Wave propagation in deep-subwavelength mode waveguides

This Letter proposes a dielectric waveguide with deep-subwavelength mode sizes. Results of both frequency domain and time domain analysis show that the effective mode area is below λ(0)(2)/400 and can even reach λ(0)(2)/1000 (λ(0) is the wavelength in vacuum). The effective electrical mode area can be comparable to that of a hybrid plasmonic subwavelength confinement waveguide, with reduced optical absorption. In contrast to slot waveguides, which guide light in low-index materials, the proposed structure guides light in high-index materials. Results obtained in this Letter show that the losses are sensitive to the surface roughness on the tens of nanometers scale. The structure can be used to design ring resonators with a quality factor comparable to that of a diffraction-limited dielectric ring resonator with the same standing wave numbers. The property can be applied in nonlinear effect enhancement or laser design with ultralow threshold.     

A high-quality factor hybrid plasmonic nanocavity based on distributed Bragg reflectors

Herein,we propose a high-quality(Q) factor hybrid plasmonic nanocavity based on distributed Bragg reflectors(DBRs) with low propagation loss and extremely strong mode confinement.This hybrid plasmonic nanocavity is composed of a high-index cylindrical nanowire separated from a metal surface possessing shallow DBRs gratings by a sufficiently thin low-index dielectric layer.The hybrid plasmonic nanocavity possesses advantages such as a high Purcell factor(Fp) of up to nearly 20000 and a gain threshold approaching 266 cm~(-1)at 1550 nm,promising a greater potential in deep sub-wavelength lasing applications.     

A low-threshold nanolaser based on hybrid plasmonic waveguides at the deep subwavelength scale

A novel nanolaser structure based on a hybrid plasmonic waveguide is proposed and investigated. The coupling between the metal nanowire and the high-index semiconductor nanowire with optical gain leads to a strong field enhancement in the air gap region and low propagation loss, which enables the realization of lasing at the deep subwavelength scale.By optimizing the geometric parameters of the structure, a minimal lasing threshold is achieved while maintaining the capacity of ultra-deep subwavelength mode confinement. Compared with the previous coupled nanowire pair based hybrid plasmonic structure, a lower threshold can be obtained with the same geometric parameters. The proposed nanolaser can be integrated into a miniature chip as a nanoscale light source and has the potential to be widely used in optical communication and optical sensing technology.     

Compact and silicon-on-insulator-compatible hybrid plasmonic TE-pass polarizer

Hybrid plasmonic waveguides consisting of a metal plane separated from a high-index medium by a low-index spacer have recently attracted much interest. Here we show that, by suitably choosing the dimensions and material properties of the hybrid waveguide, a very compact and broadband TE-pass polarizer can be implemented. Finite-difference time-domain simulation indicates that the proposed device can provide large extinction ratio with low insertion loss for the TE mode.     

Enhancing Bremsstrahlung production from ultraintense laser-solid interactions with front surface structures

A new type of a coaxial multi-layer plasmonic waveguide is proposed. The mode propagation properties are analyzed at the communication working wavelength. Theoretical investigations reveal that the enhanced optical confinement can be achieved in the two low-index dielectric media layers. The mode size can be sub- or deep sub-wavelength scale. The mode propagation loss can be well compensated by replacing the high-index dielectric media with gain material to achieve longer propagation length with better mode confinement. The comparisons of the mode properties between the proposed waveguide and waveguides studied in the published literatures are also considered. These investigations potentially lay the groundwork for the further applications of nanowire type multilayer hybrid structures. This structure could also enable various applications such asnanophotonic waveguides, high-quality nanolasers, and optical trapping and biosensors.     

Nanotube based hybrid plasmon polariton waveguide for propagation loss reduction and enhanced field confinement inside the gap region at the subwavelength scale

We present a comprehensive numerical investigation on the guiding properties of a nanotube based hybrid plasmonic waveguide, which comprises a high-index dielectric nanotube placed above a metallic substrate. It is shown that the incorporation of the nanotube offers additional freedom for tuning the optical performance of the hybrid plasmonic structure when compared to the traditional nanowire based hybrid counterparts, which enables further reduction of the propagation loss and enhanced field confinement inside the gap region, while simultaneously maintaining a subwavelength mode size at appropriate geometries. Systematic geometric parameters mapping considering the size of the nanotube and the dimension of the gap reveals that the tradeoff between the confinement and loss could be further balanced through optimizing key physical parameters. These investigations potentially lay the groundwork for the further applications of nanotube based hybrid structures.     

Subwavelength propagation and localization of light using surface plasmons: A brief perspective

Surface plasmons at the metal–dielectric interface have emerged as an important candidate to propagate and localize light at subwavelength scales. By tailoring the geometry and arrangement of metallic nanoarchitectures, propagating and localized surface plasmons can be obtained. In this brief perspective, we discuss: (1) how surface plasmon polaritons (SPPs) and localized surface plasmons (LSPs) can be optically excited in metallic nanoarchitectures by employing a variety of optical microscopy methods; (2) how SPPs and LSPs in plasmonic nanowires can be utilized for subwavelength polarization optics and single-molecule surface-enhanced Raman scattering (SERS) on a photonic chip; and (3) how individual plasmonic nanowire can be optically manipulated using optical trapping methods.     

Guided subwavelength slow-light mode supported by a plasmonic waveguide system

We introduce a plasmonic waveguide system, which supports a subwavelength broadband slow-light guided mode with a tunable slowdown factor at a given wavelength. The system consists of a metal-dielectric-metal (MDM) waveguide side-coupled to a periodic array of MDM stub resonators. The slowdown factor at a given wavelength can be tuned by adjusting the geometrical parameters of the system. In addition, there is a trade-off between the slowdown factor and the propagation length of the supported optical mode. Finally, we show that light can be coupled efficiently from a conventional MDM waveguide to the plasmonic waveguide system.     

Tailoring terahertz near-field enhancement via two-dimensional plasmons

We suggest a novel possibility for electrically tunable terahertz near-field enhancement in flatland electronic materials supporting two-dimensional plasmons, including recently discovered graphene. We employ electric-field effect modulation of electron density in such materials and induce a periodic plasmonic lattice with a defect cavity. We demonstrate that the plasmons resonantly excited in such a periodic plasmonic lattice by an incident terahertz radiation can strongly pump the cavity plasmon modes leading to a deep subwavelength concentration of terahertz energy, beyond λ/1000, with giant electric-field enhancement factors up to 10(4), which is 2 orders of magnitude higher than achieved previously in metal-based terahertz field concentrators.     

Enhancing surface plasmon polariton propagation by two-layer dielectric-loaded waveguides on silver surface

We report a study of a two-layer dielectric-loaded surface plasmon polariton waveguide (TDLSPPW) which consisted of two dielectric layers (high-index/low-index) on a silver film. The discontinuity of the electric field at the interfaces resulted in a concentrated field in the low-index region. It efficiently reduced the propagation loss of the surface plasmon polariton mode. The mode fields and corresponding complex propagation constants were calculated by a vector finite-difference method. The propagation properties were measured by a modified near-field optical microscope. It is confirmed that the propagation length of the proposed TDLSPPW was about 1.6 times longer than conventional single-layer SPP waveguides. In addition, a 90^° waveguide turn with 3 μm radius showed that the bending loss was smaller than 2 dB.     

Surface-plasmon-assisted guiding of broadband slow and subwavelength light in air

A class of axially uniform waveguides is introduced, employing a new mechanism to guide light inside a low-index dielectric material without the use of photonic band gap, and simultaneously exhibiting subwavelength modal size and very slow group velocity over an unusually large frequency bandwidth. Their basis is the presence of plasmonic modes on the interfaces between dielectric regions and the flat unpatterned surface of a bulk metallic substrate. These novel waveguides allow for easy broadband coupling and exhibit absorption losses limited only by the intrinsic loss of the metal.     

Reducing crosstalk between nanowire-based hybrid plasmonic waveguides

Hybrid plasmonic waveguides based on a surface oxidized dielectric nanowire placed on a metal surface can facilitate simultaneously deep subwavelength mode confinement and large propagation length. Directional coupling based on such waveguides are theoretically investigated. Much lower crosstalk is noticed for such hybrid plasmonic waveguides compared to conventional waveguides based on bare dielectric nanowires. Some modifications, such as vertically placing the metal surfaces or using a metallic block between the nanowires, are studied which can further reduce the crosstalk between two waveguides. The proposed low crosstalk structures based on hybrid plasmonic waveguides can provide a simple platform for plasmonic integration which can at the same time easily interface with traditional photonic circuits.     

Analysis of symmetric and asymmetric nanoscale slab slot waveguides

Nanoscale slab slot waveguides provide for high optical confinement and have found abundant applications in silicon photonics. After developing an analytical mode solver for general asymmetric slot waveguides, the confinement performance of symmetric as well as asymmetric geometries was systematically analyzed and compared. For symmetric structures, 2D confinement optimization by varying both low-index slot and high-index slab width revealed a detailed saturation trend of the confinement factor with the increase of the studied width. Furthermore, simple design rules on how to choose the slot and slab width for achieving optimal confinement was obtained. For asymmetric structures, we demonstrated that the confinement performance was always lower than the 2D optimized confinement of the symmetric structures providing the two high-index slab layers and the two cladding layers have same refractive indices, respectively. In addition, the sensitivity of the confinement to the degree of asymmetry was studied, and we found that the fabrication tolerance on the material and structural parameters may be reasonably large for symmetric structures designed at optimal confinement.     

深亚波长约束的表面等离子体纳米激光器研究

本文提出了一种新颖的基于半导体纳米线/空气间隙/金属薄膜 复合结构的表面等离子体纳米激光器, 并给出了理论研究和仿真分析. 这种结构通过金属界面的表面等离子体模式与高增益介质纳米线波导模式耦合, 从而使场增强效应得到显著提高. 同时通过数值仿真研究, 得到该混合波导结构的模式特性和增益阈值随空气槽宽度、纳米线半径的变化规律, 表明它可以实现对输出光场的深亚波长约束, 同时保持低损耗传输和高场强限制能力. 通过最优化选择, 最终得到纳米等离子体激光器的最优结构尺寸. 关键词： 表面等离子体 混合等离子体波导 纳米激光器     

All-solid photonic bandgap fiber

We describe the design and fabrication of a photonic bandgap fiber formed with two different glasses. As in a hollow-core fiber, light is guided in a low-index core region because of the antiresonances of the high-index strands in the fiber cladding. The structure described represents an ideal bandgap fiber that exhibits no interface modes and guides over the full width of multiple bandgaps.     

金属微结构纳米线中等离激元传播和分光特性

本文从理论和实验两方面探讨了具有微结构的金属纳米线系统中表面等离激元传播规律和分光特性. 我们由麦克斯韦方程组出发, 利用严格耦合波近似和有限元差分等方法首先从理论上给出了金属纳米线系统中等离激元的色散关系和能带特征, 然后基于微结构的银纳米线及其等离激元能带结构, 设计并制备出等离激元分光原型器件, 实验展示其将不同频率的光在微小空间分离的特性. 该研究结果是我们前期相关工作的延续和补充, 可应用于构造多功能集成的光子芯片和新型亚波长光电材料和器件.     

Gain-assisted indented plasmonic waveguide for low-threshold nanolaser applications

A subwavelength plasmonic indented waveguide with an active InGaAsP core is proposed.The characteristics of the gap plasmon mode and gain required for lossless propagation are investigated and analyzed by the finite element method.We numerically calculate the normalized mode areas and percentages of energy confined in InGaAsP and metal for plasmonic nanolaser applications.It is shown that the indentation of the sidewalls has an optimal value for which the lasing threshold gain is minimal.The structure could enable low-threshold subwavelength lasing and applications for optoelectronic integrated circuits.     

Enhancement of light extraction from freestanding GaN nanocolumn slab with bottom subwavelength nanostructures

It is of great interest to investigate a freestanding GaN nanocolumn slab with bottom subwavelength nanostructures. A low-index buffer layer offers more paths accessible to emit light in air, and the nanostructures break the total internal reflection condition at the bottom surface to improve the light-extraction efficiency. The GaN nanocolumns and subwavelength nanostructures can also effectively suppress optical reflection over a broad wavelength range. In this work, the freestanding GaN nanocolumn slabs with bottom subwavelength nanostructures are implemented with a diameter of 1200 μm by a combination of self-assembly technique, silicon-on-insulator (SOI) technology, manufacturing of silicon, and epitaxial growth of GaN. Reflectance results experimentally show that optical reflection is greatly reduced by introducing the GaN nanocolumns and subwavelength nanostructures, and photoluminescence measurements demonstrate that the extracted light is significantly enhanced with the assistance of the low-index buffer layer and bottom subwavelength nanostructures.     

Plasmonic microcavity formed by the Möbius strip

We propose a Möbius-strip-type plasmonic cavity with a silver Möbius strip sandwiched between dielectric layers. By brief theoretical and simulation analyses, we obtain that the Q factor of the cavity remains about 40 and the mode volume is ultrasmall (less than 1 μm³) which is more compact than that of the cylindric cavity. This Möbius-strip-type plasmonic cavity supporting the propagation of surface plasmon polaritons owns some unusual properties such as more effective volume and the spatial separation. More potential applications based on this cavity remain to be explored in future nanophotonics.     

一种新型介质结构的超传输电磁特性研究

光入射到不同折射率材料的分界面时会很自然地产生反射现象. 在很多的工业应用中, 例如太阳能电池, 衬底的引入会在其表面产生反射损耗. 至今为止, 人们提出很多方法用来克服这一问题, 比较常见的有介质涂层、表面纹理、绝热折射率匹配和散射等离激元纳米粒子. 本文利用二维周期排布的亚波长级硅纳米圆柱阵列来降低衬底表面的反射. 结合辅助微分方程和时域有限差分法对该结构的散射特性进行系统研究, 结果发现, 纳米圆柱粒子能够产生类似于在金属表面发生的超传输现象, 这种现象的发生基于介质衬底耦合Mie共振机理, 该机理能在整个紫外到近红外光谱范围内将能量耦合到衬底中, 从而降低衬底表面的反射; 同时当散射结构被放置在具有高光学态密度的高折射率衬底附近时, 会产生较强的前向散射, 也能有效的减少后向散射即反射的发生. 基于降低衬底表面反射这一目的而言, 我们设计的结构可为实际太阳能电池及光学天线的设计提供参考.