XPS study of the surface chemistry of Ag-covered L-CVD SnO2 thin films

In this paper, we present the results of X-ray photoelectron spectroscopy characterization of SnO₂ thin films prepared by laser chemical vapour deposition (L-CVD) and subsequently covered by Ag atoms just after deposition and after long-term exposed to dry air, subsequent annealing in ultra high vacuum at 400 °C and dry air oxidation at 400 °C. Using the standard analytical procedure based on atomic sensitivity factors, the variation of surface chemistry defined in terms of the relative concentration of the main components of the films after the above-mentioned procedures has been determined. It was confirmed that after dry air exposure as well as dry air oxidation, the layers undergo an oxidation reaching almost SnO₂ stoichiometry. Besides, during ultra high vacuum annealing, the films undergo reduction to almost SnO stoichiometry. At the same time, Ag atoms deposited at the top of layers diffuse into the subsurface layers. This was confirmed by X-ray photoelectron spectroscopy depth profiling analysis.     

Atomic layer deposition of PbZrO3 thin films

In this paper, we report on the preparation of lead zirconate films for the first time using atomic layer deposition in an attempt to investigate some of the film properties and also to evaluate possible use of the precursor combination to prepare more complex lead titanate zirconate. In the depositions tetraphenyl lead (Ph₄Pb) was used as the lead and zirconium 2,2,6,6-tetramethyl-3,5-heptadionato (Zr(thd)₄) as the zirconium precursor, while ozone was used as the oxygen source. Film growth, stoichiometry and quality were studied using different pulsing ratios at deposition temperatures of 275 and 300 °C. According to X-ray diffraction, the crystalline perovskite phase was observed when films deposited on SrTiO₃(1 0 0) were annealed at 600 °C. Surface roughness was reduced for lead deficient films as well as in annealed samples.     

XPS depth profiling studies of L-CVD SnO2 thin films

In this paper we present the results of the XPS atomic depth profile analysis, using ion beam sputtering, of L-CVD SnO₂ thin films grown on an atomically clean SiO₂ substrate after annealing at 400 °C in dry atmospheric air. From the evolution of the Sn 3d_5/2, O 1s, Si 2p and C 1s core level peaks our experiments allowed the determination of the in depth atomic concentration of the main components of the SnO₂/SiO₂ interface. Thin (few nm) nearly stoichiometric SnO₂ films are present at the topmost layer of the thin films, and progressive intermixing with SnO and silicon oxide is observed at deeper layer. The interface between the Sn and the Si oxide layers (i.e. the effective Sn oxide thickness) is measured at 13 nm.     

Thickness influence on surface morphology and ozone sensing properties of nanostructured ZnO transparent thin films grown by PLD

Transparent zinc oxide (ZnO) thin films with a thickness from 10 to 200 nm were prepared by the PLD technique onto silicon and Corning glass substrates at 350 °C, using an Excimer Laser XeCl (308 nm). Surface investigations carried out by atomic force microscopy (AFM) and X-ray diffraction (XRD) revealed a strong influence of thickness on film surface topography. Film roughness (RMS), grain shape and dimensions correlate with film thickness. For the 200 nm thick film, the RMS shows a maximum (13.9 nm) due to the presence of hexagonal shaped nanorods on the surface. XRD measurements proved that the films grown by PLD are c-axis textured. It was demonstrated that the gas sensing characteristics of ZnO films are strongly influenced and may be enhanced significantly by the control of film deposition parameters and surface characteristics, i.e. thickness and RMS, grain shape and dimension.     

Microstructures and electrical properties of La0.8Sr0.2MnO3 films synthesized by sol-gel method

La_0.8Sr_0.2MnO₃ (LSMO) thin films were fabricated on alumina substrates by an improved sol-gel dip-coating process. It was found that multiple dip-coating process could not be performed until the pre-firing temperature reached 600 °C. Different amounts of LSMO powders were added to precursor solution with an aim to avoid cracks in LSMO thin films during calcining caused by the shrinkage mismatch between the film and the substrate. The structure and surface morphology of the films prepared from precursors with and without LSMO powders were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that the addition of 56.4 wt.% LSMO powders into the sol-gel precursor solution significantly modified the microstructure of films. A single LSMO perovskite phase was obtained on alumina substrate after calcining at 800 °C for 4 h by the improved sol-gel method. The sheet resistance of the films prepared with different processing parameters was measured by four-point dc method. Results indicated that the sheet resistance of films decreased with increasing the number of coating applications and the amount of LSMO powders.     

Electrochemical properties of electrosynthesized TiO2 thin films

Titanium dioxide (TiO₂) thin films prepared by cathodic electrodeposition on indium-tin-oxide coated glass substrates from simple aqueous peroxo-titanium complex solutions have been studied as a function of sintering temperature (25-500 °C). The films crystallized in to anatase phase at relatively low temperature (300 °C). Electrochemical properties of amorphous and anatase films were investigated by cyclic voltammogram (CV) in lithium ion containing organic electrolyte. All the films were found to show reversible electrochemical properties upon Li⁺ ion intercalation. The effects of sintering temperature on the crystallinity and consequently on the electrochemical properties of TiO₂ has been discussed.     

Synthesis of LECBD grown cluster assembled SeO2 thin films

Cluster assembled selenium oxide (SeO₂) thin films, as a function of oxygen flow pressure (OFP) have been synthesized by a low energy cluster beam deposition (LECBD) technique. The OFP dependent surface morphology leading to well separated nanoclusters (size ranging from 50 to 200 nm) and fractal features are confirmed from transmission electron microscopic (TEM) measurements. A diffusion limited aggregation (DLA) mediated fractal growth with dimension as 1.71 ± 0.01 has been observed for high OFP (60 mbar). Structural analysis by glancing angle X-ray diffraction (GXRD) and selected area diffraction (SAD) studies identify the presence of tetragonal phase SeO₂ in the deposit. Micro-Raman studies indicate the shifts in bending and stretching vibrational phonon modes in cluster assembled SeO₂ as compared to their bulk counter part due to the phonon confinement effect.     

Growth and structure of Bi0.5(Na0.7K0.2Li0.1)0.5TiO3 thin films prepared by pulsed laser deposition technique

Bi_0.5(Na_0.7K_0.2Li_0.1)_0.5TiO₃ (BNKLT) thin films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition (PLD) technique. The films prepared were examined by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The effects of the processing parameters, such as oxygen pressure, substrate temperature and laser power, on the crystal structure, surface morphology, roughness and deposition rates of the thin films were investigated. It was found that the substrate temperature of 600 °C and oxygen pressure of 30 Pa are the optimized technical parameters for the growth of textured film, and all the thin films prepared have granular structure, homogeneous grain size and smooth surfaces.     

Deposition and characterization of La2Ti2O7 thin films via spray pyrolysis process

Thin films of La₂Ti₂O₇ have been deposited on fused silica and Si substrates by a spray pyrolysis method using ethylene glycol solution of La(III)-Ti(IV)-citrate complexes as starting material and O₂ as a carrier gas. The composition, crystal structure and morphology of the films are studied.     

Microstructure of epitaxial SrRuO3 thin films on MgO substrates

SrRuO₃ thin films have been grown on singular (1 0 0) MgO substrates using pulsed laser deposition (PLD) in 30 Pa oxygen ambient and at a temperature of 400-700 °C. Ex situ reflection high-energy electron diffraction (RHEED) as well as X-ray diffraction (XRD) θ/2θ scan indicated that the films deposited above 650 °C were well crystallized though they had a rough surface as shown by atom force microscopy (AFM). XRD Φ scans revealed that these films were composed of all three different types of orientation domains, which was further confirmed by the RHEED patterns. The heteroepitaxial relationship between SrRuO₃ and MgO was found to be [1 1 0] SRO//[1 0 0] MgO and 45°-rotated cube-on-cube [0 0 1] SRO//[1 0 0] MgO. These domain structures and surface morphology are similar to that of ever-reported SrRuO₃ thin films deposited on the (0 0 1) LaAlO₃ substrates, and different from those deposited on (0 0 1) SrTiO₃ substrates that have an atomically flat surface and are composed of only the [1 1 0]-type domains. The reason for this difference was ascribed to the effect of lattice mismatch across the film/substrate interface. The room temperature resistivity of SrRuO₃ films fabricated at 700 °C was 300 μΩ cm. Therefore, epitaxial SrRuO₃ films on MgO substrate could serve as a promising candidate of electrode materials for the fabrication of ferroelectric or dielectric films.     

Structural and surface properties of Si1−xGex thin films obtained by reduced pressure CVD

This paper investigates the structure and surface characteristics, and electrical properties of the polycrystalline silicon-germanium (poly-Si_1−xGe_x) alloy thin films, deposited by vertical reduced pressure CVD (RPCVD) in the temperature range between 500 and 750 °C and a total pressure of 5 or 10 Torr. The samples exhibited a very uniform good quality films formation, with smooth surface with rms roughness as low as 7 nm for all temperature range, Ge mole fraction up to 32% (at 600 °C), textures of 〈2 2 0〉 preferred orientation at lower temperatures and strong 〈1 1 1〉 at 750 °C, for both 5 and 10 Torr deposition pressures. The ³¹P⁺ and ¹¹B⁺ doped poly-Si_1−xGe_x films exhibited always lower electrical resistivity values in comparison to similar poly-Si films, regardless of the employed anneal temperature or implantat dose. The results indicated also that poly-Si_1−xGe_x films require much lower temperature and ion implant dose than poly-Si to achieve the same film resistivity. These characteristics indicate a high quality of obtained poly-Si_1−xGe_x films, suitable as a gate electrode material for submicron CMOS devices.     

Optical parameters in SnO2 nanocrystalline textured films grown on p-InSb (111) substrates

Spectroscopic ellipsometry and photoluminescence (PL) measurements on SnO₂ nanocrystalline textured films grown on p-InSb (111) substrates by using radio-frequency magnetron sputtering at low temperature were carried out to investigate the dependence of the optical parameters on the SnO₂ thin film thickness. As the SnO₂ film thickness increases, while the energy gap of the SnO₂ film decreases, its refractive index increases. The PL spectra show that the broad peaks corresponding to the donor-acceptor pair transitions are dominant and that the peak positions change with the SnO₂ film thickness. These results can help improve understanding for the application of SnO₂ nanocrystalline thin films grown on p-InSb (111) substrates in potential optoelectronic devices based on InSb substrates.     

Optical characterization of PLD grown nitrogen-doped TiO2 thin films

Nitrogen-doped TiO₂ thin films were prepared by pulsed laser deposition (PLD) by ablating metallic Ti target with pulses of 248 nm wavelength in reactive atmospheres of O₂/N₂ gas mixtures. The layers were characterized by UV-VIS spectrophotometry and variable angle spectroscopic ellipsometry with complementary profilometry for measuring the thickness of the films. Band gap and extinction coefficient values are presented for films deposited at different substrate temperatures and for varied N₂ content of the gas mixture. The shown tendencies are correlated to nitrogen incorporation into the TiO_2-xN_x layers. It is shown that layers of significantly increased visible extinction coefficient with band gap energy as low as 2.89 eV can be obtained. A method is also presented how the spectroscopic ellipsometric data should be evaluated in order to result reliable band gap values.     

Crystallization and surface morphology evolution of erbium fluoride films on different substrates

Erbium fluoride (ErF₃) films were thermally deposited on Ge(1 1 1), Si(0 0 1) and copper mesh grid with different substrate temperature. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the structure and morphology of the films. The structure of ErF₃ films deposited on germanium and silicon changed from amorphous to crystalline with increasing the substrate temperature, while the crystallization temperature of the films on silicon is higher than that of on germanium. The infrared optical properties of the films change greatly with the evolution of crystal structure. It is also found that the morphology of ErF₃ film on Ge(1 1 1) at 200 °C is modulated by the stress between the substrate and film. The SEM and TEM results confirmed that the ErF₃ films on copper mesh grid were crystalline even at 100 °C. Interestingly, the ErF₃ films show flower-like surface morphology when deposited on copper mesh at 200 °C. The crystallization temperature (T_c) of ErF₃ films on the three substrates has the relation which is which is induced by the wetting angle of ErF₃ films on different substrates.     

Surface partition of ion energy during the growth of TiNx thin films

A simple evaluation of ion-deposited energy during surface displacement of adatoms has been presented for physical vapor deposition technology using an appropriate interaction model. The rf reactive magnetron sputtering deposition of titanium nitride (TiN_x) thin films was taken as evidence supporting the theoretical calculation. The evolution of crystallite morphology dependent on bias (or input power) illustrates that surface and subsurface microstructure of growing films can be optimized by increasing the mobility of adatoms through ion-assistance.     

Effect of growth temperature on the morphology and bonded states of SnO2 nanobaskets

The nanobaskets of SnO₂ were grown on in-house fabricated anodized aluminum oxide pores of 80 nm diameter using plasma enhanced chemical vapor deposition at an RF power of 60 W. Hydrated stannic chloride was used as a precursor and O₂ (20 sccm) as a reactant gas. The deposition was carried out from 350 to 500 °C at a pressure of 0.2 Torr for 15 min each. Deposition at 450 °C results in highly crystalline film with basket like (nanosized) structure. Further increase in the growth temperature (500 °C) results in the deterioration of the basket like structure and collapse of the alumina pores. The grown film is of tetragonal rutile structure grown along the [1 1 0] direction. The change in the film composition and bonded states with growth temperature was evident by the changes in the photoelectron peak intensities of the various constituents. In case of the film grown at 450 °C, Sn 3d_5/2 is found built up of Sn⁴⁺ and O-Sn⁴⁺ and the peaks corresponding to Sn²⁺ and O-Sn²⁺ were not detected.     

Characteristics of Si-doped Sb2Te3 thin films for phase-change random access memory

The characteristics of Si-doped Sb₂Te₃ thin films were investigated using differential scanning calorimetry (DSC), four-point probe technique, X-ray diffraction (XRD) analysis and high resolution transmission electron microscopy (HRTEM). It is found that the as-deposited Sb₂Te₃ film in our study is partly crystallized. Silicon doping increases the crystallization temperature and resistivity of Sb₂Te₃ film significantly. XRD and HRTEM analyses indicated that some of the doped Si atoms substitute for Sb or Te in the lattice, while others exists at the grain boundaries in the form of amorphous phase, which may be responsible for grain size reduction and high crystalline resistivity of Si-doped specimens. Compared with the conventional Ge₂Sb₂Te₅ film, Si-doped Sb₂Te₃ films exhibit lower melting temperature and higher crystalline resistivity, which is beneficial to RESET current reduction of phase-change random access memory (PRAM). These results show the feasibility of Si-doped Sb₂Te₃ films in PRAM application.     

Size effect in optical spectra of microcrystalline diamond powders and CVD films

Received: 24 March 1997/Accepted: 27 May 1997     

Epitaxial growth La0.67Ca0.33MnO3 thin film by radio frequency sputtering method

Perfect epitaxial growth of La_0.67Ca_0.33MnO₃ (LCMO) thin film has been achieved on (1 0 0) LaAlO₃ (LAO) single crystal substrate by radio frequency sputtering method. X-ray diffraction (XRD) and electron diffraction analysis indicates that La_0.67Ca_0.33MnO₃ film grows epitaxially on LaAlO₃ along [1 0 0] direction of the substrate. The resistivity variation with temperature of the film shows a sharp metal to semiconductor transition peak around 253 K, which is close to that of the target. The magnetoresistance (MR) also reveals high quality epitaxy film characteristic at low temperatures and near the metal to semiconductor transition temperature.     

Structural properties of CuInSe2 films prepared by selenization of metallic precursors on MoNx film substrates

The aim of this work was to study the effect of MoN_x film substrates on the structural properties of CuInSe₂ films prepared by selenization of metallic Cu-In alloy precursors. MoN_x films were prepared by reactive dc-magnetron sputtering. All the CuInSe₂ films exhibit single phase chalcopyrite structure with (1 1 2) preferred orientation, which can be explained by the reduction of lattice mismatch between CuInSe₂ and MoN_x. The bulk composition of selenized CuInSe₂ films are near stoichiometric, but the surface composition analysis suggests Cu deficiency on surface area. Furthermore, ordered defect compound, CuIn₂Se_3.5 is found on the surface of CuInSe₂ films. The results will be helpful for fabricating Cd-free ZnO buffer layer CuInSe₂ and Cu(In_1−xGa_x)Se₂ based thin film solar cells.