Structural characterization of AlN films synthesized by pulsed laser deposition

We obtained AlN thin films by pulsed laser deposition (PLD) from a polycrystalline AlN target using a pulsed KrF* excimer laser source (248 nm, 25 ns, intensity of ∼4 × 10⁸ W/cm², repetition rate 3 Hz, 10 J/cm² laser fluence). The target-Si substrate distance was 5 cm. Films were grown either in vacuum (10⁻⁴ Pa residual pressure) or in nitrogen at a dynamic pressure of 0.1 and 10 Pa, using a total of 20,000 subsequent pulses. The films structure was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and spectral ellipsometry (SE). Our TEM and XRD studies showed a strong dependence of the film structure on the nitrogen content in the ambient gas. The films deposited in vacuum exhibited a high quality polycrystalline structure with a hexagonal phase. The crystallite growth proceeds along the c-axis, perpendicular to the substrate surface, resulting in a columnar and strongly textured structure. The films grown at low nitrogen pressure (0.1 Pa) were amorphous as seen by TEM and XRD, but SE data analysis revealed ∼1.7 vol.% crystallites embedded in the amorphous AlN matrix. Increasing the nitrogen pressure to 10 Pa promotes the formation of cubic (≤10 nm) crystallites as seen by TEM but their density was still low to be detected by XRD. SE data analysis confirmed the results obtained from the TEM and XRD observations.     

Pulsed laser deposition of doped skutterudite thin films

Ca_xCo₄Sb₁₂ skutterudite thin films have been prepared by pulsed laser deposition using a Nd:YAG laser working at 532 or 266 nm of wavelength. Characterization has been carried out by X-ray diffraction, atomic force microscopy and scanning electron microscopy. Emphasis has been put on the difficulty to obtain the skutterudite phase. Influence of the deposition temperature, the way of sticking the substrate, the laser fluence, the base pressure prior to deposition and the laser wavelength has been studied. All parameters revealed to have a drastic effect, and the skutterudite could only be achieved in a very narrow range of temperature and laser fluence, for a given wavelength, showing the importance on how these parameters are measured to ensure reproducible results.     

Doped thin metal oxide films for catalytic gas sensors

TiO₂ and Pt doped TiO₂ thin films were grown by pulsed laser deposition on 〈0 0 1〉 SiO₂ substrates. The doped films were compared with undoped ones deposited in similar experimental conditions. An UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser was used for the irradiation of the TiO₂ or Pt doped TiO₂ targets. The substrate temperatures were fixed during the growth of the thin films at values within the 300-500 °C range. The films’ surface morphology was investigated by atomic force microscopy and their crystalline quality by X-ray diffractometry. The corresponding transmission spectra were recorded with the aid of a double beam spectrophotometer in the spectral range of 400-1100 nm. No contaminants or Pt segregation were detected in the synthesized anatase phase TiO₂ thin films composition. Titania crystallites growth inhibition was observed with the increase of the dopant concentration. The average optical transmittance in the visible-infrared spectral range of the films is higher than 85%, which makes them suitable for sensor applications.     

Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.     

Investigation of transmittance property of Palladium thin films fabricated by pulsed laser deposition with polarization using single layer model

In this paper the structure, morphology and optical properties of Pd thin films deposited on glass substrate by pulse laser deposition technique at two different substrate temperatures have been investigated. The fabricated films were characterized by various methods such as XRD, AFM, and UV-vis-NIR spectroscopy. The influence of surface roughness and angle of incidence with p polarization was investigated experimentally by optical property of palladium (Pd) thin films of two different thicknesses and rms roughness from transmission measurement in the visible spectral range. It has been shown that the experimental transmittance spectra agree well with their theoretical values for absorbing Pd thin film. The transmittance of thin film increases with increase in incident angle for the same sample.     

Cobalt and tantalum additions for enhanced electrochromic performances of nickel-based oxide thin films grown by pulsed laser deposition

Aiming at improving the durability of anodic electrochromic nickel oxide thin films, Ni-M-O (M = Co, Ta) thin films were grown by pulsed laser deposition (PLD), using optimized conditions, namely room temperature and 10⁻¹ mbar oxygen pressure. For low Co and Ta contents (<5%), both additions lead to a loss of the [1 1 1] preferred orientation of the NiO rock-salt structure followed by a film amorphization with increasing Ta amount. Among the two series of metal additions (M ≤ 20%), the Ni-Co-O (5% Co) and Ni-Ta-O (10% Ta) thin films show the highest electrochemical performances especially in respect of improved durability. If the enhanced properties are associated with a limited dissolution of the oxidized phase for the Ni-Ta-O system, the opposite trend is observed for the Ni-Co-O system as compared to pure NiO.     

Competing magnetoresistance contributions in sputtered FePt thin films

Fe-Pt thin films were deposited by rf sputtering on an MgO substrate heated at different temperatures to induce the formation of the perpendicular Fe-Pt L1₀ phase with a different grain morphology on the nanometer scale. All films are characterized by a mazelike pattern of FePt nanograins with interconnected bases. MFM images and magnetization curves indicate that all samples have a strong perpendicular magnetic anisotropy arising from (0 0 1) growth. The temperature behaviour of the electrical resistance indicates that a percolating path exists for conduction electrons in the mazelike pattern. The magnetoresistance was measured as a function of magnetic field (applied longitudinally) and temperature in the ranges −70 kOe<H<+70 kOe and 4 K<T<150 K, respectively. All samples display a complex behaviour of the electrical resistance as a function of applied field. The role of the different magnetoresistance effects (both intrinsic and extrinsic) measured in these FePt thin films is elucidated.     

Effect of annealing on thermal stability and morphology of pulsed laser deposited Ir thin films

Iridium (Ir) thin films, deposited on Si (1 0 0) substrate by pulsed laser deposition (PLD) technique using Ir target in a vacuum atmosphere, were annealed in air ambient and the thermal stability was investigated. The crystal structure and surface morphology of Ir thin films before and after being annealed were studied by X-ray diffraction, Raman scattering, scanning electron microscope, and atomic force microscopy. The results showed that single-phase Ir thin films with (1 1 1) preferred orientation could be deposited on Si (1 0 0) substrate at 300 °C and it remained stable below 600 °C, which showed a promising bottom electrode of integrated ferroelectric capacitors. Ir thin films got oxidized to IrO₂ at temperatures from 650 to 800 °C.     

Preparation and characterizations of amorphous nanostructured SiC thin films by low energy pulsed laser deposition

Amorphous silicon carbide (SiC) thin films were deposited on silicon substrates by pulsed laser ablation at room temperature. Thicknesses and surface morphology of the thin films were characterized using optical profilers, atomic force and field emission scanning electron microscopy. Nanohardnes, modulus and scratch resistance properties were determined using XP nanoindenter. The results show that crack free, smooth and nanostructured thin films can be deposited using low laser energy densities.     

Morphological and optical properties of silicon thin films by PLD

Silicon thin films have been prepared on sapphire substrates by pulsed laser deposition (PLD) technique. The films were deposited in vacuum from a silicon target at a base pressure of 10⁻⁶ mbar in the temperature range from 400 to 800 °C. A Q-switched Nd:YAG laser (1064 nm, 5 ns duration, 10 Hz) at a constant energy density of 2 J × cm⁻² has been used. The influence of the substrate temperature on the structural, morphological and optical properties of the Si thin films was investigated.Spectral ellipsometry and atomic force microscopy (AFM) were used to study the thickness and the surface roughness of the deposited films. Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased deposition temperature.     

Structural study of TiO2 thin films by micro-Raman spectroscopy

The Raman spectroscopy method was used for structural characterization of TiO₂ thin films prepared by atomic layer deposition (ALD) and pulsed laser deposition (PLD) on fused silica and single-crystal silicon and sapphire substrates. Using ALD, anatase thin films were grown on silica and silicon substrates at temperatures 125–425 °C. At higher deposition temperatures, mixed anatase and rutile phases grew on these substrates. Post-growth annealing resulted in anatase-to-rutile phase transitions at 750 °C in the case of pure anatase films. The films that contained chlorine residues and were amorphous in their as-grown stage transformed into anatase phase at 400 °C and retained this phase even after annealing at 900 °C. On single crystal sapphire substrates, phase-pure rutile films were obtained by ALD at 425 °C and higher temperatures without additional annealing. Thin films that predominantly contained brookite phase were grown by PLD on silica substrates using rutile as a starting material.     

Nanocomposite oxide thin films grown by pulsed energy beam deposition

Highly non-stoichiometric indium tin oxide (ITO) thin films were grown by pulsed energy beam deposition (pulsed laser deposition-PLD and pulsed electron beam deposition-PED) under low oxygen pressure. The analysis of the structure and electrical transport properties showed that ITO films with a large oxygen deficiency (more than 20%) are nanocomposite films with metallic (In, Sn) clusters embedded in a stoichiometric and crystalline oxide matrix. The presence of the metallic clusters induces specific transport properties, i.e. a metallic conductivity via percolation with a superconducting transition at low temperature (about 6 K) and the melting and freezing of the In-Sn clusters in the room temperature to 450 K range evidenced by large changes in resistivity and a hysteresis cycle. By controlling the oxygen deficiency and temperature during the growth, the transport and optical properties of the nanocomposite oxide films could be tuned from metallic-like to insulating and from transparent to absorbing films.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Characterization of pulsed laser deposited chalcogenide thin layers

In this work we report on pulsed laser deposition (PLD) of chalcogenide thin films from the systems (AsSe)_100−xAgI_x and (AsSe)_100−xAg_x for sensing applications. A KrF* excimer laser (λ = 248 nm; τ_FWHM = 25 ns) was used to ablate the targets that had been prepared from the synthesised chalcogenide materials. The films were deposited in either vacuum (4 × 10⁻⁴ Pa) or argon (5 Pa) on silicon and glass substrates kept at room temperature. The basic properties of the films, including their morphology, topography, structure, and composition were characterised by complementary techniques. Investigations by X-ray diffraction (XRD) confirmed the amorphous nature of the films, as no strong diffraction reflections were found. The film composition was studied by energy dispersive X-ray (EDX) spectroscopy. The morphology of the films investigated by scanning electron microscopy (SEM), revealed a particulate-covered homogeneous surface, typical of PLD. Topographical analyses by atomic force microscopy (AFM) showed that the particulate size was slightly larger in Ar than in vacuum. The uniform surface areas were rather smooth, with root mean square (rms) roughness increasing up to several nanometers with the AgI or Ag doping. Based upon the results from the comprehensive investigation of the basic properties of the chalcogenide films prepared by PLD and their dependence on the process parameters, samples with appropriate sorption properties can be selected for possible applications in cantilever gas sensors.     

Pulsed laser deposition and its current research status in preparing hydroxyapatite thin films

Pulsed laser deposition (PLD) is a conceptually and experimentally simple yet highly versatile tool for thin films and multi-layer film research. The mechanisms, advantages and disadvantages of pulsed laser deposition were reviewed. The process and some methods to resolve the drawbacks of PLD were discussed. Pulsed laser deposition of hydroxyapatite thin films was reviewed. Simple adjustment of PLD parameters can deposit hydroxyapatite in situ in crystalline form, amorphous films or HA with other calcium phosphate phases. Compared with plasma sprayed HA coatings the pulsed laser deposition HA thin films have higher coating/substrate adhesion and have minor undesirable phases under optimal conditions. Finally, we suggested some new researches should be done.     

Structural and optical properties of pulsed laser deposited SrBi2Nb2O9 thin films

SrBi₂Nb₂O₉ (SBN) thin films were prepared on fused quartz substrates at room temperature by pulsed laser deposition. The influence of deposition parameters such as target-to-substrate distance, oxygen pressure and annealing temperature on film crystallization behavior was investigated by X-ray diffraction. Results indicated that the films grown at the optimum processing conditions have polycrystalline structure with a single layered perovskite phase. The optical transmittance of the films prepared at various oxygen pressures was measured in the wavelength range 200–900 nm using UV–vis spectrophotometer. The results showed that there is a red shift in the optical absorption edge with a rise in the oxygen pressure. Refractive index as a function of wavelength and optical band gap of the films were determined from the optical transmittance spectra. The results indicated that the refractive index increases with increasing oxygen pressure at the same incident light wavelength, while the band gap reduces from 4.13 to 3.88 eV. It may be attributed to an increase in packing density and grain size, and decrease in oxygen defects.     

Morphology, magnetic, magnetoresistance and optical properties of Co-Ni-Mo alloys thin films

We present in this paper several results concerning the preparation by means of electrolysis and characterization of Co-Ni-Mo thin films. Co-Ni-Mo thin films with different molybdenum content in the range 0-25 at% Mo were prepared from a complex solution containing ions of Co, Ni and Mo, using galvanostatic control, on aluminum substrates. The effects of applied current density on the morphology, magnetic, magnetoresistance, and optical properties of the electrodeposited Co-Ni-Mo films were investigated. The applied current density significantly influenced the film composition and their magnetic properties. The increase of molybdenum content in Co-Ni films (up to 25 at% Mo) enhances the resistivity, but it reduces the magnetoresistance effect. We report the first observation of magnetoresistance as high as 8% in Co-Ni-Mo thin films.     

Role of vanadium content in ZnO thin films grown by pulsed laser deposition

Vanadium-doped ZnO films (Zn_1−xV_xO, where x = 0.02, 0.03, 0.05 and 0.07), were formed from ceramic targets on c-cut sapphire substrates using pulsed laser deposition at substrate temperature of 600 °C and oxygen pressure of 10 Pa. In order to clarify how the vanadium concentration influences the films’ properties, structural and magnetic investigations were performed. All films crystallised in wurtzite phase and presented a c-axis preferred orientation at low concentrations of vanadium. The results implied that the doping concentration and crystalline microstructure influence strongly the system's magnetic characteristics. Weak ferromagnetism was registered for the film with the lowest doping concentration (2 at.%), which exhibited a ferromagnetic behavior at Curie temperature higher than 300 K. Increasing the vanadium content in the film caused degradation of the magnetic ordering.     

Quenching of surface traps in Mn doped ZnO thin films for enhanced optical transparency

The structural and photoluminescence analyses were performed on un-doped and Mn doped ZnO thin films grown on Si (1 0 0) substrate by pulsed laser deposition (PLD) and annealed at different post-deposition temperatures (500-800 °C). X-ray diffraction (XRD), employed to study the structural properties, showed an improved crystallinity at elevated temperatures with a consistent decrease in the lattice parameter ‘c’. The peak broadening in XRD spectra and the presence of Mn 2p3/2 peak at ∼640 eV in X-ray Photoelectron Spectroscopic (XPS) spectra of the doped thin films confirmed the successful incorporation of Mn in ZnO host matrix. Extended near band edge emission (NBE) spectra indicated the reduction in the concentration of the intrinsic surface traps in comparison to the doped ones resulting in improved optical transparency. Reduced deep level emission (DLE) spectra in doped thin films with declined PL ratio validated the quenching of the intrinsic surface traps thereby improving the optical transparency and the band gap, essential for optoelectronic and spintronic applications. Furthermore, the formation and uniform distribution of nano-sized grains with improved surface features of Mn-doped ZnO thin films were observed in Field Emission Scanning Electron Microscopy (FESEM) images.