Pulsed-laser deposition of smooth thin films of Er, Pr and Nd doped glasses

Thin films of complex oxides have been obtained by pulsed-laser deposition (PLD) from glass targets belonging to the system Li₂O-Al₂O₃-P₂O₅-(RE)₂O₃, with RE = Nd, Pr, Er. The films were deposited on quartz, silicon and ITO/glass substrates using a F₂ laser (λ = 157 nm, ι ≈ 20 ns) for ablation in vacuum. The structural, morphological and optical properties of the oxide films were investigated through IR and UV-VIS spectroscopy, Atomic Force Microscopy (AFM), Scanning Electron Microscopy, Energy Dispersive X-ray Spectroscopy (SEM-EDX) and Spectroscopic Ellipsometry. The laser wavelength was found to be the key parameter to obtain thin films with very smooth surface. In this way new possibilities are opened to grow multilayer structures for photonic applications.     

Crystallization and electrical properties of V2O5 thin films prepared by RF sputtering

V₂O₅ thin films were prepared under various conditions by using reactive RF sputtering technique. The microstructure and electrical properties of the films are have been investigated. X-ray diffraction data revealed the films deposited at low O₂/Ar ratio are amorphous. The orthorhombic structure of film improved after post annealing at 873 K. The microstructure parameters (crystallite/domain size and macrostrain) have been evaluated by using a single order Voigt profile method. Using the two-point probe technique, the dark conductivity as a function of the condition parameters such as film thickness, oxygen content and temperature are discussed. It was also found that, the behaviour of ρd versus d was found to fit properly with the Fuchs-Sondheimer relation with the parameters: ρ_o = 2.14 × 10⁷ Ω cm and ?_o = 112 ± 2 nm. At high temperature, the electrical conductivity is dominated by grain boundaries, the values of activation energy and potential barrier height were 0.90 ± 0.02 eV and 0.92 ± 0.02 V, respectively.     

Properties of Dy-doped ZnO nanocrystalline thin films prepared by pulsed laser deposition

Highly transparent conductive Dy₂O₃ doped zinc oxide (ZnO)_1-x(Dy₂O₃)_x nanocrystalline thin films with x from 0.5% to 5% have been deposited on glass substrate by pulsed laser deposition technique. The structural, electrical and optical properties of Dy₂O₃ doped thin films were investigated as a function of the x value. The experimental results show that the Dy concentration in Dy-doped ZnO thin films has a strong influence on the material properties especially electrical properties. The resistivity decreased to a minimum value of 5.02 × 10⁻⁴ Ω cm with x increasing from 0.5% to 1.0%, then significantly increased with the further increasing of x value. On the contrary, the optical direct band gap of the (ZnO)_1-x(Dy₂O₃)_x films first increased, then decreased with x increasing. The average transmission of Dy₂O₃ doped zinc oxide films in the visible range is above 90%.     

Particulate assisted growth of ZnO nanorods and microrods by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on the gallium nitride (GaN) and sapphire (Al₂O₃) substrates by pulsed laser deposition (PLD) without using any metal catalyst. The experiment was carried out at three different laser wavelengths of Nd:YAG laser (λ = 1064 nm, λ = 532 nm) and KrF excimer laser (λ = 248 nm). The ZnO films grown at λ = 532 nm revealed the presence of ZnO nanorods and microrods. The diameter of the rods varies from 250 nm to 2 μm and the length varies between 9 and 22 μm. The scanning electron microscopy (SEM) images of the rods revealed the absence of frozen balls at the tip of the ZnO rods. The growth of ZnO rods has been explained by vapor-solid (V-S) mechanism. The origin of growth of ZnO rods has been attributed to the ejection of micrometric and sub-micrometric sized particulates from the ZnO target. The ZnO films grown at λ = 1064 nm and λ = 248 nm do not show the rod like morphology. X-ray photoelectron spectroscopy (XPS) has not shown the presence of any impurity except zinc and oxygen.     

Structural and optical characterization of undoped, doped, and clustered ZnO thin films obtained by PLD for gas sensing applications

The synthesis by pulsed laser deposition technique of zinc oxide thin films suitable for gas sensing applications is herein reported. The ZnO targets were irradiated by an UV KrF^* (λ = 248 nm, τ_FWHM ∼7 ns) excimer laser source, operated at 2.8 J/cm² incident fluence value, whilst the substrates consisted of SiO₂(0 0 1) wafers heated at 150 °C during the thin films growth process. The experiments were performed in an oxygen dynamic pressure of 10 Pa. Structural and optical properties of the thin films were investigated. The obtained results have demonstrated that the films are c-axis oriented. Their average transmission in the visible-infrared spectral region was found to be about 85%. The equivalent refractive indexes and extinction coefficients were very close to those of the tabulated reference values. Doping with 0.5% Au and coating with 100 pulses of Au clusters caused but a very slight decrease (with a few percent) of both transmission and refractive index values. The coatings with the most appropriate optical properties as waveguides have been selected and their behavior was tested for butane sensing.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Periodicity and orientation dependence of electrical properties of [(Pb0.90La0.10)Ti0.975O3/PbTiO3]n (n = 1-6) multilayer thin films

The [(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃]_n (PLT/PT)_n (n = 1-6) multilayer thin films were deposited on the PbO_x(1 0 0)/Pt/Ti/SiO₂/Si substrates by RF magnetron sputtering method. The layer thickness of PbTiO₃ in one periodicity kept unchanged, and the layer thickness of (Pb_0.90La_0.10)Ti_0.975O₃ is varied. The electrical properties of the (PLT/PT)_n multilayer thin films were investigated as a function of the periodicity (n) and the orientation. The studied results show that the PbO_x buffer layer results in the (PLT/PT)_n films’ (1 0 0) orientation, and the (1 0 0)-oriented (PLT/PT)_n multilayer thin films with n = 2 exhibit better pyroelectric properties and ferroelectric behavior than those of (PLT/PT)_n films with other periodicities and orientations. The underlying physical mechanism for the enhanced electrical properties of (PLT/PT)_n multilayer thin films was carefully discussed in terms of the periodicities and orientations.     

Fabrication and characterization of La-doped HfO2 gate dielectrics by metal-organic chemical vapor deposition

La-doped HfO₂ gate dielectric thin films have been deposited on Si substrates using La(acac)₃ and Hf(acac)₄ (acac = 2,4-pentanedionate) mixing sources by low-pressure metal-organic chemical vapor deposition (MOCVD). The structure, thermal stability, and electrical properties of La-doped HfO₂ films have been investigated. Inductive coupled plasma analyses confirm that the La content ranging from 1 to 5 mol% is involved in the films. The films show smaller roughness of ∼0.5 nm and improved thermal stability up to 750 °C. The La-doped HfO₂ films on Pt-coated Si and fused quartz substrates have an intrinsic dielectric constant of ∼28 at 1 MHz and a band gap of 5.6 eV, respectively. X-ray photoelectron spectroscopy analyses reveal that the interfacial layer is Hf-based silicate. The reliable value of equivalent oxide thickness (EOT) around 1.2 nm has been obtained, but with a large leakage current density of 3 A/cm² at V_g = 1V + V_fb. MOCVD-derived La-doped HfO₂ is demonstrated to be a potential high-k gate dielectric film for next generation metal oxide semiconductor field effect transistor applications.     

Formation of highly textured (1 1 1) Bi2O3 films by anodization of electrodeposited bismuth films

Highly textured bismuth oxide (Bi₂O₃) thin films have been prepared using anodic oxidation of electrodeposited bismuth films onto stainless steel substrates. The Bi₂O₃ films were uniform and adherent to substrate. The Bi₂O₃ films were characterized for their structural and electrical properties by means of X-ray diffraction (XRD), electrical resistivity and dielectric measurement techniques. The X-ray diffraction pattern showed that Bi₂O₃ films are highly textured along (1 1 1) plane. The room temperature electrical resistivity of the Bi₂O₃ films was 10⁵ Ω cm. Dielectric measurement revealed normal oxide behavior with frequency.     

Pulsed laser deposition of fluoride glass thin films

The development of integrated waveguide lasers for different applications such as marking, illumination or medical technology has become highly desirable. Diode pumped planar waveguide lasers emitting in the green visible spectral range, e.g. thin films from praseodymium doped fluorozirconate glass matrix (called ZBLAN, owing to the main components ZrF₄, BaF₂, LaF₃, AlF₃ and NaF) as the active material pumped by a blue laser diode, have aroused great interest. In this work we have investigated the deposition of Pr:ZBLAN thin films using pulsed laser radiation of λ = 193 and λ = 248 nm. The deposition has been carried out on MgF₂ single crystal substrates in a vacuum chamber by varying both processing gas pressure and energy fluence. The existence of an absorption line at 210 nm in Pr:ZBLAN leads to absorption and radiative relaxation of the absorbed laser energy of λ = 193 nm preventing the evaporation of target material. The deposited thin films consist of solidified and molten droplets and irregular particulates only. Furthermore, X-ray radiation has been applied to fluoride glass targets to enhance the absorption in the UV spectral region and to investigate the deposition of X-ray treated targets applying laser radiation of λ = 248 nm. It has been shown that induced F-centres near the target surface are not thermally stable and can be easily ablated. Therefore, λ = 248 nm is not suitable for evaporation of Pr:ZBLAN.     

Dielectric properties of continuous composition spreaded MgO-Ta2O5 thin films

The dielectric properties of MgO-Ta₂O₅ continuous composition spread (CCS) thin films were investigated. The MgO-Ta₂O₅ CCS thin films were deposited on Pt/Ti/SiO₂/Si substrates by off-Axis RF magnetron sputtering system, and then the films were annealed at 350 °C with rapid thermal annealing system in vacuum. The dielectric constant and loss of MgO-Ta₂O₅ CCS thin films were plotted via 1500 micron-step measuring. The specific point of Ta₂O₅-MgO CCS thin film (post annealed at 350 °C) showing superior dielectric properties of high dielectric constant (k ∼ 28) and low dielectric loss (tan δ < 0⋅004) at 1 MHz were found in the area of 3-5 mm apart from Ta₂O₅ side on the substrate. The cation's composition of thin film was Mg:Ta = 0.4:2 at%.     

Vanadium-Al2O3 nanostructured thin films prepared by pulsed laser deposition: Optical switching

The formation and optical response of VO_x nanoparticles embedded in amorphous aluminium oxide (Al₂O₃) thin films by pulsed laser deposition is studied. The thin films have been grown by alternate laser ablation of V and Al₂O₃ targets, which has resulted in a multilayer structure with embedded nanoparticles. The V content has been varied by changing the number of pulses on the V target. It is found that VO_x nanoparticles with dimensions around 5 nm have been formed. The structural analysis shows that the vanadium nanoparticles are oxidized, although probably there is not a unique oxide phase for each sample. The films show a different optical response depending on their vanadium content. Optical switching as a function of temperature has been observed for the two films with the highest vanadium content, at transition temperatures of about −20 °C and 315 °C thus suggesting the presence of nanoparticles with compositions V₄O₇ and V₂O₅, respectively.     

Influence of substrate temperature and post-treatment on the properties of ZnO:Al thin films prepared by pulsed laser deposition

Highly transparent conductive Al₂O₃ doped zinc oxide (AZO) thin films have been deposited on the glass substrate by pulsed laser deposition technique. The effects of substrate temperature and post-deposition annealing treatment on structural, electrical and optical properties of AZO thin films were investigated. The experimental results show that the electrical resistivity of films deposited at 240 °C is 6.1 × 10⁻⁴ Ω cm, which can be further reduced to as low as 4.7 × 10⁻⁴ Ω cm by post-deposition annealing at 400 °C for 2 h in argon. The average transmission of AZO films in the visible range is 90%. The optical direct band gap of films was dependent on the substrate temperature and the annealing treatment in argon. The optical direct band gap value of AZO films increased with increasing annealing temperature.     

Effect of substrate temperature on structure and electrical resistivity of laser-ablated IrO2 thin films

IrO₂ thin films were prepared on Si(1 0 0) substrates by laser ablation. The effect of substrate temperature (T_sub) on the structure (crystal orientation and surface morphology) and property (electrical resistivity) of the laser-ablated IrO₂ thin films was investigated. Well crystallized and single-phase IrO₂ thin films were obtained at T_sub = 573-773 K in an oxygen partial pressure of 20 Pa. The preferred orientation of the laser-ablated IrO₂ thin films changed from (2 0 0) to (1 1 0) and (1 0 1) depending on T_sub. With the increasing of T_sub, both the surface roughness and crystallite size increased. The room-temperature electrical resistivity of IrO₂ thin films decreased with increasing T_sub, showing a low value of (42 ± 6) × 10⁻⁸ Ω m at T_sub = 773 K.     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

Enhanced electrical stability of flexible indium tin oxide films prepared on stripe SiO2 buffer layer-coated polymer substrates by magnetron sputtering

The electrical stability of flexible indium tin oxide (ITO) films fabricated on stripe SiO₂ buffer layer-coated polyethylene terephthalate (PET) substrates by magnetron sputtering was investigated by the bending test. The ITO thin films with stripe SiO₂ buffer layer under bending have better electrical stability than those with flat SiO₂ buffer layer and without buffer layer. Especially in inward bending text, the ITO thin films with stripe SiO₂ buffer layer only have a slight resistance change when the bending radius r is not less than 8 mm, while the resistances of the films with flat SiO₂ buffer layer and without buffer layer increase significantly at r = 16 mm with decreasing bending radius. This improvement of electrical stability in bending test is due to the small mismatch factor α in ITO-SiO₂, the enhanced interface adhesion and the balance of residual stress. These results indicate that the stripe SiO₂ buffer layer is suited to enhance the electrical stability of flexible ITO film under bending.     

Laser synthesis of thin layers of In4Se3, In4Te3 and modification of their structure and characteristics

Trends of structural modifications and phase composition occurring in In₄Se₃ thin films and In₄Se₃-In₄Te₃ epitaxial heterojunctions under laser irradiations have been investigated. Dynamics of the layer structure modification, depending on laser modes, i.e. pulse duration τ = 2-4 ms, irradiation intensity I₀ = 10-50 kW/cm², number of pulses N = 5-50, was studied by electron microscopy. An increase in laser influence promotes enlargement of the layer grains and transformation of their polycrystalline structure towards higher degree of stoichiometry. As a result of laser solid restructuring heterojunctions of In₄Se₃-In₄Te₃, being photosensitive within 1.0-2.0 μm and showing fast time of response, have been obtained. Laser modification of structure enables one to optimize electrical and optical properties of functional elements on the base of thin films and layers of In₄Se₃, In₄Te₃, widely used as infrared detectors and filters.     

Laser synthesis of nanostructures based on transition metal oxides

Nanostructures based on iron oxides in the form of thin films were synthesized while laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors (Fe(CO)₅) under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface with power density about 10² W/cm² and vapor pressure 666 Pa. Analysis of surface morphology and relief of the deposited films was carried out with scanning electron microscopy (SEM) and atomic force microscopy (AFM). This analysis demonstrated their cluster structure with average size no more than 100 nm. It was found out that the thicker the deposited film, the larger sizes of clusters with more oxides of higher oxidized phases were formed. The film thickness (d) was 10 and 28 nm. The deposited films exhibited semiconductor properties in the range 170-340 K which were stipulated by oxide content with different oxidized phases. The width of the band gap E_g depends on oxide content in the deposited film and was varied in the range 0.30-0.64 eV at an electrical field of 1.6 × 10³ V/m. The band gap E_g was varied in the range 0.46-0.58 eV at an electrical field of 45 V/m. The band gap which is stipulated by impurities in iron oxides E_i was varied in the range 0.009-0.026 eV at an electrical field of 1.6 × 10³ V/m and was varied in the range 0-0.16 eV at an electrical field 45 V/m. These narrow band gap semiconductor thin films displayed of the quantum dimensional effect.     

Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Structure and properties of transparent conductive doped ZnO films by pulsed laser deposition

High quality transparent conductive ZnO thin films were deposited on quartz glass substrates using pulsed laser deposition (PLD). We varied the growth conditions such as the substrate temperature and oxygen pressure. X-ray diffraction (XRD), X-ray photoelectron spectrometer (XPS), and atomic force microscopy (AFM) measurements were done on the samples. All films show n-type conduction, the best transparent conductive oxide (TCO) performance (Al-doped ZnO = 1.33 × 10⁻⁴ Ω cm, Ga-doped ZnO = 8.12 × 10⁻⁵ Ω cm) was obtained on the ZnO film prepared at pO₂ = 5 mTorr and T_s = 300 °C.