Accelerated life ac conductivity measurements of CRT oxide cathodes

The ac conductivity measurements have been carried out for the activated Ba/SrO cathode with additional 5% Ni powder for every 100 h acceleration life time at the temperature around 1125 K. The ac conductivity was studied as a function of temperature in the range 300-1200 K after conversion and activation of the cathode at 1200 K for 1 h in two cathodes face to face closed configuration. The experimental results prove that the hopping conductivity dominate in the temperature range 625-770 K through the traps of the WO₃ associate with activation energy E_a = 0.87 eV, whereas from 500-625 K it is most likely to be through the traps of the Al₂O₃ with activation energy of E_a = 1.05 eV. The hopping conductivity at the low temperature range 300-500 K is based on Ni powder link with some Ba contaminants in the oxide layer stricture which indicates very low activation energy E_a = 0.06 eV.     

Laser synthesis of nanostructures based on transition metal oxides

Nanostructures based on iron oxides in the form of thin films were synthesized while laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors (Fe(CO)₅) under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface with power density about 10² W/cm² and vapor pressure 666 Pa. Analysis of surface morphology and relief of the deposited films was carried out with scanning electron microscopy (SEM) and atomic force microscopy (AFM). This analysis demonstrated their cluster structure with average size no more than 100 nm. It was found out that the thicker the deposited film, the larger sizes of clusters with more oxides of higher oxidized phases were formed. The film thickness (d) was 10 and 28 nm. The deposited films exhibited semiconductor properties in the range 170-340 K which were stipulated by oxide content with different oxidized phases. The width of the band gap E_g depends on oxide content in the deposited film and was varied in the range 0.30-0.64 eV at an electrical field of 1.6 × 10³ V/m. The band gap E_g was varied in the range 0.46-0.58 eV at an electrical field of 45 V/m. The band gap which is stipulated by impurities in iron oxides E_i was varied in the range 0.009-0.026 eV at an electrical field of 1.6 × 10³ V/m and was varied in the range 0-0.16 eV at an electrical field 45 V/m. These narrow band gap semiconductor thin films displayed of the quantum dimensional effect.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Native oxidation of ultra high purity Cu bulk and thin films

The effect of microstructure and purity on the native oxidation of Cu was studied by using angle-resolved X-ray photoelectron spectroscopy (AR-XPS) and spectroscopic ellipsometry (SE). A high quality copper film prepared by ion beam deposition under a substrate bias voltage of −50 V (IBD Cu film at V_s = −50 V) showed an oxidation resistance as high as an ultra high purity copper (UHP Cu) bulk, whereas a Cu film deposited without substrate bias voltage (IBD Cu film at V_s = 0 V) showed lower oxidation resistance. The growth of Cu₂O layer on the UHP Cu bulk and both types of the films obeyed in principle a logarithmic rate law. However, the growth of oxide layer on the IBD Cu films at V_s = 0 and −50 V deviated upward from the logarithmic rate law after the exposure time of 320 and 800 h, respectively. The deviation from the logarithmic law is due to the formation of CuO on the Cu₂O layer after a critical time.     

Influence of sputter-etching of substrate on the microstructural and optical properties of ZnO films deposited by RF magnetron sputtering

ZnO films were prepared using radio frequency magnetron sputtering on Si(1 1 1) substrates that were sputter-etched for different times ranging from 10 to 30 min. As the sputter-etching time of the substrate increases, both the size of ZnO grains and the root-mean-square (RMS) roughness decrease while the thickness of the ZnO films shows no obvious change. Meanwhile, the crystallinity and c-axis orientation are improved by increasing the sputter-etching time of the substrate. The major peaks at 99 and 438 cm⁻¹ are observed in Raman spectra of all prepared films and are identified as E₂(low) and E₂(high) modes, respectively. The Raman peak at 583 cm⁻¹ appears only in the films whose substrates were sputter-etched for 20 min and is assigned to E₁(LO) mode. Typical ZnO infrared vibration peak located at 410 cm⁻¹ is found in all FTIR spectra and is attributed to E₁(TO) phonon mode. The shoulder at about 382 cm⁻¹ appearing in the films whose substrates were sputter-etched for shorter time (10-20 min) originates from A₁(TO) phonon mode. The results of photoluminescence (PL) spectra reveal that the optical band gap (Eg) of the ZnO films increases from 3.10 eV to 3.23 eV with the increase of the sputter-etching time of the substrate.     

Annealing effect on CdS/SnO2 films grown by chemical bath deposition

The extensive investigation of the annealing effect in nitrogen atmosphere on the structural optical and electrical properties of chemically deposited CdS films on SnO₂ has been performed. The as-deposited film shows 2.45 eV band gap (E_g) and decreases with increasing annealing temperature. The film annealed at 623 K having pure hexagonal phase (a = 4.14 Å, c = 6.71 Å for [1 0 0] plane) and E_g = 2.36 eV shows 10 times higher conductivity for all temperature range, and shows two different activation energies E_a = 0.114 eV and E_a = 0.033 eV for the temperature range 395 K ≤ T ≤ 515 K and 515 K ≤ T ≤ 585 K, respectively. The structural parameters such as dislocation density, strain and optical parameters such as absorption and extinction coefficient are calculated and compared for all the films.     

The influence of light intensity on surface recombination in GaS single crystals

Gallium sulphide (GaS) is a layer structure semiconductor with relatively wide energy gap (E_g (295 K) = 2.5 eV and E_g (80 K) = 2.62 eV). It has potential applications in some areas of optoelectronics. This paper presents the investigations of the influence of light intensity on surface recombination velocity of charge carriers in GaS single crystals. To attain this purpose spectral dependences (between 420 and 550 nm) of absorption coefficients, reflectivity coefficients and photoconductivity were measured in vacuum. The investigations were performed for various light intensities in several temperatures from 80 to 333 K. The least square method was applied to fit the theoretical dependences of photoconductivity on wavelength and intensity of illumination at these temperatures. From the fittings the temperature and light intensity dependences of surface recombination velocity and bulk lifetime of charge carriers were obtained.     

On ultra-thin oxide/Si and very-thin oxide/Si structures prepared by wet chemical process

The properties of ultra-thin oxide/Si and very-thin oxide/Si structures prepared by wet chemical oxidation in nitric acid aqueous solutions (NAOS) and passivated in HCN aqueous solutions were investigated by electrical, optical and structural methods. n- and p-doped (1 0 0) crystalline Si substrates were used. There were identified more types of interface defect states in dependence on both post-oxidation treatment and passivation procedure. On samples prepared on n-type Si, continuous spectrum of defect states of 0.05-0.2 eV range and discrete defect traps, ∼E_CB − 0.26 eV and ∼E_CB − 0.39 eV, were found. All mentioned defects are related with various types of Si dangling bonds and/or with SiO_x precipitates. Post-metallization annealing of investigated MOS structures reduced the interface defect density and suppressed the leakage currents. It did not change spectral profile of interface defect states in the Si band gap. In addition, there are presented following two optical phenomena: relation between amplitude of photoluminescence signal of NAOS samples and parameters of chemical oxidation process and quantum confinement effect observed on samples containing Si grains of size less as ∼2 nm.     

Physical properties of ZnO thin films deposited by spray pyrolysis technique

Thin films of ZnO have been prepared on glass substrates at different thicknesses by spray pyrolysis technique using 0.2 M aqueous solution of zinc acetate. X-ray diffraction reveals that the films are polycrystalline in nature having hexagonal wurtzite type crystal structure. The resistivity at room temperature is of the order 10⁻² Ω cm and decreased as the temperature increased. Films are highly transparent in the visible region. The dependence of the refractive index, n, and extinction coefficient, k, on the wavelength for a sprayed film is also reported. Optical bandgap, E_g, has been reported for the films. A shift from E_g = 3.21 eV to 3.31 eV has been observed for deposited films.     

Effects of rf power on surface-morphological, structural and electrical properties of aluminium-doped zinc oxide films by magnetron sputtering

Aluminium-doped zinc oxide (ZnO:Al) films were prepared by magnetron sputtering at different radio-frequency powers (P_rf) of 50, 100, 150 and 200 W. The properties of the films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), Raman microscopy, and spectrophotometry with the emphasis on the evolution of compositional, surface-morphological, optical, electrical and microstructural properties. XPS spectra showed that within the detection limit the films are chemically identical to near-stoichiometric ZnO. AFM revealed that root-mean-square roughness of the films has almost linear increase with increasing P_rf. Optical band gap E_gopt of the films increases from 3.31 to 3.51 eV when P_rf increases from 50 to 200 W. A widening E_gopt of the ZnO:Al films compared to the band gap (∼3.29 eV) of undoped ZnO films is attributed to a net result of the competition between the Burstein-Moss effect and many-body effects. An electron concentration in the films was calculated in the range of 3.73 × 10¹⁹ to 2.12 × 10²⁰ cm⁻³. Raman spectroscopy analysis indicated that well-identified peaks appear at around 439 cm⁻¹ for all samples, corresponding to the band characteristics of the wurtzite phase. Raman peaks in the range 573-579 cm⁻¹ are also observed, corresponding to the A₁ (LO) mode of ZnO.     

Laser-assisted synthesis of semiconductor chromium disilicide films

Different photo-assisted techniques were employed for chromium disilicide (CrSi₂) semiconductor film fabrication. Flash evaporation of CrSi₂ powder on the Si substrate heated to ∼740 K leads to the formation (according to XRD study) of amorphous films. Post-annealing at 920 K leads to the formation of polycrystalline CrSi₂ phase. Crystallization is improved by further annealing with 1500 Q-Switched Nd:YAG laser pulses. Optical properties of the as deposited and annealed CrSi₂ films have been investigated in the 240-1100 nm spectral range by using spectroscopic ellipsometry. The formation of CrSi₂ semiconductor phase was additionally confirmed by the temperature dependence of electrical resistance of the films treated by Q-switched Nd:YAG laser. The band gap for intrinsic conductivity results E_g ≅ 0.2 eV. Backward laser-induced film transfer (LIFT) was also used for CrSi₂ film deposition from bulk material on Si substrates. Pulsed CO₂ laser was employed for this purpose, because of transparency of silicon at the 10.6 μm wavelength. Measurements of the electrical resistance of the deposited films as a function of temperature showed their semiconductor behavior (E_g = 6 × 10⁻⁴ eV). Chromium disilicide films were also deposited by congruent pulsed laser ablation deposition on Si substrates either at room temperature or heated to about 740 K. In this last case the deposit exhibits semiconducting properties with E_g ≅ 0.18 eV.     

Synthesis and characterization of Zn(O,OH)S and AgInS2 layers to be used in thin film solar cells

In this paper AgInS₂ and Zn(O,OH)S thin films were synthesized and characterized. AgInS₂ layers were grown by co-evaporation from metal precursors in a two-step process, and, Zn(O,OH)S thin films were deposited from chemical bath containing thiourea, zinc acetate, sodium citrate and ammonia. X-ray diffraction measurements indicated that AgInS₂ thin films grown with chalcopyrite structure, and the as-grown Zn(O,OH)S thin films were polycrystalline. It was also found that the AgInS₂ films presented p-type conductivity, a high absorption coefficient (greater than 10⁴ cm⁻¹) and energy band-gap E_g of about 1.95 eV, Zn(O,OH),S thin films presented E_g of about 3.89 eV. Morphological analysis showed that under this synthesis conditions Zn(O,OH),S thin films coated uniformly the absorber layer. Additionally, the Zn(O,OH)S kinetic growth on AgInS₂ layer was studied also. Finally, the results suggest that these layers possibly could be used in one-junction solar cells and/or as top cell in a tandem solar cell.     

Fabrication and characterization of La-doped HfO2 gate dielectrics by metal-organic chemical vapor deposition

La-doped HfO₂ gate dielectric thin films have been deposited on Si substrates using La(acac)₃ and Hf(acac)₄ (acac = 2,4-pentanedionate) mixing sources by low-pressure metal-organic chemical vapor deposition (MOCVD). The structure, thermal stability, and electrical properties of La-doped HfO₂ films have been investigated. Inductive coupled plasma analyses confirm that the La content ranging from 1 to 5 mol% is involved in the films. The films show smaller roughness of ∼0.5 nm and improved thermal stability up to 750 °C. The La-doped HfO₂ films on Pt-coated Si and fused quartz substrates have an intrinsic dielectric constant of ∼28 at 1 MHz and a band gap of 5.6 eV, respectively. X-ray photoelectron spectroscopy analyses reveal that the interfacial layer is Hf-based silicate. The reliable value of equivalent oxide thickness (EOT) around 1.2 nm has been obtained, but with a large leakage current density of 3 A/cm² at V_g = 1V + V_fb. MOCVD-derived La-doped HfO₂ is demonstrated to be a potential high-k gate dielectric film for next generation metal oxide semiconductor field effect transistor applications.     

Characterization of oxide layers formed on electrochemically treated Ti by using soft X-ray absorption measurements

The oxide layers of electrolytic oxidized titanium (Ti) were characterized using Ti L_2,3 and O K edge X-ray absorption. The spectra show that the structure of the oxide layers that are formed during a 1 min treatment are dependent on the concentration of the electrolyte (H₂SO₄ or Na₂SO₄) with which the Ti surface was treated, and also on the magnitude of the potential that was applied during the anodic oxidation process (100 V or 150 V). It is found that a potential of 150 V and an electrolyte concentration of 0.5 M or 1.0 M produces a layer of TiO₂ having rutile crystal structure.     

Inductively coupled plasma induced deep levels in epitaxial n-GaAs

The electronic properties of defects introduced by low energy inductively coupled Ar plasma etching of n-type (Si doped) GaAs were investigated by deep level transient spectroscopy (DLTS) and Laplace DLTS. Several prominent electron traps (E_c—0.046 eV, E_c—0.186 eV, E_c—0.314 eV. E_c—0.528 eV and E_c—0.605 eV) were detected. The metastable defect E_c—0.046 eV having a trap signature similar to E1 is observed for the first time. E_c—0.314 eV and E_c—0.605 eV are metastable and appear to be similar to the M3 and M4 defects present in dc H-plasma exposed GaAs.     

Structure, band offsets and photochemistry at epitaxial α-Cr2O3/α-Fe2O3 heterojunctions

We test the hypothesis that electron-hole pair separation following light absorption enhances photochemistry at oxide/oxide heterojunctions which exhibit a type II or staggered band alignment. We have used hole-mediated photodecomposition of trimethyl acetic acid chemisorbed on surfaces of heterojunctions made from epitaxial α-Cr₂O₃ on α-Fe₂O₃(0001) to monitor the effect of UV light of wavelength 385 nm (3.2 eV) in promoting photodissociation. Absorption of photons of energies between the bandgaps of α-Cr₂O₃ (E_g = 4.8 eV) and α-Fe₂O₃ (E_g = 2.1 eV) is expected to be strong only in the α-Fe₂O₃ layer. The staggered band alignment should then promote the segregation of holes (electrons) to the α-Cr₂O₃ (α-Fe₂O₃) layer. Surprisingly, we find that the α-Cr₂O₃ surface alone promotes photodissociation of the molecule at hν = 3.2 eV, and that any effect of the staggered band alignment, if present, is masked. We propose that the inherent photoactivity of the α-Cr₂O₃(0001) surface results from the creation of bound excitons in the surface which destabilize the chemisorption bond in the molecule, resulting in photodecomposition.     

Photoluminescence and photoelectrochemical properties of nanocrystalline ZnO thin films synthesized by spray pyrolysis technique

A simple and inexpensive spray pyrolysis technique (SPT) was employed for the synthesis of nanocrystalline zinc oxide (ZnO) thin films onto soda lime glass and tin doped indium oxide (ITO) coated glass substrates at different substrate temperatures ranging from 300 °C to 500 °C. The synthesized films were polycrystalline, with a (0 0 2) preferential growth along c-axis. SEM micrographs revealed the uniform distribution of spherical grains of about 80-90 nm size. The films were transparent with average visible transmittance of 85% having band gap energy 3.25 eV. All the samples exhibit room temperature photoluminescence (PL). A strong ultraviolet (UV) emission at 398 nm with weak green emission centered at 520 nm confirmed the less defect density in the samples. Moreover, the samples are photoelectrochemically active and exhibit the highest photocurrent of 60 μA, a photovoltage of 280 mV and 0.23 fill factor (FF) for the Zn₄₅₀ films in 0.5 M Na₂SO₄ electrolyte, when illuminated under UV light.     

Characterization of defects introduced in Sb doped Ge by 3 keV Ar sputtering using deep level transient spectroscopy (DLTS) and Laplace-DLTS (LDLTS)

We have used deep level transient spectroscopy (DLTS), and Laplace-DLTS to investigate the defects created in antimony doped germanium (Ge) by sputtering with 3 keV Ar ions. Hole traps at E_V+0.09 eV and E_V+0.31 eV and an electron trap at E_C−0.38 eV (E-center) were observed soon after the sputtering process. Room temperature annealing of the irradiated samples over a period of a month revealed a hole trap at E_V+0.26 eV. Above room temperature annealing studies revealed new hole traps at E_V+0.27 eV, E_V+0.30 eV and E_V+0.40 eV.     

Influence of atomic hydrogen annealing on the optical properties of vacuum-deposited a-Si:H films

The influence of atomic hydrogen annealing on the optical parameters of a-Si:H films was studied using spectrophotometric measurements of the film transmittance and reflectance in the wavelength range 200-3000 nm. In this annealing, the deposition of a thin layer and treatment with atomic hydrogen were repeated alternately, where the thickness of the thin cyclic layer, d_cyc, and the treatment time of each cycle, t_ca, were kept fixed for each sample. A series of different samples with average thickness of 0.5 μm and different d_cyc and t_ca were prepared. It was found that the refractive index, n, and the optical energy gap, E_g, increase as the treatment time, t_ca, increases from 0 to 60 s, while at t_ca=120 s both n and E_g decrease. Also, both the refractive index and the optical energy gap decrease with increasing the relative diffusion length of hydrogen, √t_ca/d_cyc from 0.39 to 0.77. The widening of E_g is due to the structural relaxation resulting from impingement of atomic hydrogen on the growing surface. Thus, a good-quality a-Si:H with Urbach parameter 65 mev and optical energy gap of 1.78 eV was successfully prepared.     

Electrical and optical properties of silver doped indium oxide thin films prepared by reactive DC magnetron sputtering

Silver doped indium oxide (In_2−x Ag_x O_3−y) thin films have been prepared on glass and silicon substrates at room temperature (300 K) by reactive DC magnetron sputtering technique using an alloy target of pure indium and silver (80: 20 atomic %. The magnetron power (and hence the metal atom sputter flux) is varied in the range 40-80 W. The energy dispersive analysis of X-ray (EDAX) results show that the silver content in the film decreases with increasing magnetron power. The grain size of these films is of the order of 100 nm. The resistivity of these films is in the range 10⁻²-10⁻³ Ω cm. The work function of the silver-indium oxide films (by Kelvin Probe) are in the range: 4.64-4.55 eV. The refractive index of these films (at 632.8 nm) varies in the range: 1.141-1.195. The optical band gap of indium oxide (3.75 eV) shrinks with silver doping. Calculations of the partial ionic charge (by Sanderson's theory) show that silver doping in indium oxide thin films enhance the ionicity.