Determination of lead ions using an diantipyrylmethane-based electrode

The possibility of using diantipyrylmethane as an ionophore component of a lead-selective electrode membrane was assessed. Membrane composition (wt %) was optimized: polyvinyl chloride (31.89), dioctyl sebacate (63.81), diantipyrylmethane (2.50), and oleic acid (1.80). The proposed model of the electrode works in the concentration range of 1 × 10^–5–0.1 M with a detection limit of 2 mg/L. A slope of the electrode function of the diantipyrylmethane-based electrode is 29.4 ± 0.5 mV/pPb. Concentration of Pb(II) ions in various samples was determined.     

Lead-selective membrane electrodes based on dithiophenediazacrown ether derivatives

Three double-armed diazacrown ethers with two thiophene side groups, 7,16-dithenyl-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane (DTDC), 7,16-dithenoyl-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane (DTODC), and 7,16-di-(2-thiopheneacetyl)-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane (DTAODC), have been synthesized and used as novel neutral lead(II) ionophores in ion selective electrode applications. The relationship between the molecular structure of these ionophores and electrochemical properties (linear range, response time, selectivity) of the membrane electrode is discussed. The optimum conditions for the preparation of the electrodes are described. The optimized dithenoyldiazacrown had a detection limit of pPb = 5.7, and Nernstian range with slope 29.2 mV decade⁻¹ from pPb = 5.0 to 2.7. Mercury and silver ions are the major interferences. These electrodes are applied to potentiometric titrations of lead(II) ions and show promise for the determination of lead ions in water samples.     

Synthesis and properties of podands with 4-antipyryliminomethine groups

Novel podands with 4-antipyryliminomethine groups on benzenes and various numbers of ethers are prepared. According to UV spectroscopy, these compounds form complexes with alkali, alkaline earth, and transition metals. Extraction of metal picrates demonstrated that the podands selectively form extractable complexes with these salts. A lead-selective electrode with an electrode function 22–24 mV/pPb is based on 1,8-bis[2-(4-antipyryliminomethine)phenoxy]-3,6-dioxaoctane. This enables 1·10^–6–1·10^–2 M Pb to be determined in the pH range 3.5–5.5. The electrode is highly selective for Pb in the presence of alkali and alkaline earth metals.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 9, pp. 2099–2102, September, 1990.     

Cobalt oxide/tetraruthenated cobalt-porphyrin composite for hydrogen peroxide amperometric sensors

A new composite material constituted by mu-{5,10,15,20-tetra(4-pyridyl)porphyrinato cobalt(iii)}-tetrakis-{chloro-bis-(2,2'-bipyridine)ruthenium(ii)} complex (or CoTRP) and cobalt oxide, exhibiting high stability and sensitivity for the quantification of hydrogen peroxide, was obtained by the electrochemical polymerization of the tetraruthenated cobalt porphyrin in alkaline medium. The optimized experimental conditions for the preparation of the modified glassy carbon electrodes and for analysis of H2O2 were carefully determined. Fast sequential analysis (120 determinations h(-1)) in a wide linear dynamic range (5.0 x 10(-7) mol L(-1) to 2.0 x 10(-3) mol L(-1)), with high sensitivity and low detection limit (2.0 x 10(-7) mol L(-1)), was achieved by using these electrodes and the batch injection analysis (BIA) technique. Such characteristics allied to a good stability were explored for the specific determination of hydrogen peroxide in six commercial cosmetics and pharmaceutical product samples, giving results in excellent agreement with those obtained by the spectrophotometric method.     

On-column conductivity detection in capillary-chip electrophoresis

On-column conductivity detection in capillary-chip electrophoresis was achieved by actively coupling the high electric field with two sensing electrodes connected to the main capillary channel through two side detection channels. The principle of this concept was demonstrated by using a glass chip with a separation channel incorporating two double-Ts. One double-T was used for sample introduction, and the other for detection. The two electrophoresis electrodes apply the high voltage and provide the current, and the two sensing electrodes connected to the separation channel through the second double-T and probe a potential difference. This potential difference is directly related to the local resistance or the conductivity of the solution defined by the two side channels on the main separation channel. A detection limit of 15 microM (600 ppb or 900 fg) was achieved for potassium ion in a 2 mM Tris-HCl buffer (pH 8.7) with a linear range of 2 orders of magnitude without any stacking. The proposed detection method avoids integrating the sensing electrodes directly within the separation channel and prevents any direct contact of the electrodes with the sample. The baseline signal can also be used for online monitoring of the electric field strength and electroosmosis mobility characterization in the separation channel.     

A study on lowering the detection limit with solid-state lead-selective electrodes

The detection limit of a Pb²⁺ ion-selective electrode with a solid state (PbS/Ag₂S) membrane was successfully lowered to the nanomolar range. The electrode was applied in direct potentiometric determination of Pb²⁺ in aqueous solutions. Hydrodynamics, redox reaction at the solid-state surface as well as time dependency were investigated and found as key factors affecting the low detection limit. By optimizing these parameters improving detection limit by ca. three orders of magnitude was achieved.     

A flow injection method for the analysis of tetracycline antibiotics in pharmaceutical formulations using electrochemical detection at anodized boron-doped diamond thin film electrode

A method using flow injection (FI) with amperometric detection at anodized boron-doped diamond (BDD) thin films has been developed and applied for the determination of tetracycline antibiotics (tetracycline, chlortetracycline, oxytetracycline and doxycycline). The electrochemical oxidation of the tetracycline antibiotics was studied at various carbon electrodes including glassy carbon (GC), as-deposited BDD and anodized BDD electrodes using cyclic voltammetry. The anodized BDD electrode exhibited well-defined irreversible cyclic voltammograms for the oxidation of tetracycline antibiotics with the highest current signals compared to the as-deposited BDD and glassy carbon electrodes. Low detection limit of 10 nM (signal-to-noise RATIO = 3) was achieved for each drug when using flow injection analysis with amperometric detection at anodized BDD electrodes. Linear calibrations were obtained from 0.1 to 50 mM for tetracycline and 0.5–50 mM for chlortetracycline, oxytetracycline and doxycycline. The proposed method has been successfully applied to determine the tetracycline antibiotics in some drug formulations. The results obtained in percent found (99.50–103.01%) were comparable to dose labeled.     

Continuous flow analysis of lead (II) and mercury (II) with substituted diazacrown ionophore membrane electrodes

A novel flow cell for use with ion-selective membrane electrodes is reported in which the carrier stream is drawn through a tube that suppresses the pump noise. PVC membrane electrodes based on 7,16-dithenoyl-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane (DTODC), and 7,16-di-(2-thiopheneacetyl)-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane (DTAODC) for lead (II), and 7,16-dithenyl-1,4,10,13-tetraoxa-7,16-diazacyclooctadecane (DTDC) and 7,16-di-(2-methylquinolyl)-1,4,10,13-tertraoxa-7,16-diazacyclootadecane (DQDC), for mercury (II) were prepared and evaluated. The linear ranges were pPb: 5.5-3.0 (DTODC) and 6.0-2.0 (DTAODC); pHg: 5.5-3.0 (DTDC) and 4.5-2.5 (DQDC). With flow rate of 3 ml min(-1) the repeatability of measurements was less than 5% RSD (n = 3). The system was applied to the determination of lead (II) and mercury (II) in spiked natural water samples.     

Selective amperometric detection of dopamine using OPPy-modified diamond microsensor system

Highly boron-doped diamond microfiber electrodes (BDDMF) were fabricated and characterized by the use of Scanning Electron Microscopy (SEM), Raman spectroscopy, and cyclic voltammetry. Amperometric detection of dopamine (DA), a neurotransmitter was achieved at pH 7.0, using BDDMF electrodes. The interferences from ascorbic acid (AA) and DOPAC were efficiently eliminated by using overoxidized polypyrrole-modified BDDMF electrodes, which also increased the sensitivity for the detection of dopamine. The limit of detection (S/N = 3) for dopamine was 0.1 nM, which is one order lower than that observed for carbon microfiber electrodes (CMFE), and the linear dynamic range was obtained from 0.5 nM to 100 microM (r2 = 0.997). The amperometric response for 0.5 nM dopamine has shown high stability with an RSD of 5.4% (n = 5). Highly reproducible results were obtained with an RSD of 6.2% for 10 measurements of 1 nM DA taken during 10 h and also remained the same, during measurements for 7 days, with no variation in efficiency for rejection of AA and DOPAC.     

Detection of chlorinated quinones using interdigitated electrodes coupled with capillary electrophoresis

An array of eight interdigitated microband gold electrodes (IDEs) has been developed together with electrophoretic separation for analysis of chlorinated hydroquinones (ClHQs) and benzoquinones (ClBQs). The IDE chip positioned very close to the separation capillary outlet served as an amplification/detection system without the requirement for frequent "capillary-electrode" alignment. ClHQs, electrophoretically migrating to the IDE surface, were oxidized at +1.1 V by seven electrodes of the array and then detected by the remaining electrode, poised at -0.1 V. Conversely, ClBQs were detected at +1.1 V by the detecting electrode after having been reduced at the 7 adjacent electrodes poised at -0.1 V. There was an amplification effect on both the detecting electrode as well as the adjacent electrodes because of the recycle between ClHQs and ClBQs. The detecting "amplification" current response was dependent on the potentials applied, the position of the detecting electrode on the array, the number of adjacent electrodes being used for recycling and the distance between the oxidative and reductive electrodes. Micellar electrokinetic chromatography (MEKC) separation of the analytes was achieved using 30 mM sodium dodecyl sulfate (SDS) with a detection limit in the range of 2-20 micro M. In addition to a facile "capillary-electrode" alignment, the important aspect described here was the capability of detecting through recycling a reduced compound (in the case of ClHQs) at a negative potential to circumvent fouling and electroactive interferences. An appealing feature was also the concurrent oxidation/reduction detection for each compound to ascertain peak assignment, as interfering compounds are less likely to exhibit the same oxidative/reductive characteristics and electrophoretic mobilities as the target analytes.     

Amperometric determination of acetylsalicylic acid in drugs by batch injection analysis at a copper electrode in alkaline solutions

This paper describes the determination of acetylsalicylic acid (ASA) as salicylate (SA) in pharmaceutical formulations by using amperometric detection with copper electrodes in 0.10 mol l(-1) NaOH solution. Batch injection analysis (BIA) was explored for this application. The system exhibited sharp current response peaks, rapid washout and excellent repeatability. A large linear dynamic range from 1 to 1000 mumol l(-1) was obtained by using an injected volume of 100 mul, with a detection limit of 0.48 mumol l(-1). R.S.D. of 0.37% for 30 repetitive (1x10(-4) mol l(-1)) injections and sampling frequency of 60 h(-1) were achieved. The results obtained using this system for ASA determination in seven different drug samples compared well with those found by spectrophotometry (Trinder test).     

Differential pulse polarographic determination of the herbicides atrazine, prometrine and simazine

A differential pulse polarographic method, using the dropping mercury electrode for the determination of the herbicides atrazine, prometrine and simazine is described. The optimum pH is 2. The limit of detection is 8 x 10(-8)M, corresponding to about 15 mu/l. The electrochemical behaviour of the compounds on glassy-carbon and mercury-coated glassy-carbon electrodes was also examined with a view to its use for electrochemical detection of the herbicides after their separation by HPLC.     

A comparative study of liquid and solid inner contact roxatidine acetate ion-selective electrode membranes

A comparative study was conducted using two designs of a roxatidine acetate (ROX)-selective electrode; a conventional liquid inner contact called electrode A and a graphite-coated solid contact called electrode B. The fabrication of electrodes was based on roxatidine-tetraphenylborate (ROX-TPB) as an ion-association complex in a PVC matrix using different plasticizers. Electrode A has a linear dynamic range of 2.2×10-5 mol/L to 1.0×10-2 mol/L, with a Nernstian slope of 54.7 mV/decade and a detection limit of 1.4×10-6 mol/L. Electrode B shows linearity over the concentration range of 1.0×10-6 mol/L to 1.0×10-2 mol/L, with a Nernstian slope of 51.2 mV/decade and a limit of detection of 1.1×10-7 mol/L which is remarkably improved as a result of diminishing ion fluxes in this solid contact, ion-selective electrode. The proposed sensors display useful analytical characteristics for the determination of ROX in bulk powder and its pharmaceutical formulation. The present electrodes show clear discrimination of ROX from several inorganic, organic ions, sugars, some common drug excipients and the degradation product (3-[3-(1-piperidinyl methyl) phenoxy] propyl amine) of ROX. Furthermore, the proposed electrodes were utilized for the determination of ROX in human plasma, where electrode B covers drug Cmax which indicated its applicability to pharmacokinetic, bioavailability and bioequivalent studies. The results obtained by the proposed electrodes were statistically analyzed and compared with those obtained by a reported HPLC method. No significant difference for either accuracy or precision was observed.     

Determination of melamine based on electrochemiluminescence of Ru(bpy)3(2+) at bare and single-wall carbon nanotube modified glassy carbon electrodes

The electrochemiluminescence (ECL) of Ru(bpy)(3)(2+) at bare and single-wall carbon nanotube (SWNT) modified glassy carbon (GC) electrodes has been employed for the determination of melamine for the first time, giving a linear response (R(2) = 0.99682) for melamine concentration from 1.0 × 10(-10) to 1.0 × 10(-5) M at a bare GC electrode in pH 10 borate buffer, and the detection limit is 1.0 × 10(-10) M. However, the detection limit can be reduced further to 1.0 × 10(-13) M after modification of the GC electrode by SWNTs. This is much lower compared to other detection methods. The proposed method was applied to the determination of melamine added to a commercial milk sample; the recovery is quite satisfactory with good reproducibility and stability. All of these results provide the possibility of developing a novel ECL detection method for melamine.     

Inkjet-printed gold nanoparticle electrochemical arrays on plastic. Application to immunodetection of a cancer biomarker protein

Electrochemical detection combined with nanostructured sensor surfaces offers potentially low-cost, high-throughput solutions for detection of clinically significant proteins. Inkjet printing offers an inexpensive non-contact fabrication method for microelectronics that is easily adapted for incorporating into protein immunosensor devices. Herein we report the first direct fabrication of inkjet-printed gold nanoparticle arrays, and apply them to electrochemical detection of the cancer biomarker interleukin-6 (IL-6) in serum. The gold nanoparticle ink was printed on a flexible, heat resistant polyimide Kapton substrate and subsequently sintered to create eight-electrode arrays costing <0.2 euro per array. The inkjet-printed working electrodes had reproducible surface areas with RSD <3%. Capture antibodies for IL-6 were linked onto the eight-electrode array, and used in sandwich immunoassays. A biotinylated secondary antibody with 16-18 horseradish peroxidase labels was used, and detection was achieved by hydroquinone-mediated amperometry. The arrays provided a clinically relevant detection limit of 20 pg mL(-1) in calf serum, sensitivity of 11.4 nA pg(-1) cm(-2), and a linear dynamic range of 20-400 pg mL(-1).     

Amperometric detection of catecholamines with liquid chromatography at a novelly constructed prussian blue chemically modified electrode

A novel Prussian blue chemically modified electrode (CME) was constructed and characterized for liquid chromatography electrochemical detection (LCEC) of catecholamines. Both anodic and cathodic peaks could be obtained by monitoring at constant applied potential at anodic and slightly cathodic potential ranges (0.3-0.7 and -0.2-0.1 V vs. SCE), respectively. When arranged in a series configuration, using the modified electrodes as generating and collecting detectors, extremely high effective collection efficiencies of 0.91 (for norepinephrine) and 0.58 (for dihydroxyphenylacetic acid) were achieved in dual-electrode LCEC for catecholamines; and a linear response range over 3 orders of magnitude and a detection limit of 10 pg were obtained with a downstream CME as the indicating detector.     

Manganese Detection with a Metal Catalyst Free Carbon Nanotube Electrode: Anodic versus Cathodic Stripping Voltammetry

Anodic stripping voltammetry (ASV) and cathodic stripping voltammetry (CSV) were used to determine Mn concentration using metal catalyst free carbon nanotube (MCFCNT) electrodes and square wave stripping voltammetry (SWSV). The MCFCNTs are synthesized using a Carbo Thermal Carbide Conversion method which results in a material that does not contain residual transition metals. Detection limits of 120 nM and 93 nM were achieved for ASV and CSV, respectively, with a deposition time of 60 s. CSV was found to be better than ASV in Mn detection in many aspects, such as limit of detection and sensitivity. The CSV method was used in pond water matrix addition measurements.     

New polyacrylate-based lead(II) ion-selective electrodes

A novel polyacrylate-based matrix for potentiometric ion-selective electrodes has been developed. Isododecyl acrylate, acrylonitrile and hexanedioldiacrylate co-monomers along with the thermo-initiator 2,2-dimethoxy-2-phenylacetophenone were used as polymeric matrix components. A lead(II)-selective electrode (Pb-ISE) was constructed using the above matrix. The electrode showed comparable analytical performance in the micromolar range to Pb-ISEs with conventional poly(vinyl chloride)-based membranes containing neutral ionophore and with solid-state membranes containing a mixture of lead sulphide and silver sulphide. Electrochemical impedance spectroscopy studies revealed much lower ion mobility in the polyacrylate membrane than in plasticized poly(vinyl chloride) membranes. This result additionally indicates the possibility of obtaining a lower detection limit for ISEs using the new acrylate matrix.     

直接电位法测定工业废水中的硫氰酸根离子

用直接电位法测定了统扑净生产废水和印染厂排放废水中硫氰酸根的浓度。在温度为 1 6℃ ,浓度为 0 .0 2 mol/L HCl的体系中 ,以功能高分子 PVC-双硫腙 -铜 ( I)载体的 SCN-离子电极在 SCN-离子浓度为 1 .0× 1 0 -2 ～ 5× 1 0 -6mol/L时呈能斯特响应 ,斜率为 58± 2 m V/dec,检出限为 2 .0× 1 0 -6mol/L。电极的选择性次序为 :SCN->>Cl O4 -～Sal->>Cl->NO3 ->HPO4 2 ->SO4 2     

基于3种荧光化合物检测草酰氯气体的化学发光试纸法

研究了3种发光材料聚芴(PF)、5,5'-双(9,9-二辛基芴)-2,2'-联噻吩(F-T-T-F) 和4,7-双(5-(9,9-二丙基芴)噻吩)苯并噻二唑(3FT-BTD) 的固态化学发光。 将这3种材料吸附于滤纸上得到了相应的检测试纸,研究了其与草酰氯蒸气的相互作用。 与溶液体系相比,基于试纸的固态化学发光时间可以延长至8~10 min。 该方法对草酰氯蒸气的检测限较低,分别为0.013 mg/m³(PF)、0.27 mg/m³(F-T-T-F)和1.8 mg/m³(3FT-BTD)。 制备的检测试纸可以反复暴露于草酰氯蒸气中引发化学发光,发光强度没有明显的降低,说明试纸有很好的重复使用性。 由于该试纸对草酰氯有选择性的作用,因此可以对毒性草酰氯气体进行简便的可视化检测。