Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

Dynamics of water adsorption on TiO2 monitored by work function spectroscopy

Water adsorption dynamics on two TiO₂ (1 1 0) rutile surfaces at room temperature has been investigated using the work function (WF) change as a function of time. The first surface was prepared in a standard way using sputtering/annealing cycles, whereas the second one was long term annealed at 620 K in moderate vacuum conditions (the residual gas pressure of about 1 × 10⁻⁷ mbar) and cleaned afterwards. The WF change show striking difference as compared to those obtained for highly reduced TiO₂ (1 1 0) rutile or the (2 × 1) reconstructed surfaces. For the first kind of surface we show that the observed adsorption dynamics can be qualitatively explained by the present understanding of the water adsorption on non-reconstructed TiO₂ (1 1 0) rutile surface according to which the bridging oxygen vacancies and Ti rows are the main adsorption sites. Although generally similar to the former results, water adsorption dynamics on the second kind of the surface has an additional feature that can be only explained by a new adsorption site, which we suggest to be due to (2 × 1) reconstructed regions coexisting with the non-reconstructed TiO₂ (1 1 0) surface.     

Adsorption of CO2 on PbO at ambient temperature

The adsorption of CO₂ on metal oxides at ambient temperature received less study largely due to the small adsorption amount. However, the adsorption is of interest in refreshing the atmosphere of isolated spaces. It was shown in the present work that P_bO was sensitive to low concentration CO₂ in the presence of water. An XPS examination indicated that P_bO changed to P_bCO₃ after the adsorption of CO₂; therefore, the adsorption is chemical in nature. In order to enlarge the CO₂ capacity, P_bO was dispersed on the surface of a silica gel with large surface area (710 m²/g). Both CO₂ capacity and adsorption rate indicated that the optimal dispersion manner of P_bO is the mono-molecular layer surface coverage. Breakthrough experiments showed that the prepared adsorbent could effectively capture low-concentration CO₂ at ambient temperature and pressure yielding a CO₂ capacity of 59.1 mg g⁻¹. The saturated adsorbent was regenerated on heating at 380 °C and the CO₂ capability was recovered.     

Investigation into the photo-induced change in wettability of hydrophobized TiO2 films

The photo-induced change in wettability of hydrophobized TiO₂ films has been investigated for steel coated with acidic TiO₂ nanosols containing varying concentrations of dispersed nanocrystalline titania, such as Degussa P25. The photo-induced change in wettability was evaluated by measuring the time-dependent drop of water contact angle (WCA) after samples had been soaked in either n-octyltriethoxysilane (OTS) or decanoic acid (DA). TiO₂ films treated in this way exhibit superhydrophobic behaviour, with WCA greater than 160°. After radiation with UV (black light), the superhydrophobic properties are transformed into superhydrophilic properties, with WCA of almost 0°. As P25 content and layer thickness increase, high rates of photo-induced change are found, but a moderate calcination regime is required. On the other hand, hardness and E modulus pass through a maximum at 25 wt% P25, so that a P25 content between 25 and 50 wt% is the optimum for practical uses. With such stable coatings, wettability can be controlled over a wide range, and the switch between hydrophobic and hydrophilic states can be carried out repeatedly when DA is used as the hydrophobizing agent. Use of a low calcination temperature (450 °C) for the intermediate annealing of the single layers in multilayer coatings and a short final sintering step at a relatively high temperature (e.g. 630 °C for 10 min) allow the preparation of relatively thin TiO₂ films on steel with a high photoactivity.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

Synthesis and bioactivity of highly ordered TiO2 nanotube arrays

The highly ordered TiO₂ nanotube arrays were fabricated by potentiostatic anodization of Ti foils in fluorinated dimethyl sulfoxide (DMSO). TiO₂ nanotube arrays are formed using a 40 V anodization potential for 24 h, with a length of 12 μm, diameter of 170 nm and aspect ration of about 70. The as-prepared nanotubes are amorphous, but can be crystallized as the heat treatment temperature increases. Anatase phase appears at a temperature of about 300 °C, then transforms to rutile phase at about 600 °C. After heat treatment at 500 °C and soaking in SBF for 14d, a thick apatite layer of about 13 μm covers the whole surface of TiO₂ nanotube arrays, indicating their excellent in vitro bioactivity, which is mainly attributed to their high specific surface area and the anatase phase.     

CO2 adsorption on branched polyethyleneimine-impregnated mesoporous silica SBA-15

Adsorption of pure CO₂ on SBA-15 impregnated with branched polyethyleneimine (PEI) has been studied. Materials were prepared by impregnating the pore surface of SBA-15 mesoporous silica with different amounts of branched PEI (10, 30, 50 and 70 wt%). Textural properties, elemental analysis and low angle XRD measurements of the prepared samples showed a progressive pore filling of SBA-15 as PEI loading was increased. Pure CO₂ adsorption isotherms on these modified SBA-15 materials were obtained at 45 °C, showing high adsorption efficiency for CO₂ removal at 1 bar. Chemisorption of CO₂ on amino sites of the modified SBA-15 seems to be the main adsorption mechanism. PEI content of impregnated SBA-15 influences the adsorption capacity of the material, being a relevant variable for CO₂ removal by adsorption. Temperature effect on adsorption was also studied in the range 25-75 °C, showing that temperature strongly influences CO₂ adsorption capacity. Adsorption capacity was also tested after regeneration of the PEI-impregnated SBA-15 materials. Our results show that these branched PEI-impregnated materials are very efficient even at low pressure and after several adsorption-regeneration cycles.     

Evolution with temperature of a single sol-gel TIO2 layer on sapphire (α-Al2O3) (0 0 0 1)

TiO₂ sol-gel layer has been deposited on single crystal sapphire (0 0 0 1) substrate. Evolution of the layer microstructure with the thermal treatment in the range 100-1100 °C has been studied using X-ray diffraction and X-ray reflectometry. TiO₂ layer density first increases with temperature up to 800 °C and then decreases with the appearance of a high roughness finally leading to anatase islands formation. The single crystal nature of the substrate seems to contribute to hinder the transformation of the anatase phase into the rutile phase and to induce a preferred orientation of the TiO₂ islands.     

Microstructures and magnetic properties of CoPt-TiO2 nanocomposite films prepared by annealing CoPt/TiO2 multilayers

CoPt-TiO₂ nanocomposite films were synthesized by rapid thermal annealing of CoPt/TiO₂ multilayers. The effects of annealing temperature, annealing time, Ag addition and TiO₂ volume fraction on the microstructures and magnetic properties of the CoPt-TiO₂ nanocomposite films were studied. Results showed that the ordering degree of CoPt and coercivity of CoPt-TiO₂ nanocomposites increased with annealing temperature. Increasing annealing time and Ag addition were able to increase the ordering degree and coercivity of CoPt. However, complete L1₀-ordering of CoPt at 550 °C annealing was not realized by increasing annealing time up to 30 min and Ag addition up to 30 vol.%. Increasing TiO₂ volume fraction at 700 °C annealing did not lead to the change of ordering of CoPt. However, the grain structure of the films changed slightly when TiO₂ volume fraction was larger than 56%. The coercivity of the film decreased slightly with the addition of TiO₂.     

EPR study of nitrogen-doped mesoporous TiO2 powders

Mesoporous titanium dioxide powders were synthesized by the sol-gel route either directly or using the P123 templating agent and nitrogen doping from thiourea. X-ray diffraction studies show that doping and structuring give rise to rutile growth at a relatively low temperature of 400 °C compared to the transition point of pure TiO₂, which is close to 900 °C. Systematic EPR experiments were performed in order to monitor the involved paramagnetic centres with respect to calcination treatments and also to probe the nitrogen doping efficiency in the host media. Several paramagnetic species were found in these mesostructured samples mainly with oxygen radicals for calcinations at 400 °C, while nitrogen centres appear for calcination temperature as high as 500 °C. The effect of material microstructure on the effective incorporation of nitrogen in the TiO₂ lattice is also examined and compared in representative samples.     

Theoretical study of CO adsorption on the illuminated TiO2 (0 0 1) surface

A quantum modeling of the CO adsorption on illuminated anatase TiO₂ (0 0 1) is presented. The calculated adsorption energy and geometries of illuminated case are compared with the ground state case. The calculations were achieved by using DFT formalism and the BH and HLYP. Upon photoexcitation, an electron-hole pair is generated. Comparing of natural population in the ground state and the exited state, shows that an electron is trapped in a Ti⁴⁺ ion and a hole is localized in an oxygen ion. The photoelectron helps generation of a CO₂ molecule on the TiO₂ surface. As shown by optimization of these systems, the CO molecule adsorbed vertically on the TiO₂ (0 0 1) surface in the ground state case while the CO molecule made an angle of 134.3° to this surface at the excited state case. Based on the here used model the obtained adsorption energy was 0.36 eV which is in excellent agreement with the reported experimental value. In the present work the C-O stretch IR frequencies are calculated which are 1366.53 and 1423.16 cm⁻¹. These results are in good agreement with the earlier reported works for the surface carbonaceous compounds, and oxygenated carbon species.     

Growth of ultra-thin TiO2 films by spray pyrolysis on different substrates

In the present study TiO₂ films were deposited by spray pyrolysis method onto ITO covered glass and Si (1 0 0) substrates. The spray solution containing titanium(IV) isopropoxide, acetylacetone and ethanol was sprayed at a substrate temperature of 450 °C employing 1-125 spray pulses (1 s spray and 30 s pause). According to AFM, continuous coverage of ITO and Si substrates with TiO₂ layer is formed by 5-10 and below 5 spray pulses, respectively. XPS studies revealed that TiO₂ film growth on Si substrate using up to 4 spray pulses follows 2D or layer-by-layer-growth. Above 4 spray pulses, 3D or island growth becomes dominant irrespective of the substrate. Only 50 spray pulses result in TiO₂ layer with the thickness more than XPS measurement escape depth as any signal from the substrate could not be detected. TiO₂ grain size remains 30 nm on ITO and increases from 10-20 nm to 50-100 nm on Si substrate with the number of spray pulses from 1 to 125.     

Investigation of chemical decomposition of CCl4 on TiO2 near room temperature

Dissociative adsorption of CCl₄ on TiO₂ at 35 °C has been studied by Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and electron spin resonance. CCl₄ decompose to form CO, CO₂, and CO₃ on the surface, at such a low temperature, in which CO₂ formation is not from CO oxidation on TiO₂, but CO₃ can be produced by CO and CO₂ adsorption. The Cl generated from CCl₄ decomposition is left on the surface and bonded to titanium ions. Mineralization of CCl₄ on TiO₂ involves the lattice oxygens. Thermodynamical driving force and possible reaction routes for CO and CO₂ formation in the CCl₄ decomposition on TiO₂ are discussed.     

Surface study of fine MgFe2O4 ferrite powder prepared by chemical methods

To study surface behaviors, MgFe₂O₄ ferrite materials having different grain sizes were synthesized by two different chemical methods, i.e., a polymerization method and a reverse coprecipitation method. The single phase of the cubic MgFe₂O₄ was confirmed by the X-ray diffraction method for both the precursors decomposed at 600-1000 °C except for a very small peak of Fe₂O₃ was detected for the samples calcined at 600 and 700 °C by the polymerization method. The crystal size and particle size increased with an increase in the sintering temperature using both methods. The conductance of the MgFe₂O₄ decreased when the atmosphere was changed from ambient air to air containing 10.0 ppm NO₂. The conductance change, C = G(air)/G(10 ppm NO₂), was reduced with an increase in the operating temperature. For the polymerization method, the maximum C-value was ca. 40 at 300 °C for the samples sintered at 900 °C. However, the samples sintered at 1000 °C showed a low conductance change in the 10 ppm NO₂ gas, because the ratio of the O₂ gas adsorption sites on the particle surface is smaller than those of the samples having a high C-value. The low Mg content on the surface affects the low ratio of the gas adsorption sites. For the reverse coprecipitation method, the particle size was smaller than that of the polymerization method. Although a stable conductance was obtained for the sample sintered at 900 and 1000 °C, its conductance change was less than that of the polymerization method.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

Effect of surface fluorination on the photocatalytic and photo-induced hydrophilic properties of porous TiO2 films

Porous surface-fluorinated TiO₂ (F-TiO₂) films were prepared through PEG modified sol-gel method and surface fluorination. The as-prepared films were characterized with XRD, FTIR, AFM, XPS and UV-vis DRS. The effects of surface fluorination on the photocatalytic activity and hydrophilicity of porous TiO₂ film were studied by photocatalytic degradation of rhodamine B (RhB) as well as water contact angle (CA) on porous TiO₂ film. The results showed that the surface fluorination increased the adsorption of RhB on the porous TiO₂ film and enhanced the photocatalytic degradation of RhB. The concentration and pH of NaF solutions affected much the photocatalytic activity of porous TiO₂ film. Porous F-TiO₂ film prepared in 40 mM NaF solution at pH 4.0 showed the highest photocatalytic activity. Because of its porous structure, the porous F-TiO₂ film had original water CA of 22.7°, which is much smaller than that of normal F-TiO₂ film. Under UV light irradiation, the water CA of porous F-TiO₂ film decreased to 5.1° in 90 min.     

Electrochemical properties of electrosynthesized TiO2 thin films

Titanium dioxide (TiO₂) thin films prepared by cathodic electrodeposition on indium-tin-oxide coated glass substrates from simple aqueous peroxo-titanium complex solutions have been studied as a function of sintering temperature (25-500 °C). The films crystallized in to anatase phase at relatively low temperature (300 °C). Electrochemical properties of amorphous and anatase films were investigated by cyclic voltammogram (CV) in lithium ion containing organic electrolyte. All the films were found to show reversible electrochemical properties upon Li⁺ ion intercalation. The effects of sintering temperature on the crystallinity and consequently on the electrochemical properties of TiO₂ has been discussed.     

Photocatalytic activity of multielement doped TiO2 in the degradation of congo red

TiO₂ although considered a promising photocatalyst for the degradation of aqueous pollutants, it suffers from poor absorption in the visible region and hence requires ultraviolet (UV) light for activation. To make TiO₂ a visible active photocatalyst, multielement (C, N, B, and F) doping has been done. The synthesised CNBF/TiO₂ catalysts were calcined at different temperatures and characterized by XRD, BET surface area, UV DRS, XPS, HRSEM-EDAX, and TEM techniques. These catalysts found to show less band gap values when compared to bare TiO₂. These catalysts were tested for their catalytic activity towards the degradation of a textile dye - congo red (CR) under different reaction conditions. It was found that the photocatalytic activity was dependent on both doping of multielement and the calcination temperature of CNBF/TiO₂. The co-doped catalysts which were calcined at 400 °C and 600 °C (100% intensity in anatase phase) were found to be the best catalysts (100% decolourisation of CR in 21/2 h and 2 h respectively). TOC analysis carried out for the samples at the reaction time of 5 h showed very high percentage (83%) degradation of CR over CNBF/TiO₂ catalysts calcined at 600 °C when compared to the other catalysts calcined at different temperatures. CNBF/TiO₂ (1000 °C) showed very less photocatalytic activity due to the formation of rutile phase.