Photoluminescence investigation of ferromagnetic Ga1−xMnxN layers with GaN templates grown on sapphire (0 0 0 1) substrates

We have investigated the temperature and composition dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x ≈ 0.1-0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. The efficient PL is peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. The band-gap energy of the Ga_1−xMn_xN layers decreased with increasing temperature and manganese composition. The band-gap energy of the Ga_1−xMn_xN layers was modeled by the Varshni equation and the parameters were determined to be α = 2.3 × 10⁻⁴, 2.7 × 10⁻⁴, 3.4 × 10⁻⁴ eV/K and β = 210, 210, and 230 K for the manganese composition x = 0.1%, 0.2%, and 0.8%, respectively. As the Mn concentration in the Ga_1−xMn_xN layers increased, the temperature dependence of the band-gap energy was clearly reduced.     

Conductivity and sintering property of LaNi1 − xFexO3 ceramics prepared by Pechini method

Preparation of LaNi_1 − xFe_xO₃, which is one of the candidate materials of solid oxide fuel cell cathode, current collecting layer and interconnect coating was examined with Pechini method and solid state reaction method. Single phase LaNi_1 − xFe_xO₃ with large Ni content has successfully been prepared by low temperature sintering as 750 °C with Pechini method, whereas large amount of raw materials has remained with solid state reaction method by sintering at the same temperature. It can be ascribed to more homogenous cation distribution in raw powder material prior to sintering with Pechini method. It has also been revealed that LaNi_1 − xFe_xO₃ with x lower than 0.3 is thermodynamically unstable in air above 1000 °C. LaNi_0.6Fe_0.4O₃ showed superior property as cathode material with high electrical conductivity, thermodynamic stability and appropriate sintering property.     

Alloy formation of Co/Ni/Pt(1 1 1)

The initial growth and alloy formation of ultrathin Co films deposited on 1 ML Ni/Pt(1 1 1) were investigated by Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and ultraviolet photoelectron spectroscopy (UPS). A sequence of samples of d_Co Co/1 ML Ni/Pt(1 1 1) (d_Co = 1, 2, and 3 ML) were prepared at room temperature, and then heated up to investigate the diffusion process. The Co and Ni atoms intermix at lower annealing temperature, and Co-Ni intermixing layer diffuses into the Pt substrate to form Ni-Co-Pt alloys at higher annealing temperature. The diffusion temperatures are Co coverage dependent. The evolution of UPS with annealing temperatures also shows the formation of surface alloys. Some interesting LEED patterns of 1 ML Co/1 ML Ni/Pt(1 1 1) show the formation of ordered alloys at different annealing temperature ranges. Further studies in the Curie temperature and concentration analysis, show that the ordered alloys corresponding to different LEED patterns are Ni_xCo_1−xPt and Ni_xCo_1−xPt₃. The relationship between the interface structure and magnetic properties was investigated.     

Effect of Ni interlayer on stress level of CoSi2 films in Co/Ni/Si(1 0 0) bi-layered system

The effect of Ni interlayer on stress level of cobalt silicides was investigated. The X-ray diffraction patterns (XRD) show that low temperature formation of Co_1−xNi_xSi₂ solid solution was obtained while Ni interlayer was present in Co/Si system, which was confirmed by Auger electron spectrum (AES) and sheet resistance measurement. XRD was also used to measure the internal stress in CoSi₂ films by a 2θ_ψ − sin²ψ method. The result shows that the tensile stress in CoSi₂ films evidently decreased in Co/Ni/Si(1 0 0) system. The reduction of lattice mismatch, due to the presence of Ni in Co_xNi_1−xSi₂ solid solution, is proposed to explain this phenomenon.     

Depth-dependent fct to fcc strain relaxation in CoxNi1−x/Cu3Au(1 0 0) alloy films

Co_xNi_1−x/Cu₃Au(1 0 0) with x ? 11% was prepared at room temperature to study the strain relaxation and their correlation with the spin-reorientation transition. The vertical interlayer distance relaxed from 1.66 Å (fct) to 1.76 Å (fcc) while the thickness increased from 8 ML to 18 ML. Such rapid strain relaxation with thickness was attributed to the larger lattice mismatch between Co_xNi_1−x and Cu₃Au(1 0 0) (η ∼ −6.5%). The smooth change for crystalline structure was observed during strain relaxation process in which the crystalline structure seems irrespective of the alloy composition. To explain the strain relaxation, a phenomenological model was proposed. We provide a physical picture that the deeper layers may not relax while the surface layer start to relax. This assumption is based on the several experimental studies. Using the strain averaged from all layers of thin film as the volume strain of magneto-elastic anisotropy energy, the interrelation between strain relaxation and spin reorientation transition can be well described in a Néel type magneto-elastic model.     

Surface defect states of CdTexS1 − x quantum dots

Properties of surface defect states of CdTe_xS_1 − x quantum dots with an average diameter of 7 nm are investigated experimentally. The stoichiometric ratio is found to be for by use of the energy dispersive analysis of x-ray. The photoluminescence spectrum, the photoluminescence excitation spectrum, and the surface passivation are adopted to characterize the properties of surface defect states. The energy levels of surface defect states of CdTe_xS_1 − x quantum dots are also determined.     

Temperature-programmed surface reaction (TPSR) of CH4 synthesis by PdxNi100−x nanoparticles

A series of Pd_xNi_100−x nanoparticles were prepared by the co-precipitation method and analyzed using a temperature-programmed surface reaction (TPSR) of their methanation reactions. ESCA measurement suggested that the as-prepared Pd-Ni alloys had Pd-core/Ni-shell structure. Surface Pd segregation occurred during H₂ reduction and resulted in a surface composition close to the nominal value. The TPSR experiments were performed by pre-adsorption of CO with H₂ to form methane. The peak temperature of methanation increased as Pd content increased, indicating that a methanation reaction is favored on Ni and Ni-rich alloy nanoparticles. For physical mixtures of Pd and Ni nanoparticles, methanation behaviors is similar to those of alloy nanoparticles; but the methanation temperatures of physical mixtures are always higher than those of alloy nanoparticles. This may be due to the formation of a Pd-enriched alloy surface layer during reduction in H₂ at 400 °C, or because the CO molecules adsorbed on the Pd sites spill over onto the Ni sites for methanation. Using TPSR technique and measuring methanation temperature, the top-most surface of such bimetallic nanoparticles can be probed.     

RAIRS studies of CO adsorption on Pd/CeO2−x(1 1 1)/Pt(1 1 1)

Reflection absorption infrared spectroscopy (RAIRS) has been used to investigate the adsorption of CO on CeO_2−x-supported Pd nanoparticles at room temperature. The results show that when CeO_2−x is initially grown on Pt(1 1 1), a small proportion of the surface remains as bare Pt sites. However, when Pd is deposited onto CeO_2−x/Pt(1 1 1), most of the Pd grows directly on top of the CeO_2−x(1 1 1). RAIR spectra of CO adsorption on 1 ML Pd/CeO_2−x/Pt(1 1 1) show a broad CO-Pd band, which is inconsistent with a single crystal Pd surface. However, the 5 ML and 10 ML Pd/CeO_2−x/Pt(1 1 1) spectra show vibrational bands consistent with the presence of Pd(1 1 1) and (1 0 0) faces, suggesting the growth of Pd nanostructures with well defined facets.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

The magnetic map of NiMn alloy thin films on Co(0 0 1) and Co(1 1 1)

Following the experimental work of Groudeva-Zotova et al. [S. Groudeva-Zotova, D. Elefant, R. Kaltofen, D. Tietjen, J. Thomas, V. Hoffmann, C.M. Schneider, J. Magn. Magn. Mater. 263 (2003) 57] where the magnetic and structural characteristics of a bi-layer NiMn-Co exchange biasing systems was investigated, density functional calculations with generalized gradient corrections were performed on (Mn_0.5Ni_0.5)_n ordered alloy on Co(0 0 1) and one Mn_1−xNi_x monolayer on Co(1 1 1). For the Mn_0.5Ni_0.5 monolayer on Co(0 0 1), magnetic moments per surface atom of 0.65 μ_B and 3.76 μ_B were obtained for Ni and Mn, respectively. Those magnetic moments are aligned parallel to the total moment of Co(0 0 1). A complex behavior of the Mn moment in dependence of the thickness “n” is obtained for (Mn_0.5Ni_0.5)_n on Co(0 0 1). Investigations on Mn_1−xNi_x monolayer on Co(1 1 1) have shown that the crystallographic orientation does not modify significantly neither the magnetic moments of Mn and Ni atoms nor their ferromagnetic coupling with the Co(1 1 1) substrate, except for x = 0.66. For x = 0.66 the Mn sub-lattice presents an antiferromagnetic coupling leading to a quenching of the Ni magnetic moment.     

Adsorption and photocatalytic degradation of methylene blue on Zn1−xCuxS nanoparticles prepared by a simple green method

Nanoparticles of Zn_1−xCu_xS with various dopant contents (0 ≤ x ≤ 0.15) were prepared in water by refluxing for 90 min at about 95 °C. Powder X-ray diffraction (XRD) patterns of the nanoparticles demonstrate that loading of Cu²⁺ ions does not change the crystal structure of ZnS. Scanning electron microscopy (SEM) images demonstrate that size of the nanoparticles decreases with increasing Cu²⁺ ions. UV-Vis diffuse reflectance spectra (DRS) of the nanoparticles show significant absorption in visible light region. Adsorption capacity of the nanoparticles for methylene blue (MB) increases with mole fraction of copper ions. Photocatalytic activity of the nanoparticles toward photodegradation of MB was evaluated under visible light irradiation. The results indicate that Zn_0.85Cu_0.15S nanoparticles exhibit highest photocatalytic activity among the prepared samples. Moreover, effects of refluxing time applied for preparation of the nanoparticles and calcination temperature were investigated.     

Mössbauer spectroscopy and magnetic properties in thin films of FexNi100−x electroplated on silicon (1 0 0)

Fe_xNi_100−x thin films were produced by galvanostatic electrodeposition on Si (1 0 0), nominal thickness 2800 nm, and x ranging 7-20. The crystalline structure of the sample was determined by X-ray diffraction (XRD). The magnetic properties were investigated by vibration sample magnetometry (VSM) and room temperature ⁵⁷Fe Mössbauer spectroscopy. Conversion Electron Mössbauer spectroscopy (CEMS) in both film surfaces for the thick self-supported films showed that the magnetic moment direction is in the plane and conventional transmission (MS) that the directions are out of the plane films. The results were interpreted assuming a three-layer model where the external layer has in-plane magnetization and the internal one, out of plane magnetization.     

High-temperature electrical properties of magnesiowustite Mg1 − xFexO and spinel Fe3 − x − yMgxCryO4 ceramics

Phase relationships, thermal expansion and electrical properties of Mg_1 − xFe_xO (x = 0.1-0.45) cubic solid solutions and Fe_{3 − x − y}Mg_xCr_yO_4 ± δ (x = 0.7-0.95; y = 0 or 0.5) spinels were studied at 300-1770 K in the oxygen partial pressure range from 10 Pa to 21 kPa. Increasing iron content enlarges the spinel phase stability domain at reduced oxygen pressures and elevated temperatures. The total conductivity of the spinel ceramics is predominantly n-type electronic and is essentially p(O₂)-independent within the stability domain. The computer simulations using molecular dynamics technique confirmed that overall level of ion diffusion remains low even at high temperatures close to the melting point. Temperature dependencies of the total conductivity in air exhibit a complex behavior associated with changing the dominant defect-chemistry mechanism from prevailing formation of the interstitial cations above 1370-1470 K to the generation of cation vacancies at lower temperatures, and with kinetically frozen cation redistribution in spinel lattice below 700-800 K. The average thermal expansion coefficients of the spinel ceramics calculated from dilatometric data in air vary in the range (9.6-10.0) × 10^− 6 K^− 1 at 300-500 K and (13.2-16.1) × 10^− 6 K^− 1 at 1050-1370 K. Mg_1 − xFe_xO solid solutions undergo partial decomposition on heating under oxidizing and mildly reducing conditions, resulting in the segregation of spinel phase and conductivity decrease.     

Scanning tunneling microscopy observation of initial growth of Sn and Ge1−xSnx layers on Ge(0 0 1) substrates

We have investigated the initial growth of Sn and Ge_1−xSn_x layers on Ge(0 0 1) surface by using scanning tunneling microscopy. After the growth of a 0.035 ML-thick Sn layer at room temperature, Sn clusters lining vertically to a dimer row was observed. In the case of the 0.035-0.018 ML-thick Sn growth at 250 °C, the characteristic surface reconstruction with the step-edge undulation like a comb was observed. In the growth of a Ge_0.994Sn_0.006 layer at 250 °C, the multilayer polynuclear growth with a lot of two-dimensional small domain was observed. These surface reconstructions should be accounted for by the large compressive stress induced in the surface layer due to the incorporation of Sn atoms.     

Effect of electric field on electrocaloric effect in Pb(Zr1 − xTix)O3 solid solution

A thermodynamic analysis is employed to investigate the intrinsic electrocaloric effect of Pb(Zr_1 − xTi_x)O₃ solid solution system under the different electric field. Theoretical analysis indicates that Pb(Zr_1 − xTi_x)O₃ system has the giant electrocaloric coefficient and the large adiabatic temperature change near its ferroelectric Curie temperature. The applied electric field decreases not only the electrocaloric coefficient but also its temperature dependence. Furthermore, it increases the adiabatic temperature change as well as its dependence of temperature. The temperature corresponding to the maximum of electrocaloric coefficient and adiabatic temperature change increases with the enhancement of electric field because of its first-order phase transition between ferroelectric phase and paraelectric phase.     

A density functional theory study of ethylene adsorption on Ni10(1 1 1), Ni13(1 0 0) and Ni10(1 1 0) surface cluster models and Ni13 nanocluster

Ethylene adsorption was studied by use of DFT/B3LYP with basis set 6-31G(d,p) in Gaussian’03 software. It was found that ethylene has adsorbed molecularly on all clusters with π adsorption mode. Relative energy values were calculated to be −50.86 kcal/mol, −20.48 kcal/mol, −32.44 kcal/mol and −39.27 kcal/mol for Ni₁₃ nanocluster, Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) surface cluster models, respectively. Ethylene adsorption energy is inversely proportional to Ni coordination number when Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) cluster models and Ni₁₃ nanocluster are compared with each other.     

Infrared reflection absorption spectral study for CO adsorption on Pd/Pt(1 1 1) bimetallic surfaces

Infrared reflection absorption spectroscopy (IRRAS) was used to investigate carbon monoxide (CO) adsorption on 0.15 nm-thick-0.6 nm-thick Pd-deposited Pt(1 1 1) bimetallic surfaces: Pd_x/Pt(1 1 1) (where x is the Pd thickness in nanometers) fabricated using molecular beam epitaxial method at substrate temperatures of 343 K, 473 K, and 673 K. Reflection high-energy electron diffraction (RHEED) measurements for Pd_0.15-0.6 nm/Pt(1 1 1) surfaces fabricated at 343 K showed that Pd grows epitaxially on a clean Pt(1 1 1), having an almost identical lattice constant of Pt(1 1 1). The 1.0 L CO exposure to the clean Pt(1 1 1) at room temperature yielded linearly bonded and bridge-bonded CO-Pt bands at 2093 and 1855 cm⁻¹. The CO-Pt band intensities for the CO-exposed Pd_x/Pt(1 1 1) surfaces decreased with increasing Pd thickness. For Pd_0.3 nm/Pt(1 1 1) deposited at 343 K, the 1933 cm⁻¹ band caused by bridge-bonded CO-Pd enhanced the spectral intensity. The linear-bonded CO-Pt band (2090 cm⁻¹) almost disappeared and the bridge-bonded CO-Pd band dominated the spectra for Pd_0.6 nm/Pt(1 1 1). With increasing substrate temperature during the Pd depositions, the relative band intensities of the CO-Pt/CO-Pd increased. For the Pd_0.3 nm/Pt(1 1 1) deposited at 673 K, the linear-bonded CO-Pt and bridge-bonded CO-Pd bands are located respectively at 2071 and 1928 cm⁻¹. The temperature-programmed desorption (TPD) spectrum for the 673 K-deposited Pd_0.3 nm/Pt(1 1 1) showed that a desorption signal for the adsorbed CO on the Pt sites decreased in intensity and shifted ca. 20 K to a lower temperature than those for the clean Pt(1 1 1). We discuss the CO adsorption behavior on well-defined Pd-deposited Pt(1 1 1) bimetallic surfaces.     

AlN, GaN, AlxGa1 − xN nanotubes and GaN/AlxGa1 − xN nanotube heterojunctions

Semiconductor optoelectronic devices based on GaN and on InGaN or AlGaN alloys and superlattices can operate in a wide range of wavelengths, from far infrared to near ultraviolet region. The efficiency of these devices could be enhanced by shrinking the size and increasing the density of the semiconductor components. Nanostructured materials are natural candidates to fulfill these requirements. Here we use the density functional theory to study the electronic and structural properties of (10,0) GaN, AlN, Al_xGa_1 − xN nanotubes and GaN/Al_xGa_1 − xN heterojunctions, 0<x<1. The Al_xGa_1 − xN nanotubes exhibit direct band gaps for the whole range of Al compositions, with band gaps varying from 3.45 to 4.85 eV, and a negative band gap bowing coefficient of −0.14 eV. The GaN/Al_xGa_1 − xN nanotube heterojunctions show a type-I band alignment, with the valence band offsets showing a non-linear dependence with the Al content in the nanotube alloy. The results show the possibility of engineering the band gaps and band offsets of these III-nitrides nanotubes by alloying on the cation sites.     

Structural studies of evaporated CoxCr1−x/Si (1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si (1 0 0) and glass substrates. Chemical composition and interface properties have been studied by modelling Rutherford backscattering spectra (RBS) using SIMNRA programme. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Simulation of the energy spectra shows an interdiffusion profile in the thickest films, but no diffusion is seen in thinner ones. Microscopic characterizations of the films are done with X-ray diffraction (XRD) measurements. All the samples are polycrystalline, with an hcp structure and show a 〈0 0 0 1〉 preferred orientation. Atomic force microscopies (AFM) reveal very smooth film surfaces.     

Phase and electrical behaviour in the Bi14W1 − xLaxO24 − 3x/2 system

The compositional and thermal dependencies of phase and electrical behaviour of compositions in the system Bi₁₄W_1 − xLa_xO_{24 − 3x/2} (0.00 < x < 1.00) have been studied by X-ray powder diffraction, differential thermal analysis and a.c. impedance spectroscopy. The system exhibits polymorphism and phase separation, which shows both compositional and thermal dependence. Compositions with x = 0.25 and x = 0.50 exhibit a single phase tetragonal structure at room temperature. In contrast, the x = 0.75 composition at room temperature shows a mixture of a cubic phase and a secondary β-Bi₂O₃ related tetragonal phase. A full solid solution is observed at high temperatures, corresponding to the occurrence of a δ-Bi₂O₃ type phase. The appearance of the various phases correlates well with the observed electrical behaviour. The x = 0.75 composition exhibits exceptionally high conductivity at high temperatures (σ₈₀₀ = 1.34 S cm^− 1), but also shows significant phase separation at lower temperatures.