Auger electron spectroscopic study of CO2 adsorption on Zircaloy-4 surfaces

We investigate the adsorption of CO₂ onto Zircaloy-4 (Zry-4) surfaces at 150, 300 and 600 K using Auger electron spectroscopy (AES). Following CO₂ adsorption at 150 K the graphitic form of carbon is detected, whereas upon chemisorption at 300 and 600 K we detect the carbidic phase. As the adsorption temperature is increased, the carbon Auger signal increases, whereas the oxygen signal decreases. Adsorption at all three temperatures results in a shift of the Zr Auger features, indicating surface oxidation. The effect of adsorbed CO₂ on the Zr(MVV) and Zr(MNV) transitions depends on adsorption temperature and is less pronounced at higher temperatures. On the other hand, changes in the Zr(MNN) feature are similar for all three adsorption temperatures. The changes in the Zr Auger peak shapes and positions are attributed to oxygen from dissociated CO₂, with the differences observed at various temperatures indicative of the diffusion of oxygen into the subsurface region.     

Laser induced thermal desorption of hydrogen from Zr(0 0 0 1): Relationship to water dissociation and hydrogen dissolution

On metals such as Zr, during hydrogen exposure, dissolution competes with desorption; this competition can be probed by thermal desorption at different heating rates. In the case of desorption from preadsorbed hydrogen, only ∼1% of the hydrogen can be desorbed even at heating rates of >10¹⁰ K s⁻¹. Recent measurements of the dynamics of hydrogen released by water dissociation on Zr(0 0 0 1) [G. Bussière, M. Musa, P.R. Norton, K. Griffiths, A.G. Brolo, J.W. Hepburn, J. Chem. Phys. 124 (2006) 124704] have shown that the desorbing hydrogen originates from the recombinative desorption of adsorbed H-atoms and that over 25% of the water collisions lead to hydrogen desorption. To gain further insight into the desorption and dissolution of hydrogen and in an attempt to resolve the paradox of the different desorption yields from H₂ vs. H₂O exposures, we report new measurements of the laser induced thermal desorption (LITD) of hydrogen from Zr(0 0 0 1) at initial temperatures down to 90 K. The low temperature was chosen because work function measurements suggested that hydrogen adsorbed into only the outermost (surface site) of the two available adsorption sites (surface and subsurface), from which we postulated much more efficient desorption at high heating rates compared to desorption from the sub-surface sites. However, hydrogen desorption by LITD from Zr(0 0 0 1) at 90 K still only accounts for 1% of the adsorbed species, the remainder dissolving into the bulk at LITD heating rates. The different yields alluded to above remain unexplained (Bussière, 2006).     

The adsorption of CCl4 on Ag(1 1 1): Carbene and CC bond formation

The adsorption of CCl₄ on Ag(1 1 1) has been investigated from 100 K to 300 K using absolute sticking probability measurement, temperature programmed desorption, Auger electron spectroscopy, low energy electron diffraction, ultra-violet photoelectron spectroscopy and X-ray photoelectron spectroscopy. At 100 K, CCl₄ adsorbs molecularly with a sticking probability of 1.0, forming a (3 × 3) adsorption structure. At 300 K the following overall reaction occurs,

2CCl_4(g)→4Cl_(chem)+C₂Cl_4(g),     

Site-specific interaction of H2O with ZnO single-crystal surfaces studied by thermal desorption and UV photoelectron spectroscopy

The adsorption and condensation of H₂O(D₂O) on ZnO(101̄0), (0001)Zn and (0001̄)O surfaces was investigated by means of thermal desorption (TDS) and UV photoelectron spectroscopy (UPS). The clean ZnO single-crystal surfaces were prepared by Ar-ion sputtering and annealing and characterised by Auger electron spectroscopy, LEED, UPS and work-function measurements. On all three surfaces six different adsorption states were found. In the monolayer regime there is a stronger bonding to Zn sites (desorption temperature 340 K) than to O sites (190 K), The bonding to the Zn sites seems to be accompanied by some clustering. Before the chemisorption layer is completed a first ice state is found whose desorption temperature shifts from 162 to 168 K with increasing exposures. At higher exposures the multilayer ice state is found at 152 K. On the (0001̄)O face defect-induced features were identified. The water lone-pair orbital 1b₁, whose energy falls between the O p and the Zn 3d emission of the substrate and which is known to show bonding shifts, was analysed using angle-resolved UPS. In the monolayer, the main chemisorption states are found at E_B^V(1b₁) = ?9.6 eV for the (0001)Zn face and at ? 10.6 eV for the (0001̄)O face and are compared with the multilayer ice emission at 1̄1.1 eV. The difference in binding energies shows the same trend as the TDS data. For the (101̄0) face the 1b₁ emission is very broad, indicating some overlap between different states.     

Angular distributions of desorbing N2 in thermal N2O decomposition on Rh(1 0 0)

The angular distribution of desorbing N₂ was studied in the decomposition of N₂O(a) on Rh(1 0 0) at 60-140 K by means of angle-resolved temperature-programmed desorption. N₂ desorption shows two peaks at around 80 K and 110 K. At low N₂O coverage, the former collimates far from the surface normal toward the [0 0 1] direction, whereas at high coverage, the desorption sharply collimates along the surface normal. The adsorption form of N₂O and its dissociation were also examined by DFT-GGA calculations. Dissociating N₂O is proposed to be lying along the [0 0 1] direction at low coverage and to change to an upright form bonding through the terminal oxygen at high coverage.     

CO adsorption and dissociation on iron oxide supported Pt particles

We studied CO adsorption on Pt particles deposited on well-ordered Fe₃O₄(1 1 1) thin films grown on Pt(1 1 1) by temperature programmed desorption (TPD). A highly stepped Pt(1 1 1) surface produced by ion sputtering and annealing at 600 K was studied for comparison. Structural characterization was performed by scanning tunneling microscopy and Auger electron spectroscopy. The TPD spectra revealed that in addition to the desorption peaks at ∼400 and 480 K, assigned to CO adsorbed on Pt(1 1 1) facets and low-coordination sites respectively, the Pt nanoparticles annealed at 600 K exhibit a desorption state at ∼270 K. This state is assigned to initial stages of strong metal support interaction resulting in partial Fe-Pt intermixing. On both Pt/Fe₃O₄(1 1 1) and stepped Pt(1 1 1) surfaces CO is found to dissociate at 500 K. The results suggest that CO dissociation and carbon accumulation occur on the low-coordinated Pt sites.     

Interaction of H2O with the RuO2(1 1 0) surface studied by HREELS and TDS

The adsorption of water on a RuO₂(1 1 0) surface was studied by using high-resolution electron energy loss spectroscopy (HREELS) and thermal desorption spectroscopy (TDS). The first thermal desorption peak observed between 350 and 425 K is attributed to molecular water adsorbed on fivefold coordinated Ru_cus sites. Higher coverages of water give rise to TDS peaks between 190 and 160 K, which we attribute to water in the second layer bound to bridge oxygen, and multilayers, respectively. HREELS shows that H₂O chemisorbs on Ru_cus sites through oxygen inducing a slight red shift of the vibrational frequency of O_bridge atoms. Molecular adsorption is also confirmed by the presence of both the scissor and the libration modes showing the expected isotopic shift for D₂O. The water adsorbed on the Ru_cus sites also forms hydrogen bonds with the bridge oxygen indicated by the broad intensity at the lower frequency side of the O-H stretch mode. HREELS and TDS results suggest that on the perfect RuO₂(1 1 0) surface water dissociation is almost negligible.     

Modification of ferroelectric hysteresis in Pb(Nb,Zr,Ti)O3 thin films induced by CO2 adsorption

We report on the modification of ferroelectric hysteresis in Pb(Nb,Zr,Ti)O₃ thin films under the adsorption of CO₂ gas. The samples were exposed to the gas in ultra high vacuum while different voltages between the top (Ag) and bottom (Pt) electrodes were applied. After dosing, the samples were heated from room temperature at 1.8 K/s, and a mass spectrometer was used to detect the desorbed molecules. The effective molecular sticking was demonstrated by the appearance of the carbon Auger peak in the surface of the sample and by the presence of CO₂ in the desorption curves. After +(−) 9.9 V were applied to the bottom electrode during dosing, we found a shift of −0.52 (+0.58) μC/cm² in the remnant polarization. These evidences suggest the existence of a depolarizing field induced by molecular adsorption at the surface of the top electrode, and contribute to highlight the potential use of ferroelectric thin films as gas sensors.     

Interactions of water vapor with polycrystalline uranium surfaces - The low temperature regime

The initial interaction of water vapor with polycrystalline uranium surfaces at low temperatures (LT, 200 K), was studied by combined measurements utilizing Direct Recoil Spectrometry (DRS), Auger electron Spectroscopy (AES) and X-ray Photoelectron Spectroscopy (XPS). Three stages of water dissociation and adsorption can be observed: Stage (1) 0-0.6 oxygen monolayer coverage: full (H₂O → O + 2H) dissociation is dominant, coexisting with partial dissociation (H₂O → OH + H). In contrast to room temperature, where the adsorption is of a Langmuir type, in the present low temperature case it is a precursor-state type - the oxygen accumulation is linear, indicating that a constant fraction of the water molecules impinging on the surface diffuses to a dissociation and adsorption site. Only minor oxidation of the uranium occurs. Stage (2) 0.6-full oxygen coverage: only partial dissociation occurs. Still only minor oxidation of uranium takes place. Stage (3) buildup of a second hydroxyl layer, concurrent with slow continuous oxidation of uranium. Subsequent heating of the sample after the described exposure was accompanied by additional continuous oxidation. Above ∼230 K, the main process seems to be OH decomposition and desorption. A comparison is made to the dissociation and adsorption processes at room temperature.     

Spectroscopic study on thermal reaction and desorption of sulfur/Rh(1 0 0) induced by oxygen-containing molecules

The surface reaction and desorption of sulfur on Rh(1 0 0) induced by O₂ and H₂O are investigated with X-ray photoelectron spectroscopy (XPS) technique. The Rh(1 0 0) sample covered with atomic sulfur is prepared by means of the exposure to H₂S gas, and subsequently the sample is annealed under O₂ or H₂O atmosphere. The XPS results show that atomic sulfur adsorbed on Rh(1 0 0) reacts with O₂ and desorbs from the surface at 473 K or more. On the other hand, atomic sulfur can not be removed from Rh(1 0 0) surface by H₂O at any temperature.     

Adsorption and reaction of hydrogen sulfide on thin-film cerium oxide

The adsorption and reaction of hydrogen sulfide, H₂S, have been studied on cerium oxide thin films that were vapor deposited on Ru(0 0 0 1). The behavior of the H₂S was examined as a function of Ce oxidation state. H₂S weakly chemisorbs on fully oxidized CeO₂ desorbing near 155 K. Hydrogen from the H₂S reacts with the surface O to desorb as water between 200 K and 450 K. When ca. 20% of the Ce⁴⁺ is reduced to Ce³⁺ more H₂S dissociates to -OH and -SH and water is produced near 580 K. When the ceria is ca. 70% reduced, water formation is suppressed and H₂ desorbs near 580 K. S 2p photoelectron spectroscopy indicates the decomposition of H₂S into -SH and then -S as the sample is annealed from 100 K to 600 K. O 1s photoemission indicated the presence of H₂O and -OH.     

Simulation of thermal desorption spectra of N2 observed during N2O decomposition on Rh(1 0 0)

Our measurements indicate that under temperature-programmed conditions the N₂O decomposition occurs on Rh(1 0 0) between 60 and 140 K and results in the appearance of two N₂ desorption peaks related to N₂ molecules leaving the surface during and after N₂O dissociation events, respectively. Both peaks are observed even at low initial coverages. This and other features of N₂ desorption are explained by using Monte Carlo simulations taking into account attractive N₂O-O lateral interactions stabilizing N₂O adsorption. The results presented are compared with those obtained earlier for Rh(1 1 0).     

Adsorption of glycine on a NiAl(1 1 0) alloy surface

The adsorption and desorption of glycine (NH₂CH₂COOH), vacuum deposited on a NiAl(1 1 0) surface, were investigated by means of Auger electron spectroscopy (AES), low energy electron diffraction (LEED), temperature-programmed desorption, work function (Δφ) measurements, and ultraviolet photoelectron spectroscopy (UPS). At 120 K, glycine adsorbs molecularly forming mono- and multilayers predominantly in the zwitterionic state, as evidenced by the UPS results. In contrast, the adsorption at room temperature (310 K) is mainly dissociative in the early stages of exposure, while molecular adsorption occurs only near saturation coverage. There is evidence that this molecularly adsorbed species is in the anionic form (NH₂CH₂COO⁻). Analysis of AES data reveals that upon adsorption glycine attacks the aluminium sites on the surface. On heating part of the monolayer adsorbed at 120 K is converted to the anionic form and at higher temperatures dissociates further before desorption. The temperature-induced dissociation of glycine (<400 K) leads to a series of similar reaction products irrespective of the initial adsorption step at 120 K or at 310 K, leaving finally oxygen, carbon and nitrogen at the surface. AES and LEED measurements indicate that oxygen interacts strongly with the Al component of the surface forming an “oxide”-like Al-O layer.     

Oxygen-induced nano-faceting of Ir(2 1 0)

The adsorption of oxygen and the nanometer-scale faceting induced by oxygen have been studied on Ir(2 1 0). Oxygen is found to chemisorb dissociatively on Ir(2 1 0) at room temperature. The molecular desorption process is complex, as revealed by a detailed kinetic analysis of desorption spectra. Pyramid-shaped facets with {3 1 1} and (1 1 0) orientations are formed on the oxygen-covered Ir(2 1 0) surface when annealed to T?600 K. The surface remains faceted for substrate temperatures T<850 K. For T>850 K, the substrate structure reverts to the oxygen-covered (2 1 0) planar state and does so reversibly, provided that oxygen is not lost due to desorption or via chemical reactions upon which the planar (2 1 0) structure remains. A clean faceted surface was prepared through the use of low temperature surface cleaning methods: using CO oxidation, or reaction of H₂ to form H₂O, oxygen can be removed from the surface while preserving (“freezing”) the faceted structure. The resulting clean faceted surface remains stable for T<600 K. For temperatures above this value, the surface irreversibly relaxes to the planar state.     

CO2 adsorption on the bimetallic Zn-on-Cu(1 1 0) system

Adsorption probability measurements (molecular beam scattering) have been conducted to examine the adsorption dynamics (i.e. the gas-surface energy transfer processes) of CO₂ adsorption on the Zn-on-Cu(1 1 0) bimetallic system. The results indicate surface alloy formation, which is in agreement with prior studies. Depositing Zn at 300 K on Cu(1 1 0), above the condensation temperature of CO₂, leads to a “blocking” of CO₂ adsorption sites by Zn which is incorporated in the Cu(1 1 0) surface. This apparent site blocking effect indicates a lowering of the CO₂ binding energy on the alloyed surface as compared with the clean Cu(1 1 0) support. The Zn coverage has been calibrated by Auger electron spectroscopy and thermal desorption spectroscopy.     

Adsorption of H2O on clean and on boron-contaminated Rh surfaces

The adsorption and dissociation of H₂O on Rh(111) and Rh foil surfaces have been studied in UHV using Auger electron, electron energy loss (in the electronic range) and thermal desorption spectroscopy. H₂O adsorbs weakly on clean Rh samples at 110 K. The adsorption is accompanied by the appearance of a broad loss feature at 14–14.5 eV. At higher exposures new losses appeared at 8.6 and 10.5 eV. The desorption of H₂O took place in two stages, with T_p = 183 K (β, chemisorption) and 158 K (α, multilayer formation). There was no indication of dissociation of H₂O on a clean Rh(111) surface. Similar results were obtained for a clean Rh foil. However, when small amounts of boron segregated on the surface of Rh, they exerted a dramatic influence on the adsorptive properties of this surface and caused the dissociation of H₂O. This was exhibited by the formation of H₂, by the buildup of surface oxygen, by the appearance of an intense new loss at 9.4 eV, identified as B-O surface species, and by the development of “boron-oxide”-like Auger fine structure.     

Site-blocking effects of preadsorbed H on Pt(1 1 1) probed by 1,3-butadiene adsorption and reaction

The influence of hydrogen coadsorption on hydrocarbon chemistry on transition metal surfaces is a key aspect to an improved understanding of catalytic selective hydrogenation. We have investigated the effects of H preadsorption on adsorption and reaction of 1,3-butadiene (H₂CCHCHCH₂, C₄H₆) on Pt(1 1 1) surfaces by using temperature-programmed desorption (TPD) and Auger electron spectroscopy (AES). Preadsorbed hydrogen adatoms decrease the amount of 1,3-butadiene chemisorbed on the surface and chemisorption is completely blocked by the hydrogen monolayer (saturation) coverage (θ_H = 0.92 ML). No hydrogenation products of reactions between coadsorbed H adatoms and 1,3-butadiene were observed to desorb in TPD experiments over the range of θ_H investigated (θ_H = 0.6-0.9 ML). This is in strong contrast to the copious evolution of ethane (CH₃CH₃, C₂H₆) from coadsorbed hydrogen and ethylene (CH₂CH₂, C₂H₄) on Pt(1 1 1). Hydrogen adatoms effectively (in a 1:1 stoichiometry) remove sites from interaction with chemisorbed 1,3-butadiene, but do not affect adjacent sites. The adsorption energy of coadsorbed 1,3-butadiene is not affected by the presence of hydrogen on Pt(1 1 1). The chemisorbed 1,3-butadiene on hydrogen preadsorbed Pt(1 1 1) completely dehydrogenates to H₂ and surface carbon upon heating without any molecular desorption detected, which is identical to that observed on clean Pt(1 1 1). In addition to revealing aspects of site blocking that should have broad implications for hydrogen coadsorption with hydrocarbon molecules on transition metal surfaces in general, these results also provide additional basic information on the surface science of selective catalytic hydrogenation of butadiene in butadiene-butene mixtures.     

Adsorption of H2O on Al(111)

The adsorption of H₂O on Al(111) has been studied by ESDIAD (electron stimulated desorption ion angular distributions), LEED (low energy electron diffraction), AES (Auger electron spectroscopy) and thermal desorption in the temperature range 80–700 K. At 80 K, H₂O is adsorbed predominantly in molecular form, and the ESDIAD patterns indicate that bonding occurs through the O atom, with the molecular axis tilted away from the surface normal. Some of the H₂O adsorbed at 80 K on clean Al(111) can be desorbed in molecular form, but a considerable fraction dissociates upon heating into OH_ads and hydrogen, which leaves the surface as H₂. Following adsorption of H₂O onto oxygen-precovered Al(111), additional OH_ads is formed upon heating (perhaps via a hydrogen abstraction reaction), and H₂ desorbs at temperatures considerably higher than that seen for H₂O on clean Al(111). The general behavior of H₂O adsorption on clean and oxygen-precovered Al(111) (θ_O ? monolayer) is rather similar at low temperature, but much higher reactivity for dissociative adsorption of H₂O to form OH _adsis noted on the oxygen-dosed surface around room temperature.     

Molecularly intact and dissociative adsorption of water on clean Cu(1 1 0): A comparison with the water/Ru(0 0 1) system

An X-ray photoelectron spectroscopy (XPS) study was undertaken of the water/Cu(1 1 0)-system finding non-dissociative adsorption on clean Cu(1 1 0) at temperatures below 150 K. Thermally induced dissociation of D₂O is observed to occur above 150 K, similar to the H₂O/Ru(0 0 1) system, with an experimentally derived activation barrier of 0.53-0.56 eV which is very close in magnitude to the derived activation barrier for desorption of 0.50-0.53 eV. X-ray and electron induced damage to the water overlayer was quantified and used to rationalize the results of a recent XPS study of the water/Cu(1 1 0)-system where partial dissociation was observed already at 90 K.     

Density functional theory calculations of surface properties and H2 adsorption on the Cu2O (1 1 1) surface

First-principles calculation on the basis of the density functional theory (DFT) and generalized gradient approximation have been applied to study the adsorption of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1), Cu₂O (1 1 1)-Cu_CUS and Cu-terminated Cu₂O (1 1 1) surfaces. The optimal adsorption position and orientation of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1) surface and Cu-terminated Cu₂O (1 1 1) surface were determined and electronic structural changes upon adsorption were investigated by calculating the Local Density of States (LDOS) of the Cu_CUS 3d and Cu_CUS 4s of stoichiometric O-terminated Cu₂O (1 1 1) surface. These results showed that H₂ molecule adsorption on Cu_CUS site parallel to stoichiometric O-terminated Cu₂O (1 1 1) surface and H₂ molecule adsorption on Cu₂ site parallel to Cu-terminated Cu₂O (1 1 1) surface were the most favored, respectively. The presence of surface copper vacancy has a little influence on the structures when H₂ molecule adsorbs on Cu_CSA, O_CUS and O_CSA atoms and the H₂ molecule is only very weakly bound to the Cu₂O (1 1 1)-Cu_CUS surface. From the analysis of stoichiometric O-terminated Cu₂O (1 1 1) Local Density of States, it is observed that Cu_CUS 3d orbital has moved to a lower energy and the sharp band of Cu_CUS 4s is delocalized when compared to that before H₂ molecule adsorption, and overlapped substantially with bands due to adsorbed H₂ molecule. The Mulliken charges of H₂ adsorption on Cu_CUS site showed that H₂ molecule obtained electron from Cu_CUS which was consistent with the calculated electronic structural changes upon H₂ adsorption.