Water effect on the gelation behavior of polyacrylonitrile/dimethyl sulfoxide solution

The gelation behavior of polyacrylonitrile (PAN)/dimethyl sulfoxide (DMSO) solution containing different amounts of water has been investigated using various methods. The ternary phase diagram of PAN/DMSO/water system indicated that water enhanced the temperature at which phase separation of PAN/DMSO solution occurred. Intrinsic viscosities [η] of dilute PAN/DMSO solution and PAN/DMSO/water solution at varied temperatures were measured to examine the influence of water on the phase behavior of PAN/DMSO solution. The presence of water in the solution gave rise to elevated critical temperature T_c. The gelation temperature T_g obtained by measuring the loss tangent tan δ at different oscillation frequencies in a cooling process was found to increase with increased water content in the solution. The critical relaxation exponent n value, however, changed little with varied concentration. During the aging process, the gelation rate of PAN/DMSO solution increases with the water level. The n values of the PAN/DMSO solutions with 2 wt% and 4 wt% water were a little larger than that of the solution without water, which may be explained by the turbid gel resulted from phase separation. The n values obtained in the aging process were larger than those obtained in the cooling process for the same three solutions, ascribed to the weaker gel with less cross-linking points formed in long time. Water led to the formation of denser gel structure. The coarser gel surface can also be attributed to the phase separation promoted by water.     

Electrospun EGNPs reinforced precursor carbon nanofibril composites by using RSM

Response surface methodology (RSM),based on five‐level, four variable Box‐Benkhen technique was investigated for modeling the average fiber diameter of electrospun polyacrylonitrile (PAN) nanofibers. The four important electrospinning parameters were studied including applied voltage (kV), Berry's number, deposition distance from nozzle to collector (cm), and spinning angle (? in degree). The measured fiber diameters were in a good agreement with the predicted results by using RSM technique. High‐regression coefficient between the variables and the response (R² = 87.74%) indicates excellent evaluation of experimental data by second‐order polynomial regression model. The optimum PAN average fiber diameters of 208 and 37‐nm standard deviation were collected at 19 kV, Berry's number = 10, 25^° spinning angle, and 16‐cm deposition distance. The PAN/N,N‐dimethylformamide (DMF) polymer solution with the optimum weight concentration (10 wt.%) was selected to study the effect of dispersing exfoliated graphite nanoplatelets (EGNPs) in PAN/DMF solution on the electrospun EGNP/PAN fibril composite diameter. Five different EGNPs weight concentrations (2, 4, 6, 8, and 10 wt.%) were dispersed in the optimized PAN/DMF polymer solution. Morphology of EGNPs/PAN fibril composites and its distribution were investigated by scanning electron microscopy (SEM) to show the minimum fiber diameter for the above‐mentioned 5 wt. % of EGNPs. A minimum fibril composite diameter of 182 nm was obtained at 10 wt.% of EGNPs. Morphological characteristics of electrospun fibers and their distribution were tested by Raman spectroscopy, SEM, differential light scattering, and high‐resolution transmission electron microscopy.     

Isolation of individual components in the electronic absorption spectra of polyaniline from the spectroelectrochemical data

The absorption spectra of polyaniline (PAN) films obtained by electrochemical polymerization on transparent SnO₂-glass electrodes are analyzed. The spectra are recorded at steady-state potentials of 0.0 to 0.8 V (Ag/AgCl) in an aqueous HC1 solution. Individual absorption bands, isolated by the Alentsev-Fok method, include both earlier known bands and some new absorption bands. The former correspond to π-π* transitions in the benzenoid rings (300-320 nm), radical cations (∼435 nm), localized polarons (∼755 nm), and quinoid structures (∼655 nm). By comparing these results with the spectroelectrochemical data obtained earlier for electrochemically synthesized PAN in solutions of various acids and for vacuum-deposited PAN, the newly found bands are assigned to different intermolecular interactions, specifically, a donor-acceptor coupling of the quinoid moieties with counter anions (at 570 nm) and an electron exchange between highly conducting domains of the film (∼900 nm)     

Comparative study of electrolessly deposited Pd/Ag films onto p-silicon (100)-activated seed layers of Ag and Pd

Pd/Ag films were electrolessly deposited onto p-silicon (100)-activated seed layers of Ag and Pd, respectively, in the solution of 0.005 mol l⁻¹ AgNO₃ + 0.005 mol l⁻¹ PdCl₂ + 4.5 mol l⁻¹ NH₃ + 0.16 mol l⁻¹ Na₂EDTA+0.1 mol l⁻¹ NH₂NH₂ (pH 10.5) at room temperature. The morphology and composition of the films were studied comparatively by using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Cathodic polarization curves for hydrogen evolution were recorded in 0.5-mol l⁻¹ H₂SO₄ without illumination, in which the obtained films served as working electrodes. The experimental results show that the film obtained on the Ag seed layer was rather a pure Ag film and not a Pd/Ag film, and the Ag deposition rate on Pd sites was much faster than that on Ag sites.     

Spectroscopic and antimicrobial studies of La, Pr, Nd and Gd complexes of a dipodal [N,N,N] chelating ligand

The lanthanide complexes of bis(benzimidazole-2′-yl-methyl)amine (BImz) having molecular formula [M(BImz)X₃H₂O]·nH₂O (M = La, Pr, Nd, or Gd; X = Cl or ClO₄ and n = 1, 2 or 3) were prepared and characterized spectroscopically through IR, ¹H and ¹³C NMR, FAB-mass, UV–visible and luminescence spectroscopy. TGA data suggested presence of coordinated and the lattice water. The oscillator strengths of the f–f transitions and the covalency parameters (β, b^1/2 and δ) have been evaluated from the electronic spectral data. The proposed hepta-coordinate geometry for the complexes has been ascertained from the molecular model computations. CV studies indicate formation of a stable quasi-reversible redox couple Gd^III/IV in the solution. The in vivo antimicrobial activities of the complexes have been evaluated against gram +ve and gram −ve bacteria and fungi.     

Effect of ionic conductivity of a PAN–PC–LiClO<Subscript>4</Subscript> solid polymeric electrolyte on the performance of a TiO<Subscript>2</Subscript> photoelectrochemical cell

A nanoparticle TiO₂ solid-state photoelectrochemical cell has been fabricated. The effect of ionic conductivity of a solid electrolyte of polyacrylonitrile (PAN)–propylene carbonate (PC)–lithium perchlorate (LiClO₄) on the performance of a photoelectrochemical cell of indium tin oxide (ITO)/TiO₂/PAN–PC–LiClO₄/graphite has been investigated. A nanoparticle TiO₂ film was deposited onto ITO-covered glass substrate by controlled hydrolysis technique. A solid electrolyte of PAN–LiClO₄ with PC plasticizer prepared by solution casting technique was used as a redox couple medium. The room temperature conductivity of the electrolyte was determined by AC impedance spectroscopy technique. A graphite electrode was prepared onto a glass slide by electron beam evaporation technique. The device shows a photovoltaic effect under illumination. The short-circuit current density, J _sc, and open-circuit voltage, V _oc, vary with the conductivity of the electrolyte. The highest J _sc of 2.82 μA cm⁻² and V _oc of 0.56 V were obtained at the conductivity of 4.2 × 10⁻⁴ Scm⁻¹ and at the intensity of 100 mW cm⁻².     

Preparation,dielectric and ferroelectric properties of (Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>)<Subscript>0.94</Subscript>Ba<Subscript>0.06</Subscript>TiO<Subscript>3</Subscript> thin films by a sol–gel process

(BiFeO₃)_1−x –(BaTiO₃) _x solid solution thin films are grown on Pt/Ti/SiO₂/Si substrates by chemical solution deposition method. Films with x = 0.00, 0.05 and 0.10 were prepared by annealing at 500°C. X-ray diffraction patterns indicate that the pure BiFeO₃ film adopts random orientation while the solid solution films are highly (100) preferentially oriented. Improved electric property at room temperature was observed in the BaTiO₃ incorporated BiFeO₃ films. The remanent polarization of the film with x = 0.0, 0.05 and 0.10 are 76.6, 51.9 and 19.7 μC/cm² respectively under a measuring electric field of 0.94 MV/cm. The BaTiO₃ incorporated BiFeO₃ films show improved fatigue endurance. By the solid solution with BaTiO₃, the leakage current density is reduced effectively.     

Fabrication and Formation Mechanism of Ag Nanoplate‐Decorated Nanofiber Mats and Their Application in SERS

We report a new simple method to fabricate a highly active SERS substrate consisting of poly‐m‐phenylenediamine/polyacrylonitrile (PmPD/PAN) decorated with Ag nanoplates. The formation mechanism of Ag nanoplates is investigated. The synthetic process of the Ag nanoplate‐decorated PmPD/PAN (Ag nanoplates@PmPD/PAN) nanofiber mats consists of the assembly of Ag nanoparticles on the surface of PmPD/PAN nanofibers as crystal nuclei followed by in situ growth of Ag nanoparticles exclusively into nanoplates. Both the reducibility of the polymer and the concentration of AgNO₃ are found to play important roles in the formation and the density of Ag nanoplates. The optimized Ag nanoplates@PmPD/PAN nanofiber mats exhibit excellent activity and reproducibility in surface‐enhanced Raman scattering (SERS) detection of 4‐mercaptobenzoic acid (4‐MBA) with a detection limit of 10^?10 m , making the Ag nanoplates@PmPD/PAN nanofiber mats a promising substrate for SERS detection of chemical molecules. In addition, this work also provides a design and fabrication process for a 3D SERS substrate made of a reducible polymer with noble metals.     

Preparation and characterization of stable monodisperse silver nanoparticles via photoreduction

Silver nanoparticles were synthesized by UV irradiation of [Ag(NH₃)₂]⁺ aqueous solution using poly(N-vinyl-2-pyrrolidone) (PVP) as both reducing and stabilizing agents. The formation of silver nanoparticles was confirmed from the appearance of surface plasmon absorption maxima around 420 nm. It was found that the formation rate of silver nanoparticles from Ag₂O was much quicker than that from AgNO₃, and the absorption intensity increased with PVP concentration as well as irradiation time. The maximum absorption wavelength (λ_max) was blue shift with increasing PVP content until 8 times concentration of [Ag(NH₃)₂]⁺ (wt%). The transmission electron microscopy (TEM) showed the resultant particles were 4–6 nm in size, monodisperse and uniform particle size distribution. X-ray diffraction (XRD) demonstrated that the colloidal nanoparticles were the pure silver. In addition, the silver nanoparticles prepared by the method were stable in aqueous solution over a period of 6 months at room temperature (25 °C).     

Voltammetry of immobilized cytochrome c on novel binary self-assembled monolayers of thioctic acid and thioctic amide modified gold electrodes

Horse heart cytochrome c (cyt c) was adsorbed on the binary self-assembled monolayers (SAMs) composed of thioctic acid (T-COOH) and thioctic amide (T-NH₂) at gold electrodes via electrostatic interaction. The cyt c adsorbed on the modified gold electrode exhibited well-defined reversible electrochemical behavior in 10 mM phosphate buffer solution (PBS, pH 7.0). The surface concentration (Γ) of electroactive species, cyt c, on the binary SAMs was higher than that in single-component SAMs of T-COOH, and reached a maximum value of 9.2 × 10⁻¹² mol cm⁻² when the ratio of T-COOH to T-NH₂ in adsorption solution was of 3:2, and the formal potential (E^0′=(E_pa+E_pc)/2) of cyt c was −0.032 V (vs. Ag|AgCl (3 M NaCl)) in a 10 mM PBS. The interaction between cyt c and the binary SAMs made the E^0′ shift negatively when compared with that of cyt c in solution (+0.258 V vs. NHE, i.e., +0.058 V vs. Ag|AgCl (3 M NaCl)). The fractional coverage of bound cyt c was a 0.64 theoretical monolayer. The standard electron transfer rate constant of cyt c immobilized on the binary SAMs was also higher than that on single-component SAMs of T-COOH, and the maximum value of 15.8 ± 0.6 s⁻¹ was obtained when the ratio of T-COOH to T-NH₂ in adsorption solution was at 3:2. The results suggest that the electrode modified with the binary SAMs functions better than the electrode modified with single-component SAMs of T-COOH.     

Electrochemical kinetics of nanosized Ag and Ag2O thin films prepared by radio frequency magnetron sputtering

Ag and Ag₂O thin films have been prepared by radio frequency magnetron sputtering on Cu substrates and have been characterized by X-ray diffraction, scanning electron microscope and atomic force microscope. The electrochemical performance of the thin films has been studied by galvanostatic cycling and cyclic voltammetry. The potential dependence of Li-ion chemical diffusion coefficients, [(D)\tilde]_\textLi {\widetilde{D}_{\text{Li}}} , of the films has been determined by galvanostatic intermittent titration technique and electrochemical impedance spectroscopy. It is found that Li-ion chemical diffusion coefficients of the Ag film range from 10⁻¹⁶ to 3 × 10⁻¹⁴ cm² s⁻¹. The Ag/Li₂O composite that is formed from Ag₂O after the first cycle exhibits higher [(D)\tilde]_\textLi {\widetilde{D}_{\text{Li}}} values than the Ag film, especially at a low Li-intercalation content. The phase transitions in the two-phase region cause a significant decrease of chemical diffusion coefficients.     

Synthesis and antimicrobial activity of Ag(I)‐N‐heterocyclic carbene complexes derived from benzimidazol‐2‐ylidene

Novel benzimidazol‐2‐ylidene carbene complexes of Ag(I) were prepared by interaction of the corresponding benzimidazolium salt with Ag₂O in dichloromethane. Their structures were characterized by elemental analyses, ¹H‐NMR, ¹³C‐NMR and IR spectroscopy techniques. All compounds studied in this work were screened for their in vitro antimicrobial activities against the standard strains: Enterococcus faecalis (ATCC 29212), Staphylococcus aureus (ATCC 29213), Escherichia coli (ATCC 25922), Pseudomonas aeruginosa (ATCC 27853) and the fungi Candida albicans and Candida tropicalis. The new complexes were found to be effective antimicrobial activity against a series of bacteria and fungi. Copyright © 2010 John Wiley & Sons, Ltd.     

Kinetic determination of silver at trace level based on its catalytic effect on a ligand substitution reaction

It is observed that Ag(I) catalyzes the rate of substitution of phenylhydrazine (PhNHNH₂) into hexacyanoferrate(II), producing a cherry red colored complex, [Fe(CN)₅PhNHNH₂]³⁻. The reaction was monitored at 488 nm leading to the formation of the complex under the conditions: [Fe(CN)₆]⁴⁻ (5.0 × 10⁻³ mol dm⁻³), PhNHNH₂ (2.0 × 10⁻³ mol dm⁻³), temperature (25 ± 0.1 °C), pH (2.8 ± 0.02), and ionic strength, I (0.02 mol dm⁻³), (KNO₃). Under optimum conditions, absorbance at fixed times (A _t ) is linearly related to Ag(I) in the concentration range 10.79–97.08 ng cm⁻³, in the presence of several diverse ions. The highest percentage error and relative standard deviations in the entire range of Ag(I) determination are found to be 2.5% and 0.16, with a detection limit of 8.75 ng cm⁻³ of silver(I). The experimental accuracies expressed in terms of percentage recoveries are in the range of 97.87–102.50. The method was successfully applied for the determination of Ag(I) in a few synthetic samples and found to be in good agreement with those obtained from atomic absorption spectrophotometry (AAS). The validity of the proposed method has also been tested for Ag(I) determination in spiked drinking water samples. The present catalytic kinetic method (CKM) is highly sensitive, selective, reproducible, and inexpensive. A review of recently published catalytic spectrophotometric methods for determination of Ag(I) has also been presented for comparison.     

Separation of curium from americium using composite sorbents and complexing agent solutions: part 2

TODGA–PAN composite sorbent and (PhSO₃H)₂–BTPhen in nitric acid solution were employed as a system for separation of curium from americium. The influence of aqueous phase composition (complexing agent and nitric acid concentrations) on weight distribution coefficients and Cm/Am separation factor was studied in batch experiments with trace amounts of ²⁴¹Am and ²⁴⁴Cm. Based on the results obtained, column experiment was designed and conducted. The Cm/Am separation factor of 3.8 ± 0.1 found in batch experiments with TODGA–PAN could be reproduced also in column experiment resulting in good separation of Cm from Am. The efficiency of Cm separation from Am in the TODGA–PAN system was compared with the analogous system with DGA resin (Triskem International). After separation on a 0.5 mL column (φ4.7 × 29 mm) the Cm fraction containing 93% of Cm(III) contained only 3% of Am(III) in optimum conditions.

     

Do oxidations of α-diols by bis(hydrogenperiodato)argentate(III) proceed according to different rate laws?

Oxidation of α-diols, namely ethylene glycol, 1,2-propanediol, and 1,2-butanediol, by [Ag(HIO₆)₂]⁵⁻ is kinetically first-order with respect to the Ag(III) complex. The dependence of observed first-order rate constants k _obs on [α-diol] can generally be expressed by: k _obs = k _x[α-diol] + k _y[α-diol]². Our experimental results demonstrate that the different rate laws derived in the oxidation reactions of ethylene glycol (J. H. Shan et al. Chin. J. Chem. 24:478, 2006) and 1,2-butanediol (J. H. Shan et al. Transition Met. Chem. 30:651, 2005) by the Ag(III) complex are probably not correct. In turn, the reaction mechanisms based on these rate laws should probably be treated with caution.     

A kinetic investigation of the oxidation of <Emphasis Type="SmallCaps">dl</Emphasis>-pipecolinate by bis(hydrogenperiodato)argentate(III) complex anion

Kinetics of oxidation of dl-pipecolinate by bis(hydrogenperiodato)argentate(III) complex anion, [Ag(HIO₆)₂]⁵⁻, has been studied in aqueous alkaline medium in the temperature range of 25–40 °C. The oxidation kinetics is first order in the silver(III) and pipecolinate concentrations. The observed second-order rate constant, decreasing with increasing [periodate] is virtually independent of [OH⁻]. α-Aminoadipate as the major oxidation product of pipecolinate has been identified by chromatographic analysis. A reaction mechanism is proposed that involves a pre-equilibrium between [Ag(HIO₆)₂]⁵⁻ and [Ag(HIO₆)(H₂O)(OH)]²⁻, a mono-periodate coordinated silver(III) complex. Both Ag(III) complexes are reduced in parallel by pipecolinate in rate-determining steps (described by k ₁ for the former Ag(III) species and k ₂ for the latter). The determined rate constants and their associated activation parameters are k ₁ (25 °C) = 0.40 ± 0.02 M⁻¹ s⁻¹, ∆H ₁^≠ = 53 ± 2 kJ mol⁻¹, ∆S ₁^≠ = −74 ± 5 J K⁻¹ mol⁻¹ and k ₂ (25 °C) = 0.64 ± 0.02 M⁻¹ s⁻¹, ∆H ₂^≠ = 41 ± 2 kJ mol⁻¹, ∆S ₂^≠ = −110 ± 5 J K⁻¹ mol⁻¹. The time-resolved spectra, a positive dependence of the rate constants on ionic strength of the reaction medium, and the consistency of pre-equilibrium constants derived from different reaction systems support the proposed reaction mechanism.     

In situ study of diffusion and interaction of water and electrolyte solution in polyacrylonitrile (PAN) membrane using FTIR and two-dimensional correlation analysis

In the study, the diffusion process of water and CaCl₂ aqueous solution in polyacrylonitrile (PAN) membrane have been investigated using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and two-dimensional (2D) correlation analysis. In 2D ATR-FTIR spectra, the water ν(OH) band in PAN membrane during both water and CaCl₂ solution diffusion is split into three separate bands. However, the OH band appearing from bound water which forms hydrogen-bonding of CaCl₂ solution diffusion has a considerably lower wavenumber than that of pure water diffusion, which is due to association between Ca²⁺ ions and the CN groups in PAN. The sequential orders of the intensity changes for water and CaCl₂ solution diffusion in the region of ν(OH) and ν(CN) bands reveal the diffusion process and interaction of water and electrolyte in PAN membrane. That is, in the process of water diffusion in PAN membrane, water molecules first interact with –CN group in PAN to form weak hydrogen bond, then the moderate hydrogen-bonding interactions start gradually, and finally, the strong hydrogen-bonding interactions may be formed. When CaCl₂ solution diffuses in PAN membrane, the CN groups in PAN first associate with Ca²⁺ ions and then interact with water molecules to form hydrogen bond that grows gradually from weak to strong. Furthermore, the results are validated further by band fitting to calculate the ratio of each component band area and the proportion of component band to ν(OH) water band.     

Photogenic MnO2/Ag metal nanocomposites and their dye adsorbing activities

• Manganese dioxide/silver (MnO₂/Ag) nanoparticles were fabricated by using KMnO₄-NaBH₄ redox reaction at room temperature. The optical and structural properties of MnO₂/Ag were determined using UV–visible and Fourier transform infrared spectroscopies. The morphology was established with scanning and transmission electron microcopies, and X-ray diffraction. MnO₂/Ag showed excellent adsorbing activity to the removal of Congo red. The various kinetic models were used to determine the rate of dye removal. Congo red adsorption onto MnO₂Ag proceeds through the pseudo-second-order kinetic model. Langmuir adsorption capacity (Q⁰_max = 97.1 mg/g), and sorption intensity (n = 1.6) were estimated with Langmuir and Freundlich adsorption isotherm models for 250 mg/L Congo red. Elovich model suggest the adsorption of Congo red with the MnO₂Ag proceeds through the film diffusion. The positive values of enthalpy changes (ΔH⁰), entropy changes (ΔS⁰), and negative Gibbs free energy changes (ΔG⁰) showed that the Congo red adsorption process was endothermic, spontaneous, and chemisorption process followed with physical mechanism. The results showed that the removal efficiency decreases from 98% to 89% after the six consecutive experiments.

     

Silver nanoplates formed at the air/water and solid/water interfaces

Silver nanoparticles and nanoplates were prepared at the air/AgNO₃ aqueous solution interfaces under poly(9-vinylcarbazole) (PVK) monolayers when illuminated by UV-light at room temperature and elevated temperatures, respectively. When the illuminated films at the air/water interfaces were covered by carbon-coated copper grids, nanoplates were formed even at room temperature, and the size of the nanoplates was much larger than those formed at the air/water interface under the same experimental conditions, indicating that copper took part in the formation of Ag nanoplates through the galvanic displacement reaction between Cu and Ag⁺ ions with the help of carbon layer to conduct electrons. It was found that the basal plane of these nanoplates is the (1 1 1) face of a face-centered cubic (fcc) Ag crystal. Although platelike structure can be formed at the carbon-coated copper grid/AgNO₃ aqueous solution interface without PVK film, it shows different features from those with PVK films, indicating that PVK film plays an important role in the formation of regular large nanoplates. Further observations indicate that special restrained microenvironment, adsorption of PVK molecules on a specific crystal face, anisotropic growth and attachment of the nanoparticles are responsible for the formation of the nanoplates.     

Kinetics of Ag/TiO2-photocatalyzed iodide ion oxidation

Abstract  

Ag-doped TiO₂ (anatase) samples (mass fraction w _Ag = 0.01 and w _Ag = 0.02) of 15.9 and 14.5 nm mean particle size and 11.46 and 10.14 m² g⁻¹ BET surface area were prepared by photodeposition. Doping results in surface plasmon resonance of the metallic silver nanoclusters at around 500 nm, but the absorption edge remains unaltered at 365 nm. Ag-doping remarkably enhances the photooxidation of iodide ion under UV light; iodine formation with Ag/TiO₂ with w _Ag = 0.01 is 16 times greater than with bare TiO₂. The reaction conforms to Langmuir–Hinshelwood kinetics with regard to both I⁻ and O₂. Increase of pH slows down iodine formation and sacrificial electron donors arrest the reaction. Pre-sonication of the catalyst slurry hinders the photocatalysis. Generation of iodine is much greater in acetonitrile than in water. Under the experimental conditions, Ag/TiO₂ with w _Ag = 0.01 is more efficient than Ag/TiO₂ with w _Ag = 0.02, and the enhanced photocatalysis is likely to be because of suppression of electron–hole pair recombination. Kinetic analysis reveals that increasing the Ag mass fraction from 0.01 to 0.02 enhances the surface pseudo-first-order rate constant but inhibits the adsorption of iodide ion and the oxygen molecule on the illuminated oxide surface.