Effect of RF power on the properties of transparent conducting zirconium-doped zinc oxide films prepared by RF magnetron sputtering

Transparent and conducting zirconium-doped zinc oxide films with high transparency and relatively low resistivity have been successfully prepared by radio frequency (RF) magnetron sputtering at room temperature. The RF power is varied from 75 to 150W. At first the crystallinity and conductivity of the film are improved and then both of them show deterioration with the increase of the RF power. The lowest resistivity achieved is 2.07×10^-3\Omegacm at an RF power of 100W with a Hall mobility of 16cm²V^-1s^-1 and a carrier concentration of 1.95×10²⁰cm^-3. The films obtained are polycrystalline with a hexagonal structure and a preferred orientation along the c-axis. All the films have a high transmittance of approximately 92% in the visible range. The optical band gap is about 3.33eV for the films deposited at different RF powers.     

Room temperature transparent conducting oxides based on zinc oxide thin films

Doped zinc oxide thin films are grown on glass substrate at room temperature under oxygen atmosphere, using pulsed laser deposition (PLD). O₂ pressure below 1 Pa leads to conductive films. A careful characterization of the film stoichiometry and microstructure using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) concludes on a decrease in crystallinity with Al and Ga additions (≤3%). The progressive loss of the (0 0 2) orientation is associated with a variation of the c parameter value as a function of the film thickness and substrate nature. ZnO:Al and ZnO:Ga thin films show a high optical transmittance (>80%) with an increase in band gap from 3.27 eV (pure ZnO) to 3.88 eV and 3.61 eV for Al and Ga doping, respectively. Optical carrier concentration, optical mobility and optical resistivity are deduced from simulation of the optical data.     

外加磁场对射频磁控溅射制备铝掺杂氧化锌薄膜影响的研究

利用射频磁控溅射法制备了铝掺杂氧化锌(AZO)透明导电薄膜,在传统的磁控溅射系统中引入外加磁场,研究了外加磁场对AZO薄膜沉积速率、形貌结构及光电特性的影响.研究结果表明,外加磁场后薄膜的沉积速率从不加磁场的13.04 nm/min提高到了19.93 nm/min;外加磁场后薄膜表面平整致密、颗粒大小均匀,结晶质量较高,而不加磁场薄膜表面形貌呈蠕虫状,薄膜质量较差.溅射时间为90 min时,外加磁场前后AZO薄膜方阻分别为30.74?/和12.88?/.外加磁场对薄膜可见光透过率影响不大,但使薄膜的吸收边蓝移现象更明显.运用ansys软件对磁控溅射二维磁场分布模拟后发现,外加磁场提高了靶上方横向磁场强度,改善了磁场分布的均匀性,加强了磁场对电子的磁控作用,提高了靶电流,是AZO薄膜的溅射速率、光电性能和形貌结构得到提高和优化的原因.     

Optical and electrical properties of nanocrystal zinc oxide films prepared by dc magnetron sputtering at different sputtering pressures

The nanocrystal thin films of zinc oxide doped by Al (ZnO:Al) were deposited by dc reactive magnetron sputtering on the glass substrates, in the pressure range of 33-51 Pa. From the X-ray diffraction patterns, the nanocrystalline structure of ZnO:Al films and the grain size were determined. The optical transmission spectra depend from the sputtering pressure, but their average value was 90% in the range from 33 Pa to 47 Pa. Also, the sputtering pressure changes the optical band gap of ZnO:Al films, which is highest for films deposited at 37 Pa, 40 Pa and 47 Pa. The obtained films at room temperature have a sheet resistance of 190 Ω/cm² which increases with time, but the films annealed at temperature of 400 °C have constant resistance. The surface morphology of the films was studied by Scanning electron microscopy. XPS spectra showed that the peak of O1s of the as-deposited films is smaller than the peak of the annealed ZnO:Al films.     

The influence of titanium on the properties of zinc oxide films deposited by radio frequency magnetron sputtering

TiO₂-doped zinc oxide thin films were deposited on glass substrates by radio frequency (RF) magnetron sputtering with TiO₂-doped ZnO targets in an argon atmosphere. The structural properties of TiO₂-doped ZnO films doped with different TiO₂ contents were investigated. The experimental results show that polycrystalline TiO₂-doped ZnO films had the (0 0 2) preferred orientation. The deposition parameters such as the working pressure and substrate temperature of TiO₂-doped ZnO films were also investigated. The crystalline structure of the TiO₂-doped ZnO films gradually improved as the working pressure was lowered and the substrate temperature was raised. The lowest electrical resistivity for the TiO₂-doped ZnO films was obtained when the Ti addition was 1.34 wt%; its value was 2.50 × 10⁻³ Ω cm, smaller than that found in previous studies. The transmittance of the TiO₂-doped ZnO films in the visible wavelength range was more than 80%. The optical energy gap was related to the carrier concentration, and was in the range of 3.30-3.48 eV.     

直流反应磁控溅射制备掺铟ZnO透明导电薄膜的研究

本文介绍了掺铟ZnO透明导电膜的制备工艺.并应用半导体物理理论分析了薄膜的导电机理,用Drude理论建立了物理模型,分析与计算了薄膜从可见到红外光波段的光学性能,结果表明,理论计算与实测值两者符合得较好.     

A study of the optical properties of titanium oxide films prepared by dc reactive magnetron sputtering

TiO₂ thin films were deposited on the glass substrates by dc reactive magnetron sputtering technique at different sputtering pressures (2 × 10⁻³ to 2 × 10⁻² mbar). The films prepared at low pressures have an anatase phase, and the films prepared at high pressures have an amorphous phase. The optical properties were studied by measuring the transmittance and the ellipsometric spectra. The optical constants of the films in the visible range were obtained by fitting the transmittance combined with the ellipsometry measurements using the classical model with one oscillator. The refractive index of the films decreases from 2.5 until 2.1 as the sputtering pressure increases from 2 × 10⁻³ to 2 × 10⁻² mbar. The films prepared at the pressure higher than 6 × 10⁻³ mbar show a volume inhomogeneity. This volume inhomogeneity has been calculated by fitting the transmittance and the ellipsometric spectra. The volume inhomogeneity of the film prepared at the highest sputtering pressure is about 10%. Although the films prepared at high pressures show a large volume inhomogeneity, they have low extinction coefficients. It is suggested that the anatase phase results in more light scattering than amorphous phase does, and then a high extinction coefficient.     

The properties of transparent conducting molybdenum-doped ZnO films grown by radio frequency magnetron sputtering

Transparent conducting molybdenum-doped zinc oxide films are prepared by radio frequency(RF) magnetron sputtering at ambient temperature.The MoO3 content in the target varies from 0 to 5 wt%,and each film is polycrystalline with a hexagonal structure and a preferred orientation along the c axis.The resistivity first decreases and then increases with the increase in MoO3 content.The lowest resistivity achieved is 9.2 × 10-4.cm,with a high Hall mobility of 30 cm2.V-1.s-1 and a carrier concentration of 2.3×1020 cm-3 at an MoO3 content of 2 wt%.The average transmittance in the visible range is reduced from 91% to 80% with the increase in the MoO3 content in the target.     

Structural and electrical properties of fluorine-doped zinc tin oxide thin films prepared by radio-frequency magnetron sputtering

Transparent and conductive thin films of fluorine doped zinc tin oxide (FZTO) were deposited on glass substrates by radio-frequency (RF) magnetron sputtering using a 30 wt% ZnO with 70 wt% SnO₂ ceramic targets. The F-doping was carried out by introducing a mixed gas of pure Ar, CF₄, and O₂ forming gas into the sputtering chamber while sputtering ZTO target. The effect of annealing temperature on the structural, electrical and optical performances of FZTO thin films has been studied. FZTO thin film annealed at 600 °C shows the decrease in resistivity 5.47 × 10⁻³ Ω cm, carrier concentration ∼10¹⁹ cm⁻³, mobility ∼20 cm² V⁻¹ s⁻¹ and an increase in optical band gap from 3.41 to 3.60 eV with increasing the annealing temperatures which is well explained by Burstein–Moss effect. The optical transmittance of FZTO films was higher than 80% in all specimens. Work function (ϕ) of the FZTO films increase from 3.80 eV to 4.10 eV through annealing and are largely dependent on the amounts of incorporated F. FZTO is a possible potential transparent conducting oxide (TCO) alternative for application in optoelectronics.     

射频磁控溅射制备氧化钒薄膜的研究

氧化钒（VOx）薄膜是一种广泛应用于红外热成像探测的薄膜材料,研究VOx薄膜的制备工艺、获取高电阻温度系数（TCR）的VOx薄膜具有重要意义。以高纯金属钒作靶材,采用射频磁控溅射的方法在室温下制备了VOx薄膜。主要研究了氩氧流量比以及功率等工艺参数对薄膜TCR的影响,获得了较好的工艺参数。采用万用表和X射线光电子能谱仪（XPS）分别测试了不同条件下射频磁控溅射法制备的VOx薄膜的电阻特性和薄膜成分,测试结果表明,采用所获得的较好工艺参数制备的VOx薄膜TCR值大于1.8%。     

Low temperature deposition of transparent conducting ITO/Au/ITO films by reactive magnetron sputtering

Transparent conducting indium tin oxide/Au/indium tin oxide (ITO) multilayered films were deposited on unheated polycarbonate substrates by magnetron sputtering. The thickness of the Au intermediated film varied from 5 to 20 nm. Changes in the microstructure, surface roughness and optoelectrical properties of the ITO/Au/ITO films were investigated with respect to the thickness of the Au intermediated layer. X-ray diffraction measurements of ITO single layer films did not show characteristic diffraction peaks, while ITO/Au/ITO films showed an In₂O₃ (2 2 2) characteristic diffraction peak. The optoelectrical properties of the films were also dependent on the presence and thickness of the Au thin film. The ITO 50 nm/Au 10 nm/ITO 40 nm films had a sheet resistance of 5.6 Ω/□ and an average optical transmittance of 72% in the visible wavelength range of 400-700 nm. Consequently, the crystallinity, which affects the optoelectrical properties of ITO films, can be enhanced with Au intermediated films.     

Investigation of chemical mechanical polishing of zinc oxide thin films

Zinc oxide has become an important material for various applications. Commercially available zinc oxide single crystals and as-grown zinc oxide thin films have high surface roughness which has detrimental effects on the growth of subsequent layers and device performance. A chemical mechanical polishing (CMP) process was developed for the polishing of zinc oxide polycrystalline thin films. Highly smooth surfaces with RMS roughness <6 Å (as compared to the initial roughness of 26 ± 6 Å) were obtained under optimized conditions with removal rates as high as 670 Å/min. Effects of various CMP parameters on removal rate and surface roughness were evaluated. The role of pH on the polishing characteristics was investigated in detail.     

Growth of transparent conducting nano-structured In doped ZnO thin films by pulsed DC magnetron sputtering

Transparent conducting nano-structured In doped zinc oxide (IZO) thin films are deposited on corning 7059 glass substrates by bipolar pulsed DC magnetron sputtering with variation of pulsed frequency and substrate temperature. Highly c-axis oriented IZO thin films were grown in perpendicular to the substrate on the 30 kHz and 500 °C. The IZO films exhibited surface roughness of 3.6 nm similar to the commercial ITO and n-type semiconducting properties with electrical resistivity (carrier mobility) of about 5 × 10⁻³ Ω cm (14 cm²/V s). The optical characterization showed high transmittance of over 85% in the UV-vis region and exhibited the absorption edge of near 350 nm. In micro-Raman spectra, the origin of two additional modes is attributed to the host lattice defect due to the addition of In dopant. These results suggest that the IZO film can possibly be applied to make transparent conducting electrodes for flat panel displays.     

Low-temperature deposition of transparent conducting ZnO:Zr films on PET substrates by DC magnetron sputtering

Transparent conducting zirconium-doped zinc oxide (ZnO:Zr) films were firstly deposited on polyethylene terephthalate (PET) substrates with ZnO buffer layers by DC magnetron sputtering at room temperature. Dependence of physical properties of ZnO:Zr films on deposition pressure was systematically studied. All the deposited films were polycrystalline and (1 0 0) oriented. When deposition pressure increases from 1 to 2.5 Pa, the crystallinity of the films improves and the resistivity decreases. While deposition pressure increases from 2.5 to 3.5 Pa, the crystallinity of the films deteriorates and the resistivity increases. The lowest resistivity of 1.8 × 10⁻³ Ω cm was obtained for the films deposited at the optimum deposition pressure of 2.5 Pa. All the films present a high transmittance of above 86% in the wavelength range of the visible spectrum.     

Transparent conducting molybdenum-doped zinc oxide films deposited by RF magnetron sputtering

A new transparent conducting oxide (TCO) film with low resistivity and high transmittance in the visible range, molybdenum-doped zinc oxide (MZO), was successfully prepared by RF magnetron sputtering method on glass substrates at room temperature. The structural, electrical, and optical properties as a function of film thickness were investigated. All the samples have a preferred orientation with the (0 0 2) planes parallel to the substrates. The resistivity initially decreases and then shows an increase with the increase of the film thickness. When the thickness is 400 nm, the film has its best crystallinity and lowest resistivity 9.2 × 10⁻⁴ Ω cm with a Hall mobility of 30 cm² V⁻¹ s⁻¹ and a carrier concentration of 2.3 × 10²⁰ cm⁻³. The average transmittance in the visible range exceeds 84% for all thickness films.     

Room-temperature deposition of transparent conducting Al-doped ZnO films by RF magnetron sputtering method

Transparent conductive Al-doped zinc oxide (AZO) films with highly (0 0 2)-preferred orientation were deposited on quartz substrates at room temperature by RF magnetron sputtering. Optimization of deposition parameters was based on RF power, Ar pressure in the vacuum chamber, and distance between the target and substrate. The structural, electrical, and optical properties of the AZO thin films were investigated by X-ray diffraction, Hall measurement, and optical transmission spectroscopy. The 250 nm thickness AZO films with an electrical resistivity as low as 4.62 × 10⁻⁴ Ω cm and an average optical transmission of 93.7% in the visible range were obtained at RF power of 300 W, Ar flow rate of 30 sccm, and target distance of 7 cm. The optical bandgap depends on the deposition condition, and was in the range of 3.75-3.86 eV. These results make the possibility for light emitting diodes (LEDs) and solar cells with AZO films as transparent electrodes, especially using lift-off process to achieve the transparent electrode pattern transfer.     

Study of microstructure and nanomechanical properties of Zr films prepared by pulsed magnetron sputtering

The present work studies the effect of substrate temperature on the growth characteristics of zirconium films prepared by pulsed magnetron sputtering. Formation of α-phase of zirconium was observed in the temperature range 300-873 K. X-ray diffraction of Zr films revealed predominantly [0 0 1] texture. It is noticed that crystallite size increases with increasing substrate temperature. Hexagonal shaped crystallites seem to grow along the surface normal of the substrate for the films deposited at 773 K. Nanoindentation measurements showed that the hardness of the films is in the range 6-10 GPa. The scratch test indicated that the films deposited at higher substrate temperatures had excellent bonding with the substrate and no significant critical failure was noticed up to an applied load of 20 N.     

Ultra smooth NiO thin films on flexible plastic (PET) substrate at room temperature by RF magnetron sputtering and effect of oxygen partial pressure on their properties

Transparent p-type nickel oxide thin films were grown on polyethylene terephthalate (PET) and glass substrates by RF magnetron sputtering technique in argon + oxygen atmosphere with different oxygen partial pressures at room temperature. The morphology of the NiO thin films grown on PET and glass substrates was studied by atomic force microscope. The rms surface roughnesses of the films were in the range 0.63-0.65 nm. These ultra smooth nanocrystalline NiO thin films are useful for many applications. High resolution transmission electron microscopic studies revealed that the grains of NiO films on the highly flexible PET substrate were purely crystalline and spherical in shape with diameters 8-10 nm. XRD analysis also supported these results. NiO films grown on the PET substrates were found to have better crystalline quality with fewer defects than those on the glass substrates. The sheet resistances of the NiO films deposited on PET and glass substrates were not much different; having values 5.1 and 5.3 kΩ/□ and decreased to 3.05, 3.1 kΩ/□ respectively with increasing oxygen partial pressure. The thicknesses of the films on both substrates were ∼700 nm. It was also noted that further increase in oxygen partial pressure caused increase in resistivity due to formation of defects in NiO.     

化学水浴法和磁控溅射法制备硫化镉薄膜的性能研究

以氯化铵、氯化镉、氢氧化钾和硫脲为反应物采用化学水浴法制备了硫化镉薄膜,为了作对比研究,采用射频磁控溅射以硫化镉为靶材,氩气为溅射气体,制备了硫化镉薄膜。采用X射线衍射、扫描电子显微镜和紫外-可见光光谱仪分别表征了硫化镉薄膜的结构、形貌和光学吸收特性。结果表明,采用以上两种方法制备的硫化镉均具有(002)择优取向,溅射法制备的硫化镉薄膜较致密,薄膜表面较光滑,平均晶粒尺寸在20～30nm;水浴法制备的硫化镉薄膜颗粒尺寸较小,缺陷较多。除了在短波段溅射所得硫化镉薄膜的透过率略差于水浴法所得硫化镉薄膜之外,溅射法制备的硫化镉薄膜的性能整体上优于水浴法制备的薄膜。两种方法制备的硫化镉薄膜的能隙在2.3～2.5eV。     

Deposition and properties of B-N codoped p-type ZnO thin films by RF magnetron sputtering

B-N codoped p-type ZnO thin films have been realized by radio frequency (rf) magnetron sputtering using a mixture of argon and oxygen as sputtering gas. Types of conduction and electrical properties in codoped ZnO films were found to be dependent on oxygen partial pressure ratios in the sputtering gas mixture. When oxygen partial pressure ratio was 70%, the codoped ZnO film showed p-type conduction and had the best electrical properties. Additionally, the p-ZnO/n-Si heterojunction showed a clear p-n diode characteristic. XRD results indicate that the B-N codoped ZnO film prepared in 70% oxygen partial pressure ratio has high crystal quality with (0 0 2) preferential orientation. Meanwhile, the B-N codoped ZnO film has high optical quality and displays the stronger near band edge (NBE) emission in the temperature-dependent photoluminescence spectrum, the acceptor energy level was estimated to be located at 125 meV above the valence band.