Photoluminescence of ZnO nanowires dependent on O2 and Ar annealing

High-purity ZnO nanowires have been synthesized on Si substrates without the presence of a catalyst at 600 °C by a simple thermal vapor technique. Photoluminescence (PL) spectra of the annealed samples at 900 °C under oxygen and argon gases have been investigated. After O₂ or Ar annealing, the PL visible-emission intensity that is related to intrinsic defects (oxygen vacancies) is greatly reduced compared with as-grown ZnO nanowires because the oxygen-gas ions or oxygen interstitials diffuse into the oxygen vacancies during annealing process. The blue-band peak of the O₂- or Ar-annealed ZnO naonowires is also smaller than the green-band peak in the visible broadband because of the reduction of oxygen vacancies. Therefore, the main intrinsic defects (oxygen vacancies) of as-grown ZnO nanowires can be reduced by O₂ or Ar annealing, which is an important procedure for the development of advanced optoelectronic ZnO nanowire devices.     

Effects of sic buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates

ZnO films have been grown by a sol-gel process on Si (1 1 1) substrates with and without SiC buffer layers. The influence of SiC buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates was investigated. The intensity of the E₂ (high) phonon peak in the micro-Raman spectrum of ZnO film with the SiC buffer layer is stronger than that of the sample without the SiC buffer layer, and the breadth of E₂ (high) phonon peak of ZnO film with the SiC buffer layer is narrower than that of the sample without the SiC buffer layer. These results indicated that the crystalline quality of the sample with the SiC buffer layer is better than that of the sample without the SiC buffer layer. In photoluminescence spectra, the intensity of free exciton emission from ZnO films with the SiC buffer was much stronger than that from ZnO film without the SiC buffer layer, while the intensity of deep level emission from sample with the SiC buffer layer was about half of that of sample without the SiC buffer layer. The results indicate the SiC buffer layer improves optical qualities of ZnO films on Si (1 1 1) substrates.     

Auger electron spectroscopy of Au/NiOx contacts on p-GaN annealed in N2 and O2 + N2 ambients

We have designed a promising contact scheme to p-GaN. Au/NiO_x layers with a low concentration of O in NiO_x are deposited on p-GaN by reactive dc magnetron sputtering and annealed in N₂ and in a mixture of O₂ + N₂ to produce low resistivity ohmic contacts. Annealing has been studied of NiO_x layers with various contents of oxygen upon the electrical properties of Au/NiO_x/p-GaN. It has been found that the Au/NiO_x/p-GaN structure with a low content of oxygen in NiO_x layer provides a low resistivity ohmic contact even after subsequent annealing in N₂ or O₂ + N₂ ambient at 500 °C for 2 min.Auger depth profiles and transmission electron microscopy (TEM) micrographs reveal that while annealing in O₂ + N₂ ambient results in reconstruction of the initial deposited Au/NiO_x/p-GaN contact structure into a Au/p-NiO/p-GaN structure, annealing in N₂ brings about reconstruction into Au/p-NiO/p-GaN and Ni/p-NiO/p-GaN structures. Hence, in both cases, after annealing in N₂ as well as in O₂ + N₂ ambient, the ohmic properties of the contacts are determined by creation of a thin oxide layer (p-NiO) on the metal/p-GaN interface. Higher contact resistivities in the samples annealed in O₂ + N₂ ambient are most likely caused by a smaller effective area of the contact due to creation of voids.     

Characterization of N-doped ZnO layers grown on (0 0 0 1) GaN/Al2O3 substrates by molecular beam epitaxy

We investigated the optical properties and electrical properties of N-doped ZnO layers grown on (0 0 0 1) GaN/Al₂O₃ substrates by molecular beam epitaxy, employing 10 K photoluminescence (PL) measurements, current–voltage (IV) measurements, capacitance–voltage (CV) measurements, and 100 K photocapacitance (PHCAP) measurements. 10 K PL spectra showed that excitonic emission is dominant in N-doped ZnO layers grown after O-plasma exposure, while overall PL emission intensity is significantly reduced and deep level emission at around 2.0 2.2 eV is dominant in N-doped ZnO layers grown after Zn exposure. IV and CV measurements showed that N-doped ZnO layers grown after Zn exposure have better Schottky diode characteristics than O-plasma exposed samples, and an N-doped ZnO layer grown at 300 °C after Zn exposure has best Schottky diode characteristics. This phenomenon is presumably due to lowered background electron concentration induced by the incorporation of N. PHCAP measurements for the N-doped ZnO layer revealed several midgap trap centers at 1.2 1.8 eV below conduction band minimum.     

Epitaxial ZnO films grown on ZnO-buffered c-plane sapphire substrates by hydrothermal method

ZnO films are hydrothermally grown on ZnO-buffered c-plane sapphire substrates at a low temperature of 70 °C. A radio-frequency (RF) reactive magnetron sputtering has been used to grow the ZnO buffer layers. X-ray diffraction, scanning electron microscopy, and room temperature photoluminescence are carried out to characterize the structure, morphology and optical property of the films. It is found that the films are stress-free. The epitaxial relationship between the ZnO film and the c-plane sapphire substrate is found to be ZnO (0 0 0 1)||Al₂O₃ (0 0 0 1) in the surface normal and in plane. Sapphire treatment, as such acid etching, nitridation, and oxidation are found to influence the nucleation of the film growth, and the buffer layers determine the crystalline quality of the ZnO films. The maximum PL quantum efficiency of ZnO films grown with hydrothermal method is found to be about 80% of single-crystal ZnO.     

The high quality ZnO growth on c-Al2O3 substrate with Cr2O3 buffer layer using plasma-assisted molecular beam epitaxy

High quality epitaxial ZnO films were grown on c-Al₂O₃ substrates with Cr₂O₃ buffer layer by plasma-assisted molecular beam epitaxy (P-MBE). The hexagonal crystalline Cr₂O₃ layer was formed by oxidation of the Cr-metal layer deposited on the c-Al₂O₃ substrate using oxygen plasma. The epitaxial relationship was determined to be ZnO//Cr₂O₃//Cr//Al₂O₃ and ZnO//Cr₂O₃//[0 0 1]Cr//Al₂O_3. The Cr₂O₃ buffer layer was very effective in improving the surface morphology and crystal quality of the ZnO films. The photoluminescence spectrum showed the strong near band-edge emissions with the weak deep-level emission, which implies high optical quality of the ZnO films grown on the Cr₂O₃ buffer.     

Formation of aligned silicon-nanowire on silicon in aqueous HF/(AgNO3 + Na2S2O8) solution

Highly oriented silicon nanowire (SiNW) layer was fabricated by etching Si substrate in HF/(AgNO₃ + Na₂S₂O₈) solution at 50 °C. The morphology and the photoluminescence (PL) of the etched layer as a function of Na₂S₂O₈ concentration were studied. The SiNW layers formed on silicon were investigated by scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX). It was demonstrated that the morphology of the etched layers depends on the Na₂S₂O₈ concentration. Room-temperature photoluminescence (PL) from etched layer was observed. It was found that the utilisation of Na₂S₂O₈ decreases PL peak intensity. Finally, a discussion on the formation process of the silicon nanowires is presented.     

The role of a ZnO buffer layer in the growth of ZnO thin film on Al2O3 substrate

A ZnO buffer layer and ZnO thin film have been deposited by the pulsed laser deposition technique at the temperatures of 200 C and 400 C, respectively. Structural, electrical and optical properties of ZnO thin films grown on sapphire (Al₂O₃) substrate with 1, 5, and 9 nm thick ZnO buffer layers were investigated. A minute shift of the (101) peak was observed which indicates that the lattice parameter was changed by varying the thickness of the buffer layer. High resolution transmission electron microscopy (TEM) was used to investigate the thickness of the ZnO buffer layer and the interface involving a thin ZnO buffer between the film and substrate. Selected area electron diffraction (SAED) patterns show high quality hexagonal ZnO thin film with 30 in-plane rotation with respect to the sapphire substrate. The use of the buffer can reduce the lattice mismatch between the ZnO thin film and sapphire substrate; therefore, the lattice constant of ZnO thin film grown on sapphire substrate became similar to that of bulk ZnO with increasing thickness of the buffer layer.     

Reaction of O2 with the boron-terminated TaB2(0 0 0 1) surface

X-ray photoelectron spectroscopy has been used to study the clean TaB₂(0 0 0 1) surface and its reaction with O₂. In agreement with previous studies, XPS indicates that the clean surface is boron terminated. The topmost boron layer shows a chemically shifted B 1s peak at 187.1 eV compared to a B 1s peak at 188.6 eV for boron layers below the surface. The 187.1-188.6 eV peak intensity ratio and its variation with angle between the crystal normal and the detector is well described by a simple theoretical model based on an independently calculated electron inelastic mean free path of 15.7 Å for TaB₂. The dissociative sticking probability of O₂ on the boron-terminated TaB₂(0 0 0 1) surface is lower by a factor of 10⁴ than for the metal-terminated HfB₂(0 0 0 1) surface.     

High-temperature measurements of the rates of the reactions CH2O + Ar → Products and CH2O + O2 → Products

The two-channel thermal decomposition of formaldehyde [CH₂O], (1a) CH₂O + Ar → HCO + H + Ar, and (1b) CH₂O + Ar → H₂ + CO + Ar, was studied in shock tube experiments in the 2258-2687 K temperature range, at an average total pressure of 1.6 atm. OH radicals, generated on shock heating trioxane-O₂-Ar mixtures, were monitored behind the reflected shock front using narrow-linewidth laser absorption. 1,3,5 trioxane [C₃H₆O₃] was used as the CH₂O precursor in the current experiments. H-atoms formed upon CH₂O and HCO decomposition rapidly react with O₂ to produce OH via H + O₂ → O + OH. The recorded OH time-histories show dominant sensitivity to the formaldehyde decomposition pathways. The second-order reaction rate coefficients were inferred by matching measured and modeled OH profiles behind the reflected shock. Two-parameter fits for k_1a and k_1b, applicable in this temperature range, are:

     

The influence of H2/(H2 + Ar) ratio on microstructure and optoelectronic properties of microcrystalline silicon films deposited by plasma-enhanced CVD

Hydrogenated microcrystalline silicon films were deposited by glow discharge decomposition of SiH₄ diluted in mixed gas of Ar and H₂. By investigating the dependence of the film crystallinity on the flow rates of Ar and H₂, we showed that the addition of Ar in diluted gas markedly improves the crystallinity due to an enhanced dissociation of SiH₄. The infrared-absorption spectrum reveals that the fraction of SiH bonding increases with increasing the rate ratio of H₂/(H₂ + Ar). The surface roughness of the films increases with increasing the flow rate ratio of H₂/(H₂ + Ar), which is attributed to the decrease of massive bombardment of Ar ions in the plasma. Refractive index and absorption coefficient of the films were obtained by simulating the optical transmission spectra using a modified envelope method. Electrical measurements of the films show that the dark conductivity increases and the activation energy decreases with the ratio of H₂/(H₂ + Ar). A reasonable explanation is presented for the dependence of the microstructure and optoelectronic properties on the flow rate ratio of H₂/(H₂ + Ar).     

Determination of the rate of H + O2 + M → HO2 + M (M = N2, Ar, H2O) from ignition of syngas at practical conditions

In H₂ and H₂/CO oxidation, the H + O₂ + M termination step is one of the most important reactions at elevated pressures. With the recent, increased interest in synthetic fuels, an accurate assessment of its rate coefficient becomes increasingly important, especially for real fuel/air mixtures. Ignition delay times in shock-tube experiments at the conditions selected in this study are only sensitive to the rates of the title reaction and the branching reaction H + O₂ = OH + O, the rate of which is known to a high level of accuracy. The rate coefficient of the title reaction for M = N₂, Ar, and H₂O was determined by adjusting its value in a detailed chemical kinetics model to match ignition delay times for H₂/CO/O₂/N₂, H₂/CO/O₂/Ar, and H₂/CO/O₂/N₂/H₂O mixtures with fuel/air equivalence ratios of ? = 0.5, 0.9, and 1.0. The rate of H + O₂ + N₂ = HO₂ + N₂ was measured to be 2.7 (−0.7/+0.8) × 10¹⁵ cm⁶/mol² s for T = 916-1265 K and P = 1-17 atm. The present determination agrees well with the recent study of Bates et al. [R.W. Bates, D.M. Golden, R.K. Hanson, C.T. Bowman, Phys. Chem. Chem. Phys. 3 (2001) 2337-2342], whose rate expressions are suggested herein for modeling the falloff regime. The rate of H + O₂ + Ar = HO₂ + Ar was measured to be 1.9 × 10¹⁵ cm⁶/mol² s for T = 932-965 K and P = 1.4 atm. The rate of H + O₂ + H₂O = HO₂ + H₂O was measured to be 3.3 × 10¹⁶ cm⁶/mol² s for T = 1071-1161 K and P = 1.3 atm. These are the first experimental measurements of the rates of the title reactions in practical combustion fuel/air mixtures.     

Formation and characterization of the Cu2O overlayer on Zn-terminated ZnO(0 0 0 1)

Low-energy electron diffraction, X-ray photoelectron spectroscopy and synchrotron-radiation-excited angle-resolved photoelectron spectroscopy have been used to characterize Cu-oxide overlayers on the Zn-terminated ZnO(0 0 0 1) surface. Deposition of Cu on the ZnO(0 0 0 1)-Zn surface results in the formation of Cu clusters with (1 1 1) top terraces. Oxidation of these clusters by annealing at 650 K in O₂ atmosphere (1.3 × 10⁻⁴ Pa) leads to an ordered Cu₂O overlayer with (1 1 1) orientation. Good crystallinity of the Cu₂O(1 1 1) overlayer is proved by energy dispersion of one of Cu₂O valence bands. The Cu₂O(1 1 1) film exhibits a strong p-type semiconducting nature with the valence band maximum (VBM) of 0.1 eV below the Fermi level. The VBM of ZnO at the Cu₂O(1 1 1)/ZnO(0 0 0 1)-Zn interface is estimated to be 2.4 eV, yielding the valence-band offset of 2.3 eV.     

Effect of a LaSrCoO3 buffer layer on Pb1 − xLaxTi1 − x/4O3 films studied by polarized Raman spectroscopy

A confocal Raman investigation of Pb_1 − xLa_xTi_1 − x/4O₃ (PLT) thin films grown by RF magnetron sputtering on PbO_x/Pt/Ti/SiO₂/Si substrates with an intermediate LaSrCoO₃ (LSCO) layer was performed. The influence of the LaSrCoO₃ buffer layer was analyzed taking advantage of the observed Raman spectral band variation, which varied according to different manufacturing procedures. In the presence of a LSCO layer, the A1(1TO) Raman mode, which was indicative of tetragonal distortion, was pronouncedly enhanced, and a slight deviation from the (0 0 1) plane of the film was observed from the angular dependence of the polarized Raman spectral intensity. Furthermore, the spectral band variation as well as the residual stress along the in-depth direction was measured in the film from cross-sectional spectral line scans. This latter measurement showed a relaxation of the lattice mismatch in the presence of LSCO and PbO layers.     

Clusterization of vacancy defects in ZnO irradiated with 2 MeV O

Slow positrons have been used to study ZnO layers grown on a-axis sapphire and irradiated by 2 MeV O⁺ ions to fluences from 10¹² cm⁻² to 10¹⁷ cm⁻². At low fluences Zn vacancies are observed, and their introduction rate is estimated as 2000 cm⁻¹. At the highest fluences of 10¹⁶-10¹⁷ cm⁻² vacancy clusters are formed. The extent of the primary damage and its recovery is discussed.     

Structural characterization of Ga-doped Mg0.1Zn0.9O layers grown on ZnO/α-Al2O3 templates by P-MBE

In this study, structural properties of epitaxial Ga-doped Mg_0.1Zn_0.9O layers grown on ZnO/α-Al₂O₃ templates by plasma-assisted molecular beam epitaxy have been investigated by high-resolution transmission electron microscopy (HRTEM), and high resolution X-ray diffraction (HRXRD). From analysis of the diffraction pattern, the monocrystallinity of the Mg_0.1Zn_0.9O layer with hexagonal structure is confirmed. The orientation relationship between Mg_0.1Zn_0.9O and the template is determined as (0 0 0 1)_Mg0.1Zn0.9O(0 0 0 1)_ZnO(0 0 0 1)_Al2O3 and [ [ ]_ZnO[ . The density of dislocations near the top surface layers measured by plan-view TEM is about 3.610¹⁰ cm⁻², one order of magnitude higher than the value obtained for ZnO layers on α-Al₂O₃ with a MgO buffer. Cross-sectional observation revealed that the majority of threading dislocations are in the [0 0 0 1] line direction, i.e. they lie along the surface normal and consist of edge, screw, and mixed dislocations. Cross- sectional TEM and X-ray rocking curve experiments reveal that most of dislocations are edge dislocations. The interface of Mg_0.1Zn_0.9O and ZnO layers and the effect of excess Ga-doping in these layers have been also studied.     

Magnetoresistance of magnetite thin films grown by pulsed laser deposition on GaAs(1 0 0) and Al2O3(0 0 0 1)

Magnetotransport properties of magnetite thin films deposited on gallium arsenide and sapphire substrates at growth temperatures between 473 and 673 K are presented. The films were grown by UV pulsed laser ablation in reactive atmospheres of O₂ and Ar, at working pressure of 8 × 10⁻² Pa. Film stoichiometry was determined in the range from Fe_2.95O₄ to Fe_2.97O₄. Randomly oriented polycrystalline thin films were grown on GaAs(1 0 0) while for the Al₂O₃(0 0 0 1) substrates the films developed a (1 1 1) preferred orientation. Interfacial Fe³⁺ diffusion was found for both substrates affecting the magnetic behaviour. The temperature dependence of the resistance and magnetoresistance of the films were measured for fields up to 6 T. Negative magnetoresistance values of ∼5% at room temperature and ∼10% at 90 K were obtained for the as-deposited magnetite films either on GaAs(1 0 0) or Al₂O₃(0 0 0 1).     

Effect of surface roughness on the development of protective Al2O3 on Fe-10Al (at.%) alloys containing 0-10 at.% Cr

The effect of alloy surface roughness, achieved by different degrees of surface polishing, on the development of protective alumina layer on Fe-10 at.% Al alloys containing 0, 5, and 10 at.% Cr was investigated during oxidation at 1000 °C in 0.1 MPa oxygen. For alloys that are not strong Al₂O₃ formers (Fe-10Al and Fe-5Cr-10Al), the rougher surfaces increased Fe incorporation into the overall surface layer. On the Fe-10Al, more iron oxides were formed in a uniform layer of mixed aluminum- and iron-oxides since the layer was thicker. On the Fe-5Cr-10Al, more iron-rich nodules developed on an otherwise thin Al₂O₃ surface layer. These nodules nucleated preferentially along surface scratch marks but not on alloy grain boundaries. For the strong Al₂O₃-forming Fe-10Cr-10Al alloy, protective alumina surface layers were observed regardless of the surface roughness. These results indicate that the formation of a protective Al₂O₃ layer on Fe-Cr-Al surfaces is not dictated by Al diffusion to the surface. More cold-worked surfaces caused an enhanced Fe diffusion, hence produced more Fe-rich oxides during the early stage of oxidation.     

The structure and optical characters of the ZnO film grown on GaAs/Al2O3 substrate

In this paper ZnO films are grown on GaAs/Al₂O₃ substrates at different temperature by metal-organic chemical vapor deposition (MOCVD). The GaAs/Al₂O₃ substrates are formed by depositing GaAs layer (∼35 nm) on the Al₂O₃ substrate. The results of X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) demonstrate that most of the Ga and As atoms form Ga-As bond and the GaAs layer does not present any orientation. The characters of the ZnO films grown on GaAs/Al₂O₃ substrates are investigated by XRD, photoluminescence (PL), atomic force microscopy (AFM) and Raman scattering. Compared with ZnO film grown on Al₂O₃ substrate, ZnO film prepared by our fabrication scheme has good crystal and optical quality. Meanwhile its grain size becomes bigger according to the AFM image. Raman analysis indicates that the intrinsic defects and the in-plane tensile stress are obviously reduced in ZnO/GaAs/Al₂O₃ samples.     

Fabrication of the hydrogen resistive ferroelectric film of the (Pb0.72La0.28)Ti0.93O3/Pb(Zr0.52Ti0.48)O3/(Pb0.72La0.28)Ti0.93O3 heterostructure by a pulsed laser deposition method

(Pb_0.72La_0.28)Ti_0.93O₃ (PLT)/Pb(Zr_0.52Ti_0.48)O₃ (PZT)/PLT heterostructure was fabricated by using a pulsed laser deposition method. After depositing this structure, the hydrogen annealing process was performed in the forming gas (95% N₂ + 5% H₂) at a substrate temperature of 400 °C for 30 min to study the effects of hydrogen passivation.The heterostructure was not degraded by the hydrogen annealing in contrast with the case of PZT film without buffer layers. This heterostructure showed almost no degradation in terms of the remanent polarization even after the H₂ annealing, while the PZT film exhibited 64% reduction, which is from 20.1 to 7.3 μC/cm² after the annealing. The leakage current was decreased by an order in the case of the heterostructure, while the leakage current of the PZT film increased by an order.These can be explained that the PLT bottom buffer layer works as a seeing layer to help the PZT growth and the top PLT buffer layer acts as a barrier for penetrating hydrogen atoms.