Structural and optical properties of zinc nitride films prepared by rf magnetron sputtering

Zinc nitride films were prepared on quartz substrates by rf magnetron sputtering using pure zinc target in N₂-Ar plasma. X-ray diffraction (XRD) analysis indicates that the films just after deposition are polycrystalline with a cubic structure and a preferred orientation of (4 0 0). X-ray photoelectron spectroscopy (XPS) analysis also confirms the formation of N-Zn bonds and the substitution incorporation of oxygen for nitrogen on the surface of the films. The optical band gap is calculated from the transmittance spectra of films just after deposition, and a direct band gap of 1.01 ± 0.02 eV is obtained. Room temperature PL measurement is also performed to investigate the effect of defect on the band gap and quality of the zinc nitride films.     

Novel chemical synthetic route and characterization of zinc selenide thin films

Zinc selenide (ZnSe) thin film have been deposited using chemical bath method on non-conducting glass substrate in a tartarate bath containing zinc sulfate, ammonia, hydrazine hydrate, sodium selenosulfate in an aqueous alkaline medium at 333 K. The deposition parameter of the ZnSe thin film is interpreted in the present investigation. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption, electrical measurements, atomic absorption spectroscopy (AAS). The ZnSe thin layers grown with polycrystalline zinc blende system along with some amorphous phase present in ZnSe film. The direct optical band gap ‘E_g’ for the film was found to be 2.81 eV and electrical conductivity in the order of 10⁻⁸(Ω cm)⁻¹ with n-type conduction mechanism.     

Pulsed laser ablation of zinc selenide in nitrogen ambience: Formation of zinc nitride films

Zinc nitride (Zn₃N₂) thin films are prepared using pulsed laser deposition (PLD) from zinc selenide (ZnSe) target at different nitrogen ambient pressures viz. 1, 3, 5, 7 and 10 Pa. The films prepared with nitrogen pressures 1 and 3 Pa are amorphous in nature, whereas the films prepared at 5, 7 and 10 Pa exhibit the presence of cubic bixbyite Zn₃N₂ structure with lattice parameter very close to bulk of Zn₃N₂. The particle size calculated by Debye Scherrer's formula is in the nano regime. Surface morphology of the films is studied by SEM and AFM analysis. Optical parameters such as band gap, refractive index and porosity of the films are calculated. Moreover, the present study confers an outlook about how do various factors such as substrate temperature, reactive supplementing gas and laser-target interaction influence the film developing process during pulsed lased deposition.     

Structural and optical properties of RF magnetron sputtered aluminum nitride films without external substrate heating

We report structural and optical properties of aluminum nitride (AlN) thin films prepared by RF magnetron sputtering. A ceramic AlN target was used to sputter deposit AlN films without external substrate heating in Ar-N₂ (1:1) ambient. The X-ray diffraction and high resolution transmission electron microscopy results revealed that the films were preferentially oriented along c-axis. Cross-sectional imaging revealed columnar growth perpendicular to the substrate. The secondary ion mass spectroscopy analysis confirmed that aluminum and nitrogen distribution was uniform within the thickness of the film. The optical band gap of 5.3 eV was evaluated by UV-vis spectroscopy. Photo-luminescence broad band was observed in the range of 420-600 nm with two maxima, centered at 433 nm and 466 nm wavelengths related to the energy states originated during the film growth. A structural property correlation has been carried out to explore the possible application of such important well oriented nano-structured two-dimensional semiconducting objects.     

Room temperature transparent conducting oxides based on zinc oxide thin films

Doped zinc oxide thin films are grown on glass substrate at room temperature under oxygen atmosphere, using pulsed laser deposition (PLD). O₂ pressure below 1 Pa leads to conductive films. A careful characterization of the film stoichiometry and microstructure using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) concludes on a decrease in crystallinity with Al and Ga additions (≤3%). The progressive loss of the (0 0 2) orientation is associated with a variation of the c parameter value as a function of the film thickness and substrate nature. ZnO:Al and ZnO:Ga thin films show a high optical transmittance (>80%) with an increase in band gap from 3.27 eV (pure ZnO) to 3.88 eV and 3.61 eV for Al and Ga doping, respectively. Optical carrier concentration, optical mobility and optical resistivity are deduced from simulation of the optical data.     

Structural and optical properties of nano-structured tungsten-doped ZnO thin films grown by pulsed laser deposition

Novel highly c-oriented tungsten-doped zinc oxide (WZO) thin films with 1 wt% were grown by pulsed laser deposition (PLD) technique on corning 1737F glass substrate. The effects of laser energy on the structural, morphological as well as optical transmission properties of the films were studied. The films were highly transparent with average transmittance exceeding 87% in the wavelength region lying between 400 and 2500 nm. X-ray diffraction analysis (XRD) results indicated that the WZO films had c-axis preferred orientation with wurtzite structure. Film thickness and the full width at half maximum (FWHM) of the (0 0 2) peaks of the films were found to be dependent on laser fluence. The composition determined through Rutherford backscattering spectroscopy (RBS) appeared to be independent of the laser fluence. By assuming a direct band gap transition, the band gap values of 3.36, 3.34 and 3.31 eV were obtained for corresponding laser fluence of 1, 1.7 and 2.7 J cm⁻², respectively. Compared with the reported undoped ZnO band gap value of 3.37 eV, it is conjectured that the observed low band gap values obtained in this study may be attributable to tungsten incorporation in the films as well as the increase in laser fluence. The high transparency makes the films useful as optical windows while the high band gap values support the idea that the films could be good candidates for optoelectronic applications.     

Optimization of the optical and electrical properties of electron beam evaporated aluminum-doped zinc oxide films for opto-electronic applications

Aluminum-doped zinc oxide (AZO) thin films have been deposited by electron beam evaporation technique on glass substrates. The structural, electrical and optical properties of AZO films have been investigated as a function of annealing temperature. It was observed that the optical properties such as transmittance, reflectance, optical band gap and refractive index of AZO films were strongly affected by annealing temperature. The transmittance values of 84% in the visible region and 97% in the NIR region were obtained for AZO film annealed at 475 °C. The room temperature electrical resistivity of 4.6×10⁻³ Ω cm has been obtained at the same temperature of annealing. It was found that the calculated refractive index has been affected by the packing density of the thin films, whereas, the high annealing temperature gave rise to improve the homogeneity of the films. The single-oscillator model was used to analyze the optical parameters such as the oscillator and dispersion energies.     

Preparation and properties of spray-deposited ZnIn2Se4 nanocrystalline thin films

Zinc indium selenide (ZnIn₂Se₄) thin films have been deposited onto amorphous and fluorine doped tin oxide (FTO)-coated glass substrates using a spray pyrolysis technique. Aqueous solution containing precursors of Zn, In, and Se has been used to obtain good quality deposits at different substrate temperatures. The preparative parameters such as substrate temperature and concentration of precursors solution have been optimized by photoelectrochemical technique and are found to be 325 °C and 0.025 M, respectively. The X-ray diffraction patterns show that the films are nanocrystalline with rhombohedral crystal structure having lattice parameter a=4.05 Å. The scanning electron microscopy (SEM) studies reveal the compact morphology with large number of single crystals on the surface. From optical absorption data the indirect band gap energy of ZnIn₂Se₄ thin film is found to be 1.41 eV.     

Investigation of nonlinear optical parameters of zinc based amorphous chalcogenide films

Third order nonlinear optical properties of amorphous Zn_x–S_y–Se_100−x−y chalcogenide films have been investigated using single beam transmission z-scan technique at 1064 nm of Nd:YAG laser. Measurement of optical properties of amorphous Zn_x–S_y–Se_100−x−y chalcogenide films prepared by thermal evaporation technique has been made. X-ray diffraction patterns of chalcogenide films confirm the amorphous nature. Optical band gap (E_g) has been estimated using Tauc's plot method from transmission spectra that is found to decrease with increase in content due to valence band broadening and band tailing the system. Nonlinear refractive index (n₂), nonlinear absorption coefficient (β) and third order nonlinear susceptibility (χ³) of chalcogenide films have been estimated. Self-focusing effect has been observed in closed aperture and reverse saturable absorption in open aperture scheme. Limiting threshold and dynamic range have been calculated from optical limiting studies. The increase in nonlinearity with increase in Zn content has been observed that is understood to be due to decrease in band gap on Zn doping. High nonlinearity makes these films a potential candidate for waveguides, fibers and two photon absorption in optical limiters.     

Structural and optical properties of thermally evaporated 2-(2,3-dihydro-1,5-dimethyl-3-oxo-2-phenyl-1H-pyrazol-4-ylimino)-2-(4-nitrophenyl)acetonitrile thin films

The structural and optical properties of as-deposited and γ-rays irradiated 2-(2,3-dihydro-1,5dimethyl-3-oxo-2-phenyl-1H-pyrazol-4-ylimino)-2-(4-nitrophenyl)acetonitrile (DOPNA) thin films have been reported. The structural properties of as-deposited and γ-rays irradiated DOPNA thin films are characterized by Fourier transformation infrared, X-ray diffraction and transmission electron microscope techniques. The transmittance, T(λ), and reflectance, R(λ), are measured at the normal incidence of light by a double beam spectrophotometer in the wavelength range 200-2200 nm. The refractive and absorption indices have been calculated. The dispersion parameters such as dispersion energy, oscillator energy and dielectric constant at high frequency are evaluated. The data of the absorption coefficient are analyzed in order to determine the type of inter-band electronic transitions and the optical band gap of the films. Other optical absorption parameters, namely, the extinction molar coefficient, oscillator strength and the electric dipole strength, are also calculated.     

Preparation and characterization of electrodeposited Sb2Se3 thin films from non-aqueous media

Semiconducting Sb₂Se₃ thin films have been prepared onto the stainless steel and fluorine doped tin oxide coated glass substrates from non-aqueous media using an electrodeposition technique. The electrodeposition potentials for different bath compositions and concentrations of solution have been estimated from the polarization curves. SbCl₃ and SeO₂ in the volumetric proportion as 1:1 with their equimolar solution concentration of 0.05 M form good quality films. The films are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and optical absorption techniques. The SEM studies show that the film covers the total substrate surface with uneven surface morphology. The XRD patterns of the films obtained by varying compositions and concentrations show that the as-deposited films are polycrystalline with relatively higher grain size for 1:1 composition and 0.05 M concentration. The optical band gap energy for indirect transition in Sb₂Se₃ thin films is found to be 1.195 eV.     

Band gap energy and bowing parameter of In-rich InAlN films grown by magnetron sputtering

The crystal structure, band gap energy and bowing parameter of In-rich In_xAl_1−xN (0.7 < x < 1.0) films grown by magnetron sputtering were investigated. Band gap energies of In_xAl_1−xN films were obtained from absorption spectra. Band gap tailing due to compositional fluctuation in the films was observed. The band gap of the as-grown InN measured by optical absorption method is 1.34 eV, which is larger than the reported 0.7 eV for pure InN prepared by molecular beam epitaxy (MBE) method. This could be explained by the Burstein-Moss effect under carrier concentration of 10²⁰ cm⁻³ of our sputtered films. The bowing parameter of 3.68 eV is obtained for our In_xAl_1−xN film which is consistent with the previous experimental reports and theoretical calculations.     

Effect of deposition parameters on structural, optical and electrical properties of nanocrystalline ZnSe thin films

This paper presents the chemical bath deposition of zinc selenide (n-ZnSe) nanocrystalline thin films on non-conducting glass substrates, in an aqueous alkaline medium using sodium selenosulphate as Se²⁻ ion source. The X-ray diffraction studies show that the deposited ZnSe material is nanocrystalline with a mixture of hexagonal and cubic phase. The direct optical band gap ‘E_g’ for the as-deposited n-ZnSe films is found to be 3.5 eV. TEM studies show that the ZnSe nanocrystals (NCs) are spherical in shape. Formation of ZnSe has been confirmed with the help of infrared (IR) spectroscopy by observing bands corresponding to the multiphonon absorption. We demonstrate the effect of the deposition temperature and reactant concentration on the structural, optical and electrical properties of ZnSe films.     

Preparation of ZnO-doped Al films by spray pyrolysis technique

Al-doped zinc oxide (AZO) thin films have been prepared by spray pyrolysis (SP) technique of zinc acetate and aluminium nitrate, and the effect of thickness on structural and optical properties has been investigated. The structural and optical characteristics of the AZO films were examined by X-ray diffraction (XRD) and double-beam spectrophotometry. These films, deposited on glass substrates at an optimal substrate temperature (T_S = 450 °C), have a polycrystalline texture with a hexagonal structure. Transmission measurements showed that for visible wavelengths, the AZO films have an average transmission of over 90%. The optical parameters have been calculated. The dependence of the refractive index, n, and extinction coefficient, k, on the wavelength for the sprayed films is also reported. Optical band gap of AZO is 3.30 and 3.55 eV, respectively, depending on the film thicknesses.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

Ellipsometric characterization of PbI2 thin film on glass

The optical properties of polycrystalline lead iodide thin film grown on Corning glass substrate have been investigated by spectroscopic ellipsometry. A structural model is proposed to account for the optical constants of the film and its thickness. The optical properties of the PbI₂ layer were modeled using a modified Cauchy dispersion formula. The optical band gap E_g has been calculated based on the absorption coefficient (α) data above the band edge and from the incident photon energy at the maximum index of refraction. The band gap was also measured directly from the plot of the first derivative of the experimental transmission data with respect to the light wavelength around the transition band edge. The band gap was found to be in the range of 2.385±0.010 eV which agrees with the reported experimental values. Urbach's energy tail was observed in the absorption trend below the band edge and was found to be related to Urbach's energy of 0.08 eV.     

Spray pyrolysis deposition of ZnO thin films on FTO coated substrates from zinc acetate and zinc chloride precursor solution at different growth temperatures

ZnO thin films were fabricated using zinc chloride and zinc acetate precursors by the spray pyrolysis technique on FTO coated glass substrates. The ZnO films were grown in different deposition temperature ranges varying from 400 to 550 °C. Influences of substrate temperature and zinc precursors on crystal structure, morphology and optical property of the ZnO thin films were investigated. XRD patterns of the films deposited using chloride precursor indicate that (1 0 1) is dominant at low temperatures, while those deposited using acetate precursor show that (1 0 1) is dominant at high temperatures. SEM images show that deposition temperature and type of precursor have a strong effect on the surface morphology. Optical measurements show that ZnO films are obviously influenced by the substrate temperatures and different types of precursor solutions. It is observed that as temperature increases, transmittance decreases for ZnO films obtained using zinc chloride precursor, but the optical transmittance of ZnO films obtained using zinc acetate precursor increases as temperature increases.     

Effects of rf power on surface-morphological, structural and electrical properties of aluminium-doped zinc oxide films by magnetron sputtering

Aluminium-doped zinc oxide (ZnO:Al) films were prepared by magnetron sputtering at different radio-frequency powers (P_rf) of 50, 100, 150 and 200 W. The properties of the films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), Raman microscopy, and spectrophotometry with the emphasis on the evolution of compositional, surface-morphological, optical, electrical and microstructural properties. XPS spectra showed that within the detection limit the films are chemically identical to near-stoichiometric ZnO. AFM revealed that root-mean-square roughness of the films has almost linear increase with increasing P_rf. Optical band gap E_gopt of the films increases from 3.31 to 3.51 eV when P_rf increases from 50 to 200 W. A widening E_gopt of the ZnO:Al films compared to the band gap (∼3.29 eV) of undoped ZnO films is attributed to a net result of the competition between the Burstein-Moss effect and many-body effects. An electron concentration in the films was calculated in the range of 3.73 × 10¹⁹ to 2.12 × 10²⁰ cm⁻³. Raman spectroscopy analysis indicated that well-identified peaks appear at around 439 cm⁻¹ for all samples, corresponding to the band characteristics of the wurtzite phase. Raman peaks in the range 573-579 cm⁻¹ are also observed, corresponding to the A₁ (LO) mode of ZnO.     

Optical properties of zinc peroxide and zinc oxide multilayer nanohybrid films

Zinc peroxide and zinc oxide nanoparticles were prepared and self-assembled hybrid nanolayers were built up using layer-by-layer (LbL) technique on the surface of glass substrate using the layer silicate hectorite and an anionic polyelectrolyte, sodium polystyrene sulfonate (PSS). Light absorption, interference and morphological properties of the hybrid films were studied to determine their thickness and refractive index. The influence of layer silicates and polymers on the self-organizing properties of ZnO₂ and ZnO nanoparticles was examined. X-ray diffraction revealed that ZnO₂ powders decomposed to ZnO (zincite phase) at relatively low temperatures (less than 200 °C). The optical thickness of the films ranged from 190 to 750 nm and increased linearly with the number of layers. Band gap energies of the ZnO₂/hectorite films were independent from the layer thickness and were larger than that of pure ZnO₂ nanodispersion. Decomposition of ZnO₂ to ZnO and O₂ at 400 °C resulted in the decrease of the band gap energy from 3.75 to 3.3 eV. Concomitantly, the refractive index increased in correlation with the formation of the zincite ZnO phase. In contrast, the band gap energies of the ZnO₂/PSS hybrid films decreased with the thickness of the nanohybrid layers. We ascribe this phenomenon to the steric stabilization of primary ZnO₂ particles present in the confined space between adjacent layers of hectorite sheets.