Sensing low concentrations of CO using flame-spray-made Pt/SnO2 nanoparticles

Tin dioxide nanoparticles of different sizes and platinum doping contents were synthesized in one step using the flame spray pyrolysis (FSP) technique. The particles were used to fabricate semiconducting gas sensors for low level CO detection, i.e. with a CO gas concentration as low as 5 ppm in the absence and presence of water. Post treatment of the SnO₂ nanoparticles was not needed enabling the investigation of the metal oxide particle size effect. Gas sensors based on tin dioxide with a primary particle size of 10 nm showed signals one order of magnitude higher than the ones corresponding to the primary particle size of 330 nm. In situ platinum functionalization of the SnO₂ during FSP synthesis resulted in higher sensor responses for the 0.2 wt% Pt-content than for the 2.0 wt% Pt. The effect is mainly attributed to catalytic consumption of CO and to the associated reduced sensor response. Pure and functionalized tin dioxide nanoparticles have been characterized by Brunauer, Emmett and Teller (BET) surface area determination, X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy (STEM) while the platinum oxidation state and dispersion have been investigated by X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS). The sensors showed high stability (up to 20 days) and are suitable for low level CO detection: <10 ppm according to European and 50 ppm according to US legislation, respectively.     

Characterization of Ag nanoparticles on Si wafer prepared using Tollen's reagent and acid-etching

Ag nanoparticles on SiO₂/Si surfaces synthesized using the Tollen's reagent and a subsequent acid-etching were characterized using X-ray photoelectron spectroscopy (XPS). Combining the reduction of the Tollen's reagent and the chemical etching, one can create naked Ag nanoparticles with various sizes in the size range below ∼10 nanometers (nm). The reduced particle size by the chemical etching was identified using positive core level shifts with increasing etching time. Ag nanoparticles smaller than ∼3 nm undergo a reversible oxidation and reduction cycle by reacting with H₂O₂/H₂O and a subsequent heating under vacuum to 150 °C, which was not found for the bulk counterparts and larger particles, demonstrating unique chemical properties of nanoparticles compared to the bulk counterparts.     

Synthesis of magnetite nanoparticles via a solvent-free thermal decomposition route

Superparamagnetic nanoparticles have been widely applied in various bio-medical applications. To date, it is still a challenge to synthesize nanosized Fe₃O₄ particles with controlled size and distribution. In this paper, a novel solvent-free thermal decomposition method is reported for synthesizing Fe₃O₄ nanoparticles. Size and morphology of the nanoparticles are determined by TEM while the structure of the nanoparticles is identified by FTIR, XPS and TGA measurements. Magnetic properties of the obtained particles are determined using VSM and SQUID measurement. The particle size of the Fe₃O₄ can be tailored by adjusting either reaction temperature or time. When the reaction temperature is increased to 330 °C and the reaction time is extended to 4 h, the average particle size of the obtained nanoparticles is ∼9 nm, while Ms value reaches ∼76 emu/g. The as synthesized Fe₃O₄ nanoparticles show well-established superparamagnetic properties with the blocking temperature at around 100 K.     

A study of modified Fe3O4 nanoparticles for the synthesis of ionic ferrofluids

XRD and XPS analyses revealed that a Fe(NO₃)₃·9H₂O layer formed outside γ-Fe₂O₃ particles when Fe₃O₄ nanoparticles were treated with ferric nitrate. The particle density differed for untreated and treated particles and was not uniform for the latter. The specific saturation magnetization of both treated and untreated particles was used to estimate the thickness of the Fe(NO₃)₃·9H₂O layer and the average density of the treated particles. The density of the treated particles was used to calculate the density of ferrofluids of different particle volume fractions. These values are in agreement with measured results. Therefore, the particle volume fraction can be designed to synthesize acid ionic ferrofluids based on Fe₃O₄ nanoparticles using Massart's method.     

One-pot synthesis of amphiphilic superparamagnetic FePt nanoparticles and magnetic resonance imaging in vitro

Monodispersed amphiphilic FePt nanoparticles with the diameter of about 4 nm were synthesized by high temperature pyrolysis of iron(III) acetylacetonate and platinum(II) acetylacetonate. Their amphiphilicity is contributed to the tetraethylene glycol (TEG) and oleic acid (OA) on the surface, which is confirmed by FTIR and XPS spectra. They provide a superparamagnetic property with the saturation magnetization (Ms) of about 25 emu/g and the transverse relaxivity (r₂) of about 122.6 mM⁻¹ s⁻¹ in aqueous solutions. Furthermore, FePt nanoparticles show low cytotoxicity in living cells. They can be uptaken by HeLa cells effectively and result in the obvious decrease of T₂ relaxation time after internalization.     

Particle size effect on phase and magnetic properties of polymer-coated magnetic nanoparticles

Polymer-coated magnetic nanoparticles are hi-tech materials with ample applications in the field of biomedicine for the treatment of cancer and targeted drug delivery. In this study, magnetic nanoparticles were synthesized by chemical reduction of FeCl₂ solution with sodium borohydride and coated with amine-terminated polyethylene glycol (aPEG). By varying the concentration of the reactants, the particle size and the crystallinity of the particles were varied. The particle size was found to increase from 6 to 20 nm and the structure becomes amorphous-like with increase in the molar concentration of the reactant. The magnetization at 1 T field (M_1T) for all samples is > 45 emu/g while the coercivity is in the range of 100-350 Oe. When the ethanol-suspended particles are subjected to an alternating magnetic field of 4 Oe at 500 kHz, the temperature is increased to a maximum normalized temperature (3.8 °C/mg) with decreasing particle size.     

Nanocomposites of magnetic cobalt nanoparticles and cellulose

Polymeric matrices with stabilized metallic nanoparticles constitute an important class of nanostructured materials, because polymer technology allows fabrication of components with various electronic, magnetic and mechanical properties. The porous cellulose matrix has been shown to be a useful support material for platinum, palladium, silver, copper and nickel nanoparticles. In the present study, nanosized cobalt particles with enhanced magnetic properties were made by chemical reduction within a microcrystalline cellulose (MCC) matrix. Two different chemical reducers, NaBH₄ and NaH₂PO₂, were used, and the so-formed nanoparticles were characterized with X-ray absorption spectroscopy, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. These experimental techniques were used to gain insight into the effect of different synthesis routes on structural properties of the nanoparticles. Magnetic properties of the nanoparticles were studied using a vibrating sample magnetometer. Particles made via the NaBH₄ reduction were amorphous Co-B or Co oxide composites with diminished ferromagnetic behaviour and particles made via the NaH₂PO₂ reduction were well-ordered ferromagnetic hcp cobalt nanocrystals.     

The investigation of oxidized silver nanoparticles prepared by thermal evaporation and radio-frequency sputtering of metallic silver under oxygen

The investigation of oxidized silver nanoparticles by the photoemission (XPS, UPS) and HRTEM methods was performed. The nanoparticles of oxidized silver were obtained in the vacuum chamber by two methods of synthesis: thermal evaporation of silver nanoparticles followed by transferring in convective gas flow and sputtering of oxidized clusters under the action of plasma. Both methods indicated that oxygen interaction with silver nanoparticles depends strongly on its size. It was shown that the chemical bonding of oxygen species stabilized on small particles differs from the oxygen species adsorbed on bulk silver surfaces (monocrystals, foils and large particles). The low charged oxygen with molecular type of bonding stabilizes on particles of size approximately 5 nm and smaller. Increasing particle size leads to the dissociation of molecular oxygen species and the formation of strongly charged oxygen composed of oxide nanoparticles like Ag₂O or AgO type. The presence of extended defects in the microdomain large nanoparticles facilitates the formation of Ag₂O or AgO layers covering metallic nanosilver.     

Preparation of nanocrystalline Sn-TiO2−X via a rapid and simple stannous chemical reducing route

The Sn-TiO_2−X nanoparticles have been prepared via a rapid and simple stannous chemical reducing method. The as-prepared Sn-TiO_2−X nanoparticles were investigated by means of surface photovoltage spectroscopy (SPS), XPS, and DRS technology as well as photocatalytic degradation of RhB were studied under illumination. The experiment results revealed that the reduction of the TiO₂ particles raised their Fermi level, which can enhance the driven force of photoinduced electrons transferring from TiO₂ to adsorbed O₂ and SnO₂ on the surface of TiO₂. On the other hand, the amount of oxygen vacancies of the Sn-TiO_2−X increased after the stannous chemical reduction. The oxygen vacancies can also effectively inhibit the recombination of photoinduced electrons and holes pairs. These factors are favorable to the photocatalytic reaction.     

Combined spectroscopy and microscopy of supported MoS2 nanoparticles

Supported molybdenum-sulfide nanoparticles are known catalysts for petroleum hydrodesulfurization as well as for electrochemical hydrogen evolution. In this study, we investigate molybdenum-sulfide nanoparticles supported on Au(1 1 1) using X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM), aiming to correlate spectroscopically determined chemical states with atomically resolved nanostructure. The results of this study allow us to conclude the following: (1) the XPS results from our model system are in good agreement with previously published results on supported MoS₂ for industrial applications, validating in part the fidelity of the model system; (2) STM reveals that catalytically active, crystalline MoS₂ nanoparticles exhibiting the well-known metallic edge state are only present after a post-deposition annealing step in the synthesis procedure, without which the particles exhibit amorphous shapes and incomplete sulfidation; and (3) the sulfided nanoparticles are found to be stable in air at room temperature.     

Hydrothermal synthesis of well-dispersed ultrafine N-doped TiO2 nanoparticles with enhanced photocatalytic activity under visible light

Ultrafine nitrogen-doped TiO₂ nanoparticles with narrow particle size distribution, good dispersion, and high surface area were synthesized in the presence of urea and PEG-4000 via a hydrothermal procedure. TEM observation, N₂ adsorption, XRD, UV-vis spectroscopy, the Raman spectroscopy and XPS analysis were conducted to characterize the synthesized TiO₂ particles. The synthesized TiO₂ particles were a mixture of 49.5% anatase and 50.5% rutile with a size of around 5 nm. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive Brilliant Blue KN-R under both UV and visible light. The synthesized TiO₂ particles showed much higher photocatalytic activity than a commercial P25 TiO₂ powder under both UV and visible light irradiations. The high performance is associated to N doping, the reduced particle size, good dispersion, high surface area, and a quantum size effect.     

Nanocrystalline CoSn2-carbon composite electrode prepared by using sonochemistry

A sonochemical method has been used to prepare negative electrode materials containing intermetallic nanoparticles and polyacrylonitrile (PAN). The ultrasound irradiation is applied to achieve small particle size. After annealing at 490 °C under Ar-flow, the polymer PAN is partially carbonized and the metallic nanoparticles are surrounded by a carbonaceous matrix. The main metallic phase is CoSn₂. The carbonaceous coating and the surface oxides have been explored by using XPS. The resulting CoSn₂-carbonaceous phase electrode (CoSn₂@C) shows improved electrochemical behavior (ca. 450 mAh/g after 50 cycles) in comparison with previous reports on pure crystalline CoSn₂. The reaction between CoSn₂@C and Li has been studied by using XRD and ¹¹⁹Sn Mössbauer spectroscopy. The formation of large grains of crystalline Li_xSn phases after the first discharge is discarded. The small particle size which is achieved by using ultrasonication and the carbonaceous matrix contribute to maintain the Co-Sn interactions during the electrochemical cycling. The aggregation of the nanosized metallic particles upon electrochemical cycling can be suppressed by the carbonaceous matrix (pyrolytic PAN).     

Recovery of iron/iron oxide nanoparticles from solution: comparison of methods and their effects

Most methods currently being used to recover Fe⁰-core/oxide-shell nanoparticles from solutions (including the solvents they are synthesized or stored in) are potentially problematic because they may alter the particle composition (e.g., depositing salts formed from solutes) or leave the particles prone to transformations during subsequent storage and handling (e.g., due to residual moisture). In this study, several methods for recovery of nanoparticles from aqueous solution were studied to determine how they affect the structure and reactivity of the recovered materials. Simple washing of the nanoparticles during vacuum filtration (i.e., “flash drying”) can leave up to ~17 wt% residual moisture. Modeling calculations suggest this moisture is mostly capillary or matric water held between particles and particle aggregates, which can be removed by drying for short periods at relative vapor pressures below 0.9. Flash drying followed by vacuum drying, all under N₂, leaves no detectable residue from precipitation of solutes (detectable by X-ray photoelectron spectroscopy, XPS), no significant changes in overall particle composition or structure (determined by transmission electron microscopy, TEM), and negligible residual moisture (by thermogravimetric analysis, TGA). While this improved flash-drying protocol may be the preferred method for recovering nanoparticles for many purposes, we found that Fe⁰-core/oxide-shell nanoparticles still exhibit gradual aging during storage when characterized electrochemically with voltammetry.     

Particle size dependence of relaxivity for silica-coated iron oxide nanoparticles

We investigate the particle size dependence of the relaxivity of hydrogen protons in an aqueous solution of iron oxide (Fe₃O₄) nanoparticles coated in silica for biocompatibility. The T₁ and T₂ relaxation times for various concentrations of silica-coated nanoparticles were determined by a magnetic resonance scanner. We find that the relaxivity increased linearly with increasing particle size. The T₂ relaxivity (R₂) is more than 50 times larger than the T₁ relaxivity (R₁) for the nanoparticle contrast agent, which reflects the fact that the T₂ relaxation is mainly influenced by outer sphere processes. The high R₂/R₁ ratio demonstrates that silica-coated iron oxide nanoparticles may serve as a T₂ contrast agents in magnetic resonance imaging with high efficacy.     

Modification of functionalized mesoporous silica on the formation and the catalytic performance of platinum nanocatalysts

Several functionalized mesoporous silicas (MCM-41 and SBA-15 terminated with amino groups by multistep graft) are prepared and used as carriers for platinum nanoparticles. Modification of the grafted molecules is investigated on the component of the silicas and the formation of nanoparticles. Catalytic performance of the loaded platinum nanocatalysts is tested on selective hydrogenation of ortho-chloronitrobenzene (o-CNB). Results indicate that SBA-15 can be grafted with more amino groups than MCM-41. In most cases, small quantity of platinum precursor benefits the formation of small platinum nanoparticles on the functionalized silicas. The platinum nanocatalysts loaded on the one-step grafted silicas hold better catalytic activity and slightly lower selectivity to ortho-chloroaniline (o-CAN) than those loaded on the two-step grafted silicas. Besides the advantage of reuse, the loaded platinum catalysts on the functionalized silicas have similar catalytic property as the colloidal platinum nanocatalysts.     

A corrosion-resistance superhydrophobic TiO2 film

A superhydrophobic TiO₂ film with water contact angle greater than 170° on Hastelloy substrate was fabricated through simply dip-coating method from TiO₂ precursor solution containing TiO₂ nanoparticles with the average diameter 25 nm, followed by heat-treatment and modification with fluoroalkylsilane (FAS) molecules. The as-obtained sample was characterized by scanning electron microscopy (SEM), X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS), and water contact angle measurement respectively. Moreover, the dynamic light scattering (DLS) size distribution of TiO₂ aggregated particles in the TiO₂ precursor solution containing P25 particles was evaluated by Laser Particle Sizer. It is found that the TiO₂ nanoparticles in TiO₂ precursor solution play a crucial role to form high superhydrophobicity. Simultaneously, the superhydrophobic TiO₂ film still showed great superhydrophobicity after corroded with strong acid or alkali solutions and protected the substrate from corrosion which should be critical to the potential application in industry.     

Fabrication of platinum particles by intense, femtosecond laser pulse irradiation of aqueous solution

Platinum nano-particles were directly fabricated through molecular dissociation process induced by tightly focused femtosecond laser pluses in hydrogen hexachloroplatinate (IV) hexahydrate (H₂PtCl₆·6H₂O) aqueous solution. After irradiation, it was found that UV-visible absorption spectrum of the solution was changed and a large number of small platinum particles were synthesized. The variation of absorbance in the spectrum and the yield the particle synthesis depended on the concentration of the solution. The most effective condition for particle synthesis was 0.1 wt%. Black precipitates of platinum particles were observed in the bottom of the vessel after irradiation in some cases. The dispersibility of the particles was greatly improved by the addition of polyvinylpyrrolidone (PVP) as a dispersant, and no precipitates were found in the solution with 1.0 × 10⁻² wt% PVP. Consequently, highly monodispersed platinum nano-particles with the mean size of about 3 nm were successfully fabricated.     

Investigation of nanoparticulate silicon as printed layers using scanning electron microscopy,transmission electron microscopy,X‐ray absorption spectroscopy and X‐ray photoelectron spectroscopy

The presence of native oxide on the surface of silicon nanoparticles is known to inhibit charge transport on the surfaces. Scanning electron microscopy (SEM) studies reveal that the particles in the printed silicon network have a wide range of sizes and shapes. High‐resolution transmission electron microscopy reveals that the particle surfaces have mainly the (111)‐ and (100)‐oriented planes which stabilizes against further oxidation of the particles. X‐ray absorption spectroscopy (XANES) and X‐ray photoelectron spectroscopy (XPS) measurements at the O 1s‐edge have been utilized to study the oxidation and local atomic structure of printed layers of silicon nanoparticles which were milled for different times. XANES results reveal the presence of the +4 (SiO₂) oxidation state which tends towards the +2 (SiO) state for higher milling times. Si 2p XPS results indicate that the surfaces of the silicon nanoparticles in the printed layers are only partially oxidized and that all three sub‐oxide, +1 (Si₂O), +2 (SiO) and +3 (Si₂O₃), states are present. The analysis of the change in the sub‐oxide peaks of the silicon nanoparticles shows the dominance of the +4 state only for lower milling times.     

Doping effect of Ag nanoparticles on critical current of YBa2Cu3O7−δ bulk superconductor

The objective of this work is to investigate the effect of Ag nanoparticles on critical current of YBa₂Cu₃O_7?δ (YBCO) superconductor. Ag nanoparticles with different particle sizes from 30 to 1000 nm were prepared through the chemical reduction of AgNO₃ in an alcohol solution. Then, samples of YBCO superconductors were doped by 1 and 2 wt.% of Ag nanoparticles with different sizes. Samples were characterized with XRD, SEM and EDX measurements. Critical current measurements were performed using a standard four-probe technique at liquid nitrogen temperature. The results showed by increasing of Ag nanoparticles up to 700 nm the J_c increases, but decreases by further increase in Ag particles size. The critical current enhancement is attributed to the improved connectivity between the grain boundaries and better crystallization of the grains.     

Application of X-ray photoelectron spectroscopy to characterization of Au nanoparticles formed by ion implantation into SiO2

In X-ray photoelectron spectroscopy (XPS) of Au nanoparticles, the width of 5d valence band changes with Au particle size. This enables us to estimate the size of Au nanoparticles by using XPS. In this work, the 5d-band width has been measured for Au nanoparticles formed by ion implantation into SiO₂. The 5d-band width is found to be correlated strongly with the Au concentration. As the Au concentration increases, the 5d-band width becomes larger, indicating that the Au nanoparticles with the larger size tend to be formed in the vicinity of the projected range of Au ions. This correlation agrees very well with the results from transmission electron microscopy.