Substrate and orientation influence on electrical properties of sputtered La-doped PZT thin films

Pb_1−2y/3La_yZr_xTi_1−xO₃ (PLZT) thin films have been prepared “in situ” by multi-target sputtering on Silicon, LaAlO₃ (LAO) and MgO substrates covered with a Pt bottom electrode. The purpose was to grow tetragonal PLZT films (Zr/Ti = 28/72 with different La contents) on these various substrates and to compare their electrical properties. To this aim, Pt was first deposited on the three different substrates to get (1 1 1)Pt/Si, (1 1 1)Pt/LAO and (2 0 0)Pt/MgO. Then PLZT was deposited in a same run on these three kinds of substrates and the influence of La contents and film orientation on electrical properties was investigated. The La content was varied from y = 0 to y = 32 in order to explore the phase transition between ferroelectric and paraelectric phases as a function of the substrate. For large amount of Lanthanum, relaxor behavior has been observed and studied.     

Surfactant effect of Sb on the growth of MnSi1.7 layers on Si(0 0 1)

Deposition of one monolayer of Sb prior to the deposition of Mn at 600 °C is observed to increase the MnSi_1.7 island density by about two orders of magnitude as well as to change the crystalline orientation of the silicide grains. The preferential epitaxial orientation of MnSi_1.7 grains grown by this process is determined to be MnSi_1.7(1 0 0)[0 1 0]||Si(0 0 1)[1 0 0]. This growth procedure results in the silicide growth into the Si matrix. For comparison, the same deposition process carried out without Sb leads to silicide formation on top of the substrate surface. The observed morphological changes of the MnSi_1.7 layers can be explained by a reduced surface diffusion of the Mn atoms on Si(0 0 1) in presence of the Sb monolayer. Additionally, lateral Si diffusion is considered to be nearly suppressed, which is responsible for the observed silicide growth into the substrate.     

ZnO thin films on Si(1 1 1) grown by pulsed laser deposition from metallic Zn target

ZnO thin films with highly c-axis orientation have been fabricated on p-type Si(1 1 1) substrates at 400 °C by pulsed laser deposition (PLD) from a metallic Zn target with oxygen pressures between 0.1 and 0.7 mbar. Experimental results indicate that the films deposited at 0.3 and 0.5 mbar have better crystalline and optical quality and flatter surfaces than the films prepared at other pressures. The full width at half maximum (FWHM) of (0 0 0 2) diffraction peak decreases remarkably from 0.46 to 0.19° with increasing annealing temperature for the film prepared at 0.3 mbar. In photoluminescence (PL) spectra at room temperature, the annealed film at 700 °C exhibits a smaller ultraviolet (UV) peak FWHM of 108 meV than the as-grown film (119 meV). However, an enhanced deep-level emission is observed. Possible origins to above results are discussed.     

Growth of Ag thin films on ZnO(0 0 0 −1) investigated by AES and STM

The growth of Ag films on ZnO(0 0 0 −1) has been investigated by Auger electron spectroscopy (AES) and scanning tunneling microscopy (STM). A high density of islands is nucleated at the earliest stages of the growth. An upstepping mechanism causes these islands to coalesce while the uncovered fraction of the ZnO surface remains constant (30%).     

Effect of a LaSrCoO3 buffer layer on Pb1 − xLaxTi1 − x/4O3 films studied by polarized Raman spectroscopy

A confocal Raman investigation of Pb_1 − xLa_xTi_1 − x/4O₃ (PLT) thin films grown by RF magnetron sputtering on PbO_x/Pt/Ti/SiO₂/Si substrates with an intermediate LaSrCoO₃ (LSCO) layer was performed. The influence of the LaSrCoO₃ buffer layer was analyzed taking advantage of the observed Raman spectral band variation, which varied according to different manufacturing procedures. In the presence of a LSCO layer, the A1(1TO) Raman mode, which was indicative of tetragonal distortion, was pronouncedly enhanced, and a slight deviation from the (0 0 1) plane of the film was observed from the angular dependence of the polarized Raman spectral intensity. Furthermore, the spectral band variation as well as the residual stress along the in-depth direction was measured in the film from cross-sectional spectral line scans. This latter measurement showed a relaxation of the lattice mismatch in the presence of LSCO and PbO layers.     

Structure, dielectric and ferroelectric properties of highly (1 0 0)-oriented BaTiO3 grown under low-temperature conditions

The highly (1 0 0)-oriented BaTiO₃ thin films were fabricated on LaNiO₃(1 0 0)/Pt/Ti/SiO₂/Si substrates under low-temperature conditions. Substrate temperatures throughout the fabrication process remained at or below 400 °C, which allows this process to be compatible with many materials commonly used in integrated circuit manufacturing. X-ray diffraction data provided the evidence for single BaTiO₃ phase. Field-emission scanning electron microscopy was used to study the columnar structure of the films. The dielectric properties as a function of frequency in the range of 1 kHz to 1 MHz was obtained. The room temperature remanent polarization (2P_r) and coercive field were found to be ∼5 μC/cm² and 50 kV/cm, respectively. The BTO film maintains an excellent fatigue-free character even after 10⁹ switching cycles.     

Thickness dependence on thermal stability of sputtered Ag nanolayer on Ti/Si(1 0 0)

Thermal stability of Ag layer on Ti coated Si substrate for different thicknesses of the Ag layer have been studied. To do this, after sputter-deposition of a 10 nm Ti buffer layer on the Si(1 0 0) substrate, an Ag layer with different thicknesses (150-5 nm) was sputtered on the buffer layer. Post annealing process of the samples was performed in an N₂ ambient at a flow rate of 200 ml/min in a temperature range from 500 to 700 °C for 30 min. The electrical property of the heat-treated multilayer with the different thicknesses of Ag layer was examined by four-point-probe sheet resistance measurement at the room temperature. Phase formation and crystallographic orientation of the silver layers were studied by θ-2θ X-ray diffraction analysis. The surface topography and morphology of the heat-treated films were determined by atomic force microscopy, and also, scanning electron microscopy. Four-point- probe electrical measurement showed no considerable variation of sheet resistance by reducing the thickness of the annealed Ag films down to 25 nm. Surface roughness of the Ag films with (1 1 1) preferred crystallographic orientation was much smaller than the film thickness, which is a necessary condition for nanometric contact layers. Therefore, we have shown that the Ag layers with suitable nano-thicknesses sputtered on 10 nm Ti buffer layer were thermally stable up to 700 °C.     

Epitaxial growth of Nd2Hf2O7(1 1 1) thin films on Ge(1 1 1) substrates by pulsed laser deposition

Nd₂Hf₂O₇ (NHO) thin films have been epitaxially grown by pulsed laser deposition (PLD) on Ge(1 1 1) substrates. In situ reflection high-energy electron diffraction (RHEED) evolution of the (1 1 1)-oriented NHO during the deposition has been investigated and shows that the epilayer has a twin-free character with type-B stacking. Interfacial structure of NHO/Ge has been examined by high-resolution transmission electron microscopy (HRTEM). The results indicate a highly crystalline film with a very thin interface, and the orientation relationship between NHO and Ge can be denoted as (1 1 1)_NHO//(1 1 1)_Ge and . Finally, twin-free epitaxial growth of NHO with type-B orientation displays temperature dependence and the type-B epitaxy is favored at high temperature.     

Highly oriented (1 0 0) ZnO thin films by spray pyrolysis

Undoped ZnO thin films have been deposited onto glass substrates by spray pyrolysis. The structural, electrical and optical properties were studied on thin films, prepared from precursor solutions with varying the ethanol concentrations. X-ray diffraction studies have shown polycrystalline nature of the films with a hexagonal wurtzite-type structure. The preferential orientation plane (1 0 0) of the ZnO thin film is found to be sensitive to ethanol concentration. The texture coefficient (TC) and grain size value have been calculated. Also ethanol concentration was found to have significant effect on sheet resistivity of the films.     

Morphology of pentacene films deposited on Cu(1 1 9) vicinal surface

We investigate the morphology of a pentacene (C₂₂H₁₄) film adsorbed on the Cu(1 1 9) vicinal surface by scanning tunnelling microscopy (STM). Thermal treatment of a thick film of molecules generates a long-range ordered structure. Series of molecular rows are alternated with areas where the molecules assume two equivalent orientations. STM data analysis suggests that the ordered structure can be described by a rippled morphology. The behaviour of the film at different annealing temperatures suggests a possible explanation of the film structure as due to an adsorbate-induced modification of the substrate.     

Influence of substrate temperature on the chemical and microstructural properties of MO-CVD ZrTiO<Subscript>4</Subscript> thin films

In the last few years, intensive research activity has been focused on the development of suitable synthesis methods for high-permittivity materials, used for the realization of next-generation microdevices able to fulfil the previsions of the Technology Roadmap of Semiconductors. The use of high-permittivity materials can overcome the difficulties concerning the production of SiO₂-based ultra-thin dielectrics, such as the generation of pinholes and the non-uniformity of the film, which may result in a malfunction in high-density systems. Recently, zirconium titanate thin films were discovered to have very interesting dielectric properties, which suggests a use for them in microwave integrated systems, such as receivers or DRAMs, since they are monophasic, have little dissipation and show a good thermal stability and a high value for the dielectric constant, independent of frequency in the range from kilohertz to a few gigahertz. Real application is possible only in strict connection with the development of a suitable preparation method which allows production with controlled and reproducible characteristics. In this work, the synthesis and characterization of Zr_xTi_1-xO₄ (ZT) thin films grown via MO-CVD is described, studying the influence of growth parameters on their structural, chemical and physical properties. Received: 17 June 2002 / Accepted: 24 June 2002 / Published online: 4 November 2002 RID="*" ID="*"Corresponding author. Fax: +39-06/9067-2445, E-mail: Pad@mlib.cnr.it     

Buffer effects of Ag layers on magneto-optical Co/Ge(1 0 0) ultrathin films

Magnetic properties of the Co/Ag/Ge(1 0 0) films grown at room temperature and 200 K were studied by the surface magneto-optical Kerr effect (SMOKE). More than 1.5 monolayer Ag buffer layers not only effectively block the interdiffusion between the capped Co layers and the Ge(1 0 0) substrate but also stabilize the magnetic phase. The temperature and thickness dependence on coercivity measurements show that interactions upon the interfaces are strongly correlated to the microstructures.     

Thermal stability of nanoscale silver metallization in Ag/W/Co/Si(1 0 0) multilayer

In this work, we have studied thermal stability of nanoscale Ag metallization and its contact with CoSi₂ in heat-treated Ag(50 nm)/W(10 nm)/Co(10 nm)/Si(1 0 0) multilayer fabricated by sputtering method. To evaluate thermal stability of the systems, heat-treatment was performed from 300 to 900 °C in an N₂ ambient for 30 min. All the samples were analyzed by four-point-probe sheet resistance measurement (R_s), Rutherford backscattering spectrometry (RBS), X-ray diffractometry (XRD), and atomic force microscopy (AFM). Based on our data analysis, no interdiffiusion, phase formation, and R_s variation was observed up to 500 °C in which the Ag layer showed a (1 1 1) preferred crystallographic orientation with a smooth surface and R_s of about 1 Ω/□. At 600 °C, a sharp increase of R_s value was occurred due to initiation of surface agglomeration, WSi₂ formation, and interdiffusion between the layers. Using XRD spectra, CoSi₂ formed at the Co/Si interface preventing W silicide formation at 750 and 800 °C. Meantime, RBS analysis showed that in this temperature range, the W acts as a cap layer, so that we have obtained a W encapsulated Ag/CoSi₂ contact with a smooth surface. At 900 °C, the CoSi₂ layer decomposed and the layers totally mixed. Therefore, we have shown that in Ag/W/Co/Si(1 0 0) multilayer, the Ag nano-layer is thermally stable up to 500 °C, and formation of W-capped Ag/CoSi₂ contact with R_s of 2 Ω/□ has been occurred at 750-800 °C.     

Raman spectroscopic studies of PbxLa1−xTi1−x/4O3 thin films grown on Si substrates by RF magnetron sputtering

A systematic spectroscopic investigation of Pb_xLa_1−xTi_1−x/4O₃ (PLT) thin films grown on PbO_x/Pt/Ti/SiO₂/Si substrate by RF magnetron sputtering was performed by using confocal Raman spectroscopy. Influence of the growth condition modification including different growth temperatures, with various buffer layer thickness, and post-annealing treatments were analyzed with taking advantages of the corresponding Raman spectral band variation in the respective process. Significant change in the spectral bands occurred with the alteration of the growth condition, and the related mechanisms were discussed after spectral deconvolution, providing reliable information about the direction for film growth.     

Surface morphology of highly mismatched InSb films grown on GaAs substrates by molecular beam epitaxy

InSb films on GaAs(001) substrates with and without GaAs buffer layer have been grown by molecular beam epitaxy. Rather than surface undulations, aligned ripples and pyramidal hillocks along the orthogonal 〈110〉 directions were observed on the surface of InSb films. Both the preferential growth and the termination of ripples were proved to be related to strain‐driven mass transport. A model was proposed to elucidate the formation of the hillocks, which are more efficient to relax strain than ripples. Due to the strain relaxation through hillocks with small bases predominantly, the surfaces of the InSb films grown without a GaAs buffer layer are smoother than those of films grown with a GaAs buffer layer. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

GaN epilayers on nanopatterned GaN/Si(1 1 1) templates: Structural and optical characterization

Template-based nanoscale epitaxy has been explored to realize high-quality GaN on Si(1 1 1) substrates. We have employed polystyrene-based nanosphere lithography to form the nano-hole array patterns on GaN/Si(1 1 1) template and then, subsequent regrowth of GaN is carried out by metalorganic chemical vapor deposition (MOCVD). During the initial growth stage of GaN on such nanopatterned substrates, we have observed formation of nanoislands with hexagonal pyramid shape due to selective area epitaxy. With further epitaxial regrowth, these nanoislands coalesce and form continuous GaN film. The overgrown GaN on patterned and non-patterned regions is characterized by high-resolution X-ray diffraction (HRXRD) and high-spatial resolution optical spectroscopic methods. Micro-photoluminescence (PL), micro-Raman scattering and scanning electron microscopy (SEM) have been used to assess the microstructural and optical properties of GaN. Combined PL and Raman data analyses show improved optical quality when compared to GaN simultaneously grown on non-patterned bulk Si(1 1 1). Such thicker GaN templates would be useful to achieve III-nitride-based opto- and electronic devices integrated on Si substrates.     

Effect of substrate temperature and annealing temperature on the structural, electrical and microstructural properties of thin Pt films by rf magnetron sputtering

Influence of both substrate temperature, T_s, and annealing temperature, T_a, on the structural, electrical and microstructural properties of sputtered deposited Pt thin films have been investigated. X-ray diffraction results show that as deposited Pt films (T_s = 300, 400 °C) are preferentially oriented along (1 1 1) direction. A little growth both along (2 0 0) and (3 1 1) directions are also noticed in the as deposited Pt films. After annealing in air (T_a = 500-700 °C), films become strongly oriented along (1 1 1) plane. With annealing temperature, average crystallite size, D, of the Pt films increases and micro-strain, e, and lattice constant, a₀, decreases. Residual strain observed in the as deposited Pt films is found to be compressive in nature while that in the annealed films is tensile. This change in the strain from compressive to tensile upon annealing is explained in the light of mismatch between the thermal expansion coefficients of the film material and substrate. Room temperature resistivity of Pt films is dependant on both the T_s and T_a of the films. Observed decrease in the film resistivity with T_a is discussed in terms of annihilation of film defects and grain-boundary. Scanning electron microscopic study reveals that as the annealing temperature increases film densification improves. But at an annealing temperature of ∼600 °C, pinholes appear on the film surface and the size of pinhole increases with further increase in the annealing temperature. From X-ray photoelectron spectroscopic analysis, existence of a thin layer of chemisorbed atomic oxygen is detected on the surfaces of the as deposited Pt films. Upon annealing, coverage of this surface oxygen increases.     

Formation mechanisms of GaN nanorods grown on Si(1 1 1) substrates

Scanning electron microscopy (SEM) images, transmission electron microscopy (TEM) images, and selected-area electron diffraction (SAED) patterns showed that vertically well aligned GaN nanorods with c-axis-oriented crystalline wurzite structures were grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy. The high-resolution TEM (HRTEM) images showed that the crystallized GaN nanorods contained very few defects and that they were consisted of , {0 0 0 1}, and { } facets. The formation mechanisms for the GaN nanorods grown on Si(1 1 1) substrates are described on the basis of the SEM, TEM, SAED pattern, and HRTEM results.     

Optimization of VI/II pressure ratio in ZnTe growth on GaAs(0 0 1) by molecular beam epitaxy

ZnTe epilayers were grown on GaAs(0 0 1) substrates by molecular beam epitaxy (MBE) at different VI/II beam equivalent pressure (BEP) ratios (R_VI/II) in a wide range of 0.96-11 with constant Zn flux. Based on in situ reflection high-energy electron diffraction (RHEED) observation, two-dimensional (2D) growth mode can be formed by increasing the R_VI/II to 2.8. The Te/Zn pressure ratios lower than 4.0 correspond to Zn-rich growth state, while the ratios over 6.4 correspond to Te-rich one. The Zn sticking coefficient at various VI/II ratios are derived by the growth rate measurement. The ZnTe epilayer grown at a R_VI/II of 6.4 displays the narrowest full-width at half-maximum (FWHM) of double-crystal X-ray rocking curve (DCXRC) for (0 0 4) reflection. Atomic force microscopy (AFM) characterization shows that the grain size enlarges drastically with the R_VI/II. The surface root-mean-square (RMS) roughness decreases firstly, attains a minimum of 1.14 nm at a R_VI/II of 4.0 and then increases at higher ratios. It is suggested that the most suitable R_VI/II be controlled between 4.0 and 6.4 in order to grow high-quality ZnTe epitaxial thin films.     

Electric field dependence of topography in ferroelectric P(VDF/TrFE) films

The effect of electric fields on the topography and structures in P(VDF/TrFE) ferroelectric films was studied. The morphological changes after poling treatment at 25 °C, from previously chrysanthemum-like structures to regular and parallel slug-like domains, were observed by scanning probe microscope. Poling process at higher temperature induced even greater morphological changes. Imaging of local electrical properties showed that these changes could not be attributed to the influence of local charges injected into film surface during poling process. It was believed that this new morphology came from the reform of film structures induced by electric fields.