Development of electronic structure of Ni thin films on Cu(0 0 1) surfaces

We have traced the development of the Ni electronic structure with thickness variation on flat and nano-structured Cu(0 0 1) surfaces by means of photoemission spectroscopy. The binding energy of the Ni 2p_3/2 main peak and satellite peak is found to have shifted monotonically in the direction opposite to each other, with the increase of Ni coverage. The reduced binding energy of the thin film’s main peak is strongly correlated to the Cu 4s/Ni 3d interfacial hybridization effect (s/d IHE) and the narrowing of the d band with the reduction of dimensions, while the increased satellite binding energy results from the combination of interface hybridization and expansion of an extended 4s-like state towards the vacuum. The center of the Ni d_xy band is predicted to shift closer to the Fermi level with increasing film thickness. Enhanced satellite intensity in thin films is observed, correlating to the narrowing of the d band with decreased film thickness. Through comparison of Ni films grown on flat versus nano-structured Cu(0 0 1) surfaces, the mixing of Cu and Ni atoms is found to be enhanced at the terrace edge region and consequently a larger s/d IHE is predicted for Ni on the nano-structured surface.     

Rate coefficients measurement for the energy-pooling collisions Cs(5D) + Cs(5D) → Cs(6S) + Cs(nl = 9D, 11S, 7F)

We report experimental rate coefficients for the energy-pooling collisions Cs(5D) + Cs(5D) → Cs(6S) + Cs(nl = 9D, 11S, 7F). In the experiment the Cs(5D) state was populated via photodissociation of Cs₂ molecules using an argon-ion laser at wavelength 488.0 nm. We also consider the competing process 6P_1/2 + 7S → 6S + (nl = 9D, 11S, 7F) that might also populate 9D, 11S and 7F. An intermodulation technique was used to select the fluorescence contributions due only to the process 6P_1/2 + 7S → 6S + (nl = 9D, 11S, 7F). The excited atom (nl_J) density and spatial distribution were mapped by monitoring the absorption of a counterpropagating probe laser beam tuned to various transitions. The measured excited atom densities are combined with measured fluorescence ratios to yield rate coefficients for the energy-pooling collisions Cs(5D) + Cs(5D) → Cs(6S) + Cs(nl = 9D, 11S, 7F). The rate coefficients for nl = 9D, 11S, 7F are (4.1 ± 2.0) × 10⁻¹⁰ cm³ s⁻¹, (1.6 ± 0.8) × 10⁻¹⁰ cm³ s⁻¹ and (3.6 ± 1.8) × 10⁻¹⁰ cm³ s⁻¹, respectively. The contributions to the rate coefficients from other energy transfer processes are also discussed.     

Density functional study of hypophosphite adsorption on Ni (1 1 1) and Cu (1 1 1) surfaces

Surface structures and electronic properties of hypophosphite, H₂PO₂⁻, molecularly adsorbed on Ni(1 1 1) and Cu(1 1 1) surfaces are investigated in this work by density functional theory at B3LYP/6-31++g(d, p) level. We employ a four-metal-atom cluster as the simplified model for the surface and have fully optimized the geometry and orientation of H₂PO₂⁻ on the metal cluster. Six stable orientations have been discovered on both Ni (1 1 1) and Cu (1 1 1) surfaces. The most stable orientation of H₂PO₂⁻ was found to have its two oxygen atoms interact the surface with two PO bonds pointing downward. Results of the Mulliken population analysis showed that the back donation from 3d orbitals of the transition metal substrate to the unfilled 3d orbital of the phosphorus atom in H₂PO₂⁻ and 4s orbital's acceptance of electron donation from one lone pair of the oxygen atom in H₂PO₂⁻ play very important roles in the H₂PO₂⁻ adsorption on the transition metals. The averaged electron configuration of Ni in Ni₄ cluster is 4s^0.634p^0.023d^9.35 and that of Cu in Cu₄ cluster is 4s^1.004p^0.033d^9.97. Because of this subtle difference of electron configuration, the adsorption energy is larger on the Ni surface than on the Cu surface. The amount of charge transfers due to above two donations is larger from H₂PO₂⁻ to the Ni surface than to the Cu surface, leading to a more positively charged P atom in Ni_nH₂PO₂⁻ than in Cu_nH₂PO₂⁻. These results indicate that the phosphorus atom in Ni_nH₂PO₂⁻ complex is easier to be attacked by a nucleophile such as OH⁻ and subsequent oxidation of H₂PO₂⁻ can take place more favorably on Ni substrate than on Cu substrate.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Spin-pumping-enhanced magnetic damping in ultrathin Cu(0 0 1)/Co/Cu and Cu(0 0 1)/Ni/Cu films

The influence of the Cu capping layer thickness on the spin pumping effect in ultrathin epitaxial Co and Ni films on Cu(0 0 1) was investigated by in situ ultrahigh vacuum ferromagnetic resonance. A pronounced increase in the linewidth is observed at the onset of spin pumping for capping layer thicknesses d_Cu larger than 5 ML, saturating at d_Cu = 20 ML for both systems. The spin mixing conductance for Co/Cu and Ni/Cu interfaces was evaluated.     

Photoemission from the valence bands of Ce(1 1 1) on W(1 1 0)

We report a photoelectron spectroscopic study of the valence bands of epitaxial Ce(1 1 1) films grown on W(1 1 0) at room temperature. The evolution of γ → α → γ like phase transition of Ce is observed with increasing Ce coverage and the valence-band structures of γ-like Ce film are determined. The 4f and 5d photoemission cross sections in the photon energy region from 20 eV to 130 eV are presented and discussed. A 5d-like surface state and a 6s band bottom are identified.     

Formation of doubly excited He atoms during scattering of He ions from a clean and oxygen covered Ni(1 1 0) surface

The formation of doubly excited states of He atoms during collisions of He²⁺ ions with energies between 60 eV and 1 keV with a Ni(1 1 0) surface is studied via Auger electron spectroscopy. We observe that the electron spectra from autoionization of doubly excited states of 2s², 2s2p, 2p² configurations show a pronounced dependence on the coverage of the target surface with oxygen. For a controlled O₂ adsorption on the Ni(1 1 0) surface we can explain the resulting changes in the electron spectra by the modification of the work function of the target surface. Thermal desorption and dissolution into the bulk of surface contaminations at elevated temperatures provides an alternative interpretation of recent work where the local electron spin polarization of a Ni(1 1 0) surface was deduced from changes in the electron spectra as function of target temperature.     

Quantum interference effects in a multi-driven transition Fg = 3 ↔ Fe = 2

We calculated and studied the quantum coherence effects of a degenerate transition F_g = 3 ↔ F_e = 2 system interacting with a weak linearly polarized (with σ_± components) probe light and a strong linearly polarized (with σ_± components) coupling field. Due to the competition between the drive Rabi frequency and the Zeeman splitting, electromagnetically induced transparency (EIT) and electromagnetically induced absorption (EIA) are appeared at the different values of applied magnetic field in both cases that the Zeeman splitting of excited state Δe is smaller than the Zeeman splitting of ground state Δg (i.e., Δe < Δg) and Δe > Δg. It is shown that the resonance is broader and contrasts are higher for Δe < Δg than that for Δe > Δg at the same Rabi frequencies of probe and coupling fields.     

Adsorption of iso-butane on ZnO(0 0 0 1)-Zn

Presented are thermal desorption spectroscopy (TDS) and adsorption probability measurements of iso-butane on the Zn-terminated surface of ZnO. The initial adsorption probability, S₀, decreases linearly from 0.57 to 0.22 (±0.02) with impact energy, E_i = 0.74-1.92 eV, and is independent of adsorption temperature, T_s = 91-114 K (±5 K), indicating non-activated molecular adsorption. The coverage, Θ, dependent adsorption probabilities, S(Θ), show a cross-over from adsorbate-assisted adsorption (S increases with Θ) to Kisliuk-like dynamics at about the desorption temperature of iso-butane bi-layers (∼110 K). Thus, the adsorption dynamics are precursor-mediated. The enhanced (gas-surface) mass-match, caused by forming a second layer of the alkane, leads to adsorbate-assisted adsorption. A direct fitting procedure of the TDS data yields a pre-exponential factor of 2.5 × 10¹³/s and a coverage dependent heat of adsorption of E_d(Θ) = 39 − 6 ∗ Θ + 2.5 ∗ exp(−Θ/0.07) kJ/mol.     

The adsorption of methylcyclopentane on Pt(1 1 1)

The adsorption of methylcyclopentane (MCP) on Pt(1 1 1) has been studied using the atom superposition and electron delocalization (ASED-MO) molecular orbital method. Results show a weak interaction with the metallic surface. The adsorption energy is rather independent of the adsorption site coordination number. We find that Pt 6s, 6p_z and 5d_z² orbitals are involved in the bonding with MCP. There is no bonding between the carbon ring and the Pt surface and the interaction comes from the hydrogen atoms to the surface.     

Surface structure of K/Pd(1 0 0) and the effect of H coadsorption: Density functional theory calculations

We have performed density-functional theory calculations to study the atomic structure of the K/Pd(1 0 0)-p(2 × 2) and -c(2 × 2) surfaces formed at 0.25 ML and 0.5 ML, respectively. We find that K atoms prefer the hollow site with the K adsorption height 2.44 Å for p(2 × 2) and 2.50 Å c(2 × 2). The first interlayer spacing (d₁₂) of the Pd(1 0 0) substrate appears slightly contracted from the bulk value as Δd₁₂ = −0.8% and −0.3% for p(2 × 2) and c(2 × 2), respectively. The calculated contraction Δd₁₂ = −0.3% for c(2 × 2) is not in accord with the expansion Δd₁₂ = +1.3% reported by a low-energy electron diffraction (LEED) study. As the origin of this difference, a possibility of hydrogen contamination of the surface sample used in the LEED study is suggested: Our calculations show that the d₁₂ of K/Pd(1 0 0)-c(2 × 2) increases linearly with the coverage of H coadsorption, which leads to an estimation for the H coverage of the surface sample as 0.1-0.4 ML.     

Alloy formation of Co/Ni/Pt(1 1 1)

The initial growth and alloy formation of ultrathin Co films deposited on 1 ML Ni/Pt(1 1 1) were investigated by Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and ultraviolet photoelectron spectroscopy (UPS). A sequence of samples of d_Co Co/1 ML Ni/Pt(1 1 1) (d_Co = 1, 2, and 3 ML) were prepared at room temperature, and then heated up to investigate the diffusion process. The Co and Ni atoms intermix at lower annealing temperature, and Co-Ni intermixing layer diffuses into the Pt substrate to form Ni-Co-Pt alloys at higher annealing temperature. The diffusion temperatures are Co coverage dependent. The evolution of UPS with annealing temperatures also shows the formation of surface alloys. Some interesting LEED patterns of 1 ML Co/1 ML Ni/Pt(1 1 1) show the formation of ordered alloys at different annealing temperature ranges. Further studies in the Curie temperature and concentration analysis, show that the ordered alloys corresponding to different LEED patterns are Ni_xCo_1−xPt and Ni_xCo_1−xPt₃. The relationship between the interface structure and magnetic properties was investigated.     

High resolution analysis of the rotational levels of the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states of SO2

A high resolution (0.0018 cm⁻¹) Fourier transform instrument has been used to record the spectrum of an enriched ³⁴S (95.3%) sample of sulfur dioxide. A thorough analysis of the ν₂, 2ν₂ − ν₂, ν₁, ν₁ + ν₂ − ν₂, ν₃, ν₂ + ν₃ − ν₂, ν₁ + ν₂ and ν₂ + ν₃ bands has been carried out leading to a large set of assigned lines. From these lines ground state combination differences were obtained and fit together with the existing microwave, millimeter, and terahertz rotational lines. An improved set of ground state rotational constants were obtained. Next, the upper state rotational levels were fit. For the (0 1 0), (1 1 0) and (0 1 1) states, a simple Watson-type Hamiltonian sufficed. However, it was necessary to include explicitly interacting terms in the Hamiltonian matrix in order to fit the rotational levels of the (0 2 0), (1 0 0) and (1 0 1) states to within their experimental accuracy. More explicitly, it was necessary to use a ΔK = 2 term to model the Fermi interaction between the (0 2 0) and (1 0 0) levels and a ΔK = 3 term to model the Coriolis interaction between the (1 0 0) and (0 0 1) levels. Precise Hamiltonian constants were derived for the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states.     

Simultaneous observation of oxygen uptake curves and electronic states during room-temperature oxidation on Si(0 0 1) surfaces by real-time ultraviolet photoelectron spectroscopy

Ultraviolet photoelectron spectroscopy was used to measure the oxygen uptake, changes in work function due to the surface dipole layer of adsorbed-oxygen atoms, Δ?_SDL, and changes in band bending due to the defect-related midgap state, ΔBB, simultaneously during oxidation on Si(0 0 1) surface at room-temperature, RT, under an O₂ pressure of 1.3 × 10⁻⁵ Pa. The oxygen dosage dependence of Δ?_SDL revealed that dissociatively adsorbed-oxygen atoms occupy preferentially dimer backbond sites at the initial stage of Langmuir-type adsorption, which is associated with a rapid increase of ΔBB. When raising temperature to ∼600 °C, such preferential occupation of the dimer backbond sites by oxygen atoms is less significant and ΔBB becomes smaller in magnitude. The observed relation between Δ?_SDL and ΔBB indicates that point defects (emitted Si atoms + vacancies) are more frequently generated by oxygen atoms diffusing to the dimer backbond sites at lower temperature in RT −600 °C.     

Combined STM, LEED and DFT study of Ag(1 0 0) exposed to oxygen near atmospheric pressures

We have investigated the interaction of molecular oxygen with the Ag(1 0 0) surface in a temperature range from 130 K to 470 K and an oxygen partial pressure ranging up to 10 mbar by scanning tunneling microscopy, low electron energy diffraction, Auger electron spectroscopy and ab initio density functional calculations. We find that at 130 K, following oxygen exposures of 6000 Langmuirs O₂, the individual oxygen atoms are randomly distributed on the surface. When the sample is exposed to 10 mbar O₂ at room temperature, small, p(2 × 2) reconstructed patches are formed on the surface. After oxidation at ≈470 K and 10 mbar O₂ pressure the surface undergoes a c(4 × 6) reconstruction coexisting with a (6 × 6) superstructure. By ab initio thermodynamic calculations it is shown that the c(4 × 6) reconstruction is an oxygen adsorption induced superstructure which is thermodynamically stable for an intermediate range of oxygen chemical potential.     

Anomalous adsorption of Cs on Pt(1 1 1)

The adsorption of Cs on Pt(1 1 1) surfaces and its reactivity toward oxygen and iodine for coverages θ_Cs?0.15 is reported. These surfaces show unusual “anomalous” behavior compared to higher coverage surfaces. Similar behavior of K on Pt(1 1 1) was previously suggested to involve incorporation of K into the Pt lattice. Despite the larger size of Cs, similar behavior is reported here. Anomalous adsorption is found for coverages lower than 0.15 ML, at which point there is a change in the slope of the work function. Thermal Desorption Spectroscopy (TDS) shows a high-temperature Cs peak at 1135 K, which involves desorption of Cs⁺ from the surface.The anomalous Cs surfaces and their coadsorption with oxygen and iodine are characterized by Auger Electron Spectroscopy (AES), TDS and Low Electron Energy Diffraction (LEED). Iodine adsorption to saturation on Pt(1 1 1)(anom)-Cs give rise to a sharp LEED pattern and a distinctive work function increase. Adsorbed iodine interacts strongly with the Cs and weakens the Cs-Pt bond, leading to desorption of Cs_xI_y clusters at 560 K. Anomalous Cs increases the oxygen coverage over the coverage of 0.25 ML found on clean Pt. However, the Cs-Pt bond is not significantly affected by coadsorbed oxygen, and when oxygen is desorbed the anomalous cesium remains on the surface.     

Surface and subsurface oxide formation on Ni(1 0 0) and Ni(1 1 1)

The oxidation of Ni(1 0 0) and Ni(1 1 1) at elevated temperatures and large oxygen exposures, typical of the methods used in the preparation of NiO(1 0 0) films for surface studies, has been investigated by medium energy ion scattering (MEIS) using 100 keV H⁺ incident ions. Oxide film growth proceeds significantly faster on Ni(1 1 1) than on Ni(1 0 0), but on both surfaces oxide penetration occurs to depths significantly greater than 100 Å with total exposures of 1200 and 6000 L respectively. The metal/oxide interface is extremely rough, with metallic Ni extending to the surface, even for much thicker oxide films on Ni(1 1 1). On Ni(1 1 1), NiO growth occurs with the (1 0 0) face parallel to the Ni(1 1 1) surface and the close-packed 〈1 1 0〉 directions parallel. On Ni(1 0 0) the MEIS blocking curves cannot be reconciled with a single orientation of NiO(1 0 0) (with the 〈1 1 0〉 directions parallel) on the surface, but is consistent with the substantial orientational disorder (including tilt) previously identified by spot-profile analysis LEED.     

Structural evolution of electroless Ni-P coating on Al-12 wt.% Si alloy during heat treatment at high temperatures

The work is concerned with the high-temperature heat treatment of an Al-12 wt.% Si alloy coated by an electroless Ni-P layer. The electroless deposition took place on a pre-treated substrate in a bath containing nickel hypophosphite, nickel lactate and lactic acid. Resulting Ni-P deposit showed a thickness of about 8 μm. The coated samples were heat-treated at 200-550 °C/1-24 h. LM, SEM, EDS and XRD were used to investigate phase transformations. Adherence to the substrate was estimated from the scratch test and microhardness of the heat-treated layers was also measured. It is found that various phase transformations occur, as both temperature and annealing time increase. These include (1) amorphous Ni-P → Ni + Ni₃P, (2) Al + Ni → Al₃Ni, (3) Ni₃P → Ni₁₂P₅ + Ni, (4) Ni₁₂P₅ → Ni₂P + Ni, and (5) Al₃Ni + Ni → Al₃Ni₂. The formation of intermetallic phases, particularly Al₃Ni₂, leads to significant surface hardening, however, too thick layers of intermetallics reduce the adherence to the substrate. Based on the growth kinetics of the intermetallic phases, diffusion coefficients of Ni in Al₃Ni and Al₃Ni₂ at 450-550 °C are estimated as follows: D(Al₃Ni, 450 °C) ≈ 6 × 10⁻¹² cm² s⁻¹, D(Al₃Ni, 550 °C) ≈ 4 × 10⁻¹¹ cm² s⁻¹, D(Al₃Ni₂, 450 °C) ≈ 1 × 10⁻¹² cm² s⁻¹ and D(Al₃Ni₂, 550 °C) ≈ 1 × 10⁻¹¹ cm² s⁻¹. Mechanisms of phase transformations are discussed in relation to the elemental diffusion.     

Oxygen-induced p(3 × 1) reconstruction of the W(1 0 0) surface

The oxidation of the W(1 0 0) surface at elevated temperatures has been studied using room temperature STM and LEED. High exposure of the clean surface to O₂ at 1500 K followed by flash-annealing to 2300 K in UHV results in the formation of a novel p(3 × 1) reconstruction, which is imaged by STM as a missing-row structure on the surface. Upon further annealing in UHV, this surface develops a floreted LEED pattern characteristic of twinned microdomains of monoclinic WO_x, while maintaining the p(3 × 1) missing-row structure. Atomically resolved STM images of this surface show a complex domain structure with single and double W〈0 1 0〉 rows coexisting on the surface in different domains.     

Theoretical study of CO and Pb adsorption on the Ni(1 1 1) and Ni3Al(1 1 1) surfaces

Adsorption of CO molecules and Pb atoms on the Ni(1 1 1) and Ni₃Al(1 1 1) substrates is studied theoretically within an ab initio density-functional-theory approach. Stable adsorption sites and the corresponding adsorption energies are first determined for stoichiometric surfaces. The three-fold hollow sites (fcc for Pb and hcp for CO) are found most favourable on both substrates. Next, the effect of surface alloying by a substitution of selected topmost substrate atoms by Pb or Ni atoms on the adsorption characteristics is investigated. When the surface Al atoms of the Ni₃Al(1 1 1) substrate are replaced by Ni atoms, the Pb and CO adsorption energies approach those for a pure Ni(1 1 1) substrate. The Pb alloying has a more substantial effect. On the Ni₃Al(1 1 1) substrate, it reduces considerably adsorption energy of CO. On the Ni(1 1 1) substrate, CO binding strengthens slightly upon the formation of the Ni(1 1 1)p(2×2)-Pb surface alloy, whereas it weakens drastically when the Ni(1 1 1)-Pb surface alloy is formed.