Growth and properties of air-processed GdBa2Cu3O7−δ superconductors with fined Gd2BaCuO5 and Gd2Ba4CuFeOy additions

We have succeeded in synthesizing a powder form of Gd₂Ba₄CuFeO_y (Gd2411) in air. GdBa₂Cu₃O_7−δ (Gd123)/Gd₂BaCuO₅ (Gd211) precursor powders added with different amounts of Gd₂Ba₄CuFeO_y (x = 0, 0.002, 0.004, 0.02) in molar ratio to Gd123 have been fabricated successfully into the form of large, single grains by the top seeded melt growth (TSMG) process. The relation between the additions amounts of Gd2411/Gd211 and critical current density (J_C) was analyzed. We found Gd2411 particles stably exist in the Gd123 matrix without degradation of superconducting properties owing to the existence of the Fe magnetic ion. The trapped field was observed to increase significantly compared with the bulk without Gd2411 additions.     

Superconductivity magnetism and low temperature specific heat in YBa2(Cu1−xFex)3O7−δ with δ0 and δ1

Magnetic and low temperature specific heat measurements have been performed on iron doped YBa₂(Cu_1−xFe_x)₃O_7−δ samples with different oxygen contents (δ0 and δ1). Iron doping induces an orthorhombic to tetragonal transition and a decrease of both T_c and diamagnetic signal. Low temperature specific heat measurements reveal a Schottky type anomaly for δ0 samples with x=0.01 (1.8 K) and x=0.02 (3 K). This anomaly is attributed to magnetic interactions within iron limited chains. A numerical analysis of this effect is proposed.     

Reduced anti-ferromagnetism promoted by Zn 3d substitution at CuO2 planar sites of Cu0.5Tl0.5Ba2Ca3Cu4O12−δ superconductors

The role of charge carriers in ZnO₂/CuO₂ planes of Cu_0.5Tl_0.5Ba₂Ca₃Cu_4−yZn_yO_12−δ material in bringing about superconductivity has been explained. Due to suppression of anti-ferromagnetic order with Zn 3d¹⁰ (S=0) substitution at Cu 3d⁹ sites in the inner CuO₂ planes of Cu_0.5Tl_0.5Ba₂Ca₃Cu₄O_12−δ superconductor, the distribution of charge carriers becomes homogeneous and optimum, which is evident from the enhanced superconductivity parameters. The decreased c-axis length with the increase of Zn doping improves interlayer coupling and hence the three dimensional (3D) conductivity in the unit cell is enhanced. Also the softening of phonon modes with the increased Zn doping indicates that the electron–phonon interaction has an essential role in the mechanism of high-T_c superconductivity in these compounds.     

Effect of Ca doping on the superconducting properties of GdBaSrCu3O7−δ bulk samples

Gd_1−xCa_xBaSrCu₃O_7−δ samples (0  x  0.1) were prepared via solid-state reaction. Four-point probes method was used for resistance versus temperature measurements. Results show decrease in T_c by increasing x content. This variation is assumed to be irrelevant to the different phases or impurity effects since X-ray patterns show all samples are tetragonal single-phase. Ca doping decreases the oxygen content and lattice parameters of the samples. It is suggested that Ca prevents the dislocation of oxygen, and then disrupts the hole concentration of the system and antiferromagnetic correlation at CuO₂ planes. Subsequently, destroys the superconductivity of the samples.     

Study of the superconducting transition in YBa2Cu3O7−δ single crystal by thermopower measurements

We have determined the superconducting transition in YBa₂Cu₃O_7−δ single crystal by measurements of thermopower. Two transitions were observed in both the ab-plane and the c-direction. The high temperature transition may have a close relation to the surface shell of the crystal.     

Synthesis, characterization and melt processing of Y1−x(Yb0.9Nd0.1)xBa2Cu3Oz superconductors

Effects of a combined substitute of Yb and Nd on Y site on the superconducting properties of YBa₂Cu₃O_y have been studied. We synthesized Y_1−x(Yb_0.9Nd_0.1)_xBa₂Cu₃O_z compound with x = 0.2, 0.4, 0.6, 0.8 and 1.0. Here, the ratio of Yb–Nd was fixed to be 9:1 for obtaining 123 phase without secondary phases. The melt processing thermal profiles for Y_1−x(Yb_0.9Nd_0.1)_xBa₂Cu₃O_z with x = 0.2 and 0.4 and the addition of 40 mol% {Y_1−x(Yb_0.9Nd_0.1)_x}₂BaCuO₅ and 0.5 wt% Pt in air were determined on the basis of the thermal analysis results. All samples showed a low grain growth rate, particularly for high x values, which may be partially ascribed to un-optimized thermal schedules. Although almost all the samples exhibited low J_c values, the sample with x = 0.2 exhibited T_c of 88.8 K and a relatively high J_c value of 16,000 A/cm² at 77 K for H//c-axis.     

Fabrication of NdBa2Cu3O7−δ single crystals by the top-seeded solution-growth method in 1%, 21%, and 100% oxygen partial pressure atmosphere

Single crystals of NdBa₂Cu₃O_7−δ (Nd123) have been successfully grown by the top-seeded solution-growth (TSSG) method in 1%, 21% and 100% oxygen partial pressure atmosphere ((P(O₂) = 0.01 atm, P(O)₂) = 0.21 atm and P(O₂) = 1.00 atm). Ba---Cu---O solvent with a Ba to Cu ratio of 3:5 was used in a Nd₂O₃ crucible. Nd is supplied by the reaction between the molten solvent and the Nd₂O₃ crucible. Compositions of Nd123 single crystals grown in different oxygen partial pressure atmospheres were analyzed by inductivity coupled plasma atomic emission spectrometry (ICP-AES) and confirmed to be Nd:Ba:Cu = 1.01:1.97:3.00 for P(O₂) = 0.01 atm, Nd:Ba:Cu = 1.07:1.95:3.00 for P(O₂) = 0.21 atm and Nd:Ba:Cu = 1.10:1.90:3.00 for P(O₂) = 1.00 atm, respectively. The Nd123 single crystals grown in different oxygen partial pressure atmospheres were annealed in a pure oxygen gas flow, and the temperature dependence of the DC magnetization for these crystals was measured using a superconducting quantum interference device (SQUID) magnetometer. The Nd123 single crystal grown in P(O₂) = 0.01 atm, and annealed at 340°C for 200 h showed a steep superconductive transition at 96 K. On the other hand, the Nd123 crystal grown in P(O₂) = 0.21, 1.00 atm and, annealed at 340°C for 200 h exhibited a broad transition at 92 K for P(O₂) = 0.21 atm and at 88 K for P(O₂) = 1.00 atm, respectively. Therefore for Nd123 single crystal production with high quality superconductive characteristics, a low oxygen partial pressure atmosphere during crystal growth is found to be effective for minimizing the substitution of Nd ions into Ba sites.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Two models for the transport properties of YBa2Cu3O7−δ in its normal state

The high-temperature superconductor YBa₂Cu₃O_7−δ in its normal state, shows unusual dependence of its transport properties on the oxygen deficiency parameter δ and on temperature: for δ ≈ 0 both the resistivity and the Hall number rise linearly with temperature, while the thermoelectric power is very small. In order to interpret this unusual combination of properties we propose two alternative models, a two-dimensional tight-binding wide-band model, and a narrow-band model. In the first case we assume scattering by a fully excited boson field, with a mean free path Λ ∝ 1/T. In the second model we assume a band composed of two parts, where the upper smaller part does not contribute to transport (as would result from the existence of a mobility edge), and Λ is independent of temperature. The calculated results are compared with experiments.     

Effect of BiFeO3 addition on Bi2O3–ZnO–Nb2O5 based ceramics

In this paper, low temperature sintering of the Bi₂(Zn_1/3Nb_2/3)₂O₇ (β-BZN) dielectric ceramics was studied with the use of BiFeO₃ as a sintering aid. The effects of BiFeO₃ contents and the sintering temperature on the phase structure, density and dielectric properties were investigated. The results showed that the sintering temperature could be decreased and the dielectric properties could be retained by the addition of BiFeO₃. The structure of BiFeO₃ doped β-BZN was still the monoclinic pyrochlore phase. The sintering temperature of BiFeO₃ doped β-BZN ceramics was reduced from 1000 °C to 920 °C. In the case of 0.15 wt.% BiFeO₃ addition, the β-BZN ceramics sintered at 920 °C exhibited good dielectric properties, which were listed as follows: ε_r = 79 and tan δ = 0.00086 at a frequency of 1 MHz. The obtained properties make this composition to be a good candidate for the LTCC application.     

Defect chemical and statistical thermodynamic studies on oxygen nonstoichiometric Nd2 − xSrxNiO4 + δ

In order to elucidate how oxygen content changes in Nd_2 − xSr_xNiO_4 + δ (x = 0, 0.2, 0.4), defect chemical and statistical thermodynamic analyses were carried out. The relationship among δ, P(O₂), and T were analyzed by a defect equilibrium model. Since Nd_2 − xSr_xNiO_4 + δ shows metal like band conduction at high temperatures, chemical potential of hole is expressed by the integration of the Fermi-Dirac distribution function and the density of state. The nonstoichiometric variation of oxygen content in Nd_2 − xSr_xNiO_4 + δ can be explained by the defect equilibrium model with a regular solution approximation. Partial molar entropy and partial molar enthalpy of oxygen are calculated from the nonstoichiometric data and Gibbs–Helmholtz equation. The relationship among defect structure, defect equilibrium, and thermodynamic quantities is elucidated by the statistical thermodynamic model. Thermodynamic quantities are calculated by the statistical thermodynamic model with the results of defect chemical analysis and compared with those obtained from experimental results. Thermodynamic quantities calculated by the statistical thermodynamic model can explain rough tendency of those obtained from the δ–T–P(O₂) relationship.     

The Fe3O4 origin of the “Biphase” reconstruction on α-Fe2O3(0 0 0 1)

The so-called Biphase termination on α-Fe₂O₃ has been widely accepted to be a structure with a 40 Å unit supercell composed of coexisting islands of Fe_1−xO and α-Fe₂O₃. Based on thermodynamic arguments and experimental evidence, including transmission electron diffraction, imaging, magnetic and spectroscopic information, it is found that the previously proposed structure model is inaccurate. The actual Biphase structure is instead a layered structure related to the reduction of α-Fe₂O₃ to Fe₃O₄. A model for the Biphase termination is proposed which does not contain islands of Fe_1−xO but instead consists of bulk α-Fe₂O₃ and a Fe₃O₄-derived overlayer. The proposed model is consistent with all current and previously reported experimental findings.     

Thermogalvanic power and fast ion conduction in δ-Bi2O3 and δ-(Bi2O3)1−x(R2O3)x with R = Y, Tb---Lu

The thermogalvanic power (Seebeck coefficient) of O^2- conducting δ-Bi₂O₃ and δ-(Bi₂O₃)_1−x(Y₂O₃)_x has been measured directly as a function of temperature and partial oxygen pressure in N₂---O₂ mixtures. The of δ-(Bi₂O₃)_0.75(R₂O₃)_0.25 with R = Tb---Lu was indirectly determined using an isothermal concentration cell technique. Except for pure δ-Bi₂O₃, the heat of transport is much smaller than the activation energy for O^2- conduction for all materials. The vibrational freedom of O²⁻ ions in all δ-stabilized materials is reflected in their IR spectra at room temperature. Two prototypes of a thermogalvanic P_O2 meter were tested.     

Oxygen nonstoichiometry of Sr(Co,Fe)O3−δ-based perovskites: I. Coulometric titration of SrCo0.85Fe0.10Cr0.05O3−δ by the two-electrode technique

The p(O₂)–T–δ diagram of perovskite-type SrCo_0.85Fe_0.10Cr_0.05O_3−δ was determined by the coulometric titration technique in the temperature range 770–1250 K at oxygen partial pressures from 8 10⁻¹⁰ to 0.5 atm. Stability of the cubic perovskite phase of SrCo_0.85Fe_0.10Cr_0.05O_3−δ, existing down to the oxygen pressures of 10⁻³–10⁻⁵ atm, was found to be slightly higher than that of SrCo_0.80Fe_0.20O_3−δ, probably due to stabilization of oxygen octahedra neighboring Cr⁴⁺ cations. When the oxygen nonstoichiometry of the Cr-containing perovskite decreases from 0.47 to 0.38, the partial molar enthalpy and entropy for overall oxygen incorporation reaction vary in the ranges −165 to −60 kJ mol⁻¹ and 90 to 150 J mol⁻¹ K⁻¹, respectively. Within the stability limits of the single perovskite phase, the p(O₂)–T–δ diagram can be adequately described by equilibrium processes of oxygen incorporation, cobalt disproportionation and interaction of cobalt and iron cations, with the thermodynamic functions independent of defect concentrations. Increasing grain size in SrCo_0.85Fe_0.10Cr_0.05O_3−δ ceramics from submicron size to 100–200 μm has no effect on the oxygen thermodynamics. The two-electrode coulometric titration technique, based on the alternate use of electrodes for oxygen pumping and e.m.f. measurements, is described and verified by studying oxygen nonstoichiometry of La_0.3Sr_0.7CoO_3−δ and PrO_x.     

Electrical characteristics and low-temperature sintering of BiFeO3-modified Pb(Zr,Ti)O3–Pb(Fe2/3W1/3)O3–Pb(Mn1/3Nb2/3)O3 ceramics with ZnO addition

Effects of ZnO addition on electrical properties and low-temperature sintering of BiFeO₃-modified Pb(Zr,Ti)O₃–Pb(Fe_2/3W_1/3)O₃–Pb(Mn_1/3Nb_2/3)O₃ were investigated. The investigations revealed that the sintering temperature can be decreased to 950 °C, and the favorable properties were obtained with 0.10 wt% ZnO added ceramics. The electrical properties were as follows: d₃₃ = 313 pC/N, K_p = 0.56, tan δ = 0.0053, ε_r = 1407 and T_c = 295 °C, which showed that this system was a promising material for the multilayer devices application.     

High-resolution infrared study of the 2ν3 (A1, E) and ν1 + ν3 (E) bands of NF3

The 2ν₃ overtone (A₁, E) and the ν₁ + ν₃ (E) combination bands of the oblate symmetric top ¹⁴NF₃ were studied by FTIR spectroscopy with a resolution of 2.5 × 10⁻³ cm⁻¹. Nearly 500 lines up to K_max/J_max = 30/43 were observed for the weak A₁ component reaching the v₃ = 2⁰ substate (1803.1302 cm⁻¹), the majority of which corresponded to reinforced K = 3p-type transitions. For the strong E component reaching the v₃ = 2^±2 substate (1810.4239 cm⁻¹), about 3550 transitions were assigned up to K_max/J_max = 65/69, favoring a clear observation of the ℓ(4, −2) and ℓ(4, 4) splittings within the kℓ = −2 and +4 sublevels, respectively. The two v₃ = 2 substates are linked by the ℓ(2, 2)- and ℓ(2, −1)-type interactions, providing severe crossings, respectively, at K′ = 6 and near K′ = 24 on the v₃ = 2⁺² side. A model working in the D-reduction and including all these ℓ-type interactions could reproduce together 3695 nonzero weighted experimental data (NZW) through 33 free parameters with a standard deviation of σ = 0.357 × 10⁻³  cm⁻¹. As for the ν₁ + ν₃ (E) combination band, about 3690 lines were assigned up to K_max/J_max = 45/55. Its v₁ = v₃ = 1 upper state (1931.577 5 cm⁻¹) was treated using the same model recently applied to the v₃ = 1 (E, 907.5413 cm⁻¹) state. It yielded 21 free parameters through 3282 NZW experimental data, adjusted with σ = 0.344 × 10⁻³  cm⁻¹ in the D-reduction. For the two excited states, the small and unobserved ℓ(0, 6) interaction was tested as useless. To confirm the adequacy of the vibrationally isolated models used, some other reductions of the Hamiltonian were tried. For the v₃ = 2 state, the D-, L-, and LD-reductions led to similar σ’s, while the Q one was not successful. For the v₁ = v₃ = 1 state, the D- and Q-reductions gave comparable σ’s, while the QD-reduction was not as good. The corresponding unitary equivalence relations are generally more nicely fulfilled for the v₃ = 2 state than for the v₁ = v₃ = 1 state. The three derivable anharmonicity constants in cm⁻¹ are x₃₃ = −4.1528, g₃₃ = +1.8235 and x₁₃ = −7.9652.     

Preparation and characterization of Y1−xPrxBa2Cu3O7−δ single crystals

We present a reliable method for growing single crystals of Y_1−xPr_xBa₂Cu₃O_7−δ high-T_c superconductors in ZrO₂ crucibles. This method results in crystals with greatly improved superconducting properties compared to crystals grown with the previously reported methods which use Al₂O₃ crucibles. We describe techniques for crystal growth in both Al₂O₃ and ZrO₂ crucibles using an excess of BaCo₃ and CuO as the flux. The crystals were characterized by means of DC magnetic-susceptibility measurements, electrical-resistivity measurements, and electron microprobe analysis. The effects of Al contamination on the conditions for crystal growth and on the superconducting properties of the crystals are found to be quite significant.     

Defect chemistry and oxygen transport of (La0.6Sr0.4 − xMx)0.99Co0.2Fe0.8O3 − δ, M = Ca (x = 0.05, 0.1), Ba (x = 0.1, 0.2), Sr: Part I: Defect chemistry

This paper is the first part of a two part series, where the effects of varying the A-site dopant on the defect chemistry, the diffusion coefficient and the surface catalytic properties of the materials (La_0.6Sr_0.4 − xM_x)_0.99Co_0.2Fe_0.8O_3 − δ, M = Sr, Ca (x = 0.05, 0.1), Ba (x = 0.1, 0.2) (LSMFC) have been investigated. In part I, the findings on the defect chemistry are reported, while the transport properties are reported in part II. Substitution of Sr²⁺ ions with Ca²⁺ ions (smaller ionic radius) and Ba²⁺ ions (larger ionic radius) strains the crystal structure differently for each composition while keeping the average valence of the cations constant. The Ba²⁺ containing materials show the largest oxygen loss at elevated temperatures, while the purely Sr²⁺ doped material showed the smallest oxygen loss. This was reflected in the partial oxidation entropy of the materials. The measured oxygen loss was modelled with point defect chemistry models. Measurements at very low p_O2 showed several phase transitions.     

A new method to preserve the c-axis growth of thick YBa2Cu3O7–δ films grown by pulsed laser deposition

YBa₂Cu₃O_7–δ (YBCO) films were prepared on (1 0 0) MgO substrates by pulsed laser deposition (PLD) method. In order to eliminate the a-axis growth, which is commonly observed in the YBCO film thicker than a critical value, we developed a new PLD target that was sintered at a temperature far below YBCO 123 phase formation. The surface analysis made by AFM technique confirmed that very fine particles of around 20 nm size could be ejected from the new target to the substrate. The fine oxide clusters could be easily moved and incorporated into the YBCO phase thus benefited the c-axis growth even in the thick films. For instance, only the c-axis growth in the new film with a thickness of about 650 nm was larger than a critical thickness of the a-axis growth. However, in the standard film of the same thickness, there is 24.5% of the a-axis growth accompanying the main c-axis growth. Therefore, the c-axis growth could be preserved in the very thick YBCO film by a non-superconducting target.     

Water incorporation into the Ba2(In1 − xMx)2O5‪ (M = Sc 0 ≤ x < 0.5 and M = Y 0 ≤ x < 0.35) system and protonic conduction

Ba₂(In_1 − xM_x)₂O_{5 − y / 2}(OH)_y‪□_{1 − y / 2} (y ≤ 2; M = Sc³⁺ 0 ≤ x < 0.5 and M = Y³⁺ 0 ≤ x < 0.35) compounds were prepared by reacting Ba₂(In_1 − xM_x)₂O₅‪ phases with water vapor. This reaction is reversible. Analyses of the hydration process by TG and XRD studies show that the thermal stability of hydrated phases increases when x increases and that the incorporation of water is not a single-phase reaction inducing either a crystal system or space group modification. Fully hydrated (y = 2) and dehydrated (y = 0) samples have been stabilized at room temperature and characterized for all compositions. In wet air, all phases show a proton contribution to the total conductivity at temperatures between 350 and 600 °C. At a given temperature, proton conductivity increases with the substitution ratio and reaches at 350 °C, 5.4 10^− 3 S cm^− 1 for Ba₂(In_0.65Sc_0.35)₂O_4.2□_0.2(OH)_1.6.