A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Optical and electrical properties of Y2O3 thin films prepared by ion beam assisted deposition

Y₂O₃ thin films were deposited by ion beam assisted deposition (IBAD) and the effects of fabrication parameters such as substrate temperature and ion energy on the structure, optical and electrical properties of the films were investigated. The results show that the deposited Y₂O₃ films had less optical absorption, larger refractive index, and better film crystallinity with the increase of substrate temperature or ion energy. The as-deposited Y₂O₃ films without ion-beam bombardment had larger relative dielectric constant (?_r) and the ?_r decreased with time even over by 40%, while the ?_r of films prepared with high ion energy had less changes, only less than 3%. Also, with the increase of ion energy, the electrical breakdown strength and the figure of merit increased.     

Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术，利用LSCO/CeO₂/YSZ多异质缓冲层，在Si(100)基 片上成功地制备了c轴一致取向的Bi_3.15Nd_0.85Ti₃O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构 、取向和形貌特征，考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响，确定 了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型 的蝴蝶形曲线，表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与 薄膜取向的相关性. 关键词： 3.15Nd_0.85Ti₃O₁₂')" href="#">Bi_3.15Nd_0.85Ti₃O₁₂ 铁电薄 膜 多层异质结 脉冲激光沉积     

Preparation and optical properties of ZnGa2O4:Cr thin films derived by sol-gel process

ZnGa₂O₄:Cr³⁺ thin films with bright red emission were synthesized using a sol-gel process, characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Auger electron spectroscopy (AES) and UV-vis and fluorescence spectrophotometry measurements. Effects of calcining temperature, film thickness, calcining duration and substrates on the crystal structure and photoluminescent property have been investigated. It is found that the crystallinity, Ga/Zn ratio and band gap energy (E_g) are significant factors influencing optical characteristics, while the nature of substrates affect the surface morphologies of ZnGa₂O₄:Cr³⁺ thin films.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Electronic properties of thin films of laser-ablated Al2O3

Laser ablation coupled to mass quadrupole spectrometry (LAMQS) has been used to prepare thin films of aluminum oxide deposited on Si substrates starting from commercial Al₂O₃ polycrystalline targets. X-ray photoemission (XPS) and reflection electron energy loss spectroscopy (REELS) have allowed the investigation of the electronic properties of the produced films. In particular, it was found that the Al/O atomic ratio assumes a value very near to 0.7 (stoichiometric ratio) only for films deposited normally with respect to the target surface, while films grown at larger deposition angles are more rich in oxygen content.The composition, the mass density, the optical energy gap, the complex dielectric function and refraction index of the films have been calculated and compared with the results obtained from our starting target material and with the literature. The morphology of the deposited samples has been analyzed by the AFM technique.     

Microstructure and electrical properties of Ba0.5Sr0.5TiO3 thin films prepared on copper foils with La2O3 buffer layers

Ba_0.5Sr_0.5TiO₃ (BST) thin films were deposited on copper foils via sol-gel method with La₂O₃ as a buffer layer. The films were processed in almost inert atmosphere so that the substrate oxidation was avoided while allowing the perovskite film phase to crystallize. The existence of a La₂O₃ buffer layer between the BST thin film and Cu foil improved the dielectric constant and reduced the leakage current density of the BST thin film. Meanwhile, the BST thin film exhibited ferroelectric character at room temperature, which was contrast to the para-electric behavior of the film without the buffer layer. Effects of La₂O₃ buffer layer on the crystallizability and microstructure of BST thin films were also investigated.     

Characterization of electrodeposited Bi2S3 thin films by holographic interferometry

Optical non destructive evaluation methods, using lasers as the object illumination source, include holographic interferometry. It is widely used to measure stress, strain, and vibration in engineering structures. Double exposure holographic interferometry (DEHI) technique is used to determine thickness and stress of electrodeposited bismuth trisulphide (Bi₂S₃) thin films for various deposition times. The same is tested for other concentration of the precursors. It is observed that, increase in deposition time, increases thickness of thin film but decreases stress to the substrate. The structural, optical and surface wettability properties of the as deposited films have been studied using X-ray diffraction (XRD), optical absorption and contact angle measurement, respectively. The X-ray diffraction study reveals that the films are polycrystalline with orthorhombic crystal structure. Optical absorption study shows the presence of direct transition with band bap 1.78 eV. The water contact angle measurement shows hydrophobic nature of Bi₂S₃ thin film surface.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

Preparation of Bi2S3 thin films with a nanoleaf structure by electrodeposition method

Nanoleaf-like Bi₂S₃ thin films were deposited on indium tin oxide (ITO) glass using Bi(NO₃)₃ and Na₂S₂O₃ as precursors by a cathodic electrodeposition process. The as-deposited thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and photoluminescence spectrum (PL). The influence of precursor solution mole concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] on the phase compositions, morphologies and photoluminescence properties of the obtained thin films were investigated. Results show that a uniform Bi₂S₃ thin film with nanoleaf structure can be obtained with the precursor solution concentration ratio [Bi(NO₃)₃]/[Na₂S₂O₃] = 1:7. The as-prepared thin films exhibit blue-green photoluminescence properties under ultraviolet light excitation. With the increase of concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] in the deposition solution, the crystallizations and PL properties of Bi₂S₃ thin films are obviously improved.     

Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.     

Influence of [S2O3]/[Sm] on Sm2S3 thin films deposited by liquid phase deposition method on self-assembled monolayers

Sm₂S₃ thin films were prepared on Si (1 0 0) substrates using SmCl₃ and Na₂S₂O₃ as precursors by liquid phase deposition method on self-assembled monolayers. The influence of the molar concentration ratio of [S₂O₃²⁻]/[Sm³⁺] on the phase compositions, surface morphologies and optical properties of the as-deposited films were investigated. The as-deposited Sm₂S₃ thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), ultraviolet-visible (UV-vis) and photoluminescence spectrum (PL). Results show that it is important to control the [S₂O₃²⁻]/[Sm³⁺] during the deposition process and monophase Sm₂S₃ thin films with orientation growth along (0 1 1) direction can be achieved when [S₂O₃²⁻]/[Sm³⁺] = 2.0, pH 3.0, with citric acid as a template agent. The as-deposited thin films exhibit a dense and crystalline surface morphology. Good transmittance in the visible spectrum and excellent absorbency of ultraviolet light of the thin films are observed, and the band gap of the thin films first decrease and then increase with the increase of the [S₂O₃²⁻]/[Sm³⁺]. The as-deposited thin films also exhibit red photoluminescence properties under visible light excitation. With the increase of the [S₂O₃²⁻]/[Sm³⁺] in the deposition solution, the PL properties of Sm₂S₃ thin films are obviously improved.     

Si基Bi4Ti3O12铁电薄膜的制备与特性研究

采用sol-gel工艺, 在分层快速退火的工艺条件下成功地制备了高质量Si基Bi_{4Ti3O12铁电薄膜. 研究了Si基Bi4Ti3O12薄膜的生长行为、铁电性能、C-V特性和疲劳特性. 研究表明: Si基Bi4Ti3O12薄膜具有随退火温度升高沿c轴择优生长的趋势; 退火温度通过影响薄膜的晶粒尺寸、生长取向和薄膜中载流子的浓度来改变Si基Bi关键词： sol-gel法 铁电薄膜 4Ti3O12')" href="#">Bi4Ti3O12 C-V特性}     

不同氮流量制备Mn3CuNx薄膜及其电、磁输运性质的研究

采用对靶磁控溅射方法在单晶Si(100)基片上制备了反钙钛矿结构的Mn₃CuN_x薄膜.通过控制制备过程中的反应气体氮气(N₂) 流量(N₂/Ar+N₂), 研究了氮含量对Mn₃CuN_x薄膜结构及物理性能的影响.分别利用X射线衍射仪、俄歇电子能谱、 原子力显微镜、X射线光电子能谱、物理性能测试系统和超导量子干涉仪, 对所制备薄膜的晶体结构、成分、表面形貌和电、磁输运性质进行了测试.结果表明:制备的薄膜均为反钙钛矿立方结构,且沿 (200) 晶面择优生长.随着氮含量的增大,薄膜表面粗糙度和颗粒度尺寸逐渐增大, 导致电阻率增加.氮含量对薄膜的电输运性质没有影响,所有薄膜电阻率均随着温度的降低逐渐增大, 呈现半导体型导电行为,这与对应的块体材料结果相反.Mn₃CuN_x薄膜随着测试温度的增大发生了 亚铁磁到顺磁的磁转变,且N含量的增大降低了磁有序转变温度,主要是由于N缺陷对Mn₆N八面体结构中 磁交换作用的影响所致.     

Catalytic performance of Mn3O4 and Co3O4 nanocrystals prepared by sonochemical method in epoxidation of styrene and cyclooctene

A simple sonochemical method was developed to synthesis uniform sphere-like Co₃O₄ and Mn₃O₄ nanocrystals. Epoxidation of styrene and cyclooctene by anhydrous tert-butyl hydroperoxide over the prepared Co₃O₄ and Mn₃O₄ nanocatalysts was investigated. The results of conversion activity were compared with bulk Co₃O₄ and Mn₃O₄. Under optimized reaction conditions, the nanocatalysts showed a superior catalytic performance as compared to the bulk catalysts. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and BET surface area, were used to characterize and investigate the nanocatalysts.     

Chemical synthesis of spinel nickel ferrite (NiFe2O4) nano-sheets

The present investigation is related to the deposition of single-phase nano-sheets spinel nickel ferrite (NiFe₂O₄) thin films onto glass substrates using a chemical method. Nano-sheets nickel ferrite films were deposited from an alkaline bath containing Ni²⁺ and Fe²⁺ ions. The films were characterized for their structural, surface morphological and electrical properties by means of X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and two-point probe electrical resistivity techniques. The X-ray diffraction pattern showed that NiFe₂O₄ nano-sheets are oriented along (3 1 1) plane. The FT-IR spectra of NiFe₂O₄ films showed strong absorption peaks around 600 and 400 cm⁻¹ which are typical for cubic spinel crystal structure. Microstructural study of NiFe₂O₄ film revealed nano-sheet like morphology with average sheet thickness of 30 nm. The room temperature electrical resistivity of the NiFe₂O₄ nano-sheets was 10⁷ Ω cm.     

Studies on electrodeposited As2S3 thin films by double exposure holographic interferometry technique

Arsenic trisulphide (As₂S₃) thin films have been deposited onto stainless steel and fluorine doped tin oxide (FTO) coated glass substrates by electrodeposition technique using arsenic trioxide (As₂O₃) and sodium thiosulphate (Na₂S₂O₃) as precursors and ethylene diamine tetracetic acid (EDTA) as a complexing agent. Double exposure holographic interferometry (DEHI) technique was used to determine the thickness and stress of As₂S₃ thin films. It was observed that the thickness of the thin film increases whereas film stress to the substrate decreases with an increase in the deposition time. X-ray diffraction and water contact angle measurements showed polycrystalline and hydrophilic surface respectively. The bandgap energy increases from 1.82 to 2.45 eV with decrease in the film thickness from 2.2148 to 0.9492 μm.     

Mn:BiFeO3/Zn:BiFeO3 bilayered thin films of (1 1 1) orientation

Ferroelectric and fatigue behavior of bilayered thin films consisting of Mn⁴⁺-modified BiFeO₃ and Zn²⁺-modified BiFeO₃, which were deposited on SrRuO₃-buffered Pt coated silicon substrates, were systematically investigated. The (1 1 1) orientation is induced for the BiFe_0.95Mn_0.05O₃/BiFe_0.95Zn_0.05O₃ bilayer, due to the introduction of the bottom BiFe_0.95Zn_0.05O₃ layer. With increasing the thickness ratio of the BiFe_0.95Mn_0.05O₃ layer, their leakage current decreases, and the fatigue endurance is greatly improved owing to the introduction of the BiFe_0.95Mn_0.05O₃ layer with a lower fatigue rate. The BiFe_0.95Mn_0.05O₃/BiFe_0.95Zn_0.05O₃ bilayer with the thickness ratio of 3:1 exhibits a larger remanent polarization of 2P_r ∼ 161.0 μC/cm² than those of bilayers with different thickness ratios, while their coercive field slightly increases with increasing the thickness ratio of the BiFe_0.95Mn_0.05O₃ layer.