Study of S ion-assisted sulfurization of n-GaAs (1 0 0) surface

The chemical structure and site location of sulfur atoms on n-GaAs (1 0 0) surface treated by bombardment of S⁺ ions over their energy range from 10 to 100 eV have been studied by X-ray photoelectron spectroscopy and low energy electron diffraction. The formation of Ga-S and As-S species on the S⁺ ion bombarded n-GaAs surface is observed. An apparent donor doping effect is observed for the n-GaAs by the 100 eV S⁺ ion bombardment. It is found that the S⁺ ions with higher energy are more effective in the formation of Ga-S species, which assists the n-GaAs (1 0 0) surface in reconstruction into an ordered (1 × 1) structure upon subsequent annealing. The treatment is further extended to repair Ar⁺ ion damaged n-GaAs (1 0 0) surface. It is found that after a n-GaAs (1 0 0) sample is damaged by 150 eV Ar⁺ ion bombardment, and followed by 50 eV S⁺ ion treatment and subsequent annealing process, finally an (1 × 1) ordering GaAs (1 0 0) surface with low surface states is obtained.     

Stability of hydrogen-terminated vicinal Si(1 1 1) surface under ambient atmosphere

In this paper a comparative study of different wet-chemical etching procedures of vicinal Si(1 1 1) surface passivation is presented. The stability against oxidation under ambient atmosphere was studied by X-ray photoelectron spectroscopy and atomic force microscopy. The best results were achieved by the buffered HF etching and the final smoothing of the surface by hot (72 °C) NH₄F. The procedures consisting of a large number of etching steps were unsatisfactory, since the probability of contamination during each step was increasing. The passivated surface was stable against oxidation for at least 3 h under ambient atmosphere.     

Structure and composition of chemically prepared and vacuum annealed InSb(0 0 1) surfaces

The InSb(0 0 1) surfaces chemically treated in HCl-isopropanol solution and annealed in vacuum were studied by means of X-ray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED) and electron energy-loss spectroscopy (EELS). The HCl-isopropanol treatment removes indium and antimony oxides and leaves on the surface about 3 ML of physisorbed overlayer, containing indium chlorides and small amounts of antimony, which can be thermally desorbed at 230 °C. The residual carbon contaminations were around 0.2-0.4 ML and consisted of the hydrocarbon molecules. These hydrocarbon contaminations were removed from the surface together with the indium chlorides and antimony overlayer. With increased annealing temperature, a sequence of reconstructions were identified by LEED: (1 × 1), (1 × 3), (4 × 3), and (4 × 1)/c(8 × 2), in the order of decreasing Sb/In ratio. The structural properties of chemically prepared InSb(0 0 1) surface were found to be similar to those obtained by decapping of Sb-capped epitaxial layers.     

Monolayer passivation of silicon(0 0 1) surface by selenium

Monolayer passivation of the silicon(0 0 1) surface by selenium is investigated in an ultrahigh vacuum environment with a solid selenium source by reflection high-energy electron diffraction and residual gas analysis. It is found that precisely one monolayer of selenium is deposited on silicon(0 0 1) when the silicon substrate temperature is set slightly above the selenium source temperature and the passivation time ensures a little overdose of selenium above one monolayer. The temperature settings prevent selenium condensation on silicon(0 0 1), which makes selenium deposition on silicon(0 0 1) a thermodynamically self-limited process to exactly one monolayer.     

An ab initio-based approach to adsorption-desorption behavior of Si adatoms on GaAs(1 1 1)A-(2 × 2) surfaces

The adsorption-desorption behavior of Si adatoms on GaAs(1 1 1)A-(2 × 2) surfaces is investigated using our ab initio-based approach, in which adsorption and desorption behavior of Si adatoms is described by comparing the calculated desorption energy obtained by total-energy electronic-structure calculations with the chemical potential estimated by quantum statistical mechanics. We find that the Si adsorption at the Ga-vacancy site on the (2 × 2) surfaces with As adatoms occurs less than 1140-1590 K while the adsorption without As adatom does less than 630-900 K. The change in adsorption temperature of Si adatoms by As adatoms is due to self-surfactant effects of As adatoms: the promotion of the Si adsorption triggered by As adatoms is found to be interpreted in terms of the band-energy stabilization. Furthermore, the stable temperature range for Si adsorbed surfaces with As adatoms agrees with the experimental results. The obtained results provide a firm theoretical framework to clarify n-type doping processes during GaAs epitaxial growth.     

Composition and morphology of fluorinated anodic oxides on InAs (1 1 1)A surface

The composition and morphology of fluorinated anodic oxide (FAO) films grown on InAs (1 1 1)A in alkaline aqueous (pH 11.5) and acid waterless (pH 1.5) electrolytes are studied by means of X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and high resolution transmission electron microscopy (HRTEM) in order to reveal the passivation mechanism of fluorine on the FAO/InAs(1 1 1)A interface. The formation of the highest oxidation form of As⁺⁵ and passivation of defects in the FAO layers during the fluorination process explain the reduction of the density of surface states and unpinning of the Fermi level on the fluorinated AO/InAs(1 1 1)A interface.     

XPS analysis of surface chemistry of near surface region of epiready GaAs(1 0 0) surface treated with (NH4)2Sx solution

In this work we analyze the effect of (NH)₂S_x wet treatment on the GaAs(1 0 0) covered with “epiready” oxide layer without any pretreatment in order to check the removal of oxides and carbon-related contamination, and the formation of sulfur species. The sulfidation procedure consisted of epiready sample dipping (at room and 40 °C temperatures) in an ammonium polysulfide solution combined with a UHV flash annealing up to 500 °C.The inspection of the XPS As 2p_3/2 and Ga 2p_3/2 spectra taken at surface sensitive mode revealed: (i) the temperature-dependent reduction of the amount of GaAs oxides and carbon contamination after sulfidation, and almost their complete removal after subsequent annealing, (ii) the creation of sulfur bonds with both Ga and As, with more thermally stable Ga-S bonds, and (iii) the slight reduction in elemental arsenic amount.     

Wet sulfur passivation of GaSb(1 0 0) surface for optoelectronic applications

A comparative analysis of the properties of the non-passivated and S-passivated GaSb(1 0 0) surfaces has been performed through PL, AFM and RHEED characterization. The samples treated with a 1 M Na₂S aqueous solution demonstrate an increase in the 5 K PL intensity. According to AFM data, the annealing of the S-passivated GaSb(1 0 0) leads to the formation of the clean flat (1 0 0) surface. Moreover, after annealing the PL intensity of the S-passivated GaSb(1 0 0) surfaces decreases by 20%, whereas for the non-passivated samples it drops by more than a factor of 4. The method of wet sulfur passivation has shown great effectiveness in pre-epitaxial processing for LPE and MBE growth of the GaSb-related materials for optoelectronics.     

Analysis of mechanism of carbon removal from GaAs(1 0 0) surface by atomic hydrogen

Etching of carbon contaminations from the GaAs(1 0 0) surface by irradiating with atomic hydrogen, which is one of the key reactions to promote high-quality thin films growth by molecular beam epitaxy (MBE), has been investigated by mass spectrometry (MS), Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). It is shown that during the cleaning process at room temperature a total reduction of the Auger carbon signal, accompanied by desorption of methane as major reaction product, can be observed. The reaction pathways as well as the processes responsible for the observed carbon removal are discussed in detail to give a support for etching and growth quality enhancement not only in thin films epitaxy but in all atomic hydrogen promoted gas-phase III-V semiconductor processes.     

Electronic and geometric structure of methyl oxirane adsorbed on Si(1 0 0)2 × 1

Electronic and geometric properties of the adsorbate-substrate complex formed upon adsorption of methyl oxirane on Si(1 0 0)2 × 1 at room temperature is reported, obtained with synchrotron radiation-induced valence and core-level photoemission. A ring-opening reaction is demonstrated to occur, followed by a five-membered ring formation involving two of the Si surface atoms bound to a surface dimer. Core-level photoemission spectra support the ring-opening reaction and the SiO and SiC bond formation, while from the valence spectra a more extended molecular fragmentation can be ruled out. We discuss the most likely geometry of the five-membered ring.     

The periodicity in translation of Ag (0 0 1) and (1 1 0) twist grain boundary

The energies of Ag (0 0 1) and (1 1 0) twist grain boundary (GB) in translation have been calculated with the modified analytical embedded atom method (MAEAM). The energy period corresponds exactly to the DSC lattice unit cell and the area of the energy period referred to the CSL unit cell is 1/Σ². The ‘energy grooves’ are parallel to the sides of the CSL or DSC lattice unit cell. The most preferable sliding direction is parallel to identical sides of the square CSL unit cell for (0 0 1) boundaries and to the short side of the rectangular CSL unit cell for (1 1 0) boundaries. From energy minimization, the stable configuration appears when two adjacent grains are translated relatively to the corners, centre or sides’ midpoint of the DSC lattice unit cell.     

Combined EELS, LEED and SR-XPS study of ultra-thin crystalline layers of indium nitride on InP(1 0 0)—Effect of annealing at 450 °C

In this study, InP(1 0 0) surfaces were bombarded by argon ions in ultra high vacuum. Indium metallic droplets were created in well controlled quantities and played the role of precursors for the nitridation process. A glow discharge cell was used to produce a continuous plasma with a majority of N atomic species. X-ray photoelectron spectroscopy (XPS) studies indicated that the nitrogen combined with indium surface atoms to create InN thin films (two monolayers) on an In rich-InP(1 0 0) surface. This process occurred at low temperature: 250 °C. Synchrotron radiation photoemission (SR-XPS) studies of the valence band spectra, LEED and EELS measurements show an evolution of surface species and the effect of a 450 °C annealing of the InN/InP structures. The results reveal that annealing allows the crystallization of the thin InN layers, while the LEED pattern shows a (4 × 1) reconstruction. As a consequence, InN related structures in EELS and valence bands spectra are different before and after the annealing. According to SR-XPS measurements, the Fermi level is found to be pinned at 1.6 eV above the valence band maximum (VBM).     

Oxidation of a cesium-covered Ni (1 1 0) surface studied by metastable-induced electron spectroscopy

An initial stage of oxidation of a cesium-covered Ni (1 1 0) surface has been studied by metastable-induced electron spectroscopy (MIES) and low-energy electron diffraction (LEED). The MIES brought spectra with Cs 6s induced peak (P_6s), Cs 5p (P_5p), O 2p induced peak (P_ox) and a structure related to the substrate Ni 3d states (P_3d). The work function change Δφ showed an oscillatory behavior in the progress of surface oxidation. The process is divided into three stages: (i) at low O₂ exposures, Δφ > 0 with unchanging P_5p and P_6s; (ii) at moderate exposures, Δφ < 0 with a drastic decrease in the P_6s intensity; (iii) at higher exposures, Δφ > 0 with shifts of peaks P_5p and P_ox to higher energies, together with an appearance of peak P_3d. A three-step model of initial oxidation of alkali-covered Ni (1 1 0) surfaces is presented.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

Nano- and micro-scale patterning of Si (1 0 0) under keV ion irradiation

Evolution of Si (1 0 0) surface under 100 keV Ar⁺ ion irradiation at oblique incidence has been studied. The dynamics of surface erosion by ion beam is investigated using detailed analysis of atomic force microscopy (AFM) measurements. During an early stage of sputtering, formation of almost uniformly distributed nano-dots occurs on Si surface. However, the late stage morphology is characterized by self-organization of surface into a regular ripple pattern. Existing theories of ripple formation have been invoked to provide an insight into surface rippling.     

Oxidation mechanism of hydrogen-terminated Ge(1 0 0) surface

Control of the surface chemistry to prepare a robust termination on the Ge surface is crucial for the development of high-end Ge devices. In this study, oxidation of a H-terminated Ge surface was studied in air ambient and H₂O using a multiple internal reflection Fourier transform infrared spectroscopy (MIR FT-IR) technique. Ge surface treated in less diluted HF exhibited a stronger Ge-H peak intensity, and the surface was easily oxidized in the air ambient. Therefore, it is believed that the treatment of the Ge surface in highly diluted HF solution has an advantage in suppressing the oxidation of Ge in the air ambient. For the oxidation of Ge(1 0 0) surface in air ambient, the Ge surface is attacked by oxidizing agents to break Ge-H and Ge-Ge bonds, and the transition GeO_x layer is first formed, followed by a layer-by-layer GeO₂ formation with the increase in exposure time. When the H-terminated Ge surface was treated in H₂O, GeO_x was mainly formed, the thickness of the oxide layer was not changed with an increase in treatment time, and the Ge surface was maintained in a suboxide state, which exhibits a different oxidation mechanism from that in air ambient.     

Electronic surface states on the MOVPE-prepared InGa-terminated InGaAs(1 0 0) (4 × 2)/c(8 × 2) surface

In this paper, the InGa-terminated InGaAs(1 0 0) (4 × 2)/c(8 × 2) surface was studied in detail, which turned out to be the most suitable to develop an InGaAs/GaAsSb interface that is as sharp as possible. In ultra high vacuum the InGaAs surface was investigated with low-energy electron diffraction, scanning tunneling microscopy and UV photoelectron spectroscopy employing synchrotron radiation as light source. Scanning the Γ−Δ−X direction by varying the photon energy between 8.5 eV and 50 eV, two surface states in the photoelectron spectra were observed in addition to the valence band peaks.     

Hydrogen-induced metallization on Ge(1 1 1) c(2 × 8)

We have studied hydrogen adsorption on the Ge(1 1 1) c(2 × 8) surface using scanning tunneling microscopy (STM) and angle-resolved photoelectron spectroscopy (ARPES). We find that atomic hydrogen preferentially adsorbs on rest atom sites. The neighbouring adatoms appear higher in STM images, which clearly indicates a charge transfer from the rest atom states to the adatom states. The surface states near the Fermi-level have been followed by ARPES as function of H exposure. Initially, there is strong emission from the rest atom states but no emission at the Fermi-level which confirms the semiconducting character of the c(2 × 8) surface. With increasing H exposure a structure develops in the close vicinity of the Fermi-level. The energy position clearly indicates a metallic character of the H-adsorbed surface. Since the only change in the STM images is the increased brightness of the adatoms neighbouring a H-terminated rest atom, we identify the emission at the Fermi-level with these adatom states.     

Stability of MgO(1 1 1) films grown on 6H-SiC(0 0 0 1) by molecular beam epitaxy for two-step integration of functional oxides

Crystalline magnesium oxide (MgO) (1 1 1), 20 Å thick, was grown by molecular beam epitaxy (MBE) on hydrogen cleaned hexagonal silicon carbide (6H-SiC). The films were further heated to 740 °C and 650 °C under different oxygen environments in order to simulate processing conditions for subsequent functional oxide growth. The purpose of this study was to determine the effectiveness and stability of crystalline MgO films and the MgO/6H-SiC interface for subsequent heteroepitaxial deposition of multi-component, functional oxides by MBE or pulsed laser deposition processes. The stability of the MgO films and the MgO/6H-SiC interface was found to be dependent on substrate temperature and the presence of atomic oxygen. The MgO films and the MgO/6H-SiC interface are stable at temperatures up to 740 °C at 1.0 × 10⁻⁹ Torr for extended periods of time. While at temperatures below 400 °C exposure to the presence of active oxygen for extended periods of time has negligible impact, exposure to the presence of active oxygen for more than 5 min at 650 °C will degrade the MgO/6H-SiC interface. Concurrent etching and interface breakdown mechanisms are hypothesized to explain the observed effects. Further, barium titanate was deposited by MBE on bare 6H-SiC(0 0 0 1) and MgO(1 1 1)/6H-SiC(0 0 0 1) in order to evaluate the effectiveness of the MgO as a heteroepitaxial template layer for perovskite ferroelectrics.     

Structure and electronic properties of gold adsorbed on Ti(0 0 0 1)

The Au/Ti(0 0 0 1) adsorption system was studied by low energy electron diffraction (LEED) and photoemission spectroscopy with synchrotron radiation after step-wise Au evaporation onto the Ti(0 0 0 1) surface. For adsorption of Au at 300 K, no additional superstructures were observed and the (1 × 1) pattern of the clean surface simply became diffuse. Annealing of gold layers more than 1 ML thick resulted in the formation of an ordered Au-Ti surface alloy. Depending on the temperature and annealing time, three surface reconstructions were observed by LEED: (√3 × √3) R30°, (2 × 2) and a one-dimensional incommensurate (√3 × √3) rectangular pattern. The Au 4f core level and valence band photoemission spectra provided evidence of a strong chemical interaction between gold and titanium. The data indicated formation of an intermetallic interface and associated valence orbital hybridization, together with diffusion of gold into the bulk. Au core-level shifts were found to be dependent on the surface alloy stoichiometry.