电化学合成铜配合物的研究

采用金属铜为"牺牲"阳极,首次在无隔膜电解槽中,电化学溶解金属铜一步制备了纳米CuO前体Cu(OEt)2, Cu(OBu)2, Cu(acac)2, Cu(OEt)(acac), Cu(OBu)(acac) (acac为乙酰丙酮基).产物通过红外光谱(FT-IR)、拉曼光谱(Raman spectrum)进行表征.同时讨论了影响电合成铜醇盐及其配合物的关键因素.实验表明,防止阳极钝化,温度控制在30～50 ℃,采用有机胺溴化物为导电盐, 电极电位控制在0.8～1.2 V之间,可以提高电合成效率.实验同时表明Cu(acac)2, Cu(OEt)(acac), Cu(OBu)(acac)可作为制备含铜纳米材料前驱体.     

电合成系列锌配合物及纳米ZnO的制备

采用锌金属为“牺牲”阳极,首次在无隔膜电解槽中,电化学一步法制备了纳 米ZnO前驱体锌配合物Zn(OEt)_2, Zn(OBu)_2, Zn(acac)_2, Zn(OEt)_2(acac)_2, Zn(OBu)_2(acac)_2(acac为乙酰丙酮基),产物通过红外光谱(FTIR)、拉曼光谱和 核磁共振进行表征。同时采用含Zn(OEt)_2(acac)_2的电解液直接水解制备纳米 ZnO粉体,纳米ZnO通过拉曼光谱、X射线粉末衍射(XRD)和透射电子显微镜（TEM） 进行表征。实验表明电解时防止阳极钝化,控制温度在50～60 ℃之间,采用有机 胺溴化物为导电盐,可以提高电合成效率;电解合成Zn(acac)_2, Zn(OEt)_2 (acac)_2, Zn(OBu)_2(acac)_2的电流效率比Zn(OEt)_2, Zn(OBu)_2高,其中Zn (OEt)_2(acac)_2适宜作为溶胶-凝胶法制备纳米ZnO的原料,制备得到的纳米ZnO经 600 ℃煅烧后呈球形单分散结构,平均粒径在5～10nm左右。     

电化学方法制备纳米NiO及反应机理初探

采用电化学法一步制备了镍醇盐配合物Ni(OEt) 2 (acac) 2 (acac为乙酰丙酮基 ) ,并以其作为前驱体 ,控制一定水解条件制得胶体 ,分别在 4 5 0℃ ,60 0℃煅烧均得到具有立方晶型的纳米NiO粉体 .通过红外光谱 (FT_IR)、核磁共振 (1HNMR)、拉曼光谱 (Ramanspectrum)、X_射线粉末衍射 (XRD)、透射电子显微镜 (TEM)等手段对前驱体和NiO粉体进行了表征 .结果表明 ,电解合成的最佳温度为 30～ 4 0℃ ,不溶性镍醇盐配合物升温到 4 0～ 5 0℃即可溶解 .电解法制备得到的纳米NiO层呈球形单分散结构 ,粒径在 10～ 15nm左右 .本文同时讨论了电合成纳米NiO的反应机理     

钛醇盐电化学合成的研究

采用钛金属为“牺牲”阳极,首次在无隔膜电解槽中,电化学一步法制备了纳米TiO~2前驱体钛醇盐Ti(OEt)~4,Ti(OPr-i)~4,Ti(OBu)~4。产物通过元素分析、红外光谱(FT-IR)、拉曼光谱进行表征。电化学一步法直接制备纳米材料前驱体钛醇盐,克服了传统化学方法合成金属醇盐步骤多、产率低、纯度达不到要求及后续分离繁琐等缺点。本文同时讨论了影响电合成钛醇盐的关键因素及可能的反应机理,实验表明钛在醇溶液中呈点蚀行为,钛醇盐卤化物Ti(Ⅲ)(OR)~nBr~m在阳极形成,然后被氧化为Ti(Ⅳ)(OR)~nBr~m,这种物质在阴极上ROH参与下被还原生成钛醇盐Ti(OR)~4,钛阳极表面拉曼光谱证实了上述观点。防止阳极钝化,温度控制在50～60℃之间,彩有机胺溴化物为导电盐,可以提高电合成收率。     

不同镍盐合成的球形β—Ni（OH）2的充放电特性与结构变化规律

采用均匀络合共沉淀法,以不同的镍盐分析合成出了球形β－Ni(OH)2并对其充放电循环及循环伏安特性进行了研究,发现由不同盐合成的Ni(OH)2其电化学性能有较大差别,用NiSO4合成的Ni(OH)2放电比容量高,循环寿命较好,平台电位也高于用Ni(NO3)2合成的Ni(OH)2。根据X射线（XRD）分析和傅立叶变换红外（FTIR）图谱对存在差别的原因进行分别,为原料的选择提供了理论依据。     

电化学合成系列锡配合物及纳米SnO2的制备

采用锡金属为"牺牲"阳极,首次在无隔膜电解槽中,电化学一步法制备了纳米SnO₂前驱体锡配合物Sn(OEt)₄, Sn(OBu)₄, Sn(OCH₂CH₂OCH₃)₄, Sn(OEt)₂(acac)₂, Sn(OBu)₂(acac)₂, Sn(OCH₂CH₂OCH₃)₂(acac)₂[acac为乙酰丙酮基],产物通过红外光谱(FT-IR)、拉曼光谱和核磁共振进行表征.同时采用含Sn(OR)₂(acac)₂>的电解液直接水解制备纳米SnO₂粉体,纳米SnO₂通过X射线粉末衍射(XRD)和透射电子显微镜(TEM)进行表征.实验表明,电解时防止阳极钝化,控制温度在40～60℃之间,采用有机胺溴化物为导电盐,可以提高电合成效率;电解合成Sn(OCH2CH₂OCH₃)₄, Sn(OEt)₂(acac)₂, Sn(OBu)₂(acac)₂, Sn(OCH₂CH₂OCH₃)₂(acac)₂的电流效率比Sn(OEt)₄, Sn(OBu)₄高,适宜作为溶胶-凝胶(Sol-gel)法制备纳米SnO₂的原料,制备得到的纳米SnO₂经600℃煅烧后呈球形单分散结构,晶型为四方锡石型,平均粒径在(10±0.4) nm左右.     

纳米LiAlO2 前驱体的电化学合成

在35 mmol·L-1 Bu4NBr的乙醇溶液中加入180 mg锂片,采用金属阳极溶解法控制电流为0.2 A电解铝片6 h,同时间断滴入0.9 mL乙酰丙酮,制得纳米LiAlO2的前驱体LiAl(Oet)4-n(acac)n[acac为乙酰丙酮基],其结构经IR, XRD, TEM, TG-DTA表征.实验结果表明电解温度为50 ℃,导电盐Bu4NBr浓度为35 mmol·L-1时电流效率在90%以上.在温度为40 ℃,前驱体浓度为300 mmol·L-1, pH=9.0的条件下,水解6 h得粒径20 nm～30 nm的前驱体干凝胶粉,产率可达94.8%;干凝胶粉在550 ℃煅烧可得纳米LiAlO2粉体.     

Cu(Ⅰ)与丙二腈、2,2′-联吡啶及邻菲罗啉配合物的电化学合成及荧光光谱

用牺牲金属阳极的电化学方法合成两种新的一价铜配合物Cu（Ⅰ）(dipy)[CH(CN)2]及Cu(Ⅰ)(phen)[CH(CN)2]。利用元素分析,红外光谱,核磁共振确证了配合物的组成,并研究了配合物的结构,荧光光谱和电合成机理。     

非水体系中电解镍中间产物制备纳米NiO

采用纯镍为阳极，乙酰丙酮和乙醇的混合溶液中加入少量有机胺导电盐为电解液，施加一定电流使镍溶解，然后将电解液直接水解，控制一定的水解条件，制备得到纳米NiO粉体. 采用拉曼光谱、红外光谱、元素分析、XRD 和TEM 分别对电解得到的纳米NiO前驱体和纳米NiO进行了分析与表征, 并探讨了电化学溶解镍金属法制备纳米NiO反应的影响因素.电化学溶解镍金属得到的前驱体为Ni(OEt)2(acac)2,这种不溶性镍醇盐配合物升温至40～50℃即可溶解于乙醇溶液中,可直接应用于溶胶 凝胶(Sol gel)过程.水解后的纳米NiO呈无定形结构, 350 ℃煅烧后形成立方晶型NaCl结构, 纳米NiO经600 ℃煅烧后粒径分布在5～10 nm. 该方法理论上为二价不溶性金属醇盐经溶胶 凝胶工艺制备纳米氧化物材料提供了一条新的途径.     

纳米NiAl_2O_4前驱体的电化学合成

在乙醇溶液中,按Ni/Al电量比为1∶3依次电解铝片和镍片,制得复合氧化物纳米粉体NiO Al2O3的前驱体NiAl2(OCH2CH3)(8-y)(acac)y[acac为乙酰丙酮基].产物通过红外光谱、X射线衍射、电子透射显微镜进行了表征,同时研究了镍电极在铝醇盐溶液中的电化学行为,讨论了影响电合成镍、铝醇盐配合物的关键因素.实验表明,电解温度控制在54～60℃、导电盐Bu4NBr浓度为0.040～0.045mol/L时,电流效率约为93%.水解后的干凝胶粒径在10nm左右,为纳米NiAl2O4粉体的制备创造了条件.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.