Reversible H2 passivation of Si ≡ Si3 interface defects in (1 1 1)Si/SiO2

K-band electron spin resonance (ESR) at 4.3 K has revealed the dipole-dipole (DD) interaction effects between [1 1 1]P_b centers (^*Si ≡ Si₃ defects with unpaired sp³ hybrid [1 1 1]) at the 2 dimensional (1 1 1)Si/SiO₂ interface. This has been enabled by the perfectly reversible H₂ passivation of P_b, which affects the defect's spin state. Sequential hydrogenation at 253–353°C and degassing treatments in high vacuum at 743–835°C allowed to vary the P_b density in the range 5 × 10¹⁰ < [P_b] (1.14 ± 0.06) × 10¹³ cm^-2. With increasing [P_b] fine structure doublets are clearly resolved. It is found that (1 1 1)Si/SiO₂ interfaces, dry thermally grown at ≈920°C, naturally comprise a ^*Si ≡ Si₃ defect density — passivated or not — of 1.14 × 10¹³ cm^-2.     

Defect versus nanocrystal luminescence emitted from room temperature and hot-implanted SiO2 layers

Silicon nanocrystals have been synthesized in SiO₂ matrix using Si ion implantation. Si ions were implanted into 300-nm-thick SiO₂ films grown on crystalline Si at energies of 30–55 keV, and with doses of 5×10¹⁵, 3×10¹⁶, and 1×10¹⁷ cm⁻². Implanted samples were subsequently annealed in an N₂ ambient at 500–1100°C during various periods. Photoluminescence spectra for the sample implanted with 1×10¹⁷ cm⁻² at 55 keV show that red luminescence (750 nm) related to Si-nanocrystals clearly increases with annealing temperature and time in intensity, and that weak orange luminescence (600 nm) is observed after annealing at low temperatures of 500°C and 800°C. The luminescence around 600 nm becomes very intense when a thin SiO₂ sample is implanted at a substrate temperature of 400°C with an energy of 30 keV and a low dose of 5×10¹⁵ cm⁻². It vanishes after annealing at 800°C for 30 min. We conclude that this luminescence observed around 600 nm is caused by some radiative defects formed in Si-implanted SiO₂.     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Time-dependent response of interface states determined by using differential isothermal transient spectroscopy

A method based on the differential analysis of the isothermal transients is proposed to study the dynamical properties of the charging and discharging of interface states, and several possibilities of using this method are shown. The results obtained in SiO₂/Si and Si₃N₄/SiO₂/Si samples are in agreement with the existence of a spatial and energy distribution of interface states within the insulator. From the experimental data, the concentration of traps within the insulator at 35 Å is estimated to be 5×10⁹ cm^-2 eV^-1, with a tunneling cross section 10^-19 cm², at E_c-E ≈ 0.2 eV.     

Analysis of frequency-dependent series resistance and interface states of In/SiO2/p-Si (MIS) structures

In this work, the investigation of the interface state density and series resistance from capacitance–voltage (C–V) and conductance–voltage (G/ω−V) characteristics in In/SiO₂/p-Si metal–insulator–semiconductor (MIS) structures with thin interfacial insulator layer have been reported. The thickness of SiO₂ film obtained from the measurement of the oxide capacitance corrected for series resistance in the strong accumulation region is 220 Å. The forward and reverse bias C–V and G/ω−V characteristics of MIS structures have been studied at the frequency range 30 kHz–1 MHz at room temperature. The frequency dispersion in capacitance and conductance can be interpreted in terms of the series resistance (R_s) and interface state density (D_it) values. Both the series resistance R_s and density of interface states D_it are strongly frequency-dependent and decrease with increasing frequency. The distribution profile of R_s–V gives a peak at low frequencies in the depletion region and disappears with increasing frequency. Experimental results show that the interfacial polarization contributes to the improvement of the dielectric properties of In/SiO₂/p-Si MIS structures. The interface state density value of In/SiO₂/p-Si MIS diode calculated at strong accumulation region is 1.11×10¹² eV⁻¹ cm⁻² at 1 MHz. It is found that the calculated value of D_it (≈10¹² eV⁻¹ cm⁻²) is not high enough to pin the Fermi level of the Si substrate disrupting the device operation.     

Spectroscopy, laser operation at 1.3 μm and self-frequency doubling in GdAl3(BO3)4: Nd

We report for the first time the spectroscopy and the laser operation of GdAl₃(BO₃)₄: Nd³⁺ (NGAB) near 1338 nm corresponding to the ⁴F_3/2→⁴I_13/2 channel. Their features have been found favorable for self-frequency doubling in order to generate a red radiation at 669 nm and more generally for self-frequency conversions. The emission cross-section in σ-polarization was estimated to be 5.5×10⁻²⁰ cm². We demonstrated self-frequency doubling despite of non-optimal experimental conditions.     

Carrier relaxation in InGaAs

A modelocked Nd: YAG pumped optical parametric amplifier providing 35 ps pulses in the wavelength range λ = 1.45−2.1 μm has been used to study photoexcited carrier recombination in InGaAs. At carrier densities in excess of 10¹⁸ cm^-3 Auger processes are found to dominate the carrier recombination. An Auger rate of 2.5±0.5×10^-28 cm⁶ s^-1 is determined.     

Erbium in silicon–germanium quantum wells

Strained Si_1−xGe_x/Si quantum wells have been doped with erbium by implantation. A comparison is made with strained Si_1−xGe_x/Si quantum wells and relaxed Si_1−xGe_x, with x between 10% and 25%, doped with erbium during MBE growth. The erbium concentration was between 1×10¹⁸ and 5×10¹⁸ cm⁻³ throughout the active regions. Transmission electron microscopy, X-ray diffraction, and photoluminescence studies indicate that good regrowth can been achieved after full amorphisation by implantation of the strained quantum wells. The erbium luminescence is more intense in the Si_1−xGe_x/Si layers, but erbium-implanted samples containing Si_1−xGe_x exhibit defect luminescence in the region of 0.9–1.0 eV. These defects are also present when Si_1−xGe_x/Si quantum wells are implanted with an amorphising dose of silicon, and then regrown. They are attributed to small germanium-rich platelets, rather than to erbium-related defects. Electroluminescence is presented from a forward biased erbium-implanted Si_0.87Ge_0.13/Si structure at a drive current density of only 1.8 mA/cm².     

Domain wall pinning in polycrystalline perovskite La0.7Sr0.3MnO3

Reversible and irreversible domain wall (DW) motions have been investigated in La_0.7Sr_0.3MnO₃ ceramic samples using frequency-response complex permeability with various amplitudes of AC field. We also examine the effects of temperature in the range from 293 to 368 K and transverse DC magnetic field with a maximum of 4.40×10⁵ A/m on the real part of permeability (μ′). Two relaxations corresponding to reversible wall motions and domain rotations occur in low and high frequency regions, respectively. The irreversible DW displacements can be activated as the amplitude larger than the pinning field of 3 A/m, leading to an increase in μ′. The μ′ obeys a Rayleigh law at the temperature below 343 K or under DC field of less than 4.22×10⁴ A/m. The Rayleigh constant η increases from 5.45×10⁻² to 1.54×10⁻¹ (A/m)⁻¹ as the temperature rises from 293 to 343 K, and η decreases from 5.58×10⁻² to 3.67×10⁻² (A/m)⁻¹ with increasing DC field from 1.99×10³ to 4.22×10⁴ A/m.     

Cross section of the charged current reaction C(ve, e)Ng.s.

The charged current nuclear transition ¹²C(v_e, e⁻)¹²N_g.s. has been observed in the KARMEN experiment. The flux average cross section for v_e from μ⁺ decay at rest is determined to be σ = [8.1±0.9(stat.)±0.75 (syst.)]×10⁻⁴²cm². For the first time also the energy dependence of the cross section has been measured for neutrino energies up to 50 MeV.     

Evaluation of the diffusion length of minority carriers in bulk GaAs

The diffusion length of minority charge carriers has been investigated in LEC GaAs, silicon-doped with doping density N_D - N_A ranging from 10¹⁶ to 10¹⁸ cm^-3, by surface photovoltage (SPV) and electron-beam-induced current (EBIC) of scanning electron microscopy (SEM) measurements. Au Schottky diodes have been evaporated along the diameter of wafers cut from different doping density ingots to determine the variation of minority carrier diffusion length with both the radial position on the slice and the carrier concentration. The diffusion length values obtained by optical and electron excitation enhance systematic differences, which can be explained by the different surface recombination weight in the carrier generation volume and by the injection level, too. In all the examined samples an M-shaped radial variation of the diffusion length has been observed; on the other hand, the mean value of L_p increases from 0.5 to 7 μm when the doping concentration increases. The authors correlate this distribution to the electrical inhomogeneity induced by native defects and associated recombination centres. The role of the dislocations, which induce two competitive effects, i.e. an enhanced recombination probability and a precipitate condensation, is here discussed.     

Structural and compositional analysis of InBixAsySb(1−x−y) films grown on GaAs(0 0 1) substrates by liquid phase epitaxy

The growth of epitaxial InBi_xAs_ySb_(1−x−y) layers on highly lattice mis-matched semi-insulating GaAs substrates has been successfully achieved via the traditional liquid phase epitaxy. Orientation and single crystalline nature of the film have been confirmed by X-ray diffraction. Scanning electron micrograph shows abrupt interface at micrometer resolution. Surface composition of Bi(x) and As(y) in the InBi_xAs_ySb_(1−x−y) film was measured using energy dispersive X-ray analysis and found to be 2.5 and 10.5 at.%, respectively, and was further confirmed with X-ray photoelectron spectroscopy. Variation of the composition with depth of the film was studied by removing the layers with low current (20 μA) Ar⁺ etching. It was observed that with successive Ar⁺ etching, In/Sb ratio remained the same, while the As/Sb and Bi/Sb ratios changed slightly with etching time. However after about 5 min etching the As/Sb and Bi/Sb ratios reached constant values. The room temperature band gap of InBi_0.025As_0.105Sb_0.870 was found to be in the range of 0.113–0.120 eV. The measured values of mobility and carrier density at room temperature are 3.1×10⁴ cm² V⁻¹ s⁻¹ and 8.07×10¹⁶ cm⁻³, respectively.     

Microwave studies of the superconducting state in Rb3C60

Methods of electron-spin resonance (ESR) and direct, non-linear field-modulated microwave absorption (FMMA) were applied for the measurements in low- and high-purity samples of rubidium-doped fullerene, Rb₃C₆₀. The coexistence of the normal strong ESR signals and regular series of weak absorption lines similar to those seen in systems of Josephson junctions was observed in the high-purity sample. The possible influence of the vortex lattice on the ESR signals was also studied. We determined from FMMA investigations using the Portis model the critical field μ₀H^* = 40 μT, the depinning current density J_c^*(μ₀H₀ = 1 mT) 4 × 10⁸ A/m² in low magnetic field and J_c^*(μ₀H₀ > 100 mT) 1.6 × 10⁸ A/m² in higher fields. These values were generally one order of magnitude higher than the highest corresponding values previously observed in high-temperature superconductors (HTS's).     

硅锗量子阱结构在硅异质结太阳电池中应用的数值模拟

利用半导体工艺和器件仿真软件silvaco TCAD(Technology Computer Aided Design),模拟研究了采用硅/硅锗合金(silicon/silicon germanium alloy,Si/Si_(1-x)Ge_x)量子阱结构作为吸收层的薄膜晶体硅异质结太阳电池各项性能.模拟结果显示,长波波段光学吸收随锗含量的增加而增加,而开路电压则因Si_(1-x)Ge_x)层带隙的降低而下降.锗含量为0.25时,短路电流密度的增加补偿了开路电压的衰减,效率提升0.2%.氢化非晶硅/晶体硅(a-Si:H/c-Si)界面空穴密度以及Si_(1-x)Ge_x)量子阱的体空穴载流子浓度制约着空穴费米能级的位置,进而影响到开路电压的大小.随着锗含量增加,a-Si:H/c-Si界面缺陷对开压的影响降低,Si_(1-x)Ge_x)量子阱的体缺陷对开压的影响则相应增加.高效率含Si_(1-x)Ge_x)量子阱结构的硅异质结太阳电池的制备需要a-Si:H/c-Si界面缺陷的良好钝化以及高质量Si_(1-x)Ge_x)量子阱的生长.     

Exchange coupling effects in NiO/Co and NiO/permalloy bilayers

NiO/Co and NiO/Ni₈₀Fe₂₀ bilayers were prepared at 293 onto SiO₂(1 0 1)/Si(1 1 1) and glass substrates using UHV (5×10⁻¹⁰ mbar) RF/DC magnetron sputtering. Results on magnetic measurements showed that the exchange biasing and coercive fields are inversely proportional to the Co and Ni₈₀Fe₂₀ (Py) layer thickness down to 2 nm. A maximal RT coupling energy for the NiO–Co and NiO–Py interface was estimated as 0.04 and 0.03 mJ/m² for the samples prepared onto SiO₂(1 0 1)/Si(1 1 1) substrates.     

A new measurement of the weak magnetism term in the betaspectra of B and N

The betaspectra of ¹²B and ¹²N have been measured with a NaI crystal as spectrometer. Assuming a shape correction factor 1 + aW + bW² and b₋ = 1.106 × 10⁻⁴ MeV⁻², b₊ = −1.397 × 10⁻⁴ MeV⁻², the spectra yield a₋ = (+0.91 ± 0.11) × 10⁻² MeV⁻¹ and a₊ = (−0.07 ± 0.09) × 10⁻² MeV⁻. the a₋ − a₊ = (+0.98 ± 0.09) × 10⁻² MeV⁻¹ is in agreement with the weak magnetism prediction.     

Electrical characterization of low temperature deposited TiO2 films on strained-SiGe layers

Thin films of titanium dioxide have been deposited on strained Si_0.82Ge_0.18 epitaxial layers using titanium tetrakis-isopropoxide [TTIP, Ti(O-i-C₃H₇)₄] and oxygen by microwave plasma enhanced chemical vapor deposition (PECVD). The films have been characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). Dielectric constant, equivalent oxide thickness (EOT), interface state density (D_it), fixed oxide charge density (Q_f/q) and flat-band voltage (V_FB) of as-deposited films were found to be 13.2, 40.6 Å, 6×10¹¹ eV⁻¹ cm⁻², 3.1×10¹¹ cm⁻² and −1.4 V, respectively. The capacitance–voltage (C–V), current–voltage (I–V) characteristics and charge trapping behavior of the films under constant current stressing exhibit an excellent interface quality and high dielectric reliability making the films suitable for microelectronic applications.     

Laser ablated bismuth cuprate thin films preparation and effect of oxygen nonstoichiometry upon superconductivity

Thin films of Bi₂Sr₂CaCu₂O₈ and (Bi, Pb)₂Sr₂Ca₂Cu₃O₁₀ have been prepared on monocrystalline (100) MgO substrates, using a laser ablation method with post annealing treatment. The influence of substrate temperature and oxygen pressure during deposition were investigated. SEM observations, EDS analysis, electric and magnetic measurements have been used to characterize the films. Superconducting “2212” films, with T_c(R = 0) at 80–83 K and J_c (50 K) up to 5 × 10⁵ A/cm², have been currently achieved, while Pb-doped “2223” films exhibit T_c as high as 110 K with J_c = 5 × 10⁴ A/cm² at 77 K. The effect of annealing at low temperature (350°C) in an argon flow has been studied for the 2212 phase, it shows the influence of the oxygen non-stoichiometry, i.e. of the hole carrier density upon T_c's which can be measured up to 89 K (zero resistance).     

Optical nonlinearities and photo-excited carrier lifetime in CdS at 532 nm

Bound-electronic and free-carrier optical nonlinearities, and relaxation of photo-excited free carriers in CdS have been investigated by the use of a single-beam Z-scan technique at 532 nm. Under pulsed radiation of 35-ps duration with the input irradiances up to 4.8 GW/cm², the two-photon absorption coefficient, the bound-electron nonlinear refractive index, the free-carrier absorption cross-section, and the change in the refractive index per unit carrier density are determined to be 5.4±0.8 cm/GW, −(5.3±0.8)×10⁻¹³ cm²/W, (3.0±0.5)×10⁻¹⁷ cm² and −(0.8±0.1)×10⁻²¹ cm³, respectively. By using these values in the open-aperture Z-scans conducted with 7-ns laser pulses, the carrier recombination time is extracted to be 3.6±0.7 ns. The measured parameters are compared to theoretical calculations.     

Continuum absorption of vibrationally excited O2 from 200–320 nm

Cross sections for absorption from excited vibrational levels of the ground X³Σ^-_g state of molecular oxygen to the repulsive 1³Π_u state are given. The potential energy curve for the 1³Π_u state of O₂ is constructed to be consistent with predissociation data for the B³Σ^-u state and with recent ab initio calculations. In the photon wavelength range of 200–320 nm the cross sections are smoothly oscillatory and in no case larger than 1 × 10^-21 cm². In the region of the Schumann-Runge bands the cross sections are of order 0.4 × 10^-21 cm².