光纤原料四氯化硅中微量三氯氢硅的气相色谱分析

采用石英毛细管柱与氩检测器相联结的气相色谱方法定量检测高纯的光纤原料四氯化硅中微量三氯氢硅等含氢杂质。该方法简单、可靠,三氯氢硅的检测下限达０．１×１０￣（－６）Ｗ／Ｗ。     

Comparison of cryoscopic determinations of purity of benzene by thermometric and calorimetric procedures

Workers at the National Bureau of Standards and elsewhere have been conscious of the discordant results sometimes yielded by two methods for determining purity employing the same physical principle. A comparison was made on samples of benzene by the thermometeric method, by which a stirred sample is frozen at nearly constant rate, and by the calorimetric method, by which a frozen sample is melted in stages by the addition of accurately controlled increments of energy under adiabatic conditions.Benzene, purified by single crystal formation and of very high purity, was contaminated in known amounts by n-heptane and samples of the same level of purity determined by both procedures. Great care was taken to submit samples of the same composition to the different groups employing the two different methods. Further, the actual degree of contamination of the benzene was unknown to both groups until final values of the purity were submitted. Results of this comparison showed that the large divergence between the two methods that had characterized earlier comparisons is not displayed. The differences between the analyses on all three samples are roughly of the order of the statistically estimated uncertainties of the averages and less than deviations between individual experiments by one method. Comparison of the methods with absolute values of purity could not be made because of contamination of the highly purified sample of benzene with supposedly chemically adsorbed water from the borosilicate glass walls.     

Determination of dieldrin in wool products by gas chromatography with microwave-assisted extraction

Dieldrin is a moth-proofing agent that was banned by the Stockholm Convention in 2001. The amount of dieldrin in wool products was measured by a microwave-assisted extraction (MAE) method. The optimal conditions were as follows: extraction solvent, acetone/n-hexane (1:1 v/v); extraction temperature, 110 degrees C; extraction time, 10 min; solvent volume, 25 mL. When six samples were used, dieldrin contents determined by GC with the proposed MAE agreed closely with those by the Japanese official method using GC with solvent extraction and cleanup by column chromatography. The proposed MAE has two merits. First, the pretreatment of the MAE needs only 4 h for 11 samples, while that using the Japanese official method needs 2 days for six samples. Second, the volume of organic solvents used for the proposed method was only about one-tenth of that used in the Japanese official method. Our proposed method seems to be easy and useful for daily (routine) tests. Dieldrin contents of 28 used wool products, which were obtained from local clothing shops and ordinary homes, were determined by GC with the proposed MAE, and six products contained dieldrin (0.310-175 ppm). The dry cleaning of the woolen yarn containing 175 ppm dieldrin did not remove a significant amount of dieldrin. Therefore, it seems likely that dieldrin is still distributed slightly but widely throughout the world.     

Gas chromatographic determination of 1,4-dioxane at low parts-per-million levels in glycols

1,4-Dioxane is a flammable liquid and tends to form explosive peroxides. Its formation in glycols (low parts-per-million levels), which are used as dehumidifying agents in refineries, may take place by condensation. 1,4-Dioxane thus formed gets distilled over with benzene in the refinery process. Therefore, it is necessary to identify and determine the levels of 1,4-dioxane in glycols as well as benzene. Gas chromatography (GC) is probably the best technique for this purpose. GC analysis may be carried out using a flame ionization detector. Results show that 1,4-dioxane can be comfortably determined down to 2 ppm in glycols and benzene.     

Isolation of ATP from a yeast fermentation broth using a cryogel column at high flow velocities

This communication presents an effective method for isolating adenosine triphosphate (ATP) from a yeast fermentation broth using an anion‐exchange supermacroporous cryogel column at high flow velocities. The breakthrough and elution behaviors of pure ATP in the cryogel bed were investigated at flow velocities of 2, 5, and 10 cm/min and the ATP binding capacities were determined. Then the ATP‐containing yeast fermentation broth was employed as the test feedstock and various chromatographic runs were conducted to isolate ATP by the cryogel at different high flow velocities. The ATP samples obtained were analyzed quantitatively by HPLC. The results showed that even at a flow velocity of 5 or 10 cm/min, a product purity of 97.4 or 98.0% can be achieved, illustrating the potential of the present method for separation of high‐purity ATP directly from fermentation feedstock at high flow velocities.     

Fast Determination of Monocyclic Aromatic Hydrocarbons in Ambient Air Using a Portable Gas Chromatography–Photoionization Detector

Many air sampling methods are time consuming and require complex pre-treatment steps. Gas chromatography–photoionization detector (GC–PID) is a rapid method for sampling and analysis. However, although it has been used in a number of studies, its operating conditions and performance parameters have not been optimized systematically. In this study, a GC–PID method for analysis of monocyclic aromatic hydrocarbons in gas samples without pre-concentration or enrichment was developed and optimized. This GC–PID can perform both online and off-line analysis. In online analysis, the sample was pumped directly into a Teflon sample loop (pumped online injection), which resulted in minimal loss of sample. The optimum parameters were as follows: 30-s pumping time, 10 mL min^?1 of carrier gas flow rate, and 40 °C oven temperature. GC–PID was applied to analysis of benzene, toluene and xylene. The calibration curves showed good linearity for online analysis. The results obtained by GC–PID were accurate and reliable, with all the correlation coefficients ≥0.9972 and all the relative standard deviations <3%. A mixture of benzene, toluene, and o-, m-, and p-xylenes was separated satisfactorily in 10 min, except for m- and p-xylene. The performance of the portable GC–PID was compared with that of an ATD–GC–FID for quantification of benzene, toluene and xylene in calibration gas samples, and benzene, toluene, ethylbenzene, and the o-, m-, and p-xylenes in outdoor ambient air. The results indicated that GC–PID with pumped online injection was stable and accurate for analysis of these monocyclic aromatic hydrocarbons.     

间二氯苯纯度的测定

通过测定间二氯苯中的杂质含量得到间二氯苯的纯度。分别采用高效液相色谱法(HPLC–UVD)和气相色谱法(GC–FID)测定间二氯苯中主要杂质邻、对二氯苯的含量,结果表明两种方法所得杂质含量一致;用高效液相色谱法(HPLC)测定间二氯苯中杂质苯的含量,卡尔费休(Karl Fischer)法测定水分含量,热重法(TGA)进行灰分测定,电感耦合等离子体质谱(ICP–MS)法测定无机杂质含量。最终确定间二氯苯的纯度为99.60%,扩展不确定度为0.03%(k=2)。该方法测定结果准确可靠,具有可溯源性。     

用于固相微萃取的乙烯基开链冠醚复合涂层的研制

固相微萃取 (SPME)是一种新型的样品预处理技术 [1] ,其核心是 SPME装置中萃取头上的固相涂层 .目前商用 SPME涂层的种类较少 ,热稳定性较差 (推荐使用温度 2 0 0～ 2 80℃ ) ,使用寿命较短(40～ 1 0 0次 ) ,价格偏高 ,限制了其推广应用 .因此发展高选择性、高稳定性和高效的固     

Analysis of low molecular weight hydrocarbons including 1,3-butadiene in engine exhaust gases using an aluminum oxide porous-layer open-tubular fused-silica column.

A method for the quantitative analysis of individual hydrocarbons in the C1-C8 range emitted in engine exhaust gases is described. The procedure provides base-line or near base-line resolution of C4 components including 1,3-butadiene. With a run time of less than 50 min, the light aromatics (benzene, toluene, ethyl benzene, p- and m-xylene, and o-xylene) are resolved during the same analysis as aliphatic hydrocarbons in the C1-C8 range. It is shown that typical 1,3-butadiene levels in engine exhaust are about 5 ppm at each of two engine conditions. Aromatic hydrocarbon levels show a dependence on engine operating conditions, benzene being about 20 ppm at high speed and about 40 ppm at idle.     

多种方法分析与评价乙酸乙酯合成实验中产物之纯度

采用气相色谱内标法、面积归一化法及NMR内标法3种方法对乙酸乙酯合成反应中的产物进行纯度分析.GC内标法可抵消由于操作条件的波动而带来的误差,只需内标物与待测组分在同样条件下出峰且分离度较好,定量精度高,测出的乙酸乙酯纯度最低;应用NMR内标法可同步完成纯度分析和结构鉴定,且无需引入校正因子,操作简便.     

二甲硫基甲苯二胺的合成与表征

在聚氨酯弹性体的加工成型中必须加入一种兼起扩链和交联作用的固化剂 ,几十年来使用得最为成功的固化剂当属 3 ,3′ 二氯 4,4′ 二氨基 二苯基甲烷 (MOCA)。虽然用MOCA制得的弹性体的物理力学性能最好 ,而致命的弱点是致癌性 ,美国政府已命令终止MOCA在聚氨酯中的应用[1 ] 。为此世界各国竞相研究新型固化剂[2 ] ,但均未获理想的结果。1 987年 ,美国Ethyl公司研究发现二甲硫基甲苯二胺 (DMTDA)是一种有希望取代MOCA的固化剂[3] ,但其固化性能均不及MOCA。DMTDA的合成最早是用路易斯酸作为催化剂 ,反应温度范围为 2 0～ 3 0 0…     

Sensitive and rapid determination of elemental nanosulfur/sulfur by liquid chromatography

In order to identify the most suitable method for the estimation of nanosulfur for studying its residue dynamics, the present work was taken up. HPLC and GC methods were explored for its analysis. A comparative study of the existing analytical methods for the quality control of nanosulfur was undertaken. UV spectrophotometry and HPLC methods were superior with lower LOD when compared to GC–MS, which was not satisfactory due to breakage of catenated S₂₀ into S₆ and S₈. The method has been validated by analyzing various nanosulfur formulations of known concentrations. The recovery of the UV and HPLC methods ranged from 80.71 to 109.51% and 82.31 to 109.84%, respectively. The LOD of UV, GC–MS, and HPLC is 4, 20, and 1 ppm, respectively. The retention time of sulfur was 13.77 (HPLC), 2.89 (ultra high performance liquid chromatography), and 12.715 + 21.524 min (GC–MS). The method was successfully utilized for estimating sulfur in natural samples such as water from a sulfur hot spring and wastewater. The method has been validated by following the method recommended by the American Society for Testing and Materials. The HPLC method emerged as the best analytical method for the estimation of elemental sulfur.     

Homogeneity studies of powders and plasma sprayed deposits

For production of plasma sprayed protective deposits and self-standing ceramic parts many different feedstock powders are used. The powders are very often of a composite type prepared by various technologies and mostly chemically very inhomogeneous. A method has been developed for evaluation of chemical homogeneity of both, the feedstock powders and the sprayed materials. The backscattered electron images along with the element mapping of dopant have been used as the basic measurement. The homogeneity coefficients were determined by quantitative point analysis with ZAF corrections. The results show that under all spraying parameters there is always a certain redistribution of all species leading to a better homogeneity. But generally, the more homogeneous the feedstock powder, the better the homogeneity of the deposits on both micro and macro scale.     

气相色谱-单光子电离飞行时间质谱的联用及在柴油组分表征中的应用

建立了一种气相色谱(GC)与单光子电离-飞行时间质谱(SPI-TOF MS)联用(GC/SPI-TOF MS)的分析方法。首先,设计了一种双层套管的传输管用于连接GC与SPI-TOF MS,实现了GC与单光子电离离子源的无缝连接。在此基础上,以n-十五烷标准品和苯/甲苯/二甲苯的标准气为对象,对电离源的重要电压参数进行了优化,得到了纯净的分子离子峰,实现了对各类有机物的快速和准确定性。最后,将该方法用于分析柴油中的挥发性与半挥发性有机物,获得了柴油组分的二维GC×SPI-TOF MS谱图。不需要复杂的谱图解析和数据处理,根据谱图中离子的质荷比(m/z)归纳了柴油的主要成分,包括脂肪烃、芳香烃和含量很低的苯并吡咯等含氮化合物;根据色谱的保留时间将柴油中的同分异构体区分开来。结果表明GC/SPI-TOF MS法是一种简单、有效的分析方法,非常适于柴油及复杂环境样品等的分析表征。     

气相色谱法分离和测定溶剂型木器涂料中正丁醇与苯系物

在气相色谱法测定溶剂型木器涂料中正丁醇及苯系物(包括苯、甲苯及二甲苯)时采用了VF-200MS型号的毛细管色谱柱。由于此型号的毛细管柱具有较强极性,不仅能达到正丁醇与苯系物之间的有效而满意的分离,而且还能使苯系物(包括苯、甲苯、乙苯、二甲苯)之间和二甲苯的同分异构体之间的有效分离。测定中采用正戊烷作内标和用火焰离子检测器检测。此方法的检出限(2S/N)在1.7~3.5 ng之间。用一含有正丁醇的硝基漆样品按所提出的方法进行多次重复测定,并在此样品的基础上加入各被测化合物的标准后进行测定,从而对方法的回收率和精密度作了测试,测得其回收率在87.8%~100.0%之间,测定值的相对标准偏差(n=6)均小于2.5%。     

Determination of rare earth elements impurities in high purity uranium

A sensitive radiochemical procedure has been developed for the separation and determination of Dy, Sm, Gd, Eu, La and Lu in high purity uranium. The method is based on quantitative extraction of uranium using NPy/benzene as an extractant from 7M HCl solution. Rare earth elements (REE) remaining in the aqueous phase were subsequently determined by INAA.     

汽油中苯的测定

采用高分辨毛细管气相色谱对汽油中的苯进行测定。在汽油样品组分中选定一组分为内标,测定样品后再用内加法添加苯,再次测定,并以两次测定的峰面积数据计算苯量。本文在汽油辛烷值的测定基础上,发展了一种新的汽油中苯量的测定方法：采用国产色谱仪,带内标的内加法即可对汽油中的苯量进行准确测定．在不同标号的汽油测定实验中,相对标准偏差不超过3％。与国标方法相比,该方法简便快速,对仪器设备要求低,提高了分析效率,降低了分析成本,便于推广。     

Preparative separation of quinolines by centrifugal partition chromatography with gradient elution

Centrifugal partition chromatography has been successfully applied to the separation of 2-alkylquinolines from liquid combinatorial synthesis crude samples. Original gradient elution using the ternary two-phase solvent systems heptane-water-acetonitrile and heptane-acetonitrile-methanol were used to separate them with high purity degrees. Part of the effluent was monitored with evaporative light scattering detection, for direct control, and the collected fractions were analyzed by thin-layer chromatography, GC, nuclear magnetic resonance spectroscopy and MS. It was thus possible to purify in one run more than 3 g of crude mixture using only 1.31 of solvents to obtain more than 300 mg of several alkylquinolines homologues with 99% purity and in less than 7 h.     

气提吸附／热脱附／气相色谱－质谱法分析污水中的痕量有机物

采用气提吸附／热脱附／气相色谱－质谱法对齐鲁公司所处地区工业污水进行分析。方法采用Ｔｅｎａｘ－ＧＣ吸附剂对样品进行气提吸附，脱附时样品直接进入色谱仪汽化室，一次进样即可完成全组分分析，共检测出含四氯丙醚在内的４０种有机组分，测定了各组分的程序升温保留指数。气相色谱－质谱法测定出四氯丙醚三个异构体的结构。     

Quantitative evaluation of benzene, toluene, and xylene in the larvae of Drosophila melanogaster by solid-phase microextraction/gas chromatography/mass spectrometry for potential use in toxicological studies

A simple, rapid, and solvent-free method for quantitative determination of benzene, toluene, and Xylene in exposed Drosophila larvae was developed using headspace solid-phase microextraction (HS-SPME) coupled to GC/MS. Larvae fed on standard Drosophila food mixed with benzene, toluene, and Xylene for 48 h were homogenized in Milli-Q water. Extraction of benzene, toluene, and Xylene was performed at 65 degrees C for 30 min on the SPME fiber (silica-fused). Subsequently, the fiber was desorbed in the GC injection port, followed by GC/MS analysis in the selected-ion monitoring mode. An external calibration curve was used for the quantification of benzene, toluene, and Xylene in the exposed organism. Recoveries were in the range of 78-82% (intraday) and 76-81% (interday) in larvae, and 91-96% (intraday) and 87-92% (interday) in the diet. LOD with an S/N of 3:1 and LOQ with an S/N of 10:1 were in the range of 0.01-0.023 and 0.034-0.077 microg/L, respectively. Percent RSD values for benzene, toluene, and Xylene were in the range of 0.50-0.81 (intraday) and 0.89-1.23 (interday) for retention time, and 2.16--3.85 (intraday) and 2.99-4.95 (interday) for peak concentration, showing good repeatability. This method was sensitive enough to quantitate benzene, toluene, and Xylene in small exposed organisms like Drosophila larvae. The SPME/GC/MS method developed may have wider applications in various in vivo toxicological studies.