银离子修饰的介孔磷钨酸/二氧化硅催化剂氧化脱硫性能研究

采用银修饰介孔磷钨酸/二氧化硅（mesoporous HPW/SiO₂）催化剂,并研究了其在模拟柴油和真实柴油氧化脱硫反应中的催化性能。通过银修饰介孔HPW/SiO₂,结合银离子对有机硫化物的选择吸附性和HPW对有机硫化物的催化氧化活性,以达到选择氧化脱硫的目的。模拟柴油分别采用石油醚、苯、1-辛烯和二苯并噻吩配制,当银离子与HPW的摩尔比为2时,催化剂具有最高的选择催化氧化活性。采用N₂ 吸附-脱附、XRD、UV-vis和EDS表征了银修饰的介孔HPW/SiO₂催化剂,结果表明,银物种分散均匀且以Ag⁺形式存在。真实柴油的脱硫研究表明,相比介孔HPW/SiO₂催化剂,修饰的催化剂介孔Ag₂-HPW/SiO₂脱硫率提高了4.6%,初始硫含量为1800×10^-6的直馏柴油能被脱除至228×10^-6,脱硫率为87.3%。介孔Ag₂-HPW/SiO₂催化剂具有良好的再生性能,经再生处理后,Ag的损失量极少,其三次脱硫率达到84.8%。     

Review of Ag/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Reductant System in the Selective Catalytic Reduction of NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

Ag/Al₂O₃ is a promising catalyst for the selective catalytic reduction (SCR) by hydrocarbons (HC) of NO _x in both laboratory and diesel engine bench tests. New developments of the HC-SCR of NO _x over a Ag/Al₂O₃ catalyst are reviewed, including the efficiencies and sulfur tolerances of different Ag/Al₂O₃-reductant systems for the SCR of NO _x ; the low-temperature activity improvement of H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃; and the application of a Ag/Al₂O₃-ethanol SCR system with a heavy-duty diesel engine. The discussions are focused on the reaction mechanisms of different Ag/Al₂O₃-reductant systems and H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃. A SO₂-resistant surface structure in situ synthesized on Ag/Al₂O₃ by using ethanol as a reductant is proposed based on the study of the sulfate formation. These results provide new insight into the design of a high-efficiency NO _x reduction system. The diesel engine bench test results showed that a Ag/Al₂O₃-ethanol system is promising for catalytic cleaning of NO _x in diesel exhaust.     

Nox reduction with CO over supported Pd catalysts under simulated post Euro-IV diesel exhaust conditions

The catalytic reduction of NO_x with CO over Pd/Al₂O₃ and Pd/TiO₂/Al₂O₃ under simulated post Euro-IV diesel exhaust conditions was studied. The catalytic activities obtained by using various Pd and TiO₂ loadings and total amounts of reductant and the influence of H₂ and H₂O was investigated.     

Kinetic Study on the Selective Oxidation of H2S Containing Excess Water and Ammonia

The selective oxidation of hydrogen sulfide containing excess water and ammonia was studied over V₂O₅/SiO₂ catalysts. H₂S was successfully converted to elemental sulfur and ammonium thiosulfate (ATS) without considerable emission of sulfur dioxide. Kinetic studies were carried out to describe the complex reaction paths. This revised version was published online in June 2006 with corrections to the Cover Date.     

A poly(ethylene glycol)-supported quaternary ammonium salt for highly efficient and environmentally friendly chemical fixation of CO2 with epoxides under supercritical conditions

A PEG-supported quaternary ammonium salt is proved to be an efficient and recyclable homogeneous catalyst for solvent-free synthesis of cyclic carbonates from carbon dioxide and epoxides under supercritical conditions. Supporting Bu₄NBr on soluble polymer PEG6000 enhances the catalytic activity. The workup procedure is straightforward, and the catalyst can be reused over five times with no appreciable loss of catalytic activity and selectivity.     

NH3-SCR脱硝催化剂抗硫性能的研究进展

氮氧化物(NO_x)是一种重要的大气污染物, 它造成严重的环境问题, 同时威胁人类健康. 以钢铁烧结烟气为代表的固定源和以柴油机尾气为代表的移动源是氮氧化物的主要来源. 氨气选择性催化还原法(NH₃-SCR)是目前最有效且应用最广泛的NO_x脱除技术. 然而, 无论是固定源还是移动源上NH₃-SCR催化剂, 都不可避免地会被SO₂毒化, 造成催化剂失活, 限制了NH₃-SCR技术的进一步应用. 因此, 研究NH₃-SCR催化剂的SO₂中毒机制以及提高催化剂的抗硫性能至关重要. 我们对固定源脱硝的金属氧化物和移动源上脱硝的Cu基分子筛这两类不同催化剂体系的SO₂中毒机制的研究进展进行了介绍, 并对这两种催化剂上提高抗硫性能改性方法的研究进展进行了评述, 为未来的研究提供了参考.     

SnS2纳米材料的水热合成及光催化性质

在不同的表面活性剂和硫源的条件下,采用水热法制备了多种形貌的SnS₂纳米材料,详细讨论了反应条件对其形貌和性质的影响,并采用X射线衍射(XRD)、扫描电镜(SEM)、和BET比表面积法对制备的样品的物相、形貌和组成进行了表征,通过光催化降解罗丹明B研究了所得样品的光催化性能。结果表明：表面活性剂和硫源对产物的结构和形貌起到了重要的作用。当Sn⁴⁺与表面活性剂的物质量的比为1：1时,样品均为纯的六方相SnS₂。采用柠檬酸三钠为表面活性剂、硫脲为硫源时制得的SnS₂纳米片具有最大的比表面积,同时表现出了最优的光催化性能。     

Microcalorimetric Studies of the Surface Reactivity of Pollutant Gas Atmospheres on Supported SnO2 and Ga2O3 Catalysts

The surface properties of gallium oxide and tin dioxide supported on alumina or titania have been studied by adsorption microcalorimetry. The differential heats of adsorption of various pollutant adsorbates such as sulfur dioxide, nitrogen monoxide, nitrogen dioxide and also ammonia were measured on these catalytic surfaces. NH₃, SO₂, NO₂ are strongly adsorbed while NO is only physisorbed. The supported Ga₂O₃ samples show a slight decrease in acidity as probed by ammonia adsorption, compared to alumina or titania. The addition of SnO₂ decreases the number of strong acid sites but creates a few weak and medium strength acid sites on alumina and does not modify the acidity of titania. In all cases, the basicity, probed by SO₂ adsorption, is very strongly affected by the deposition of Ga₂O₃ or SnO₂. The differential heats of NO₂ adsorption remain nearly constant on all samples. The heats of adsorption are discussed as a function of the coverage and of the amount of guest oxide. This revised version was published online in August 2006 with corrections to the Cover Date.     

CO2/N2-switchable viscoelastic fluids based on a pseudogemini surfactant system

We prepared a CO₂/N₂-switchable pseudogemini surfactant system composed of sodium oleate (NaOA) and N, N, N’, N’-tetramethyl-1, 6-hexanediamine (TMHDA) at a mole ratio of 2:1. The two tertiary amine groups of the TMHDA can be protonated into quaternary ammonium salt when the system was bubbled with CO₂, which can ‘‘bridge’’ two NaOA molecules via electrostatic attraction to form a pseudogemini surfactant. The formed pseudogemini surfactant can further self-assemble to wormlike micelles, causing a sharp increase in viscosity. The viscoelastic property and structure transitions of the pseudogemini surfactant system were investigated before and after bubbling of CO₂. The pseudogemini surfactant system transformed from water-like to gel-like fluid with the bubbling of CO₂, followed by white precipitate. The cryo-transmission electron microscope (cryo-TEM) characterization and rheological measurements exhibited that the sol–gel transition was attributed to a spherical-wormlike micelle transition. Moreover, this transition was switchable at least in three cycles. Finally, a reasonable mechanism of aggregate behavior transition was proposed from the viewpoint of the molecular states, micelle structures, and intermolecular interactions.     

Determination of sulfur contents of SO3, S2O3 and S based on the electrocatalytic interaction with homogeneous mediator tris(2,2'-bipyridyl)Ru(II)

A sensitive voltammetric method has been developed for the determination of total or single species of sulfur anions containing sulfide, sulfite and thiosulfate. The method is based on the catalytic effect of tris(2,2'-bipyridyl)Ruthenium(II) (Ru(bpy)₂^+ 2) as a homogeneous mediator on the oxidation of those anions at the surface of a glassy carbon electrode. A reversible redox couple of Ru(II)/Ru(III) were observed as a solute in aqueous solution. Cyclic voltammetry study showed that the catalytic current of the system depends on the concentration of the anions. Optimum pH values for voltammetric determination of sulfite, thiosulfate and sulfide has been found to be 5.6, 10.0 and 10.0, respectively. Under the optimized conditions the calibration curves have been obtained linear in the concentration ranges of 0.8–500.0, 0.4–1000.0 and 0.5–5000.0 µmol L^− 1 of SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The detection limits have been calculated to be 0.40, 0.17 and 0.33 µmol L^− 1 for SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The diffusion coefficients of sulfite and thiosulfate have been estimated using chronoamperometry. The chronoamperometric method also has been used to determine the catalytic rate constant for catalytic reaction of the Ru(bpy)₂^+ 2 with sulfite and thiosulfate. Finally the proposed method has been used for the determination of total sulfur contents in real samples of water and wastewater. Moreover the sulfite content in sugar and sulfur dioxide in air has been determined with satisfactory results.     

Ultra-low expansion glass from gels

Pyrolysis of mixed titanium and silicon metal halides produces a commercial glass (7.4% TiO₂) with ultra-low thermal expansion that is essentially zero over the temperature range of 0 to 300°C. A colloidal particulate gel process involving potassium silicate, titania sol and formamide gel reagent was found to produce glass compositions with similar low expansion behavior. Due to the strongly basic nature of the precursor solutions, special titania sols had to be prepared that were stable in these alkali silicate solutions. The preferred TiO₂ sols were those containing quaternary ammonium stabilizing counter-ions. These sols served not only as the source of homogeneously distributed titania, but they may also serve as nucleating species that contribute to particle growth and pore size control of the gel network. The large pore (0.3 µm) TiO₂/SiO₂ gel structures were easily dealkalized, dried and sintered to uncracked glass shapes. Plates up to 9.5 cm×6.6 cm× 0.5 cm thick and some intricate cast shapes were produced and their glass properties evaluated.     

一种多季胺阳离子诱导Bi2WO6片状团簇微球的合成及光致发光特性

以一种实验室自合成的双子季铵盐为表面活性剂,采用水热法,通过调节pH值,制备出由Bi2WO6纳米片自组装而成的不同片状团簇微球。研究了不同Bi2WO6片状团簇微球的物相结构、成分、晶体形貌和光致发光特性,探讨了其可能的生长机理。结果表明,在这种多季胺阳离子作用下,pH值对Bi2WO6片状团簇微球的物相、形貌和光致发光性能有明显的影响,随着pH值的增大,Bi2WO6片状团簇微球在(131)晶面处呈现明显的择优取向生长,在pH=5时,Bi2WO6微球可达到最大的发光强度。     

Promoter effect of nickel in thiophene hydrodesulfurization as monitored by sulfur uptake and cyclohexane conversion

Hydrodesulfurization (HDS) activity and activation energy (ε′_TH) values were determined and compared with irreversible sulfur uptake (S_irr) by 5 Al₂O₃-supported (MoO_x, Ni and three NiMoO_x) catalysts and, in unsulfided form with the cyclohexane conversion activity. Synergy between Ni and Mo in catalytic activity and a correlation between HDS activity and the amounts of S_irr was found. Some explanations for the differences in catalytic behavior of the different samples are presented.     

Preparation and Antibacterial Function of Quaternary Ammonium Salts Grafted Cellulose Fiber Initiated by Fe2 +-H2O2 Redox

The surface contact disinfecting technique is a newly developed method for water sterilization. In this paper, the grafted quaternary ammonium salts (QAS) antibacterial fibers were prepared and designed to apply for the surface contact disinfecting process in water treatment. The antibacterial fibers were directly prepared by grafting methacryloxylethyl benzyl dimethyl ammonium chloride (DMAE-BC) onto cellulose fiber using thiocarbonate-H₂O₂ redox system. All kinds of factors in the grafting reactions, such as reaction time, reaction temperature, monomer concentration, initiator concentration, which influence the percentage of grafting, were studied and optimized. The modified cellulose fibers were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscope(SEM). The effects of the percentage of grafting of the grafted cellulose fibers on bactericidal activity were also studied. The spread plate method was used to characterize the bactericidal activity. The disinfection process was further investigated by directly observing the morphology of the bacterial cells adsorbed on the antibacterial fibers with SEM and measuring extracelluar total protein concentration in suspension. The poly(DMAE-BC)-grafted cellulose ?ber was found to exhibit particularly high activity against E.coli.     

Improve the catalytic activity of α-Fe2O3 particles in decomposition of ammonium perchlorate by coating amorphous carbon on their surface

Sphere- and pod-like α-Fe₂O₃ particles have been selectively synthesized using NH₃·H₂O and NaOH solution to adjust the pH value of the designed synthetic system, respectively. The sphere-like α-Fe₂O₃ particles with diameter about 25 nm on average were encapsulated into carbon shells to fabricate a novel core-shell composite (α-Fe₂O₃@C) through the coating experiments. The catalytic performance of the products on the thermal decomposition of ammonium perchlorate (AP) was investigated by thermal gravimetric analyzer (TG) and differential thermal analysis (DTA). The thermal decomposition temperatures of AP in the presence of pod-like α-Fe₂O₃, sphere-like α-Fe₂O₃ and α-Fe₂O₃@C are reduced by 72, 81 and 109 °C, respectively, which show that α-Fe₂O₃@C core-shell composites have higher catalytic activity than that of α-Fe₂O₃.     

Ca2+-Mg2+-Zn2+体系在水溶性聚磷酸铵溶液中螯合规律的研究

近年来,水溶性聚磷酸铵在液体肥料和复合肥料的领域受到了广泛的关注,并在发达国家中得到了大面积的推广及应用。在pH值为5.5~8.0、温度为278.15 K~323.15 K的条件下,本文采用滴定法研究Ca_²⁺-Mg_²⁺-Zn_²⁺体系在聚磷酸铵溶液中的螯合规律。实验结果表明：相同质量分数的聚磷酸铵溶液对金属离子的螯合量会随着体系中Ca_²⁺、Mg_²⁺、Zn_²⁺的摩尔浓度的变化而变化;随着温度的升高而逐渐降低;随着pH的增加而逐渐增加;随着聚合度的升高而逐渐增加。采用傅里叶红外光谱对聚磷酸铵和A₁B₃C₃体系的螯合物进行表征。     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

铜物种对Cu/Fe2O3水煤气变换反应催化剂性能的影响

采用共沉淀法制备了系列铜负载量不同的Cu/Fe₂O₃水煤气变换(WGS)催化剂,并考察了铜负载量对催化剂结构和水煤气变换反应性能的影响. 结果表明,Cu/Fe₂O₃催化剂呈现出良好的水煤气反应性能,当CuO质量分数为20%时,催化剂的WGS性能最优,250 ℃时CO转化率高达97.2%,同时热稳定性也最好. 运用X射线粉末衍射(XRD)、N₂物理吸脱附和H₂程序升温还原(H₂-TPR)等手段对Cu/Fe₂O₃催化剂的物相、织构特征及还原性能进行了表征,结果表明,CuFe₂O₄物种的存在极大地改善了催化剂的还原性能和WGS反应活性. 这是由于CuFe₂O₄特殊的尖晶石结构有利于Cu微晶的稳定;同时,CuFe₂O₄在低温下即被还原为单质铜,有利于促进催化剂体系中电子的转移. 此外,通过(NH₄)₂CO₃溶液处理,研究了独立相CuO对Cu/Fe₂O₃催化剂WGS反应性能的影响,结果发现,独立相CuO的存在,有利于H原子在各组分传递,从而促进催化剂的CuFe₂O₄的还原,改善Cu/Fe₂O₃催化剂的WGS反应性能.     

Al含量对Pt-SO2-4 /ZrO2-Al2O3固体超强酸催化

通过向SO^2-₄ /ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和稳定性的Pt-SO^2-₄ /ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂性能的影响; 并采用X射线衍射(XRD)、比表面积测定(BET)、红外(IR)光谱、程序升温还原(TPR)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH₃-TPD)手段对催化剂进行了表征. 结果表明, Al能够提高ZrO₂的晶化温度, 抑制硫的分解, 增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃含量(质量分数, w)为5.0%时, Pt-SO^2-₄ /ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最好, 在100 h内异戊烷收率可稳定在52.0%以上, 选择性在98.2%以上.     

A Radioisotope Flow-Circulation Tracer Method for Determination of Sulfur Uptake and Exchange

A combined radioactive flow-circulation tracer method has been developed and applied to a CoMo/Al₂O₃ catalyst for measurement of sulfur uptakes and of catalyst - gas phase sulfur exchange in the H₂S partial pressure range of 2–47 kPa and the temperature range of 373–673 K. Equilibrium between gas-phase and catalyst sulfur species was rapidly achieved. A substantial part of the sulfur uptake was retained as adsorbed (reversible) sulfur species. The exchange of sulfur increased with increase in temperature up to 573 K and in H₂S partial pressure up to 4 kPa.