First-principles study on the catalytic role of Ag in the oxygen adsorption of LaMnO3(0 0 1) surface

In the present paper, the catalytic role of Ag in the oxygen adsorption of LaMnO₃(0 0 1) surface has been theoretically investigated using first-principles calculations based on the density functional theory (DFT) and pseudopotential method. The O₂ adsorption energy is larger for the vertical adsorption and the covalent bond was formed between O₂ molecule and surface Mn. The calculation of electronic properties of interaction between Ag atom and LaMnO₃(0 0 1) surface demonstrates that the most stable position for Ag adsorption is hollow site. The O₂ adsorption energy dramatically increased from 0.298 eV to 1.108 eV due to Ag pre-adsorbed. It is Ag pre-adsorbed that facilitates O₂ adsorption on surface. The bond length and bond population of O₂ molecule indicate that Ag atom facilitates O₂ molecule dissociative adsorption. The Ag atom strengthens LaMnO₃(0 0 1) substrate activity and activity center was formed on surface, which enhances the electrocatalytic activity of LaMnO₃ as solid oxide fuel cells cathode material at low temperature.     

Theoretical studies of the structure of C2H2 adsorbed on Si(0 0 1)

The carbon 1s near-edge X-ray absorption fine structure (NEXAFS) spectra of the acetylene (C₂H₂) at 1 ML coverage adsorbed on the Si(0 0 1)-(2 × 1) surface at room temperature have been investigated by multiple-scattering cluster (MSC). The MSC result shows that the correct adsorption model of C₂H₂/Si(0 0 1)-(2 × 1) is unique, i.e. the dimerized structure with two domains, (2 × 1) and (1 × 2).     

The local structure of SO2 and SO3 on Ni(1 1 1)

The normal incidence X-ray standing wave (NIXSW) technique, supported by X-ray photoelectron spectroscopy and near-edge X-ray absorption fine structure (NEXAFS), has been used to determine the local adsorption geometry of SO₂ and SO₃ on Ni(1 1 1). Chemical-state specific NIXSW data for coadsorbed SO₃ and S, formed by the disproportionation of adsorbed SO₂ after heating from 140 K to 270 K, were obtained using S 1s photoemission detection. For adsorbed SO₂ at 140 K the new results confirm those of an earlier study [Jackson et al., Surf. Sci. 389 (1997) 223] that the molecule is located above hollow sites with its molecular plane parallel to the surface and the S and O atoms in off-atop sites; corrections to account for the non-dipole effects in the interpretation of the NIXSW monitored by S 1s and O 1s photoemission, not included in the earlier work, remove the need for any significant adsorption-induced distortion of the SO₂ in this structure. SO₃, not previously investigated, is found to occupy an off-bridge site with the C_3v axis slightly tilted relative to the surface normal and with one O atom in an off-atop site and the other two O atoms roughly between bridge and hollow sites. The O atoms are approximately 0.87 Å closer to the surface than the S atom. This general bonding orientation for SO₃ is similar to that found on Cu(1 1 1) and Cu(1 0 0) both experimentally and theoretically, although the detailed adsorption sites differ.     

Angular distributions of desorbing N2 in thermal N2O decomposition on Rh(1 0 0)

The angular distribution of desorbing N₂ was studied in the decomposition of N₂O(a) on Rh(1 0 0) at 60-140 K by means of angle-resolved temperature-programmed desorption. N₂ desorption shows two peaks at around 80 K and 110 K. At low N₂O coverage, the former collimates far from the surface normal toward the [0 0 1] direction, whereas at high coverage, the desorption sharply collimates along the surface normal. The adsorption form of N₂O and its dissociation were also examined by DFT-GGA calculations. Dissociating N₂O is proposed to be lying along the [0 0 1] direction at low coverage and to change to an upright form bonding through the terminal oxygen at high coverage.     

Adsorption of water on TiN (1 0 0), (1 1 0) and (1 1 1) surfaces: A first-principles study

We use first-principles density functional theory-based calculations in the analysis of the interaction of H₂O with (1 0 0), (1 1 0) and (1 1 1) surfaces of TiN, and develop understanding in terms of surface energies, polarity of the surface and chemistry of the cation, through comparison with H₂O adsorption on ZrN. While water molecule physisorbs preferentially at Ti site of (1 0 0) and (1 1 1) surfaces, it adsorbs dissociatively on (1 1 0) surface of TiN with binding stronger than almost 1.32 eV/molecule. Our analysis reveals the following general trends: (a) surfaces with higher energies typically lead to stronger adsorption, (b) dissociative adsorption of H₂O necessarily occurs on a charge neutral high energy surface and (c) lower symmetry of the (1 1 0) plane results in many configurations of comparable stability, as opposed to the higher symmetry (1 0 0) and (1 1 1) surfaces, which also consistently explain the results of H₂O adsorption on MgO available in literature. Finally, weaker adsorption of H₂O on TiN than on ZrN can be rationalized in terms of greater chemical stability of Ti arising from its ability to be in mixed valence.     

First-principles calculations of hydrogen molecule adsorption on Ti (0 0 0 1)-(2 × 1) surface

Adsorption of H₂ molecule on the Ti (0 0 0 1)-(2 × 1) surface was studied by density functional theory with generalized gradient approximation (GGA). The parallel and vertical absorption cases were investigated in detail by adsorption energy and electronic structure analysis, we obtained three stable configurations of FCC-FCC (the two H atoms adsorption on the two adjacent fcc sites of Ti (0 0 0 1) surface, respectively), HCP-HCP (the two H atoms adsorption on the two adjacent hcp sites of Ti (0 0 0 1) surface, respectively) and FCC-HCP (the one H atom adsorption on the fcc site and the other adsorption on the near hcp site) based on the six different parallel adsorption sites after the H₂ molecule dissociates. However, all the end configurations of four vertical adsorption sites were unstable, H₂ molecule was very easy to desorb from Ti surface. The H-H bond breaking and Ti-H bond forming result from the H₂ molecule dissociation. H-H bond breaking length ranges from 1.9 Å to 2.3 Å for different adsorption configurations due to the strong Ti-H bond forming. The H₂ dissociative approach and the end stable configurations formation in parallel adsorption processes are attributed to the quantum mechanics steering effects.     

Adsorption of CO, CO2 and NO molecules on a BaTiO3 (0 0 1) surface

Since the development of Scanning Tunnelling Microscopy (STM) technique, considerable attention has been devoted to various molecules adsorbed on various surfaces. Also, a new concept emerged with molecules on surfaces considered as nano machines by themselves. In this context, a thorough knowledge of surfaces and adsorbed molecules at an atomic scale are thus particularly invaluable. The present work describes the first Density Functional Theory (DFT) study of adsorption of CO, CO₂ and NO molecules on a BaTiO₃ surface following a first preliminary calculation of O and O₂ adsorption on the same surface. In the previously considered work, we found that a (0 0 1) surface with BaO termination is more stable than the one with TiO₂-termination. Consequently, we extended our study to CO, CO₂ and NO molecules adsorbed on a (0 0 1) surface with BaO termination. The present calculation was performed on a (1 × 1) cell with one monolayer of adsorbed molecules. Especially, a series of cases implying CO molecules adsorbed in various geometrical configurations has been examined. The corresponding adsorption energy varies in the range of −0.17 to −0.10 eV. The adsorption energy of a CO₂ molecule directly located above an O surface atom (called O_s) is of the order of −0.18 eV. The O-C distance length is then 1.24 Å and the O-C-O and O-C-O_s angles are 134.0° and 113.0°, respectively. For NO adsorption, the most important induced structural changes are the followings: (i) the N-O bond is broken when a NO molecule is absorbed on a Ba-O_s bridge site. In that case, N and O atoms are located above an O and a Ba surface atom, respectively, whereas the O-Ba-O_s and N-O_s-Ba angles are 106.5° and 63.0°, respectively. The N-O distance is as large as 2.58 Å and the adsorption energy is as much as −2.28 eV. (ii) In the second stable position, the NO molecule has its N atom adsorbed above an O_s atom, the N-O axis being tilted toward the Ba atom. The N-O_s-Ba angle is then 41.1° while the adsorption energy is only −0.10 eV. At last, the local densities of states around C, O as well as N atoms of the considered adsorbed molecules have also been discussed.     

Reaction mechanism for CO oxidation on Cu(3 1 1): A density functional theory study

The microscopic reaction mechanism for CO oxidation on Cu(3 1 1) surface has been investigated by means of comprehensive density functional theory (DFT) calculations. The elementary steps studied include O₂ adsorption and dissociation, dissociated O atom adsorption and diffusion, as well as CO adsorption and oxidation on the metal. Our results reveal that O₂ is considerably reactive on the Cu(3 1 1) surface and will spontaneously dissociate at several adsorption states, which process are highly dependent on the orientation and site of the adsorbed oxygen molecule. The dissociated O atom may likely diffuse via inner terrace sites or from a terrace site to a step site due to the low barriers. Furthermore, we find that the energetically most favorable site for CO molecule on Cu(3 1 1) is the step edge site. According to our calculations, the reaction barrier of CO + O → CO₂ is about 0.3 eV lower in energy than that of CO + O₂ → CO₂ + O, suggesting the former mechanism play a main role in CO oxidation on the Cu(3 1 1) surface.     

Structures and stability of Ag clusters on Ag(1 1 1) and Ni(1 1 1) surfaces

The structures of the lowest total energy for small Ag_N clusters with N = 2-20, which are grown on Ag(1 1 1) and Ni(1 1 1) surfaces, have been determined using a combination of the embedded-atom method and the basin-hopping algorithm. It is found that the particularly stable Ag clusters with N<18 have similar geometries on both surfaces when comparing clusters of the same size. On the other hand, the geometries of the less stable Ag clusters in the same size range differ for the two surfaces. From N?18, the sizes of the particularly stable structures are different for the two different substrates. Due to the large size mismatch of the two types of atoms it is energetically unfavorable for Ag to form a pseudomorphic monolayer structures on Ni(1 1 1) and there is considerable strain produced at the interface. The effect of this strain and the increased adatom-substrate interactions lead to irregular and elongated structures of the adsorbed Ag clusters.     

The adsorption of and reaction of NO2 on Ag(1 1 1)-p(4 × 4)-O and formation of surface nitrate

The adsorption and reaction of nitrogen dioxide on the Ag(1 1 1)-p(4 × 4)-O surface has been investigated with RAIRS, TPRS and STM. At 300 K NO₂ initially reacts with the oxygen overlayer to form nitrate in p(3 × 3) and p(4 × 4) structures, which convert to a new p(3 × 3) at saturation coverage. Surface pitting during nitrate adsorption is suggestive of the incorporation of silver atoms into the NO₃ structure. With heating NO₃ decomposes into NO₂ and O at 396 K and 497 K, and oxygen desorbs at 578 K.     

Metal film growth on regular and defective MgO(0 0 1) surface: A comparative ab initio simulation and thermodynamic study

In order to understand the difference in metallic film growth modes on perfect and defective oxide substrates, we have combined ab initio B3LYP periodic calculations on the slab models of the corresponding Me/MgO(0 0 1) interfaces (Me = Ag, Cu) with thermodynamic theory of solid solutions. For a defectless magnesia surface, we confirm the experimentally observed submonolayer growth of 3D metallic islands (Ag possesses a higher trend than Cu). Formation of F_s centers (neutral O vacancies) on the substrate markedly enhances metal atom adsorption as compared to physisorption over regular sites on a defect-free substrate. For the first time, we predict that the presence of these surface defects (beginning with concentrations of 5% for Cu and 22% for Ag) can stimulate the growth of uniform 2D metallic sublayers.     

A density-functional study on the atomic geometry and adsorption of the Cu(1 0 0) c(2 × 2)/N Surface

In this work we have performed total-energy calculations on the geometric structure and adsorption properties of Cu(1 0 0) c(2 × 2)/N surface by using the density-functional theory and the projector-augmented wave method. It is concluded that nitrogen atom was adsorbed on a FFH site with a vertical distance of 0.2 Å towards from surface Cu layer. The bond length of the shortest Cu-N bonding is calculated to be 1.83 Å. Geometry optimization calculations exclude out the possibilities of adsorbate induced reconstruction mode suggested by Driver and Woodruff and the atop structural model. The calculated workfunction for this absorbate-adsorbent system is 4.63 eV which is quite close to that of a clean Cu(1 0 0) surface. The total-energy calculations showed that the average adsorption energy per nitrogen in the case of Cu(1 0 0) c(2 × 2)-N is about 4.88 eV with respect to an isolated N atom. The absorption of nitrogen on Cu(1 0 0) surface yields the hybridization between surface Cu atoms and N, and generates the localized surface states at −1.0 eV relative to Fermi energy E_F. The stretch mode of the adsorbed nitrogen at FFH site is about 30.8 meV. The present study provides a strong criterion to account for the local surface geometry in Cu(1 0 0) c(2 × 2)/N surface.     

Density functional theory calculations of surface properties and H2 adsorption on the Cu2O (1 1 1) surface

First-principles calculation on the basis of the density functional theory (DFT) and generalized gradient approximation have been applied to study the adsorption of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1), Cu₂O (1 1 1)-Cu_CUS and Cu-terminated Cu₂O (1 1 1) surfaces. The optimal adsorption position and orientation of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1) surface and Cu-terminated Cu₂O (1 1 1) surface were determined and electronic structural changes upon adsorption were investigated by calculating the Local Density of States (LDOS) of the Cu_CUS 3d and Cu_CUS 4s of stoichiometric O-terminated Cu₂O (1 1 1) surface. These results showed that H₂ molecule adsorption on Cu_CUS site parallel to stoichiometric O-terminated Cu₂O (1 1 1) surface and H₂ molecule adsorption on Cu₂ site parallel to Cu-terminated Cu₂O (1 1 1) surface were the most favored, respectively. The presence of surface copper vacancy has a little influence on the structures when H₂ molecule adsorbs on Cu_CSA, O_CUS and O_CSA atoms and the H₂ molecule is only very weakly bound to the Cu₂O (1 1 1)-Cu_CUS surface. From the analysis of stoichiometric O-terminated Cu₂O (1 1 1) Local Density of States, it is observed that Cu_CUS 3d orbital has moved to a lower energy and the sharp band of Cu_CUS 4s is delocalized when compared to that before H₂ molecule adsorption, and overlapped substantially with bands due to adsorbed H₂ molecule. The Mulliken charges of H₂ adsorption on Cu_CUS site showed that H₂ molecule obtained electron from Cu_CUS which was consistent with the calculated electronic structural changes upon H₂ adsorption.     

Adsorption of phenylalanine on single crystal rutile TiO2(1 1 0) surface

The adsorption of the aromatic amino acid, phenylalanine on a TiO₂ rutile (1 1 0) single crystal surface has been investigated with photoemission and NEXAFS (near edge X-ray absorption fine structure) spectroscopy. The results indicate initial adsorption via the carboxylate group in a bidentate configuration with the phenyl ring oriented at approximately 25° to the surface normal. The amino group remains as NH₂. Subsequent layers of phenylalanine appear to adsorb as neutral molecules with H-bonding between NH₂ and CO groups.     

Density functional study of oxygen adsorption on the Mg3Nd (0 0 1) surface

The adsorption of oxygen atoms on Mg₃Nd (0 0 1) surface was studied based on density function theory (DFT), in which the exchange-correlation potential was chosen as the generalized gradient approximation (GGA) in the Perdew and Wang (PW91). The most preferred adsorption position was at the top-hollow site. Upon the optimization on top-hollow site with different coverage, it was found that the adsorption energy decreased with oxygen coverage. The density of states analysis showed that obvious charge transfer took place between O atom and the nearest Nd atom and chemical bond formed between O atom and the nearest Nd atom after O adsorption. The result of surface energy as a function of chemical potential change of oxygen indicated the clean Mg₃Nd (0 0 1) surface was easy to adsorb oxygen and form 1.00 ML surface.     

Adsorption and dissociation of O2 on CuCl(1 1 1) surface: A density functional theory study

The adsorption and dissociation of O₂ on CuCl(1 1 1) surface have been systematically studied by the density functional theory (DFT) slab calculations. Different kinds of possible modes of atomic O and molecular O₂ adsorbed on CuCl(1 1 1) surface and possible dissociation pathways are identified, and the optimized geometry, adsorption energy, vibrational frequency and Mulliken charge are obtained. The calculated results show that the favorable adsorption occurs at hollow site for O atom, and molecular O₂ lying flatly on the surface with one O atom binding with top Cu atom is the most stable adsorption configuration. The O-O stretching vibrational frequencies are significantly red-shifted, and the charges transferred from CuCl to oxygen. Upon O₂ adsorption, the oxygen species adsorbed on CuCl(1 1 1) surface mainly shows the characteristic of the superoxo (O₂⁻), which primarily contributes to improving the catalytic activity of CuCl, meanwhile, a small quantity of O₂ dissociation into atomic O also occur, which need to overcome very large activation barrier. Our results can provide some microscopic information for the catalytic mechanism of DMC synthesis over CuCl catalyst from oxidative carbonylation of methanol.     

First-principles calculations of C diffusion through the surface and subsurface of Ag/Ni(1 0 0) and reconstructed Ag/Ni(1 0 0)

Density functional theory calculations are performed to investigate the C diffusion through the surface and subsurface of Ag/Ni(1 0 0) and reconstructed Ag/Ni(1 0 0). The calculated geometric parameters indicate the center of doped Ag is located above the Ni(1 0 0) surface owing to the size mismatch. The C binding on the alloy surface is substantially weakened, arising from the less attractive interaction between C and Ag atoms, while in the subsurface, the C adsorption is promoted as the Ag coverage is increased. The effect of substitutional Ag on the adsorption property of Ni(1 0 0) is rather short-range, which agrees well with the analysis of the projected density of states. Seven pathways are constructed to explore the C diffusion behavior on the bimetallic surface. Along the most kinetically favorable pathway, a C atom hops between two fourfold hollow sites via an adjacent octahedral site in the subsurface of reconstructed Ag/Ni(1 0 0). The “clock” reconstruction which tends to improve the surface mobility, is more favorable on the alloy surface because the c(2 × 2) symmetry is inherently broken by the Ag impurity. As a consequence, the local lattice strain induced by the C transport is effectively relieved by the Ag-enhanced surface mobility and the C diffusion barrier is lowered from 1.16 to 0.76 eV.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Thermal stability of nanoscale silver metallization in Ag/W/Co/Si(1 0 0) multilayer

In this work, we have studied thermal stability of nanoscale Ag metallization and its contact with CoSi₂ in heat-treated Ag(50 nm)/W(10 nm)/Co(10 nm)/Si(1 0 0) multilayer fabricated by sputtering method. To evaluate thermal stability of the systems, heat-treatment was performed from 300 to 900 °C in an N₂ ambient for 30 min. All the samples were analyzed by four-point-probe sheet resistance measurement (R_s), Rutherford backscattering spectrometry (RBS), X-ray diffractometry (XRD), and atomic force microscopy (AFM). Based on our data analysis, no interdiffiusion, phase formation, and R_s variation was observed up to 500 °C in which the Ag layer showed a (1 1 1) preferred crystallographic orientation with a smooth surface and R_s of about 1 Ω/□. At 600 °C, a sharp increase of R_s value was occurred due to initiation of surface agglomeration, WSi₂ formation, and interdiffusion between the layers. Using XRD spectra, CoSi₂ formed at the Co/Si interface preventing W silicide formation at 750 and 800 °C. Meantime, RBS analysis showed that in this temperature range, the W acts as a cap layer, so that we have obtained a W encapsulated Ag/CoSi₂ contact with a smooth surface. At 900 °C, the CoSi₂ layer decomposed and the layers totally mixed. Therefore, we have shown that in Ag/W/Co/Si(1 0 0) multilayer, the Ag nano-layer is thermally stable up to 500 °C, and formation of W-capped Ag/CoSi₂ contact with R_s of 2 Ω/□ has been occurred at 750-800 °C.