法合成碳酸二丙酯

 对KNO3/MCM-48用于丙醇和碳酸二甲酯进行酯交换合成碳酸二丙酯的催化性能进行了考察. 用X射线衍射(XRD)、红外光谱(IR)和X射线荧光法研究了催化剂的结构特征和表面性质. XRD结果表明,随着K负载量的增加,载体特征峰强度逐渐减弱,但仍保留MCM-48的晶体结构. 随着焙烧温度的升高, KNO3逐渐分解成K2O. 分别考察了活性组分负载量、焙烧温度、焙烧时间和催化剂的用量以及反应时间对反应的影响. 结果表明, KNO3/MCM-48催化剂对碳酸二丙酯的合成具有很高的催化活性. 在反应温度363 K, 反应时间6 h, 催化剂用量5%, 丙醇与碳酸二甲酯摩尔比为4的条件下,碳酸二甲酯的转化率可达99.9%, 产物碳酸二丙酯选择性93.4%, 产率93.3%.     

基于MCM-41微反应器的微波辅助合成新方法研究

采用微波辐射合成法合成了纳米介孔分子筛MCM-41作为微反应器.以苯并呋喃-2(3H)-酮的合成为实例,在甲苯介质中将邻羟基苯乙酸组装到MCM-41微反应器中,研究了溶液体系及微反应器中反应温度、反应时间及微波辐射时间对反应的影响.结果显示,在施加微波与不施加微波情况下,MCM-41微反应器中进行的反应较溶液体系中进行的反应产率提高了2～33与2～12倍.对于MCM-41微反应器中的反应,施加微波辐射后反应产率可进一步提高20%～100%.     

嫁接Al改性MCM-41介孔分子筛催化合成双酚F

以十六烷基三甲基溴化铵和正硅酸乙酯为原料,合成纯硅MCM-41介孔分子筛。再利用九水硝酸铝为改性剂来嫁接改性纯硅MCM-41介孔分子筛,NH3-TPD结果表明,嫁接后的AlMCM-41产生了中强酸。用改性后不同n(Si)/n(Al)的AlMCM-41催化合成双酚F,在n(苯酚)/n(甲醛)=30、反应时间5 h、反应温度90℃、m(甲醛)/m(AlMCM-41)=7的反应条件下,在一定范围内,双酚F的产率随Al含量增加而增加,但在n(Si)/n(Al)50时,双酚F的产率反而下降,当n(Si)/n(Al)=50时,双酚F的产率最高,为42.28%。     

介孔Ce-MCM-48的合成及其可见光催化性能研究

分别利用十六烷基三甲基溴化铵(CTAB)、正硅酸乙酯(TEOS)为模板剂和硅源,合成了高度有序的MCM-48材料。通过浸渍法制备了Ce含量不同的MCM-48(Ce-MCM-48s)材料。采用TG-DTA、小角XRD、N2吸-脱附、FT-IR、TEM、XPS和UV-vis等对Ce-MCM-48s进行了表征。XRD、N2吸-脱附和TEM证明Ce-MCM-48s具有与MCM-48相似的三维螺旋立体结构;FT-IR和XPS表明MCM-48孔道及其表面已被Ce氧化物所覆盖。可见光催化降解罗丹明B的实验证明,10%Ce-MCM-48的催化降解效率好于纯CeO2,商用TiO2(P125),5%Ce-MCM-48和15%Ce-MCM-48的。     

膨胀剂用量、合成体系pH值和MCM-22（P）的硅／铝比对ITQ-2分子筛合成的影响

考察了膨胀剂的用量、合成体系的pH值和MCM-22(P)的硅/铝比对合成ITQ-2分子筛的影响. 结果表明,同时降低膨胀剂十六烷基三甲基溴化铵和四丙基氢氧化铵的用量,在pH=11.5时 4 h 即可完成对MCM-22(P)的插层膨胀;pH值降低时,可减小由于脱硅对ITQ-2分子筛硅/铝比下降的影响,并且使产物收率大幅度提高. 同时, pH值降低使后续的超声剥离更加容易,且可避免生成MCM-41介孔分子筛杂相. MCM-22(P)的硅/铝比越大,层表面的电荷密度越低,带负电荷的层板和阳离子插层剂之间的静电引力和分子间作用力也就越小,致使插层膨胀和随后的超声剥离越容易.     

Surface modification to improve the sorption property of U(VI) on mesoporous silica

Polyoxometalates K₇[α-PW₁₁O₃₉]·14H₂O (PW11) modified mesoporous silica (MCM-48) with cubic structure, was prepared by impregnation and calcination methods. The modified mesoporous silica sorbent (PW11/MCM-48) was studied as a potential adsorbent for U(VI) from aqueous solutions. MCM-48 and PW11/MCM-48 were confirmed by X-ray diffraction and nitrogen physisorption techniques. The results indicate the original keggin structure of PW11 and mesoporous structure of MCM-48 are maintained after supporting PW11 on mesoporous silica MCM-48. The effects of contact time, solid-to-liquid ratio (m/V), solution pH and ionic strength on U(VI) sorption behaviors of the pure and modified mesoporous silicas were also studied. Typical sorption isotherms such as Langmuir and Freundlich isotherms were determined for sorption process. The results suggest that the sorption of U(VI) on MCM-48 or PW11/MCM-48 are strongly dependent on pH values but independent of ionic strength. The sorption capacity of PW11/MCM-48 for U(VI) is about ten times more than that of MCM-48.     

Study on sorption of U(VI) onto ordered mesoporous silicas

The mesoporous silicas (MCM-41 and MCM-48) are synthesized by hydrothermal method, which are characterized by XRD and BET techniques. The application of mesoporous silicas for the sorption of U(VI) from aqueous solution are studied by using batch technique under ambient condition. The effects of contact time, solid-to-liquid ratio (m/V), solution pH, ionic strength and temperature are determined, and the results indicate that the sorption of U(VI) to MCM-41 or MCM-48 are strongly dependent on pH values but independent of ionic strength. Compared with Langmuir model, the sorption isotherms can be simulated by Freundlich model well according to the high relative coefficients. The parameters for Langmuir and Freundlich sorption isotherms are calculated from the temperature at 298, 318 and 338 K, respectively, and the results suggest that the sorption of U(VI) on MCM-41 or MCM-48 is a spontaneous and exothermic process. In contrast to its sorption capacity for U(VI), MCM-48 is a suitable material for the preconcentration of U(VI) from large volumes of aqueous solutions.     

MCM-48介孔分子筛的高压合成

采用正硅酸乙酯（TEOS）作硅源,十六烷基三甲基溴化铵（CTAB）为模板剂,在高压 （约7 MPa）和373 K下合成了MCM-48介孔分子筛.用XRD、氮气吸附及29Si MAS NMR对样品 进行了表征.与常压合成的相比,高压下合成的MCM-48具有更高的热稳定性和水热稳定性.2 9Si MAS NMR结果表明,高压有利于分子筛孔壁的聚合,导致分子筛结构更加完善,从而使 其具有更高的稳定性.     

Caffeine loading into micro- and nanoparticles of mesoporous silicate materials: in vitro release kinetics

Caffeine was loaded into microparticles and nanoparticles of MCM-41 and MCM-48 to study its release into simulated body fluid at pH 7.4 and 37°C. The silicate systems were characterized by X-Rar Diffraction (XRD), scanning electron microscopy, and nitrogen adsorption/desorption isotherms. Loading of caffeine was confirmed by thermal gravimetric analysis and FTIR and the loading capacity was determined by high performance liquid chromatography (HPLC). The loading capacities for the microparticles are higher than that for the nanoparticles for both silicate systems, with the highest (56.8%) for the microparticles of MCM-48. However, for each system, the release from nanoparticle is faster than from microparticles. For all systems, diffusion is the major dissolution mechanism.     

Ce-MCM-48介孔分子筛的合成、表征和催化性能

Cerium incorporated MCM-48 molecular sieves have been hydrothermally synthesized by both a mixed template and a variable pH approach. The samples were characterized by various physicochemical methods, including X-ray diffraction, transmission electron microscopy, diffuse reflectance UV-vis spectroscopy, XRF spectroscopy, nitrogen adsorption. These results reveal that cerium is incorporated in MCM-48 in the form of well-dispersed tetra-coodinated cerium ion. Maintaining the proper concentration of cerium and adjusting the pH allows for a more ordered structure with a much higher specific surface area than that of MCM-48. Ce-MCM-48 was employed in the liquid phase oxidation of cyclohexane with aqueous H2O2. The results showed that Ce-MCM-48 is more active as a catalyst for the liquid phase oxidation of cyclohexane. The oxidation conversion catalyzed by Ce-MCM-48 is 8.3 %-14.2% higher than that catalyzed by MCM-48 and the selectivity for the main products increase by 63.4%-68.8%. Accordingly, Ce-MCM-48 has been shown to have important potential applications.     

Synthesis of hydrothermally stable and long-range ordered Ce-MCM-48 and Fe-MCM-48 materials

The hydrothermally stable and long-range ordered Ce-MCM-48 and Fe-MCM-48 were conveniently synthesized at 393 K for 24 h by directly adding fluoride ions to the initial gel without posttreatment and pH adjustment. The Ce-MCM-48 with a Si/Ce of 200 and 100, which were prepared by directly adding fluoride ions, could still maintain their mesoporous structures after refluxing in boiling water for 3 days. The incorporation of Ce into MCM-48 could enhance the hydrothermal stability of MCM-48 in the absence of fluoride ions; however, the incorporation of Fe into MCM-48 materials barely improved the hydrothermal stability of MCM-48 materials. The effect of adding NaF was much more efficient in enhancement of hydrothermal stability than that of the incorporation of Ce. The addition of fluoride ions mainly improves the degree of polymerization of silicates. The Ce(4+) ions in Ce-MCM-48 appear to be present partly in tetrahedral coordination in the framework and partly as CeO(2) particles on the surface of framework. The Ce positioned on the surface of pore walls and in the framework both provide the protection against water attack.