Growth of thin, crystalline oxide, nitride, and oxynitride films on NiAl and CoGa surfaces

At 300 K, an amorphous Al-oxide film is formed on NiAl(001) upon oxygen adsorption. Annealing of the oxygen-saturated NiAl(001) surface to 1200 K leads to the formation of thin well-ordered θ-Al₂O₃ films. At 300 K, and low-exposure oxygen atoms are chemisorbed on CoGa(001) on defects and on step edges of the terraces. For higher exposure up to saturation, the adsorption of oxygen leads to the formation of an amorphous Ga-oxide film. The EEL spectrum of the amorphous film exhibits two losses at ≈400 and 690 cm^-1. After annealing the amorphous Ga-oxide films to 550 K thin, well-ordered β-Ga₂O₃ films are formed on top of the CoGa(001) surface. The EEL spectrum of the β-Ga₂O₃ films show strong Fuchs-Kliewer (FK) modes at 305, 455, 645, and 785 cm^-1. The β-Ga₂O₃ films are well ordered and show (2×1) LEED pattern with two domains, oriented perpendicular to each other. The STM study confirms the two domains structure and allows the determination of the two-dimensional lattice parameters of β-Ga₂O₃. The vibrational properties and the structure of β-Ga₂O₃ on CoGa(001) and θ-Al₂O₃ on NiAl(001) are very similar. Ammonia adsorption at 80 K on NiAl(111) and NiAl(001) and subsequent thermal decomposition at elevated temperatures leads to the formation of AlN. Well-ordered and homogeneous AlN thin films can be prepared by several cycles of ammonia adsorption and annealing to 1250 K. The films render a distinct LEED pattern with hexagonal [AlN/NiAl(111)] or pseudo-twelve-fold [AlN/NiAl(001)] symmetry. The lattice constant of the grown AlN film is determined to be a_AlN= 3.11 Å. EEL spectra of AlN films show a FK phonon at 865 cm^-1. The electronic gap is determined to be E_g= 6.1±0.2 eV. GaN films are prepared by using the same procedure on the (001) and (111) surfaces of CoGa. The films are characterized by a FK phonon at 695 cm^-1 and an electronic band gap E_g= 3.5±0.2 eV. NO adsorption at 75 K on NiAl(001) and subsequent annealing to 1200 K leads to the formation of aluminium oxynitride (AlON). An oxygen to nitrogen atomic ratio of ≈2:1 was estimated from the analysis of AES spectra. The AlON films shows a distinct (2×1) LEED pattern and the EEL spectrum exhibits characteristic Fuchs-Kliewer modes. The energy gap is determined to be E_g= 6.6±0.2 eV. The structure of the AlON film is derived from that of θ-Al₂O₃ formed on NiAl(001). Received: 21 March 1997/Accepted: 12 August 1997     

Surface characterization and microstructure of ITO thin films at different annealing temperatures

In this study, the electron beam evaporation method is used to generate an indium tin oxide (ITO) thin film on a glass substrate at room temperature. The surface characteristics of this ITO thin film are then investigated by means of an AFM (atomic force microscopy) method. The influence of postgrowth thermal annealing on the microstructure and surface morphology of ITO thin films are also examined. The results demonstrate that the film annealed at higher annealing temperature (300 °C) has higher surface roughness, which is due to the aggregation of the native grains into larger clusters upon annealing. The fractal analysis reveals that the value of fractal dimension D_f falls within the range 2.16-2.20 depending upon the annealing temperatures and is calculated by the height-height correlation function.     

XPS depth profiling studies of L-CVD SnO2 thin films

In this paper we present the results of the XPS atomic depth profile analysis, using ion beam sputtering, of L-CVD SnO₂ thin films grown on an atomically clean SiO₂ substrate after annealing at 400 °C in dry atmospheric air. From the evolution of the Sn 3d_5/2, O 1s, Si 2p and C 1s core level peaks our experiments allowed the determination of the in depth atomic concentration of the main components of the SnO₂/SiO₂ interface. Thin (few nm) nearly stoichiometric SnO₂ films are present at the topmost layer of the thin films, and progressive intermixing with SnO and silicon oxide is observed at deeper layer. The interface between the Sn and the Si oxide layers (i.e. the effective Sn oxide thickness) is measured at 13 nm.     

Composition, structure and morphology of oxide layers formed on austenitic stainless steel by oxygen plasma immersion ion implantation

Oxygen ions were implanted in to austenitic stainless steel by plasma immersion ion implantation at 400 °C. The implanted samples were characterized by XPS, GIXRD, micro-Raman, AFM, optical and scanning electron microscopies. XPS studies showed the presence of Fe in elemental, as Fe²⁺ in oxide form and as Fe³⁺ in the form of oxyhydroxides in the substrate. Iron was present in the oxidation states of Fe²⁺ and Fe³⁺ in the implanted samples. Cr and Mn were present as Cr³⁺ and Mn²⁺, respectively, in both the substrate and implanted samples. Nickel remained unaffected by implantation. GIXRD and micro-Raman studies showed the oxide to be a mixture of spinel and corundum structures. Optical and AFM images showed an island structure on underlying oxide. This island structure was preserved at different thicknesses. Further, near the grain boundaries more oxide growth was found. This is explained on the basis of faster diffusion of oxygen in the grain boundary regions. Measurement of total hemispherical optical aborptance, α and emittance, ? of the implanted sample show that it has good solar selective properties.     

Surface functionalisation of polymer nanofibres by sputter coating of titanium dioxide

The surface properties of nanofibres are of importance in various applications. In this work, electrospun polyamide nanofibres were used as substrates for creating functional nanostructures on the nanofibre surfaces. A RF magnetron sputter coating was used to deposit the functional layer of titanium dioxide (TiO₂) onto the nanofibres. Atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and environmental scanning electron microscopy (ESEM) were employed to study the topography, grain structure and wetting of the nanofibre surfaces, respectively. The AFM results indicated a significant difference in the morphology of the nanofibres before and after the TiO₂ sputter coating. The XRD analysis showed the amorphous structures of the TiO₂ deposition layer. XPS spectra reflected the chemical features of the deposited nanostructures. The ESEM observation revealed that the surface wettability of TiO₂ sputter coated nanofibres was significantly improved after UV irradiation.     

Multifractal analysis of ITO thin films prepared by electron beam deposition method

In this work, we developed the multifractality and its formalism to investigate the surface topographies of ITO thin films prepared by electron beam deposition method for various annealing temperatures from their atomic force microscopy (AFM) images. Multifractal analysis shows that the spectrum width, Δα (Δα = α_max − α_min), of the multifractal spectra, f(α), can be used to characterize the surface roughness of the ITO films quantitatively. Also, it is found that the f(α) shapes of the as-deposited and annealed films remained left hooked (that is Δf = f(α_min) − f(α_max) > 0), and falls within the range 0.149-0.677 depending upon the annealing temperatures.     

Short-range order in Valenta model of thin films

The present paper deals with the Valenta model for magnetic thin films extended to the entropy construction in its pair representation. The problem of the thin films theory is old, but the Valenta model introduced fifty years ago seems to be still an effective approach requiring however, some modifications. The most important one is connected with the improvement of the entropy construction in the self-consistent way when the correlations are taken into account. The idea is introduced in the present paper and discussed in detail.     

Atomic structure of Cs layer grown on Si(0 0 1)(2 × 1) surface at room temperature

The atomic structure of Cs atoms adsorbed on the Si(0 0 1)(2 × 1) surface has been investigated by coaxial impact collision ion scattering spectroscopy. When 0.5 ML of Cs atoms are adsorbed on Si(0 0 1) at room temperature, it is found that Cs atoms occupy a single absorption site on T3 with a height of 3.18 ± 0.05 Å from the second layer of Si(0 0 1)(2 × 1) surface, and the bond length between Cs and the nearest Si atoms is 3.71 ± 0.05 Å.     

Microstructure, porosity and roughness of RF sputtered oxide thin films: Characterization and modelization

Spinel CoMnFeO₄ thin films are stable materials useful to study the influence of radio-frequency (RF) sputtering experimental conditions on the microstructure of oxide films. It has been demonstrated by various techniques such as electronic and atomic force microscopy (AFM), gas adsorption techniques and ellipsometry, that films prepared with 0.5 Pa sputtering argon pressure and 5 cm target-substrate distance are very dense. On the other hand, the samples obtained under higher pressure and/or longer distances are microporous with a mean pore size generally lower than 2 nm. The specific surface areas of such films reach about 75 m²/g.According to the simple model proposed, the films are made of three layers. From the bottom to the top of the film, the first one at the interface with the substrate is 100% dense. The second layer is made of cylindrical rods set up according to a compact plane. Its porosity is due to the lattice interstices. Hemispheric domes covering each rod make up the third layer, which displays a degree of roughness related to the shape and the hexagonal arrangement of the domes. The surface enhancement factor (SEF), the porosity and roughness, calculated from the model, are in corroboration with the experimental values. The porosity factor is however slightly underestimated by the model for very porous samples.     

Surface partition of ion energy during the growth of TiNx thin films

A simple evaluation of ion-deposited energy during surface displacement of adatoms has been presented for physical vapor deposition technology using an appropriate interaction model. The rf reactive magnetron sputtering deposition of titanium nitride (TiN_x) thin films was taken as evidence supporting the theoretical calculation. The evolution of crystallite morphology dependent on bias (or input power) illustrates that surface and subsurface microstructure of growing films can be optimized by increasing the mobility of adatoms through ion-assistance.     

Optical properties of Al-doped ZnO thin films by ellipsometry

Al-doped ZnO thin films (AZO) were prepared on Si (1 0 0) substrates by using sub-molecule doping technique. The Al content was controlled by varying Al sputtering time. The as-prepared samples were annealed in vacuum chamber at 800 °C for 30 min. From the XRD observations, it is found that all films exhibit only the (0 0 2) peak, suggesting that they have c-axis preferred orientation. The average transmittance of the visible light is above 80%. Spectroscopic ellipsometry was used to extract the optical constants of the films. The absorption coefficient and the energy gap were then calculated. The results show that the absorption edge initially blue-shifts and then red-shifts with increase of Al content.     

X-ray and neutron reflectivity analysis of thin films and superlattices

X-ray and neutron reflectivity measurements provide a wealth of information on thickness and interfacial properties on the nanometer scale. This method is therefore well suited for the study of nano-structured thin films and superlattices. Neutrons provide a different contrast between the elements than X-rays and, in addition, are sensitive to the magnetization in the sample. Using polarized neutrons, magnetic as well as chemical profiles can be probed. In this review a basic introduction into the theory of X-ray and neutron reflectivity is provided along with some recent examples including the oxidation of Fe films and the structural and magnetic properties of Co/Cu superlattices.     

Correlation between density and structure. in boron nitride thin films by X-ray diffraction

* _ion=100 eV. Above E^* _ion the average density (deduced from X-ray reflectivity) shows a strong increase, indicating the sudden appearance of the cubic boron nitride phase consistent with the sp³ concentration deduced from IR absorption spectroscopy. The in-plane X-ray diffraction shows that this cubic phase consists of small nanocrystals of 70 Å linear size. Received: 26 November 1996/Accepted: 27 January 1997     

Properties of NiO thin films deposited by chemical spray pyrolysis using different precursor solutions

NiO thin films have been deposited by chemical spray pyrolysis using a perfume atomizer to grow the aerosol. The influence of the precursor, nickel chloride hexahydrate (NiCl₂·6H₂O), nickel nitrate hexahydrate (Ni(NO₃)₂·6H₂O), nickel hydroxide hexahydrate (Ni(OH)₂·6H₂O), nickel sulfate tetrahydrate (NiSO₄·4H₂O), on the thin films properties has been studied. In the experimental conditions used (substrate temperature 350 °C, precursor concentration 0.2-0.3 M, etc.), pure NiO thin films crystallized in the cubic phase can be achieved only with NiCl₂ and Ni(NO₃)₂ precursors. These films have been post-annealed at 425 °C for 3 h either in room atmosphere or under vacuum. If all the films are p-type, it is shown that the NiO films conductivity and optical transmittance depend on annealing process. The properties of the NiO thin films annealed under room atmosphere are not significantly modified, which is attributed to the fact that the temperature and the environment of this annealing is not very different from the experimental conditions during spray deposition. The annealing under vacuum is more efficient. This annealing being proceeded in a vacuum no better than 10⁻² Pa, it is supposed that the modifications of the NiO thin film properties, mainly the conductivity and optical transmission, are related to some interaction between residual oxygen and the films.     

ZnO thin films on Si(1 1 1) grown by pulsed laser deposition from metallic Zn target

ZnO thin films with highly c-axis orientation have been fabricated on p-type Si(1 1 1) substrates at 400 °C by pulsed laser deposition (PLD) from a metallic Zn target with oxygen pressures between 0.1 and 0.7 mbar. Experimental results indicate that the films deposited at 0.3 and 0.5 mbar have better crystalline and optical quality and flatter surfaces than the films prepared at other pressures. The full width at half maximum (FWHM) of (0 0 0 2) diffraction peak decreases remarkably from 0.46 to 0.19° with increasing annealing temperature for the film prepared at 0.3 mbar. In photoluminescence (PL) spectra at room temperature, the annealed film at 700 °C exhibits a smaller ultraviolet (UV) peak FWHM of 108 meV than the as-grown film (119 meV). However, an enhanced deep-level emission is observed. Possible origins to above results are discussed.     

Substrate and orientation influence on electrical properties of sputtered La-doped PZT thin films

Pb_1−2y/3La_yZr_xTi_1−xO₃ (PLZT) thin films have been prepared “in situ” by multi-target sputtering on Silicon, LaAlO₃ (LAO) and MgO substrates covered with a Pt bottom electrode. The purpose was to grow tetragonal PLZT films (Zr/Ti = 28/72 with different La contents) on these various substrates and to compare their electrical properties. To this aim, Pt was first deposited on the three different substrates to get (1 1 1)Pt/Si, (1 1 1)Pt/LAO and (2 0 0)Pt/MgO. Then PLZT was deposited in a same run on these three kinds of substrates and the influence of La contents and film orientation on electrical properties was investigated. The La content was varied from y = 0 to y = 32 in order to explore the phase transition between ferroelectric and paraelectric phases as a function of the substrate. For large amount of Lanthanum, relaxor behavior has been observed and studied.     

Effects of microwave plasma treatment on the field emission properties of printed carbon nanotubes/Ag nano-particles films

The effects of Ar microwave plasma treatment on field emission properties of the printed carbon nanotubes (CNTs) cathode films using Ag nano-particles as binder were investigated. The field emission J-E characteristics were measured at varied plasma treatment time. Significant improvement in emission current density, emission stability and uniformity were achieved for the Ar treated CNTs films, even though the plasma treatment increased the turn on electric field slightly. High-resolution transmission electron microscopy (HRTEM) and Raman spectroscopy revealed the microstructural changes of CNTs after the plasma treatment. The improved field emission properties of CNTs film can be attributed to the generation of a high density of structural defects after treatment, which increased greatly the possible emission active sites. Besides, the formation of the sharpened and open-ended CNTs tips is all helpful for improving the field emission properties of the treated CNTs.     

Structure and optical properties of ZnS thin films grown by glancing angle deposition

The glancing angle deposition (GLAD) technique was used to deposit ZnS films by electron beam evaporation method. The cross sectional scanning electron microscopy (SEM) image illustrated a highly orientated microstructure composed of slanted column. The atomic force microscopy (AFM) analysis indicated that incident flux angle had significant effects on the nodule size and surface roughness. Under identical nominal thickness, the actual thickness of the GLAD films is related to the incident flux angle. The refractive index and in-plane birefringence of the GLAD ZnS films were discussed, and the maximum birefringence Δn = 0.036 was obtained at incident flux angle of α = 80°. Therefore, the glancing angle deposition technique is a promising way to create a columnar structure with enhanced birefringent property.     

MicroRaman study of the effect of oxide layer on nitriding of Ti-6Al-4V

Ti-6Al-4V samples were subjected to nitrogen ion implantation and low pressure RF plasma nitriding in a PIII equipment after chemical etching in Kroll's reagent. The samples were characterized by optical microscopy, AFM, microRaman, XRD and micro hardness measurements. From microRaman, oxides of titanium were found in the inter-granular β region whereas the oxide on the α region was extremely thin. The oxide on the β region was found to be amorphous and from intensity dependent Raman spectra, it was found to have a layered structure. The top layer was rutile and the inner layer anastase. Presence of Ti₂O₃ was also found. After PIII treatment at 600 °C, microRaman showed the presence of nitride in both the regions and the oxide was absent in the β regions. Also, from intensity dependent Raman spectra, it was found that in-take of nitrogen by β regions was higher. The oxide layer remained unaffected after plasma nitriding. Nitride presence in the α was established by microRaman. Even though Raman spectra from β regions were nearly the same as that of oxide, presence of nitrogen was indicated by the spectra. XRD studies of implanted and nitrided samples showed the prsence of TiN and Ti₂N in implanted sample and presence of Ti₂N in the nitrided sample. The β regions were found to have higher microhardness values after PIII and nitriding treatments. This is attributed to the deeper diffusion of nitrogen in these regions.     

Elaboration of (1 1 1)-oriented La-doped PZT thin films on platinized silicon substrates

PLZT thin films with different thickness were deposited in situ on platinum coated silicon substrates using a multi-target sputtering system. The purpose was to grow (1 1 1)-textured PLZT films on Pt (1 1 1). To this aim, the role of some key parameters on both crystalline quality and electrical properties was investigated. An ultra-thin TiO₂ seeding layer was deposited, prior to PLZT, which strongly affected the crystallographic orientation of the films. The relation between temperature deposition and film crystallinity is analysed. TEM observations show the presence of some very small grains of Zr_0.9La_0.1O_1.95 at the film bottom interface. In the range of thickness investigated, the plot of the inverse capacitance as a function of the film thickness split up into two different curves, each with a linear shape, which however allows determination of a single value of interface capacitance. Above a thickness of 400-500 nm a saturation of the dielectric properties seems to be reached.