Comparison of the influence of the fictive and the annealing temperature on the UV-transmission properties of synthetic fused silica

′ and NBOH). Samples with high OH content exhibit gradual recovery from the absorption band within several minutes after exposure to the KrF laser radiation. The formation of the KrF laser-induced 210 nm absorption band depends on the fictive temperature and on the OH content. Low fictive temperature, as a measure for the number of intrinsic defects, retards E^′ generation at the beginning of intense KrF excimer laser irradiation when the majority of defects are generated from precursor defects. However, for longer irradiation periods with pulse numbers of the order of 10⁵ pulses, a high OH content is the beneficial parameter. The accompanying atomic hydrogen is essential for the suppression of the 210 nm absorption band. This happens by transformation of the E^′ centers into Si-H defects. In contrast to a generally held view, annealing (decreasing of the fictive temperature) of fused silica does not always reduce UV induced defect generation. For example, annealing of the samples in an argon atmosphere causes a significantly higher 210 nm absorption increase during KrF excimer laser irradiation (240000 pulses) compared to nonannealed samples. Two spectroscopic methods to determine the OH content of fused silica were applied: Raman and infrared spectroscopy, which in this work lead to differing results. The energetics of the 210 nm absorption band generation and bleaching is summarized by a diagram explaining the interaction of the 248 nm laser radiation with fused silica. Received: 2 June 1997/Accepted: 13 June 1997     

Minireview: The compact phase in polymers and proteins

Proteins are linear molecules. However, the simple model of a polymer viewed as spheres tethered together does not account for many of the observed characteristics of protein structures. Here we review some recent works tackling this problem. In particular, we will show that there is a growing evidence suggesting that the compact structures of folded proteins are selected in their gross topological features based on geometry and symmetry rather than on sequence consideration. They are poised at the edge of compaction, thus accounting for their flexibility. Different aspects of protein behavior can be rationalized by studying how the energy landscape of a single chain in the marginally compact phase can be modified.     

Surface modification of zinc oxide nanoparticle by PMAA and its dispersion in aqueous system

Commercial zinc oxide nanoparticles were modified by polymethacrylic acid (PMAA) in aqueous system. The hydroxyl groups of nano-ZnO particle surface can interact with carboxyl groups (COO-) of PMAA and form poly(zinc methacrylate) complex on the surface of nano-ZnO. The formation of poly(zinc methacrylate) complex was testified by Fourier-transform infrared spectra (FT-IR). Thermogravimetric analysis (TGA) indicated that PMAA molecules were absorbed or anchored on the surface of nano-ZnO particle, which facilitated to hinder the aggregation of nano-ZnO particles. Through particle size analysis and transmission electron micrograph (TEM) observation, it was found that PMAA enhanced the dispersibility of nano-ZnO particles in water. The dispersion stabilization of modified ZnO nanoparticles in aqueous system was significantly improved due to the introduction of grafted polymer on the surface of nanoparticles. The modification did not alter the crystalline structure of the ZnO nanoparticles according to the X-ray diffraction patterns.     

Anomalous photoluminescence and raman scattering behavior in heavily Mg+ ion-implanted InP

Mg⁺ ions were implanted into highly pure InP grown by the liquid encapsulated Czochralski (LEC) method in which the Mg concentration [Mg] was varied between 1×10¹⁵ cm^–3 and 3×10²⁰ cm^–3. Two annealing methods were used: furnace annealing (FA) up to 740° C and flash lamp annealing (rapid thermal annealing, RTA) up to 900° C. For characterization, photoluminescence (PL) spectra were measured between 2K and room temperature together with Raman scattering measurements at room temperature. An emission designated by g, which was attributed to a novel energy state of an isolated acceptor, was found to be produced for a rather low value of [Mg]. In addition, a broad emission denoted by [g–g], which was ascribed to acceptor-acceptor pairs, was observed below bound exciton emissions for moderate values of [Mg]. These features were quite similar to those previously observed in acceptor-doped GaAs when the background concentration of donors is extremely low. Two additional novel emissions located far below the band-to-acceptor emission were also obtained, and each showed a remarkable energy shift towards lower energy with increasing [Mg]. The binding energies of these emissions were estimated from the temperature dependence of PL spectra and the results suggest that they are complex-type radiative recombination centers, presumably donor-acceptor-type centers. A strong broad emission centered near the band-to-acceptor emission was observed for [Mg]=3×10²⁰ cm^–3. This observation indicates a formation of a new material between In, P and Mg, which was also attested by the appearance of a new TO-like Raman signal for [Mg] greater than 1×10¹⁹ cm^–3. A substantial difference of PL and Raman spectra was revealed for the two annealing methods, suggesting that the annealing behaviour of ion-implanted InP should be investigated more extensively in order to establish reliable annealing procedures.Dedicated to H.-J. Queisser on the occasion of his 60th birthday     

Femtosecond waveguide writing: a new avenue to three-dimensional integrated optics

Using tightly focussed femtosecond laser pulses, waveguides can be fabricated inside various glasses and crystals. This technique has the potential to generate not only planar but three-dimensional photonic devices. In this paper we present, to the best of our knowledge, the first true three-dimensional integrated optical device, a 1×3 splitter fabricated in pure fused silica. The optical properties of this device and possibilities for the fabrication of complex high-density integrated optical elements are discussed. Received: 23 December 2002 / Accepted: 6 January 2003 / Published online: 28 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-3641/65-7680, E-mail: nolte@iap.uni-jena.de     

N+BF<Subscript>2</Subscript> and N+C+BF<Subscript>2</Subscript> high-dose co-implantation in silicon

Nitrogen and boron BF₂, and nitrogen, carbon, and boron BF₂ high-dose (6×10¹⁶–3×10¹⁷ cm^-2) co-implantation were performed at energies of about 21–77 keV. Subsequent high-temperature annealing processes (600, 850, and 1200 °C) lead to the formation of three and two surface layers respectively. The outer layer mainly consists of polycrystalline silicon and some amorphous material and Si₃N₄ inclusions. The inner layer is highly defective crystalline silicon, with some inclusions of Si₃N₄ too. In the N+B-implanted sample the intermediate layer is amorphous. Co-implantation of boron with nitrogen and with nitrogen and carbon prevents the excessive diffusivity of B and leads to a lattice-parameter reduction of 0.7–1.0%. Received: 10 January 2002 / Accepted: 30 May 2002 / Published online: 4 November 2002 RID="*" ID="*"Corresponding author. Fax: +34-91/3974895; E-mail: Lucia.Barbadillo@uam.es     

Effects of NH3, O2, and N2 co-implantation on Cu out-diffusion and antimicrobial properties of copper plasma-implanted polyethylene

Metal antibacterial reagents are effective in the enhancement of the antimicrobial properties of medical polymers. However, incorporation of metal antibacterial reagents into polymers using conventional methods usually results in unstable antimicrobial effects. Our previous research demonstrates that plasma immersion ion implantation (PIII) can be used to effectively incorporate metal antibacterial reagents such as Cu into polyethylene (PE) in the near surface region up to several hundred nanometers without causing noticeable damage to the polymer matrix. In this work, various gases including NH₃, O₂, and N₂ were plasma-implanted in concert with Cu plasma immersion ion implantation to study the effects of these gas species on the release rate of Cu from the substrate. Our experimental results reveal that the copper depth profiles are not affected significantly by NH₃, O₂, or N₂ co-implantation and these gas elements have similar depth profiles as Cu. Chemical analyses demonstrate that polar functional CO, CO, CN, CN, and CN bonds formed in the substrate play an important role in regulating Cu out-diffusion. Among the three gas species, N₂ shows the best effects in regulating Cu out-diffusion and produces the best long term antibacterial properties. The Cu retention and out-diffusion mechanism in the ion-implanted polyethylene is described.     

Diffusion-induced growth of compositional heterogeneity in polymer blends containing random copolymers

The compositional relaxation in random copolymer systems on a macroscopic scale is considered in theory. A set of diffusion equations is derived that describes the motion of chains of different composition and then converted into coupled equations for statistical moments of the compositional distribution. Several ways to solve the closure problem for these equations are discussed. The simplest is the situation when the shape of the transient compositional distribution can be predicted a priori, for example, a bimodal distribution is kept during interdiffusion of two copolymers that are not very close in composition. For a general case, it is shown that the cumulant-neglect closure based on the truncation of high-order cumulants is an effective method to get an approximate solution in terms of the time-dependent local mean composition and its dispersion. This method is applied to non-homogeneous compatible polymer systems, such as a random copolymer AB of a composition varying in space, a bilayer of Bernoullian copolymers AB of different composition, and a bilayer of homopolymers A and B, in which an autocatalytic polymer-analogous reaction A → B takes place, with possibility of the neighbor group effect. It is found that the interdiffusion can lead to a substantial broadening of the local compositional distribution, which, in turn, accelerates the system dynamics and promotes chemical reactions.     

Elasticity transition and loop formation in vibrated bead chains: A simulation of polymer chains

By measuring the distribution function of the end-to-end distance, we find that strongly shaken bead chains exhibit many properties, such as the rigid-rod-to-Gaussian chain transition, scaling, fast drop of loop formation probability in the short-chain regime, and enhancement of loop formation probability for kinked chains, of long-chain polymers. Though there is difference in local details between our chains and the worm-like chains, our results are consistent with recent calculations based on the worm-like chain model in many respects.     

Raman study on vapor-phase equilibrated Er:LiNbO3 and Er:Ti:LiNbO3 crystals

Raman spectra of Er:LiNbO₃ crystal and Ti-diffusedEr:LiNbO₃ strip waveguide, in which the Li/Nb ratio was altered using a vapor-phase equilibration (VPE) technique, were measured at room temperature in the wave-number range 50–3500 cm^-1. Both 488 and 514.5 nm radiations were used to excite Raman scattering, A₁(TO) and E(TO) modes were recorded at backward scattering geometry. The results indicated that the lattice vibrational spectra of the as-grown Er:LiNbO₃ are almost the same as those of pure LiNbO₃ except for the little shift of the peak position and the change of relative intensity of some peaks. In comparison with the spectra of as-grown Er:LiNbO₃ crystal the vapor-phase equilibrated Er:LiNbO₃ and Er:Ti:LiNbO₃ crystals in the lattice vibrational region exhibit the following features: firstly, Raman peaks become narrow, indicating that the VPE process has brought Er:LiNbO₃ and Er:Ti:LiNbO₃ crystals closer to a stoichiometric composition; secondly, relative intensity of some peaks varies with the VPE time; and finally, slight blue shifting in peak position was observed. Some of these features were correlated with the NbO₆ octahedra and with the site distribution of the doped Er ions. In addition, green fluorescence peaks and/or bands associated with the electron transitions ² H _11/2?⁴ I _15/2 and ⁴ S _3/2?⁴ I _15/2 of the doped Er³⁺ were also observed. For 488 nm excitation they appear in the wavenumber range of 1200–3000 cm^-1 and are well separated from lattice vibrational region; for 514.5 nm excitation, however, these fluorescence peaks shift towards the low wavenumber region and overlap partially with the lattice vibrational spectra. Received: 24 May 2000 / Accepted: 29 May 2000 / Published online: 13 September 2000     

Relative roles of acetic acid, dodecyl sulfate and benzotriazole in chemical mechanical and electrochemical mechanical planarization of copper

The efficiency of chemical mechanical or electrochemical mechanical planarization (CMP or ECMP) carried out in the fabrication of integrated circuits is largely governed by the functional chemicals used in these processes. In this work, we study the individual and combined chemical and electrochemical effects of a selected set of such chemicals that can potentially support both CMP and ECMP of copper. These chemicals include acetic acid (HAc) as a complexing agent, H2O2 as an oxidizer, and ammonium dodecyl sulfate (ADS) as a dissolution inhibitor. Surface passivating effects of ADS under both CMP (open circuit) and ECMP (voltage activated) conditions are compared with those of a standard dissolution inhibitor for Cu, benzotriazole (BTAH), and the combined effects of a BTAH-ADS mixture also are explored. The experiments are performed in the absence of mechanical polishing using static and rotating Cu disc electrodes, and electro-dissolution of Cu for ECMP is activated using a voltage pulse modulation technique. A mechanism of surface reactions is proposed to describe the relative roles of HAc, H2O2, ADS and BTAH as electrolyte components for CMP and ECMP of Cu.     

Preparation, structural and photoluminescent properties of CeO2:Eu films derived by Pechini sol-gel process

In this study, CeO₂ and CeO₂:Eu films were prepared by a simple Pechini sol-gel process and dip-coating method. CeO₂ were successfully synthesized by hydrolysis of cerium nitrate. Thermogravimetric analysis was used to study the thermal chemical properties of sol-gel powder. Structural properties of CeO₂ films annealed at different temperature ranging from 400 to 900 °C were investigated by X-ray diffraction, field emission scanning electron microscopy, and Fourier transform infrared spectroscopy. Luminescent properties of CeO₂:Eu³⁺ films were investigated by excitation and emission spectra. Our results show that CeO₂ is a good host material for rare earth ions doping and Pechini sol-gel process is a useful method to derive high quality, macrocrack free, pure and doped CeO₂ films.     

Depletion effect on partial organization of atactic polymer chain segments in microcells

Glass transition for atactic poly(methyl methacrylate) (a-PMMA) prepared in nano-cells by microemulsion polymerization was measured at a faster heating rate after slow cooling of the sample from a temperature above T_g. An additional enthalpy relaxation and glass transition were observed at higher temperatures for the a-PMMA sample due to the partial organization of the chain segments which occurred during microemulsion polymerization. The re-precipitated a-PMMA did not show any self-organization under the same thermal conditions, although there are no changes in molecular weight or tacticity of the polymer chains. A depletion-interaction phenomenon was understood to provide entropic force for the self-organization of polymer chains inside the walls of the microemulsion cells.     

Middle-infrared random lasing of Cr doped ZnSe, ZnS, CdSe powders, powders imbedded in polymer liquid solutions, and polymer films

Room temperature (RT) middle-infrared (Mid-IR) random lasing of chromium- (Cr) doped ZnSe, ZnS, and CdSe powders, powders imbedded in perfluorocarbon liquid polymer solutions, and fluorocarbon polymer films is reported. Laser active powders were prepared without a stage of bulk crystal growth by annealing of starting chemicals (pure, mixed ZnSe:CrSe; ZnS:CrS; CdSe:CrSe). Mixture of the different semiconductor hosts allows tuning oscillation wavelength from 2240 to 2630 nm.     

Characteristic variations in the effect of diluents on polymer crystallization and melting observed for a sample of poly(ethylene-co-octene)

Melting points in mixtures of a crystallizable polymer with a low-molar-mass diluent depend on both, the diluent fraction and the crystal thickness. A differentiation of the two factors can be achieved by temperature-dependent SAXS experiments. A corresponding study, complemented by DSC, dilatometry, microscopy and AFM-imaging, was carried out for mixtures of a poly(ethylene-co-octene) with n-C₁₆H₃₄, c-C₁₆H₃₂ and methyl-anthracene, respectively. All diluents lead for a constant crystal thickness to melting point depressions in agreement with Raoult's law. On the other hand, the effect of the diluents on the thickness of the crystals formed at a fixed crystallization temperature varies. While in the presence of the two alkanes thicker crystals form, no effect arises for the methyl-anthracene—as was previously found for the octene-co-units. We consider these observations as a further support for our view that polymer crystallization follows a multi-stage route which includes a passage through an intermediate mesomorphic phase. Under such conditions crystal thicknesses would only be affected if the diluent is still present in the mesomorphic phase and stay invariant if the diluent molecules are already rejected when this intermediate phase forms.     

Complex permittivity and microwave absorption properties of carbon nanotubes/polymer composite: A numerical study

Based on an equivalent resistance-capacitance (RC) network, we investigate theoretically the complex permittivity and microwave absorption properties of carbon nanotubes (CNTs)/polymer composite in the frequency range of 50 MHz-3 GHz using the logarithmic mixing rule. Both the real and imaginary parts of the permittivities of CNTs and polymer are considered in detail. The simulated results show that the real and imaginary permittivities of the composite increase explicitly with increasing volume fraction of CNTs, and the latter is more sensitive. The calculated complex permittivity spectra of the composite are in good agreement with the available experimental data. In addition, a good linear relationship between microwave absorbance and frequency is found.     

Wigner time delay and related concepts: Application to transport in coherent conductors

The concepts of Wigner time delay and Wigner–Smith matrix allow us to characterise temporal aspects of a quantum scattering process. The paper reviews the statistical properties of the Wigner time delay for disordered systems; the case of disorder in 1D with a chiral symmetry is discussed and the relation with exponential functionals of the Brownian motion is underlined. Another approach for the analysis of time delay statistics is the random matrix approach, from which we review few results. As a practical illustration, we briefly outline a theory of non-linear transport and AC transport developed by Büttiker and coworkers, where the concept of Wigner–Smith time delay matrix is a central piece allowing us to describe screening properties in out-of-equilibrium coherent conductors.     

Excitation process and photoluminescence properties of Tb and Eu ions in SnO2 and in SnO2: Porous silicon hosts

Tin oxide (SnO₂)-layers-doped terbium and europium ions are elaborated by the sol-gel method on silicon substrates. After annealing at 500 °C, the transmission electron microscopy revealed a crystallization of tin oxide.The emission properties of rare-earth in SnO₂ are studied systematically against temperature annealing and Tb³⁺ concentration. The PL spectrum is optimal after annealing at 900 °C and the corresponding photoluminescence (PL) decay is nearly exponential, showing that the sample is homogenous and the PL process can be described by two levels system.The concentration effect shows a quenching of the PL intensity for Tb³⁺ concentration above 4%. From the investigation of the decay rate from the ⁷F₅ state within terbium concentration, we show that self-quenching is insured by dipole - dipole interaction. The evolutions of both PL intensity and PL lifetime versus temperature are studied. The PL intensity and PL lifetime are enhanced by deposing SnO₂:Tb³⁺ and SnO₂:Eu³⁺ in porous silicon. We show that an efficient excitation transfer from Si nanocrystallites to RE ions can occur.     

Percolation in a network with long-range connections: Implications for cytoskeletal structure and function

Cell shape, signaling, and integrity depend on cytoskeletal organization. In this study we describe the cytoskeleton as a simple network of filamentary proteins (links) anchored by complex protein structures (nodes). The structure of this network is regulated by a distance-dependent probability of link formation as P=p/d^s, where p regulates the network density and s controls how fast the probability for link formation decays with node distance (d). It was previously shown that the regulation of the link lengths is crucial for the mechanical behavior of the cells. Here we examined the ability of the two-dimensional network to percolate (i.e. to have end-to-end connectivity), and found that the percolation threshold depends strongly on s. The system undergoes a transition around s=2. The percolation threshold of networks with s<2 decreases with increasing system size L, while the percolation threshold for networks with s>2 converges to a finite value. We speculate that s<2 may represent a condition in which cells can accommodate deformation while still preserving their mechanical integrity. Additionally, we measured the length distribution of F-actin filaments from publicly available images of a variety of cell types. In agreement with model predictions, cells originating from more deformable tissues show longer F-actin cytoskeletal filaments.