Nanoscratch study of Zn1−xMnxO heteroepitaxial layers

We investigated the nanotribological properties of Zn_1−xMn_xO epilayers (0 ≤ x ≤ 0.16) grown by molecular beam epitaxy (MBE) on sapphire substrates. The surface roughness and friction coefficient (μ) were analyzed by means of atomic force microscopy (AFM) and hysitron triboscope nanoindenter techniques.The nanoscratch system gave the μ value of the films ranging from 0.17 to 0.07 and the penetration depth value ranging 294-200 nm when the Mn content was increased from x = 0 to 0.16. The results strongly indicate that the scratch wear depth under constant load shows that higher Mn content leads to Zn_1−xMn_xO epilayers with higher shear resistance, which enhances the Mn-O bond. These findings reveal that the role of Mn content on the growth of Zn_1−xMn_xO epilayers can be identified by their nanotribological behavior.     

Nanoscratch behavior of Zn1−xCdxSe heteroepitaxial layers

This paper describes the nanoscratch behavior of Zn_1−xCd_xSe epilayers grown using molecular beam epitaxy (MBE). Transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Hysitron Triboscope nanoindenter techniques were employed to determine the microstructures, morphologies, friction coefficients (μ), and hardnesses (H) of these materials, and thereby propose an explanation for their properties in terms of nanotribological behavior. Nanoscratch analysis revealed that the coefficient of friction of the Zn_1−xCd_xSe epilayer system decreased from 0.172 to 0.139 upon increasing the Cd content (x) from 0.07 to 0.34. Furthermore, studies of the scratch wear depth under a ramping load indicated that a higher Cd content provided the Zn_1−xCd_xSe epilayers with a higher shear resistance, which enhanced the strength of the CdSe bonds. These findings suggest that the greater stiffness of the CdSe bond, relative to that of the ZnSe bond, enhances the hardness of the epilayers. Indeed, the effect of the Cd content on the growth of the Zn_1−xCd_xSe epilayers is manifested in the resulting nanotribological behavior.     

Structural and photoluminescence analysis of Zn1 − xMnxO nanocrystalline powders

This Letter reports on structural and photoluminescence properties of Zn_1 − xMn_xO nanocrystalline powders, which were synthesized by using oxalate precursor decomposition method. From the XRD features, we have noticed that all samples exhibit wurtzite crystal structure. The origin of photoluminescence properties of Mn doped and undoped ZnO have been discussed.     

Room-temperature ferromagnetism in Zn1−xMnxO

In view of recent controversies on above room-temperature ferromagnetism (RTFM) in transition-metal-doped ZnO, the present paper aims to shed some light on the origin of ferromagnetism by investigating annealing effects on structure and magnetism for polycrystalline Zn_1−xMn_xO powder samples prepared by solid-state reaction method and annealed in air at different temperatures. Magnetic measurements indicate that the samples are ferromagnetic at room temperature (RTFM). Room temperature ferromagnetism has been observed in the sample annealed at a low temperature of 500 °C with a saturated magnetization (M_s) of 0.159 emu/g and a coercive force of 89 Oe. A reduction in RTFM is clearly observed in the sample annealed at 600 °C. Furthermore, the saturation magnetic moment decreases with an increase in grain size, suggesting that ferromagnetism is due to defects and/or oxygen vacancy confined to the surface of the grains. The experimental results indicate that the ferromagnetism observed in Zn_1−xMn_xO samples is intrinsic rather than associated with secondary phases.     

Optical properties of GaInNAsSb/GaAs/GaAs1−xNx (x ≈ 10%) saturable absorber quantum wells

We study the effect of the GaAsN narrow QWs on the optical properties of the GaInNAsSb/GaAs QWs using photoluminescence spectroscopy. A drastic effect of the N-rich layers on the QW photoluminesecnec (PL) intensity was observed with a strong influence of the spacer thickness. In the PL spectra a broad band caused by excitonic transitions related with N-related clusters in GaAs barriers is found. Based on calculations from experimental data, we have identified the low QW peak energy to the E₁-H₁ transition using the shear deformation potentials report Δp/p = 0.24.     

The structural, electronic and optical properties of CdxZn1 − xSe ternary alloys

The structural, electronic, and optical properties of Cd_xZn_1 − xSe alloys are investigated using the first-principles plane-wave pseudopotential method within the LDA approximations. In particular, the lattice constant, bulk modulus, electronic band structures, density of state, and optical properties such as dielectric functions, refractive index, extinction coefficient and energy loss function are calculated and discussed. Our results agree well with the available data in the literature.     

Photoluminescence investigation of ferromagnetic Ga1−xMnxN layers with GaN templates grown on sapphire (0 0 0 1) substrates

We have investigated the temperature and composition dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x ≈ 0.1-0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. The efficient PL is peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. The band-gap energy of the Ga_1−xMn_xN layers decreased with increasing temperature and manganese composition. The band-gap energy of the Ga_1−xMn_xN layers was modeled by the Varshni equation and the parameters were determined to be α = 2.3 × 10⁻⁴, 2.7 × 10⁻⁴, 3.4 × 10⁻⁴ eV/K and β = 210, 210, and 230 K for the manganese composition x = 0.1%, 0.2%, and 0.8%, respectively. As the Mn concentration in the Ga_1−xMn_xN layers increased, the temperature dependence of the band-gap energy was clearly reduced.     

Magnetic characterization of Bi(Fe1 − xMnx)O3

Bi(Fe_1 − xMn_x)O₃ ceramics (x up to 0.3) were prepared by rapid sintering. Weak ferromagnetism with two magnetic anomalies at low temperatures was observed for Bi(Fe_0.95Mn_0.05)O₃ and Bi(Fe_0.9Mn_0.1)O₃. From temperature-dependent magnetic relaxation measurements, the anomalies at 20 K and 100 K are related to the freezing of cluster spin glass.     

No room temperature ferromagnetism in Mn over-doped Zn1−xMnxO (x>0.02)

Mn-doped ZnO samples having composition Zn_1−xMn_xO (x=0.02, 0.04 and 0.05) were synthesized by solid state reaction technique with varying concentration of Mn from 0.02 to 0.05. Evidence of room temperature ferromagnetism was observed only in the composition Zn_0.98Mn_0.02O sintered at 500 °C. Our XRD pattern confirms the presence of Mn₃O₄ impurity phase in all the Zn_1−xMn_xO samples with the exception of Zn_0.98Mn_0.02O. We emphasize that the appearance of Mn₃O₄ phase in the system forbids the exchange type of interaction between the Mn ions and suppresses the ferromagnetism in all the Mn over-doped Zn_1−xMn_xO (x>0.02) system. SEM microstructure study also supports the interruption of exchange type of interaction inside the system with the increase in Mn concentration in the sample. Interestingly, for this particular composition, Zn_0.98Mn_0.02O sintered at 500 °C, glassy ferromagnetism type of transition is observed at low temperature. This type of transition is attributed to the formation of the oxides of Mn clusters at low temperature.     

Magnetism in Zn1−xMnxO crystal prepared by hydrothermal method

Crystal Zn_1−xMn_xO magnetic semiconductors have been obtained by using a hydrothermal method for the first time at temperature of 703 K with substituent fraction ranging from x=0 to 0.04. X-ray diffraction and optical absorption measurements provide evidence for the locating at Zn site of Mn ion in ZnO crystals. The non-monotonic variation of band gap indicates the short-ranged interactions of sp-d electrons. However, no evidence of ferromagnetism is found in these systems down to T=2 K. The magnetization is found to be contributed from both free spins and spins associated with antiferromagnetic clusters. The antiferromagnetism is confirmed by fitting a Curie-Weiss function.     

A Hall coefficient investigation of ferromagnetic Ga1−xMnxAs layers on (100) GaAs substrates

Ferromagnetic Ga_1−xMn_xAs epilayers with Mn mole fraction in the range of x≈2.2-4.4% were grown on semi-insulating (100) GaAs substrates using the molecular beam epitaxy technique. The transport properties of these epilayers were investigated through Hall effect measurements. The measured hole concentration of Ga_1−xMn_xAs layers varied from 4.4×10¹⁹ to 3.4×10¹⁹ cm⁻³ in the range of x≈2.2-4.4% at room temperature. From temperature dependent resisitivity data, the sample with x≈4.4% shows typical behavior for insulator Ga_1−xMn_xAs and the samples with x≈2.2 and 3.7% show typical behavior for metallic Ga_1−xMn_xAs. The Hall coefficient for the samples with x≈2.2 and 4.4% was fitted assuming a magnetic susceptibility given by Curie-Weiss law in a paramagnetic region. This model provides good fits to the measured data up to and the Curie temperature T_c was estimated to be 65, 83 K and hole concentration p was estimated to be 5.1×10¹⁹, 4.6×10¹⁹ cm⁻³ for the samples with x≈2.2 and 4.4%, respectively, confirming the existence of an anomalous Hall effect for metallic and insulating samples.     

A model for the band gap energy of the N-rich GaN1−xAsx (0<x≤0.07) and the As-rich GaN1−xAsx (0.95≤x≤1)

In this paper, a model for the band gap energy of the N-rich GaNAs (0<x≤0.07) and the As-rich GaNAs (0.95<x≤1) is developed. For the N-rich GaNAs, The parameters describing the variation of the CBM and the VBM in the N-rich GaNAs are obtained by fitting the experimental data. For the As-rich GaNAs, the parameters in the model are obtained by fitting the experimental data of the band gap energy. It is found that the band gap evolution of the N-rich energy is different from that of the As-rich band gap energy. The model may be used to calculate the band gap energy of other dilute group III-N–V nitrides.     

Growth dynamics of C-induced Ge dots on Si1−xGex strained layers

We address the growth mechanism of Ge quantum dots (QDs) on C-alloyed strained Si_1−xGe_x layers by in situ reflection high-energy electron-diffraction (RHEED). We show that C-induced growth on a Si-rich surface leads to a high density (about 10¹¹ cm⁻²) of small dome-shaped islands. On surfaces up to ≈65% richer in Ge we observe a decrease of the dot density by two orders of magnitude, which is associated to the increase of the adatom diffusion. Based on quantitative RHEED analysis, the islands are believed to grow in a Volmer-Weber mode even though their spotty electron transmission pattern is not detectable in the initial stages of growth due to the reduced size of the three-dimensional nucleation islands.     

Properties of optical phonons in Zn1−x−yMgyBexSe quaternary mixed crystal

Long wavelength optical lattice vibration and dielectric constants of the quaternary mixed crystal Zn_1−x−yMg_yBe_xSe are investigated based on the pseudo-unit-cell mode and Born-Huang procedure. It is found that this material shows a three-mode behavior and the oscillator strength of each mode is mainly controlled by only one component. The theoretical results also show that the linear interpretation method for dielectric constants is reliable. The vibrational frequencies and the oscillator strengths of the ternary mixed crystals Be_xZn_1−xSe, Be_xMg_1−xSe and Mg_xZn_1−xSe are also calculated as special cases of the quaternary mixed crystal for comparing with experiments. The calculation shows agreement with the experimental results.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

Nanoscale semiconductor Pb1−xSnxSe (x = 0.2) thin films synthesized by electrochemical atomic layer deposition

In this paper the fabrication and characterization of IV-VI semiconductor Pb_1−xSn_xSe (x = 0.2) thin films on gold substrate by electrochemical atomic layer deposition (EC-ALD) method at room temperature are reported. Cyclic voltammetry (CV) is used to determine approximate deposition potentials for each element. The amperometric I-t technique is used to fabricate the semiconductor alloy. The elements are deposited in the following sequence: (Se/Pb/Se/Pb/Se/Pb/Se/Pb/Se/Sn …), each period is formed using four ALD cycles of PbSe followed by one cycle of SnSe. Then the deposition manner above is cyclic repeated till a satisfactory film with expected thickness of Pb_1−xSn_xSe is obtained. The morphology of the deposit is observed by field emission scanning electron microscopy (FE-SEM). X-ray diffraction (XRD) pattern is used to study its crystalline structure; X-ray photoelectron spectroscopy (XPS) of the deposit indicates an approximate ratio 1.0:0.8:0.2 of Se, Pb and Sn, as the expected stoichiometry for the deposit. Open-circuit potential (OCP) studies indicate a good p-type property, and the good optical activity makes it suitable for fabricating a photoelectric switch.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.     

Structural studies of evaporated CoxCr1−x/Si (1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si (1 0 0) and glass substrates. Chemical composition and interface properties have been studied by modelling Rutherford backscattering spectra (RBS) using SIMNRA programme. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Simulation of the energy spectra shows an interdiffusion profile in the thickest films, but no diffusion is seen in thinner ones. Microscopic characterizations of the films are done with X-ray diffraction (XRD) measurements. All the samples are polycrystalline, with an hcp structure and show a 〈0 0 0 1〉 preferred orientation. Atomic force microscopies (AFM) reveal very smooth film surfaces.     

Effect of microstructure on the nanomechanical properties of Zn1−xCdxSe alloys

We present a study of the nanoindentation behavior of Zn_1−xCd_xSe epilayers grown using molecular beam epitaxy; the surface roughness, microstructure, and crystallinity were analyzed using atomic force microscopy, cross-sectional transmission electron microscopy, and X-ray diffraction; the hardness H and elastic modulus E were studied using nanoindentation techniques. We found that these highly crystalline materials possessed no stacking faults or twins in their microstructures. We observed a very marked increase in the value of H and a significant decrease in the value of E upon increasing the concentration of Cd, presumably because of an increase in the stiffness of the CdSe bond relative to that of the ZnSe bond. We observed a corresponding shrinkage of the contact-induced damage area for those films having a small grain size and a higher value of H. It appears that resistance against contact-induced damage requires a higher Cd concentration.