Structural, compositional, thermal resistant and hydro-oleophobic properties of fluorine based block-co-polymer films on quartz substrates by wet chemical process

Crack free and smooth surfaces of poly [4,5-difluoro 2,2-bis (trifluoromethyl)-(1,3 dioxole)-co-tetrafluoroethylene] (TFE-co-TFD) thin films have been deposited by wet chemical dip coating technique on polished quartz and glass slide substrates. The deposited films have been subjected to annealing at different temperatures ranging from 100 to 500 °C for 1 h in argon atmosphere. The elemental composition of the as-deposited (xerogel) thin film as well as film annealed at 400 °C was measured by X-ray photoelectron spectroscopy and observed that there was no change in the composition of the film. X-ray diffraction pattern revealed the amorphous behaviour of both as-deposited and film annealed at 400 °C. Surface morphology and elemental composition of the films have been examined by employing scanning electron microscopy attached with energy dispersive X-ray analyser, respectively. It was found that as the annealing temperature increased from 100 to 400 °C, nano-hemisphere-like structures have been grown, which in turn has shown increase in the water contact angle from 122^o to 148^o and oil (peanut) contact angle from 85° to 96°. No change in the water contact angle (122°) has been observed when the films deposited at room temperature were heated in air from 30 to 80 °C as well as exposed to steam for 8 days for 8 h/day indicating thermal stability of the film.     

Opto-electrical properties of amorphous carbon thin film deposited from natural precursor camphor

A simple thermal chemical vapor deposition technique is employed for the pyrolysis of a natural precursor “camphor” and deposition of carbon films on alumina substrate at higher temperatures (600-900 °C). X-ray diffraction measurement reveals the amorphous structure of these films. The carbon films properties are found to significantly vary with the deposition temperatures. At higher deposition temperature, films have shown predominately sp²-bonded carbon and therefore, higher conductivity and lower optical band gap (Tauc gap). These amorphous carbon (a-C) films are also characterized with Raman and X-ray photoelectron spectroscopy. In addition, electrical and optical properties are measured. The thermoelectric measurement shows these as-grown a-C films are p-type in nature.     

High-throughput synthesis and characterization of Mg1−xCaxO films as a lattice and valence-matched gate dielectric for ZnO based field effect transistors

Using composition-spread technique, we have grown metastable Mg_1−xCa_xO solid solution films on ZnO layers by pulsed laser deposition. All the films exhibited (1 1 1) oriented cubic phase. Despite a large miscibility gap, no phase separation took place at growth temperatures up to 700 °C, whereas an optimal growth temperature was found at 400 °C in terms of the crystallinity. The composition-spread films were characterized by X-ray diffraction mapping technique. Both lattice parameters and diffraction intensity increased with increasing the CaO composition. The present isovalent heterointerfaces realized the perfect lattice-matching by properly adjusting the CaO composition, leading to particular interest for ZnO based field effect transistors.     

The influence of substrate temperature and annealing on the properties of pulsed laser-deposited YIG films on fused quartz substrate

Yttrium iron garnet (YIG) thin films were deposited on fused quartz substrate at different substrate temperatures (T_s) varying from room temperature (RT) to 850 °C using pulsed laser deposition (PLD) technique. All the films in the as-deposited state were X-ray amorphous and non-magnetic at RT. The film deposited at RT after annealing at temperatures T_a?700 °C showed both X-ray peaks and the magnetic order. The films deposited at higher T_s (500–850 °C) and then annealed at 700 °C resulted in better-quality films with higher 4πM_s value. The highest value of magnetization was for the sample deposited at 850 °C and annealed at 700 °C, which is 68% of the bulk 4πM_s value.     

Control over the wettability of amorphous carbon films in a large range from hydrophilicity to super-hydrophobicity

Control of wettability is of significance in industry as well as our daily live. Amorphous carbon (a-C) films with nanostructured surface were deposited on silicon and glass substrates at different substrate temperatures through a magnetron sputtering technique. The microstructures of the a-C films were studied by SEM and XPS, which indicate that the surface of the a-C films deposited at room temperature are smooth due to their much dense sp³-bonded carbon, while they turn to be more porous graphite-like structure with elevated deposition temperature. The water contact angle (CA) measurements show that these pure carbon films exhibit different wettability, ranging from hydrophilicity with CA less than 40° to super-hydrophobicity with CA of 152°, which reveal that the surface wettability of a-C films can be controlled well by using nanostructures with various geometrical and carbon state features. The graphite-like carbon film deposited at 400 °C without any modification exhibits super-hydrophobic properties, due to the combining microstructures of spheres with nanostructures of protuberances and interstitials. It may have great significance on the study of wettability and relevant applications.     

Influence of deposition temperature on the structural and morphological properties of Be3N2 thin films grown by reactive laser ablation

Be₃N₂ thin films have been grown on Si(1 1 1) substrates using the pulsed laser deposition method at different substrate temperatures: room temperature (RT), 200 °C, 400 °C, 600 °C and 700 °C. Additionally, two samples were deposited at RT and were annealed after deposition in situ at 600 °C and 700 °C. In order to obtain the stoichiometry of the samples, they have been characterized in situ by X-ray photoelectron (XPS) and reflection electron energy loss spectroscopy (REELS). The influence of the substrate temperature on the morphological and structural properties of the films was investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). The results show that all prepared films presented the Be₃N₂ stoichiometry. Formation of whiskers with diameters of 100-200 nm appears at the surface of the films prepared with a substrate temperature of 600 °C or 700 °C. However, the samples grown at RT and annealed at 600 °C or 700 °C do not show whiskers on the surface. The average root mean square (RMS) roughness and the average grain size of the samples grown with respect the substrate temperature is presented. The films grown with a substrate temperature between the room temperature to 400 °C, and the sample annealed in situ at 600 °C were amorphous; while the αBe₃N₂ phase was presented on the samples with a substrate temperature of 600 °C, 700 °C and that deposited with the substrate at RT and annealed in situ at 700 °C.     

Influence of substrate temperature on electrical and optical properties of p-type semitransparent conductive nickel oxide thin films deposited by radio frequency sputtering

Nickel oxide thin films were deposited on fused silica and Si(1 0 0) substrates at different substrate temperatures ranging from room temperature to 400 °C using radio frequency reactive magnetron sputtering from a Ni metal target in a mixture of O₂ and Ar. With the increase of substrate temperature, nickel oxide films deposited on the Si substrates exhibit transition from amorphous to poly-crystalline structures with different preferred orientations of NiO(2 0 0) and (1 1 1). The films deposited at higher temperature exhibit higher Ni²⁺/Ni³⁺ ratio. With substrate temperature increasing from room temperature to 400 °C, the electrical resistivities of nickel oxide films increase from (2.8 ± 0.1) × 10⁻² to (8.7 ± 0.1) Ω cm, and the optical band-gap energies increase from 3.65 to 3.88 eV. A p-nickel oxide/n-zinc oxide heterojunction was fabricated to confirm the p-type conduction of nickel oxide thin film, which exhibited a steadily rectifying behavior.     

The role of antiphase boundaries during ion sputtering and solid phase epitaxy of Si(0 0 1)

The Si(0 0 1) surface morphology during ion sputtering at elevated temperatures and solid phase epitaxy (SPE) following ion sputtering at room temperature has been investigated using scanning tunneling microscopy. Two types of antiphase boundaries form on Si(0 0 1) surfaces during ion sputtering and SPE. One type of antiphase boundary, the AP2 antiphase boundary, contributes to the surface roughening. AP2 antiphase boundaries are stable up to 700 °C, and ion sputtering and SPE performed at 700 °C result in atomically flat Si(0 0 1) surfaces.     

Fabrication of densely distributed Si nanorods by Ar-ion bombardment

For the direct fabrication of densely distributed one dimensional nanostructures on Si substrates, Si (1 0 0) surfaces were bombarded by obliquely incident 3 keV Ar⁺ ions with a simultaneous supply of Mo seed atoms at various temperatures ranging from room temperature to 400 °C. The surface sputtered at room-temperature with Mo seeding was characterized by the nanocones pointing in the direction of the incident ion beam. In addition, they possessed a so-called “web” at their acute-angle side. This web decreased in size with an increase in the sputtering temperature. Thus, the projections fabricated at elevated temperatures were featured by the nanorod-like structure rather than conical structure. With increasing the sputtering temperature, projections decreased in base diameter (from ∼90 nm at 200 °C to ∼50 nm at 400 °C) while they increased in both length (from ∼160 nm at 200 °C to ∼240 nm at 400 °C) and numerical density (from ∼5 × 10⁷ mm⁻² at 200 °C to ∼1.2 × 10⁸ mm⁻² at 400 °C). The controlled fabrication of such densely distributed one dimensional nanoprojections on Si using ion beam technique, we believe, would open up a variety of applications such as nanoelectronics and optoelectronics devices.     

ZnO thin films on Si(1 1 1) grown by pulsed laser deposition from metallic Zn target

ZnO thin films with highly c-axis orientation have been fabricated on p-type Si(1 1 1) substrates at 400 °C by pulsed laser deposition (PLD) from a metallic Zn target with oxygen pressures between 0.1 and 0.7 mbar. Experimental results indicate that the films deposited at 0.3 and 0.5 mbar have better crystalline and optical quality and flatter surfaces than the films prepared at other pressures. The full width at half maximum (FWHM) of (0 0 0 2) diffraction peak decreases remarkably from 0.46 to 0.19° with increasing annealing temperature for the film prepared at 0.3 mbar. In photoluminescence (PL) spectra at room temperature, the annealed film at 700 °C exhibits a smaller ultraviolet (UV) peak FWHM of 108 meV than the as-grown film (119 meV). However, an enhanced deep-level emission is observed. Possible origins to above results are discussed.     

Annealing induced microstructural evolution of electrodeposited electrochromic tungsten oxide films

A significant influence of microstructure on the electrochromic and electrochemical performance characteristics of tungsten oxide (WO₃) films potentiostatically electrodeposited from a peroxopolytungstic acid (PPTA) sol has been evaluated as a function of annealing temperature. Powerful probes like X-ray diffractometry (XRD), transmission electron microscopy (TEM), UV-vis spectrophotometry, multiple step chronoamperometry and cyclic voltammetry have been employed for the thin film characterization. The as-deposited and the film annealed at 60 °C are composed of nanosized grains with a dominant amorphous phase, as well as open structure which ensues from a nanoporous matrix. This ensures a greater number of electroactive sites and a higher reaction area thereby manifesting in electrochromic responses superior to that of the films annealed at higher temperatures. The films annealed at temperatures ≥250 °C are characterized by a prominent triclinic crystalline structure and a hexagonal phase co-exists at temperatures ≥400 °C. The deleterious effect on the electrochromic properties of the film with annealing is ascribed to the loss of porosity, densification and the increasing crystallinity and grain size. Amongst all films under investigation, the film annealed at 60 °C exhibits a high transmission modulation (ΔT ∼ 68%) and coloration efficiency (η ∼ 77.6 cm² C⁻¹) at λ = 632.8 nm, charge storage capacity (Q_ins ∼ 21 mC cm⁻²), diffusion coefficient (6.08 × 10⁻¹⁰ cm² s⁻¹), fast color-bleach kinetics (t_c ∼ 275 s and t_b ∼ 12.5 s) and good electrochemical activity, as well as reversibility for the lithium insertion-extraction process upon cycling. The remarkable potential, which the film annealed at 60 °C has, for practical “smart window” applications has been demonstrated.     

Photoluminescence properties of powder and pulsed laser-deposited PbS nanoparticles in SiO2

Thin films of lead sulfide (PbS) nanoparticles embedded in an amorphous silica (SiO₂) host were grown on Si(1 0 0) substrates at different temperatures by the pulsed laser deposition (PLD) technique. Surface morphology and photoluminescence (PL) properties of samples were analyzed with scanning electron microscopy (SEM) and a 458 nm Ar⁺ laser, respectively. The PL data show a blue-shift from the normal emission at ∼3200 nm in PbS bulk to ∼560-700 nm in nanoparticulate PbS powders and thin films. Furthermore, the PL emission of the films was red-shifted from that of the powders at ∼560 to ∼660 nm. The blue-shifting of the emission wavelengths from 3200 to ∼560-700 nm is attributed to quantum confinement of charge carriers in the restricted volume of nanoparticles, while the red-shift between powders and thin-film PbS nanoparticles is speculated to be due to an increase in the defect concentration. The red-shift increased slightly with an increase in deposition temperature, which suggests that there has been a relative growth in particle sizes during the PLD of the films at higher temperatures. Generally, the PL emission of the powders was more intense than that of the films, although the intensity of some of the films was improved marginally by post-deposition annealing at 400 °C. This paper compares the PL properties of powder and pulsed laser-deposited thin films of PbS nanoparticles and the effects of deposition temperatures.     

Transport and optical properties of amorphous carbon and hydrogenated amorphous carbon films

In this paper we report on the electrical and optical properties of amorphous carbon (a-C) and hydrogenated amorphous carbon (a-C:H) films. Resistivity of both types of films decreases with increase in temperature. At lower temperatures (60-250 K) the electron transport is due to variable range hopping for the a-C films. At higher temperatures (300-430 K) it is thermally activated for both types of films. Analysis of the heterojunction between diamond-like carbon (DLC) and bulk silicon (Si) leads to the conclusion that our a-C films are of n-type and our a-C:H films are of p-type. The optical measurements with DLC revealed a Tauc bandgap of 0.6 eV for the a-C films and 1-1.2 eV for the a-C:H films. An Urbach energy around 170 meV could be determined for the a-C:H films. Strain versus resistance plots were measured resulting in piezoresistive gauge factors around 50 for the a-C films and in between 100 and 1200 for the a-C:H films.     

Amorphous to crystalline phase transition in pulsed laser deposited silicon carbide

SiC thin films were grown on Si (1 0 0) substrates by excimer laser ablation of a SiC target in vacuum. The effect of deposition temperature (up to 950 °C), post-deposition annealing and laser energy on the nanostructure, bonding and crystalline properties of the films was studied, in order to elucidate their transition from an amorphous to a crystalline phase. Infra-red spectroscopy shows that growth at temperatures greater than 600 °C produces layers with increasingly uniform environment of the Si-C bonds, while the appearance of large crystallites is detected, by X-ray diffraction, at 800 °C. Electron paramagnetic resonance confirms the presence of clustered paramagnetic centers within the sp² carbon domains. Increasing deposition temperature leads to a decrease of the spin density and to a temperature-dependent component of the EPR linewidth induced by spin hopping. For films grown below 650 °C, post-deposition annealing at 1100 °C reduces the spin density as a result of a more uniform Si-C nanostructure, though large scale crystallization is not observed. For greater deposition temperatures, annealing leads to little changes in the bonding properties, but suppresses the temperature dependent component of the EPR linewidth. These findings are explained by a relaxation of the stress in the layers, through the annealing of the bond angle disorder that inhibits spin hopping processes.     

Epitaxial growth of InN on nearly lattice-matched (Mn,Zn)Fe2O4

We have grown InN films on nearly lattice-matched (Mn,Zn)Fe₂O₄ (111) substrates at low temperatures by pulsed laser deposition (PLD) and investigated their structural properties. InN films grown at substrate temperatures above 400 °C show poor crystallinity, and their in-plane epitaxial relationship is [10-10]InN//[11-2](Mn,Zn)Fe₂O₄, which means that their lattice mismatch is quite large (11%). By contrast, high quality InN films with flat surfaces can be grown at growth temperatures lower than 150 °C with the ideal in-plane epitaxial relationship of [11-20]InN//[11-2](Mn,Zn)Fe₂O₄, which produces lattice mismatches of as low as 2.0%. X-ray reflectivity measurements have revealed that the thickness of the interfacial layer between the InN and the substrates is reduced from 14 to 8.4 nm when the growth temperature is decreased from 400 °C to room temperature. This suppression of the interface reactions by reducing the growth temperature is probably responsible for the improvement in crystalline quality. These results indicate that the use of (Mn,Zn)Fe₂O₄ (111) substrates at low growth temperatures allows us to achieve nearly lattice matched epitaxial growth of InN.     

The effects of substrate temperature on the structure, morphology and photoluminescence properties of pulsed laser deposited SrAl2O4:Eu,Dy thin films

In this study, SrAl₂O₄:Eu²⁺,Dy³⁺ thin film phosphors were deposited on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique. The films were deposited at different substrate temperatures in the range of 40-700 °C. The structure, morphology and topography of the films were determined by using X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). Photoluminescence (PL) data was collected in air at room temperature using a 325 nm He-Cd laser as an excitation source. The PL spectra of all the films were characterized by green phosphorescent photoluminescence at ∼530 nm. This emission was attributed to 4f⁶5d¹→4f⁷ transition of Eu²⁺. The highest PL intensity was observed from the films deposited at a substrate temperature of 400 °C. The effects of varying substrate temperature on the PL intensity were discussed.     

Early-stage ordering in in-situ annealed Fe51Pt49 films

We evidenced an early-stage ordering (ESO) in Fe₅₁Pt₄₉ film before the appearance of superlattice diffraction (long-range-order, LRO) using 40-nm-thick films prepared by magnetron sputtering onto quartz substrate. The appearance of L1₀ phase for samples deposited at substrate temperatures (T_s) 400 °C and higher was verified by X-ray diffraction. Surface roughness of Fe₅₁Pt₄₉ films, obtained via X-ray specular reflectivity with computational fitting, increases from 3.8 to 11 Å as T_s is increased from 25 to 275 °C. As further increase of T_s to 375 °C, the roughness drops to 3.2 Å and then increases again to 38 Å with T_s up to 700 °C. Measurement on residual strain demonstrates that it is initially compressive at T_s<400 °C. Thereafter the strain transfers to a tensile one and increases in magnitude as increasing T_s up to 700 °C corresponding to LRO transformation. Local atomic rearrangement is observed for samples deposited at T_s>250 °C by using extended X-ray absorption fine structure. Coercivity of films increases from 10 to 460 Oe as T_s increase from 25 to 375 °C (ESO) and then from 460 to 10,700 Oe with T_s 375-700 °C (normal LRO). The worked out quantitative estimation of ESO engages with that of LRO before T_s 400 °C.     

Dielectric behavior of spin-deposited nanocrystalline nickel-zinc ferrite thin films processed by citrate-route

Nanocrystalline nickel-zinc ferrite thin films with the general formula Ni_1−xZn_xFe₂O₄, where x=0.0, 0.2, 0.4 and 0.6 were fabricated via a chemical route known as the citrate precursor route. These films were spin-deposited on indium-tin oxide coated glass, fused quartz and amorphous Si-wafer substrates, and annealed at various temperatures up to 650 °C. The films annealed below 400 °C were found to be X-ray amorphous, while the films annealed at and above 400 °C were polycrystalline exhibiting a single-phase spinel structure. The average grain size of the films evaluated by transmission electron microscopy, is found to be in the range 4-8.5 nm. The room temperature DC resistivity of the films is in the range 10³-10⁷ Ω m. Dielectric constant and dielectric loss were measured in the frequency range 100 Hz-1 MHz. Dielectric constant of the films is found to lie between 25 and 44, while the loss factor is if the order of 10⁻². The higher values of the dielectric constant for films having higher zinc concentration are attributable to the enhanced hopping between Fe²⁺ and Fe³⁺ ions in these samples. The M-H hysteresis measurement of the nickel ferrite thin films annealed at 650 °C showed narrow hysteresis loop—a characteristic of soft ferromagnetic material.     

Stability of MgO(1 1 1) films grown on 6H-SiC(0 0 0 1) by molecular beam epitaxy for two-step integration of functional oxides

Crystalline magnesium oxide (MgO) (1 1 1), 20 Å thick, was grown by molecular beam epitaxy (MBE) on hydrogen cleaned hexagonal silicon carbide (6H-SiC). The films were further heated to 740 °C and 650 °C under different oxygen environments in order to simulate processing conditions for subsequent functional oxide growth. The purpose of this study was to determine the effectiveness and stability of crystalline MgO films and the MgO/6H-SiC interface for subsequent heteroepitaxial deposition of multi-component, functional oxides by MBE or pulsed laser deposition processes. The stability of the MgO films and the MgO/6H-SiC interface was found to be dependent on substrate temperature and the presence of atomic oxygen. The MgO films and the MgO/6H-SiC interface are stable at temperatures up to 740 °C at 1.0 × 10⁻⁹ Torr for extended periods of time. While at temperatures below 400 °C exposure to the presence of active oxygen for extended periods of time has negligible impact, exposure to the presence of active oxygen for more than 5 min at 650 °C will degrade the MgO/6H-SiC interface. Concurrent etching and interface breakdown mechanisms are hypothesized to explain the observed effects. Further, barium titanate was deposited by MBE on bare 6H-SiC(0 0 0 1) and MgO(1 1 1)/6H-SiC(0 0 0 1) in order to evaluate the effectiveness of the MgO as a heteroepitaxial template layer for perovskite ferroelectrics.     

The influence of substrate temperature on the morphology, optical and electrical properties of thermal-evaporated ZnTe Thin Films

The structural, morphological, optical and electrical properties of ZnTe films deposited by evaporation were investigated as a function of substrate temperature (at −123 and 27 °C) and post-deposition annealing temperature (at 200, 300 and 400 °C). It was determined that films deposited at both substrate temperatures were polycrystalline in nature with zinc-blende structure and a strong (1 1 1) texture. A small Te peak was detected in XRD spectra for both substrate temperatures, indicating that as-deposited ZnTe films were slightly rich in Te. Larger grains and a tighter grain size distribution were obtained with increased substrate temperature. Scanning electron microscopy (SEM) studies showed that the microstructures of the as-deposited films agreed well with the expectations from structure zone model. Post-deposition annealing induced further grain growth and tightened the grain size distribution. Annealing at 400 °C resulted in randomization in the texture of films deposited at both substrate temperatures. Optical spectroscopy results of the films indicated that the optical band gap value increased from 2.13 to 2.16 eV with increased substrate temperature. Increasing the annealing temperature sharpened the band-edge. Resistivity measurements showed that the resistivity of films deposited at substrate temperatures of −123 and 27 °C were 32 Ω cm, and 1.0 × 10⁴ Ω cm, respectively with corresponding carrier concentrations of 8.9 × 10¹⁵ cm⁻³ and 1.5 × 10¹⁴ cm⁻³. Annealing caused opposite changes in the film resistivity between the samples prepared at substrate temperatures of −123 and 27 °C.