Orthogonal fs/ns double-pulse libs for copper-based-alloy analysis

The analytical response of a fs/ns double-pulse laser induced breakdown spectroscopy technique based on the orthogonal reheating induced by a ns-laser pulse on a fs-laser ablation plume is presented. All investigations have been performed in air at atmospheric pressure and employing certified copper-based-alloy targets. The emission intensities of the considered electronic transitions of Pb(I), Sn(I) and Zn(I) have been normalised with a Cu(I) emission line intensity belonging to the same considered spectral range. Emission data, acquired with inter-pulse steps of 2 μs within the delay range of 1–200 μs, have shown that fractionation takes place. Nevertheless, excellent linear regression coefficients (0.998–0.999), despite the target’s large compositional variation and fractionation effects, have been obtained by integrating all emission intensity data along the whole inter-pulse delays used. Deviations from the theoretical ratio of the Zn(I)/Cu(I) emission intensities are shown and some hypotheses about the processes involved are formulated.     

fs/ns dual-pulse LIBS analytic survey for copper-based alloys

The quantitative analytic capability of a fs/ns dual-pulse Laser-Induced Breakdown Spectroscopy technique, based on the orthogonal reheating of a fs-laser ablation plume by a ns-laser pulse, is presented. In this work, it is shown how the effect played by the delay times between the two laser beams can vary the analytical response of this dual-pulse LIBS configuration. In order to address this task, the Sn, Pb and Zn calibration curves of five certified copper-based samples have been investigated. These calibration curves have been obtained, in air at atmospheric pressure, by integrating the emission data collected in two different inter-pulse delay zones, one in the delay interval of 1-41 μs, the other within the range of 46-196 μs. For drawing the species calibration curves, the emission intensities of the considered Pb(I), Sn(I) and Zn(I) electronic transitions have been normalized with a non-resonant Cu(I) emission line. The experimental results have shown that, by varying the inter-pulse delay between the two laser beams, complementary analytical results can be induced. By considering at once all data acquired within the inter-pulse delay time of 1-196 μs, this hypothesis has been strengthened. The calibration curves obtained in this way are characterized by excellent linear regression coefficients (0.988-0.999) despite of the large Sn, Pb and Zn compositional variation of the targets employed. The results presented reveal, for the first time, that, by taking into account the role played by the inter-pulse delay time between the two laser beams, the fs/ns dual-pulse LIBS configuration here used can be improved and provide very good opportunities for performing quantitative analysis of copper-based alloys.     

ns- and fs-LIBS of copper-based-alloys: A different approach

A self-calibrated analytical technique, based on plasmas induced by either 250 fs or 7 ns laser pulses, is presented. This approach is comparable to other calibration-free methods based on LTE assumption. In order to apply this method to very different laser pulse durations, the partial-local thermodynamic equilibrium (p-LTE) has been considered within the energy range of 30,000-50,000 cm⁻¹. In order to obtain the neutral species densities, the detected plasma species emission lines intensities have been treated together with the experimental evaluated background black-body Planck-like emission distribution. For validating the followed method, three certified copper-based-alloys standards were employed and their minor components (Ni, Pb and Sn) amounts were determined. As a result, it arises, that this standardless method, independently from the laser source pulse durations, provides good quantitative analysis, and, consequently, that the composition of the plasma plume emitting species induced is not affected by the laser pulse time width.     

Optical emission spectroscopy investigation of an ultra-short laser induced titanium plasma reheated by a ns laser pulse

The dynamics of a titanium plasma species, induced in air by coupling a fs-ablating laser pulse with an orthogonal ns-reheating laser source placed at the fixed distance of 1.0 mm from the target surface, has been followed by temporally resolved emission spectroscopy. The temporal evolutions of plasma features such as excitation temperatures and electron densities have been evaluated by using two different laser energies of the first fs-ablating laser pulse (0.8 mJ and 3.0 mJ). Optimum inter-pulse delay times, experimentally determined, of 250 μs and 500 μs were used for the fs laser energy of 3.0 mJ and 0.8 mJ, respectively. By experimental inspections of the main plasma species electronic transitions so obtained, a strong enhancement was evaluated up to one and two orders of magnitude for Ti(I) and Ti(II), respectively. Independently from the fs laser energy employed, the plasma features showed the same temporal behaviour implying that the ns-reheating characteristics of this process belong to the reheating mechanism itself. The experimental results have been discussed and the excited species evolutions and elementary processes involved, as well as, the local thermodynamic equilibrium departures, have been outlined.     

Efficient generation of 200 mJ nanosecond pulses at 100 Hz repetition rate from a cryogenic cooled Yb:YAG MOPA system

A diode-pumped Master Oscillator Power Amplifier (MOPA) laser system based on cryogenic cooled Yb:YAG has been designed, developed and its output performance characterised. The laser system consists of a fibre oscillator, an active mirror regenerative amplifier and a four pass main amplifier. 2.4 mJ, 10 ns, 100 Hz seed pulses from the fibre oscillator/regenerative amplifier arrangement were amplified up to pulse energies of over 200 mJ by using the four pass main amplifier arrangement. As a further study we have obtained an increased slope efficiency of 40% and an optical-to-optical efficiency of 30% using a pinhole vacuum spatial filter/image relay for laser mode control. With 1.8 mJ input seed pulses, output pulse energies of around 150 mJ were achieved.     

LD end pumped, actively mode locked and passively Q-switched Nd:YAP laser at 1341 nm

An end pumped Nd:YAP laser at 1341 nm is actively mode locked and passively Q-switched. Pumping was done with a pulsed high power laser diode with maximum power 425 W. V³⁺:YAG with 61% initial transmission served as saturable absorber, and an acousto-optic modulator is used for active mode locking. The output pulse train with 69 ns duration has a total energy of 3.2 mJ with ±4% shot-to-shot fluctuation. The peak output energy of a single mode locked pulse is 0.25 mJ. The pulse duration of a single mode locked pulse is less than 800 ps. The output laser beam is nearly diffraction limited with 1.6 mm diameter, and beam propagation factor M² about 1.3.     

Effect of pulse width and fluence of femtosecond laser on the size of nanobump array

Conical nanobump arrays were generated on gold thin film processed by interfering femtosecond laser. The transition of the height and diameter as functions of fluence and pulse width was investigated. When the fluence was 87 mJ/cm², the height and diameter were not so different at 350 fs or shorter pulse width. They decreased at longer pulse width, and no bump could be generated over 1.6 ps. The results suggest the decrease of size is due to the diffusion of electron to not-excited region, and due to heat conduction to not heated region or substrate, or change of absorbance of laser. At long pulse width of 2.4 ps and relatively higher fluence of 190 mJ/cm², nanobump had liquid-like structure as a stop motion of a water drop.     

Comparison of the laser ablation process on Zn and Ti using pulsed digital holographic interferometry

Pulsed digital holographic interferometry has been used to compare the laser ablation process of a Q-switched Nd-YAG laser pulse (wavelength 1064 nm, pulse duration 12 ns) on two different metals (Zn and Ti) under atmospheric air pressure. Digital holograms were recorded for different time delays using collimated laser light (532 nm) passed through the volume along the target. Numerical data of the integrated refractive index field were calculated and presented as phase maps. Intensity maps were calculated from the recorded digital holograms and are used to calculate the attenuation of the probing laser beam by the ablated plume. The different structures of the plume, namely streaks normal to the surface for Zn in contrast to absorbing regions for Ti, indicates that different mechanisms of laser ablation could happen for different metals for the same laser settings and surrounding gas. At a laser fluence of 5 J/cm², phase explosion appears to be the ablation mechanism in case of Zn, while for Ti normal vaporization seems to be the dominant mechanism.     

1.3414 μm Nd:YAP pulse laser in Q-switched mode

In this paper, a flash-lamp pumped 1.3414 μm Nd:YAP Q-switched pulse laser are presented. The experimental results for about 45 ns of pulse duration and more than 300 mJ of output energy have been obtained and discussed.     

Analyses of surface coloration on TiO2 film irradiated with excimer laser

TiO₂ film of around 850 nm in thickness was deposited on a soda-lime glass by PVD sputtering and irradiated using one pulse of krypton-fluorine (KrF) excimer laser (wavelength of 248 nm and pulse duration of 25 ns) with varying fluence. The color of the irradiated area became darker with increasing laser fluence. Irradiated surfaces were characterized using optical microscopy, scanning electron microscopy, Raman spectroscopy and atomic force microscopy. Surface undergoes thermal annealing at low laser fluence of 400 and 590 mJ/cm². Microcracks at medium laser fluence of 1000 mJ/cm² are attributed to surface melting and solidification. Hydrodynamic ablation is proposed to explain the formation of micropores and networks at higher laser fluence of 1100 and 1200 mJ/cm². The darkening effect is explained in terms of trapping of light in the surface defects formed rather than anatase to rutile phase transformation as reported by others. Controlled darkening of TiO₂ film might be used for adjustable filters.     

Dynamics of ZnO laser produced plasma in high pressure argon

Pulsed laser deposition of ZnO in high pressure gas offers a route for the catalyst-free preparation of ZnO nanorods less than 10 nm in diameter. This paper describes the results of some experiments to investigate the laser plume dynamics in the high gas pressure (5 × 10³-10⁴ Pa) regime used for PLD of ZnO nanorods. In this regime the ablation plume is strongly coupled to the gas and the plume expansion is brought to a halt within about 1 cm from the target. A 248 nm excimer laser was used to ablate a ceramic ZnO target in various pressures of argon. Time- and space-resolved UV/vis emission spectroscopy and Langmuir probe measurements were used to diagnose the plasma and follow the plume dynamics. By measuring the spatial profiles of Zn I and Zn II spectral lines it was possible to follow the propagation of the external and internal shock waves associated with the interaction of the ablation plume with the gas. The Langmuir probe measurements showed that the electron density was 10⁹-10¹⁰ cm⁻³ and the electron temperature was several eV. At these conditions the ionization equilibrium is described by the collisional-radiative model. The plume dynamics was also studied for ZnO targets doped with elements which are lighter (Mg), comparable to (Ga), and heavier (Er) than Zn, to see if there is any elemental segregation in the plume.     

Development of a nearly transform-limited, low-repetition-rate, picosecond optical parametric generator

A low-repetition-rate (10-Hz), picosecond (ps) optical parametric generator (OPG) seeded at the idler wavelength with a high-power diode laser is demonstrated. The output of the OPG at ∼566 nm is amplified in dye cells, resulting in signal enhancement by more than three orders of magnitude. The nearly transform-limited beam at ∼566 nm has a pulsewidth of ∼170 ps, with an overall output of ∼2.3 mJ/pulse. The laser is tuned either by tuning the nonlinear crystal or the seed-laser current. The applications of such a simple, compact, high-performance, tunable ps laser system for linear and nonlinear spectroscopies are outlined.     

Diode-pumped, chirped-pulse Yb:S-FAP regenerative amplifier for laser-Compton X-ray generation

We present a diode-pumped, chirped-pulse Yb:S-FAP regenerative amplifier. This regenerative amplifier was developed as a first amplifier in an all-solid-state Yb:S-FAP laser system for laser-Compton X-ray generation. The amplifier delivers pulse energies above 24 mJ at a repetition rate of 50 Hz. Pulse compression reduces pulse widths to approximately 2.0 ps.     

Propagation of LaMnO3 laser ablation plume in oxygen gas

The propagation of LaMnO₃ laser ablation plume in oxygen background has been investigated using fast photography of overall visible plume emission and time-resolved optical emission spectroscopy. The plume expansion was studied with ambient oxygen pressures ranging from vacuum level to 100 Pa. Free-expansion, splitting, sharpening and stopping of the plume were observed at different pressures and time delays after the laser pulse. Time-resolved optical emission spectroscopy showed that oxides are mainly formed through reaction of the atomic species ablated from the target with oxygen in the gas-phase. These reactions mainly affect the content of lanthanum oxide in the plume, while emission of manganese oxide is barely observed in all the range of pressure investigated.     

Laser-excited spectra of Lu2SiO5:Ce scintillator

The emission spectra of Lu₂SiO₅:Ce single crystal under the excitation of 266 nm laser were investigated. The emission spectra of LSO single crystal show no temperature quenching from 20 to 300 K, under the excitation of 266 nm laser with 2 mJ pulse energy. With rising temperature, the Ce1 emission is slightly decreased, while the Ce2 emission is slightly increased. These results show the emissions of Ce1 and Ce2 is not only dependent on the concentration ratio but also influenced by the possible energy transfer processes, including Ce1 to Ce2, intrinsic STHs to Ce2 and the phonon-assisted transfer processes. The spectral thermal broadening and the spectral overlap become evident at high temperature, leading to the enhancement of energy transfer. When the excitation power lowers, the ratio of Ce1 and Ce2 emission increases, and is close to the Xe lamp ultraviolet (UV) excitation, suggesting that the energy transfer from Ce1 center to Ce2 center may be also dependent on the excitation power.     

Three-level operation of a diode-bar-pumped Yb:S-FAP laser

We present an all solid-state Yb:S-FAP laser system running on the three-level laser transition at 985 nm. The pump source was a high fill-factor laser diode bar, with the output reformatted using a two-mirror beamshaping system to produce a rectangular pump beam that focused to a square spot. A nearly on-axis multipassing system was used to obtain four pump passes through a 1.6 mm Yb:S-FAP laser crystal. Gain-switched three-level laser output was achieved with an efficiency of 4.3% with respect to incident pump power. Electro-optic Q-switching produced 0.12 mJ pulses for a pump pulse energy of 11 mJ. Intra-cavity second-harmonic generation yielded a maximum pulse energy at 492.5 nm of 12 μJ.     

Specialty Yb fiber amplifier for microchip Nd laser: Towards ∼1-mJ/1-ns output at kHz-range repetition rate

We demonstrate and optimize, for a mJ/ns release at the wavelength 1.064 μm, the operation of a compact laser system designed in the form of a hybrid, active-passive, Q-switched Nd³⁺:YAG/Cr⁴⁺:YAG microchip laser seeding an Yb-doped specialty multi-port fiber amplifier. As the result of the amplifier optimization, ∼1 mJ, ∼1 ns, almost single-mode pulses at a 1-10-kHz repetition rate are achieved, given by a gain factor of ∼19 dB for an 11-μJ input from the microchip laser. Meanwhile, a lower pulse energy, ∼120 μJ, but a much higher gain (∼25 dB) are eligible for the less powerful (0.35 μJ) input pulses.     

Pulsed inductive discharge CO2 laser

A pulsed inductive discharge CO₂ laser with a wavelength of 10.6 μm has been created for the first time. The excitation system of a cylindrical pulsed inductive discharge (pulsed inductively coupled plasma) in the gas mixture of CO₂:N₂:He was developed. The temporal and energy parameters of the laser radiation were investigated. The maximum inductive discharge CO₂ laser radiation energy of 104 mJ was achieved. An average power of 3.2 W was obtained at laser generation energy of 65 mJ and pulse repetition rate of 50 Hz. In the cross-section, the laser radiation had the ring shape with an external diameter of 34 mm and thickness of 4-5 mm. The measured divergence of laser radiation was 12 mrad.     

Laser on porous silicon after oxidation by irradiation and annealing

Stimulated emission has been observed from oxide structure of silicon when optically excited by 514 nm laser. The photoluminescence (PL) pulse has a Lorentzian shape with a full width at half maximum (FWHM) of 0.5-0.6 nm. The twin peaks at 694 nm and 692 nm are dominated by stimulated emission which can be demonstrated by its threshold behavior and transition from sub-threshold to linear evolution in light emission. The gain coefficient from the evolution of the peak-emission intensity as a function of the optically pumped sample length has been measured. The oxide structure was fabricated by laser irradiation and annealing treatment on silicon. A model for explaining the stimulated emission has been proposed in which the trap states of the interface between oxide of silicon and porous nanocrystal play an important role.