Modeling of fast phase transitions dynamics in metal target irradiated by pico- and femtosecond pulsed laser

We investigate laser pulse influence on aluminum target in irradiance range 10⁹ to 10¹⁶ W/cm², pulse duration between 10⁻⁸ and 10⁻¹⁵ s, Gaussian time profile with wavelength of 0.8 μm. For all computations energy density was 10 J/cm². Plasma in the evaporated material is generated at the energy density above 10 J/cm²as the modeling showed.Long and short laser pulses distinguish by the mechanisms of energy transformation. For short laser pulses there is volumetric energy absorption, together with rapid phase transitions it lead to overheating in solid and liquid states, overheated solid temperature rises up to (6-8)T_m. Under influence of the energy saved in overheated solid, duration of the phase transitions becomes nanosecond, which is several orders of magnitude longer than laser pulse.     

Tunable terahertz generation from one CO2 laser in a GaSe crystal

Coherent terahertz pulses have been generated at a range of 236.3-1104.5 μm (0.27-1.3 THz) by one CO₂ laser with dual-wavelength output based on collinearly phase-matched different frequency generation (DFG) in a GaSe crystal. This source has the advantages of compact and simplicity for tuning. The output power of the THz pulse and phase-matching conditions were investigated. The maximum single pulse energy of 11 nJ was generated at a frequency of 1.23 THz (243.6 μm), corresponding to a peak output power 182 mW.     

Removal of graffiti from the mortar by using Q-switched Nd:YAG laser

This paper presents part of the larger study on microstructural features of mortars and it's effects on laser cleaning process. It focuses on the influence of surface roughness, porosity and moisture content of mortars on the removal of graffiti by Nd:YAG laser. The properties of this laser are as follows: wavelength (λ) 1.06 μm, energy: 500 mJ per pulse, pulse duration: 10 ns. The investigation shows that the variation of laser fluence with the number of pulses required for the laser cleaning can be divided into two zones, namely effective zone and ineffective zone. There is a linear relationship observed between number of pulses required for laser cleaning and the laser fluence in the effective zone, while the number of pulses required for the laser cleaning is almost constant even though the laser fluence increases in the ineffective zone. Moreover, surface roughness, porosity and moisture content of mortar samples have influence on the laser cleaning process. The effect of these parameters become however negligible at the high level of laser fluence. The number of pulses required for the laser cleaning is low for smooth surface or less porous mortar. Furthermore, the wetness of the samples facilitates the cleaning process.     

Graphene-based passively Q-switched 2 μm thulium-doped fiber laser

We demonstrated stable pulses generation at 2 μm in a passively Q-switched thulium-doped fiber laser using a few layer graphene thin film. The maximum output power was 4.5 mW and the single pulse energy was 85 nJ at 53 kHz repetition rate, and the pulse width was about 1.4 μs. The pulse width and the repetition rate of the Q-switched fiber laser can be changed along with the pump power. To the best of our knowledge, this is the first report of graphene saturable absorber for passively Q-switched 2 μm fiber lasers.     

Passively Q-switched and mode-locked diode-pumped Nd:YVO4 laser with LT-GaAs output coupler

We have demonstrated an efficient and compact passively Q-switched and mode-locked (QML) 1064 nm Nd:YVO₄ laser by using a low temperature grown GaAs (LT-GaAs) saturable absorber as well as an output coupler. Stable QML with envelope duration as short as 10 ns and Q-switched repetition rate of 36 kHz was obtained. It is the shortest envelope duration as far as we know, and it is so short that it can be used as Q-switching pulses directly. At 6.9 W of the incident pump power, average output power of 1.24 W was achieved and the corresponding peak power and energy of a single Q-switched pulse were 3.44 kW and 34.4 μJ, respectively. The mode-locked pulses inside the Q-switched pulse envelope had a repetition rate of 780 MHz.     

Specialty Yb fiber amplifier for microchip Nd laser: Towards ∼1-mJ/1-ns output at kHz-range repetition rate

We demonstrate and optimize, for a mJ/ns release at the wavelength 1.064 μm, the operation of a compact laser system designed in the form of a hybrid, active-passive, Q-switched Nd³⁺:YAG/Cr⁴⁺:YAG microchip laser seeding an Yb-doped specialty multi-port fiber amplifier. As the result of the amplifier optimization, ∼1 mJ, ∼1 ns, almost single-mode pulses at a 1-10-kHz repetition rate are achieved, given by a gain factor of ∼19 dB for an 11-μJ input from the microchip laser. Meanwhile, a lower pulse energy, ∼120 μJ, but a much higher gain (∼25 dB) are eligible for the less powerful (0.35 μJ) input pulses.     

Circular and rectangular via holes formed in SiC via using ArF based UV excimer laser

Circular via holes with diameters of 10, 25, 50 and 70 μm and rectangular via holes with dimensions of 10 μm × 100 μm, 20 μm × 100 μm and 30 μm × 100 μm and drilled depths between 105 and 110 μm were formed in 300 μm thick bulk 4H-SiC substrates by Ar/F₂ based UV laser drilling (λ = 193 nm) with a pulse width of ∼30 ns and a pulse frequency of 100 Hz. The drilling rate was linearly proportional to the fluence of the laser, however, the rate decreased for the larger via holes. The laser drilling produces much higher etch rates (229-870 μm/min) than conventional dry etching (0.2-1.3 μm/min) and the via entry can be tapered to facilitate subsequent metallization.     

The generation of high pulse and average power radiation in eye-safe spectral region by the third stokes generation in barium nitrate Raman laser

The generation of high pulse and average power radiation in the eye-safe region (wavelength around 1.599 μm) by the third Stokes generation in a barium nitrate Raman laser was demonstrated by pumping with 10 ns pulses of a Nd:YAG laser. Converted pulse energy was up to 93 mJ (peak power was 10 MW) at a pump energy of 300 mJ, which corresponds to a quantum efficiency of 47%. The average output power of the third Stokes radiation was 1.8 W.     

Characteristics of a flowing He-SrCl2 vapor laser

An experimental investigation on the characteristics of a flowing He-SrCl₂ vapor laser is carried out. The output power as a function of the SrCl₂ vapor pressure is presented by calculating the radial temperature distribution of the discharge tube. The temporal dependences of the discharge current pulse on the laser pulses at 1 μm, ∼ 3 μm and 6.45 μm lines in strontium atom and ion, as well as the spot modes of the laser beam are measured and analyzed under different laser output power.     

Efficient second-harmonic generation of ultrashort pulses with simultaneous quasi-phase matching and group velocity matching in periodic 90° domain structures of potassium niobate

Triple-line-shaped electrodes were devised to fabricate a periodically poled 90° domain structure of KNbO₃ (PP90KN) of 20.25 μm period with uniform periodicity and reproducibility. Using the fundamental pulse of 141 fs duration at 1619 nm wavelength, an efficient broadband type-I quasi-phase-matched second-harmonic generation was realized in an 8.3 mm long PP90KN by satisfying both phase matching and group-velocity-matching in the telecommunication L-band at room temperature. Second-harmonic pulses showed no significant temporal and spectral distortion and had a pulse duration of about 144 fs, which agreed well with the theoretical value of 142 fs. The conversion efficiency of the second-harmonic generation was 28.7% at the fundamental pulse energy of 0.92 nJ, which is about 60% of the theoretical value.     

Effect of plasma confinement on laser shock microforming of thin metal sheets

Laser shock forming is conceived as a non-thermal laser forming method of thin metal sheets using the shock wave induced by laser irradiation to modify the target curvature. The plastic deformation induced by the shock wave and the direct plasma pressure applied on the material generate a residual stress distribution in the material finally leading to its bending. Using water as a confinement medium for the plasma the pressure can be increased around 10 times and the final deformation has a dramatic increase.The effect can be made clearly apparent in thin specimens (up to 1 mm). In the present study thin (100 μm) stainless steel (AISI 316) strips (1 mm long and 300 μm wide) in single and double pinned configurations have been investigated.A Nd:YAG Laser (1064 nm) with 10 ns of pulse length (FWHM) and an energy of 21 mJ per pulse is focused in the strip (spot diameter of the spot = 500 μm).Experimental and numerical studies of the influence of plasma confinement in the process and number of applied pulses are presented.The study shows that the final bending of the specimens can be controlled on a relative wide range by a stable quasi-proportional relation to the number of applied pulses and, what is considered as of major importance, that plasma confinement increases the generated pressure and thus the bending in the target.Laser shock microforming in confined configuration is considered as a technique allowing the successful processing of components in a medium range of miniaturization.     

Three-level operation of a diode-bar-pumped Yb:S-FAP laser

We present an all solid-state Yb:S-FAP laser system running on the three-level laser transition at 985 nm. The pump source was a high fill-factor laser diode bar, with the output reformatted using a two-mirror beamshaping system to produce a rectangular pump beam that focused to a square spot. A nearly on-axis multipassing system was used to obtain four pump passes through a 1.6 mm Yb:S-FAP laser crystal. Gain-switched three-level laser output was achieved with an efficiency of 4.3% with respect to incident pump power. Electro-optic Q-switching produced 0.12 mJ pulses for a pump pulse energy of 11 mJ. Intra-cavity second-harmonic generation yielded a maximum pulse energy at 492.5 nm of 12 μJ.     

1.3414 μm Nd:YAP pulse laser in Q-switched mode

In this paper, a flash-lamp pumped 1.3414 μm Nd:YAP Q-switched pulse laser are presented. The experimental results for about 45 ns of pulse duration and more than 300 mJ of output energy have been obtained and discussed.     

Diode-pumped passively Q-switched mode-locked Nd:YLF laser with uncoated GaAs saturable absorber

We have demonstrated passively Q-switched mode-locked all-solid-state Nd:YLF laser with an uncoated GaAs wafer as saturable absorber and output mirror simultaneously. Q-switched mode-locking pulses laser with about 100% modulation depth were obtained. The average output power is 890 mW at the incident pump power of 5.76 W, corresponding to an optical slop efficiency of 20%. The temporal duration of mode-locked pulses was about 21 ps. At the Q-switched repetition rate of 30 kHz, the energy and peak power of a single pulse near the maximum of the Q-switched envelope was estimated to be about 1.6 μJ and 76 kW.     

Laser fabricated microchannels inside photostructurable glass-ceramic

Microchannels have been fabricated by laser direct-write in photostructurable glass-ceramic (Foturan) for their application in 3D-microfluidic systems. A Nd:YAG laser delivering 10 ns pulses at 355 nm wavelength has been used for irradiation. Afterwards, thermal treatment and chemical etching have been required for channel formation. The kinetics of channel formation and the channel morphology have been studied by optical and electron microscopy. A minimum accumulated energy (pulse energy multiplied by the number of pulses in a same site) is required to induce channel formation. Channels with symmetric round apertures at both ends can be obtained when using low pulse energies. On the contrary, irradiation with too high energetic pulses produces direct material damage in Foturan and provokes the formation of non-symmetric channels. One millimetre long channels with a minimum radius of 15 μm can be opened through Foturan slides after 15 min of chemical etching.     

Efficient lasing action from Rhodamine-110 (Rh-110) impregnated sol-gel silica samples prepared by dip method

Rhodamine-110/sol-gel samples are prepared by sol-gel technique using dip method. Concentration dependent photophysical studies of these samples have indicated about the least possibility of aggregate formation. The lasing action of Rh-110 in silica samples is studied as a function of dye concentration. An efficient laser emission is observed when the samples are transversely pumped at 337.1 nm and 1.5 Hz repetition rate using a nitrogen laser (400 μJ energy/pulse and 4 ns pulse duration). The maximum of 166% laser efficiency of dye doped sol-gel samples compared to Rhodamine-6G (Rh-6G) in methanol is achieved. The photostability is also measured by using N₂ laser at 1 Hz and it is found nearly 165 pulses. The possible reasons for the photodegradation of the dye molecules are discussed in detail.     

Carbon monoxide laser emitting nanosecond pulses with 10 MHz repetition rate

Actively mode-locked electron-beam-sustained-discharge CO laser producing a train of ∼5-15 ns (FWHM) spikes following with repetition rate 10 MHz for both single-line and multiline mode of operation in the mid-IR range of ∼5 μm was experimentally studied. Total laser pulse duration was ∼0.5 ms for both mode-locked and free-running laser. Specific output energy in multiline CO laser mode of operation was up to 20 Jl⁻¹ Amagat⁻¹ and the laser efficiency up to 3.5%. The active mode-locking was achieved for single-line CO laser mode of operation in spectral range 5.2-5.3 μm. This sort of radiation can be used for pumping an optical parametric amplifier for optical stochastic cooling in relativistic heavy ion collider, for laser ablation, and for studying vibrational and rotational relaxation of CO and NO molecules.     

Characteristics of wave-breaking-free operation in a passively mode-locked all-fiber ring laser based on AS-Yb-PBGF

A passively mode-locked all-fiber ring laser is constructed based on all-solid Yb-doped photonic bandgap fibers (AS-Yb-PBGF), which provides the laser gain and anomalous dispersion simultaneously. Without any other dispersion compensators, the cavity is simple, compact, and maintenance- and alignment-free. The characteristics of wave-breaking-free operation in the laser are investigated by means of numerical simulations using the split-step Fourier method. The approximately parabolic pulses can be generated and evolved for maintaining the normal group-velocity dispersion intracavity, when the length of the single-mode fiber is between 2 and 4 m. The obtained highest energy of the output pulse is up to 2.27 nJ with the pulse duration of 8.61 ps, corresponding to the time-bandwidth product of 10.05. By dechirping out of cavity, the pulse duration is 0.70 ps.     

Production of defects in ZBLAN, ZBLAN:Tm and ZBLAN:Cr glasses by ultra-short pulses laser interaction

In this work we have studied pure and thulium- and chromium-doped ZBLAN glasses irradiated by ultra-short laser pulses. A Ti:sapphire CPA system was used, producing a 500 Hz train of pulses, centered at 830 nm, with 375 μJ of energy and 50 fs of duration (FWHM). The beam was focused by a 20 mm lens, producing a converging beam with a waist of 12 μm. The absorption spectra before and after laser irradiation were obtained showing production of color centers in pure, thulium-doped and chromium-doped ZBLAN glasses. A damage threshold of 9.56 T W/cm² was determined for ZBLAN.     

Tunable, μs-pulsed ytterbium fiber laser system with a linewidth below 2.7 GHz

We report on a widely tunable, pulsed laser system with narrow spectral linewidth based on a continuous wave ytterbium fiber oscillator, a pulse shaper and a power amplifier stage. The system is tunable from 1055 nm to 1085 nm and provides a maximum pulse energy of 155 μJ with a pulse duration of 1-5 μs. The linewidth is less than 2.7 GHz over the whole tuning range.