Electrical characterisation of phosphorus-doped ZnO thin films grown by pulsed laser deposition

Phosphorus-doped ZnO films were grown by pulsed laser deposition using a ZnO:P₂O₅-doped target as the phosphorus source with the aim of producing p-type ZnO material. ZnO:P layers (with phosphorus concentrations of between 0.01 to 1 wt%) were grown on a pure ZnO buffer layer. The electrical properties of the films were characterised from temperature dependent Hall-effect measurements. The samples typically showed weak n-type conduction in the dark, with a resistivity of 70 Ω cm, a Hall mobility of μ_n0.5 cm² V ⁻¹ s⁻¹ and a carrier concentration of n3×10¹⁷ cm⁻³ at room temperature. After exposure to an incandescent light source, the samples underwent a change in conduction from n- to p-type, with an increase in mobility and decrease in concentration for temperatures below 300 K.     

Structural and optical properties of ZnO thin films deposited on quartz glass by pulsed laser deposition

ZnO thin films with typical c-axis (0 0 2) orientation were successfully deposited on quartz glass substrates by pulse laser ablation of Zn target in oxygen atmosphere at a relatively low temperature range of 100-250 °C. The structural and optical properties of the films were studied. In photoluminescence (PL) spectra at room temperature, single ultraviolet emission (without deep-level emission) was obtained from ZnO film deposited at the temperature of 200 °C. This was attributed to its low intrinsic defects.     

Fabrication of p-type Li-doped ZnO films by pulsed laser deposition

p-Type ZnO thin films have been realized via doping Li as acceptor by using pulsed laser deposition. In our experiment, Li₂CO₃ was used as Li precursor, and the growth temperature was varied from 400 to 600 °C in pure O₂ ambient. The Li-doped ZnO film prepared at 450 °C possessed the lowest resistivity of 34 Ω cm with a Hall mobility of 0.134 cm² V⁻¹ s⁻¹ and hole concentration of 1.37 × 10¹⁸ cm⁻³. X-ray diffraction (XRD) measurements showed that the Li-doped ZnO films grown at different substrate temperatures were of completely (0 0 2)-preferred orientation.     

Room temperature growth and properties of ZnO films by pulsed laser deposition

ZnO thin films were prepared by pulsed laser deposition at room temperature on glass substrates with oxygen pressures of 10-30 Pa. The structural, electrical, and optical properties of ZnO films were studied in detail. ZnO films had an acceptable crystal quality with high c-axis orientation and smooth surface. The resistivity was in the 10² Ω cm order for ZnO films, with the electron concentration of 10¹⁶-10¹⁷ cm⁻³. All the films showed a high visible transmittance ∼90% and a high UV absorption about 90-100%. The UV emission ∼390 nm was observed in the photoluminescence spectra. The oxygen pressures in the 10-30 Pa range were suitable for room temperature growth of high-quality ZnO films.     

Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.     

Optical and electrical properties of aluminum-doped ZnO thin films grown by pulsed laser deposition

Transparent aluminum-doped zinc oxide (AZO) thin films were deposited on quartz glass substrates by pulsed laser deposition (PLD) from ablating Zn-Al metallic targets. The structural, electrical and optical properties of these films were characterized as a function of Al concentration (0-8 wt.%) in the target. Films were deposited at a low substrate temperature of 150 °C under 11 Pa of oxygen pressure. It was observed that 2 wt.% of Al in the target (or 1.37 wt.% of Al doped in the AZO film) is the optimum concentration to achieve the minimum film resistivity and strong ultraviolet emission. The presence of Al in the ZnO film changes the carrier concentration and the intrinsic defects.     

Role of vanadium content in ZnO thin films grown by pulsed laser deposition

Vanadium-doped ZnO films (Zn_1−xV_xO, where x = 0.02, 0.03, 0.05 and 0.07), were formed from ceramic targets on c-cut sapphire substrates using pulsed laser deposition at substrate temperature of 600 °C and oxygen pressure of 10 Pa. In order to clarify how the vanadium concentration influences the films’ properties, structural and magnetic investigations were performed. All films crystallised in wurtzite phase and presented a c-axis preferred orientation at low concentrations of vanadium. The results implied that the doping concentration and crystalline microstructure influence strongly the system's magnetic characteristics. Weak ferromagnetism was registered for the film with the lowest doping concentration (2 at.%), which exhibited a ferromagnetic behavior at Curie temperature higher than 300 K. Increasing the vanadium content in the film caused degradation of the magnetic ordering.     

Properties of Dy-doped ZnO nanocrystalline thin films prepared by pulsed laser deposition

Highly transparent conductive Dy₂O₃ doped zinc oxide (ZnO)_1-x(Dy₂O₃)_x nanocrystalline thin films with x from 0.5% to 5% have been deposited on glass substrate by pulsed laser deposition technique. The structural, electrical and optical properties of Dy₂O₃ doped thin films were investigated as a function of the x value. The experimental results show that the Dy concentration in Dy-doped ZnO thin films has a strong influence on the material properties especially electrical properties. The resistivity decreased to a minimum value of 5.02 × 10⁻⁴ Ω cm with x increasing from 0.5% to 1.0%, then significantly increased with the further increasing of x value. On the contrary, the optical direct band gap of the (ZnO)_1-x(Dy₂O₃)_x films first increased, then decreased with x increasing. The average transmission of Dy₂O₃ doped zinc oxide films in the visible range is above 90%.     

Effect of different annealing temperature on Sb-doped ZnO thin films prepared by pulsed laser deposition on sapphire substrates

Influence of annealing temperature on the properties of Sb-doped ZnO thin films were studied. Hall measurement results indicated that the Sb-doped ZnO annealed at 950 °C was p-type conductivity. X-ray diffraction (XRD) results indicated that the Sb-doped ZnO thin films prepared at the experiments are high c-axis oriented. It was worth noting that p-type sample had the worst crystallinity. The measurements of low-temperature photoluminescence (PL) spectra indicate that the sample annealed at the temperatures of 950 °C showed strong acceptor-bound exciton (A⁰X) emission, and confirmed that it is related to Sb-doping by comparing with the undoped ZnO low-temperature PL spectrum.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Characterization of nitrogen-doped ZnO thin films grown by plasma-assisted pulsed laser deposition on sapphire substrates

The crystalline, optical and electrical properties of N-doped ZnO thin films were measured using X-ray diffraction, photoluminescence and Hall effect apparatus, respectively. The samples were grown using pulsed laser deposition on sapphire substrates coated priorly with ZnO buffer layers. For the purpose of acceptor doping, an electron cyclotron resonance (ECR) plasma source operated as a low-energy ion source was used for nitrogen incorporation in the samples. The X-ray diffraction analyses indicated some deterioration of the ZnO thin film with nitrogen incorporation. Temperature-dependent Van der Pauw measurements showed consistent p-type behavior over the measured temperature range of 200–450 K, with typical room temperature hole concentrations and mobilities of 5×10¹⁵ cm⁻³ and 7 cm²/V s, respectively. Low temperature photoluminescence spectra consisted of a broad emission band centered around 3.2 eV. This emission is characterized by the absence of the green deep-defect band and the presence of a band around 3.32 eV.     

Nanocomposite ZnO/Au formation by pulsed laser irradiation

The ZnO/Au nanocomposite formation involves synthesis of Au and ZnO colloidal solutions by 532 nm pulse laser ablation of metal targets in deionized water followed by laser irradiation of the mixed colloidal solution. The transmission electron microscope (TEM) and high-resolution transmission electron microscope (HRTEM) images show evolution of spherical particles into ZnO/Au nanonetworks with irradiation time. The formation mechanism of the nanonetwork can be explained on the basis of near resonance absorption of 532 nm irradiation by gold nanoparticles which can cause selective melting and fusion of gold nanoparticles to form network. The ZnO/Au nanocomposites show blue shift in the ZnO exciton absorption and red shift in the Au plasmon resonance absorption due to interfacial charge transfer.     

Bioactive glass and hydroxyapatite thin films obtained by pulsed laser deposition

Bioactive glass (BG), calcium hydroxyapatite (HA), and ZrO₂ doped HA thin films were grown by pulsed laser deposition on Ti substrates. An UV KrF^* (λ = 248 nm, τ ≥ 7 ns) excimer laser was used for the multi-pulse irradiation of the targets. The substrates were kept at room temperature or heated during the film deposition at values within the (400-550 °C) range. The depositions were performed in oxygen and water vapor atmospheres, at pressure values in the range (5-40 Pa). The HA coatings were heat post-treated for 6 h in a flux of hot water vapors at the same temperature as applied during deposition. The surface morphology, chemical composition, and crystalline quality of the obtained thin films were studied by scanning electron microscopy, atomic force microscopy, and X-ray diffractometry. The films were seeded for in vitro tests with Hek293 (human embryonic kidney) cells that revealed a good adherence on the deposited layers. Biocompatibility tests showed that cell growth was better on HA than on BG thin films.     

Growth and characterization of pulsed laser deposited ZnO thin films

One of the most important and promising materials from metal oxides is ZnO with specific properties for near UV emission and absorption optical devices. The properties of ZnO thin films strongly depend on the deposition method. Among them, pulsed laser deposition (PLD) plays an important role for preparing various kinds of ZnO films, e.g. doped, undoped, monocrystalline, and polycrystalline. Different approaches — ablation of sintered ZnO pellets or pure metallic Zn as target material are described. This contribution is comparing properties of ZnO thin films deposited from pure Zn target in oxygen atmosphere and those deposited from sintered ZnO target. There is a close connection between final thin film properties and PLD conditions. The surface properties of differently grown ZnO thin films are measured by secondary ion mass spectrometry (SIMS), atomic force microscopy (AFM) and scanning electron microscopy (SEM). Furthermore, different approaches — ablation of sintered ZnO pellet or pure metallic Zn as target materials are described. The main results characterize typical properties of ZnO films versus technological parameters are presented. Presented at 5-th International Conference Solid State Surfaces and Interfaces, November 19–24, 2006, Smolenice Castle, Slovakia     

Structural investigations of ITO-ZnO films grown by the combinatorial pulsed laser deposition technique

Mixtures of transparent and conductive oxides such as ITO-ZnO have been grown by a combinatorial pulsed laser deposition technique from two targets that were located 15 mm apart. The films were deposited on (1 0 0)Si and quartz substrates that were heated at temperatures from 300 to 500 °C. Measurements of the In to Zn ratios along the transversal axis of the substrates, which passes through the maximum thickness points corresponding to each target position were performed using energy dispersive X-ray spectroscopy and spectroscopic ellipsometry. From simulations of the X-ray reflectivity spectra, collected with a 2 mm mask on different locations along the transversal axis of the samples, the density and thickness of the deposited films were calculated and then the In to Zn ratios. The crystalline structure and electrical properties of the deposited films were also investigated along the same axis. Changes in the ratio of In/Zn along this axis resulted in changes of the film lattice constant and texture.     

ZnO薄膜的激光辐照效应研究

研究了KrF准分子激光辐照对ZnO薄膜的本征缺陷.紫外（UV）发光以及表面形貌的影响,并对室温下ZnO的UV发射机理进行了详细探讨.结果表明激光辐照打断了薄膜内Zn—O键,氧空位（锌填隙）增多,导致表面电阻率下降,载流子浓度升高,调节激光辐照能量密度,可在较大范围内调控ZnO薄膜中的施主缺陷浓度;同时在激光热效应作用下,薄膜晶粒熔融长大,表面粗糙度大大降低;室温下ZnO薄膜的UV发光包括自由激子复合发光（FX）及其声子伴线（FX-LO）,缺陷浓度决定了FX与FX-LO的相对强度比,进而影响UV发射峰的强度以及位置.因此,激光辐照可以快速、有效地对ZnO薄膜内的缺陷浓度进行调控,从而控制其室温下的UV发射强度,这对于提高ZnO基光电器件的性能具有重要意义. 关键词： ZnO薄膜 激光辐照 紫外发光 缺陷浓度     

Non-stoichiometry-induced metal-to-insulator transition in nickelate thin films grown by pulsed laser deposition

While controlling the cation contents in perovskite rare-earth nickelate thin films, a metal-to-insulator phase transition is reported. Systematic control of cation stoichiometry has been achieved by manipulating the irradiation of excimer laser in pulsed laser deposition. Two rare-earth nickelate bilayer thin-film heterostructures with the controlled cation stoichiometry (i.e. stoichiometric and Ni-excessive) have been fabricated. It is found that the Ni-excessive nickelate film is structurally less dense than the stoichiometric film, albeit both of them are epitaxial and coherent with respect to the underlying substrate. More interestingly, as a temperature decreases, a metal-to-insulator transition is only observed in the Ni-excessive nickelate films, which can be associated with the enhanced disproportionation of the Ni charge valence. Based on our theoretical results, possible origins (e.g. anti-site defects) of the low-temperature insulating state are discussed with the need of future work for deeper understanding. Our work can be utilized to realize unusual physical phenomena (e.g. metal-to-insulator phase transitions) in complex oxide films by manipulating the chemical stoichiometry in pulsed laser deposition.     

Oxygen incorporation in ZnTe thin films grown by plasma-assisted pulsed laser deposition

We studied oxygen incorporation into ZnTe thin films with nitrogen and oxygen plasma during a plasma-assisted pulsed laser deposition (PA-PLD). It was shown that ZnTe:O layer formed with oxygen plasma exhibits an enhancement of optical transparency in visible spectral region due to the formation of amorphous TeO_x. Especially, the ZnTe:NO deposited by PA-PLD under nitrogen and oxygen partial pressures with N₂:O₂ of 10:3 sccm showed p-type semiconducting characteristics and the formation of intermediate band at about 0.5–0.8 eV below the ZnTe band edge. These results for oxygen incorporation in ZnTe thin film such as the enhancement of optical transparency in visible spectral region and the intermediate band formation will be useful for optoelectronic devices or intermediate band solar cells.     

Crystallization and grain growth characteristics of yttria-stabilized zirconia thin films grown by pulsed laser deposition

Knowledge about the crystallization and grain growth characteristics of metal oxide thin films is essential for effective microstructural engineering by thermal post-annealing and the integration to Si-based miniaturized electroceramic devices. Finite size and interface effects may cause fundamentally different behavior compared to three dimensional macroscopic systems. This work presents a comprehensive investigation of the crystallization kinetics and microstructural evolution upon thermal post-annealing of amorphous 200 nm and 1.2 μm thin films of 8 mol% yttria-stabilized zirconia grown by pulsed laser deposition (PLD) using ex- and in-situ X-ray diffraction, Raman spectroscopy, and electron microscopy techniques. The layers exhibit a remarkably low crystallization temperature of 200-250 °C while exposure to energetic electrons induces the formation of randomly dispersed ~ 20 nm sized crystallites already at ambient temperature. The isothermal amorphous to crystalline phase transformation kinetics can be described quantitatively by the Johnson-Mehl-Avrami-Kolmogorov model. They reveal characteristics of a three dimensional growth under cation bulk diffusion control with heterogeneous nucleation that changes from continuous to instantaneous initial seeding at temperatures above 300 °C. Large (> 100 nm) equiaxed grains are formed rapidly without a stabilization of transient nanocrystals during the thermally induced phase transformation. A stagnation of normal grain growth resulting in a logarithmic normal size distribution is observed once the average grain dimensions approach the film thickness. The results on the crystallization and grain growth of the PLD-grown YSZ films are evaluated with regards to the fabrication of YSZ solid electrolyte membranes for Si-supported micro solid oxide fuel cells and gas sensors.     

Influence of substrate temperature and post-treatment on the properties of ZnO:Al thin films prepared by pulsed laser deposition

Highly transparent conductive Al₂O₃ doped zinc oxide (AZO) thin films have been deposited on the glass substrate by pulsed laser deposition technique. The effects of substrate temperature and post-deposition annealing treatment on structural, electrical and optical properties of AZO thin films were investigated. The experimental results show that the electrical resistivity of films deposited at 240 °C is 6.1 × 10⁻⁴ Ω cm, which can be further reduced to as low as 4.7 × 10⁻⁴ Ω cm by post-deposition annealing at 400 °C for 2 h in argon. The average transmission of AZO films in the visible range is 90%. The optical direct band gap of films was dependent on the substrate temperature and the annealing treatment in argon. The optical direct band gap value of AZO films increased with increasing annealing temperature.