Effect of oxygen pressure on structure and properties of Bi1.5Zn1.0Nb1.5O7 pyrochlore thin films prepared by pulsed laser deposition

The Bi₂O₃-ZnO-Nb₂O₅ (BZN) cubic pyrochlore thin films were prepared on Pt/TiO₂/SiO₂/Si(1 0 0) substrates by using pulsed laser deposition process. The oxygen pressure was varied in the range of 5-50 Pa to investigate its effect on the structure and dielectric properties of BZN thin films. It is found that oxygen pressure during deposition plays an important role on structure and other properties of BZN films. The BZN films deposited at temperature of 650 °C and at O₂ pressure of 5 Pa have an amorphous BZN and Nb₂O₅ phases but exhibits a cubic pyrochlore structure with a preferential (2 2 2) orientation when the oxygen pressure increases to 10 Pa. Dielectric constant and loss tangent of the films deposited at 10 Pa are 185 and 0.0008 at 10 kHz, respectively. The dielectric tunability is about 10% at a dc bias field of 0.9 MV/cm.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

Effect of UV lamp irradiation during oxidation of Zr/Pt/Si structure on electrical properties of Pt/ZrO2/Pt/Si structure

Metal-insulator-metal (MIM) capacitors were fabricated using ZrO₂ films and the effects of structural and native defects of the ZrO₂ films on the electrical and dielectric properties were investigated. For preparing ZrO₂ films, Zr films were deposited on Pt/Si substrates by ion beam deposition (IBD) system with/without substrate bias voltages and oxidized at 200 °C for 60 min under 0.1 MPa O₂ atmosphere with/without UV light irradiation (λ = 193 nm, Deep UV lamp). The ZrO₂(∼12 nm) films on Pt(∼100 nm)/Si were characterized by X-ray diffraction pattern (XRD), field emission scanning electron microscopy (FE-SEM) and high-resolution transmission electron microscopy (HRTEM), capacitance-voltage (C-V) and current-voltage (I-V) measurements were carried out on MIM structures. ZrO₂ films, fabricated by oxidizing the Zr film deposited with substrate bias voltage under UV light irradiation, show the highest capacitance (784 pF) and the lowest leakage current density. The active oxygen species formed by UV irradiation are considered to play an important role in the reduction of the leakage current density, because they can reduce the density of oxygen vacancies.     

Preparation and magnetoresistance of thin CrO2 films

Highly textured chromium dioxide (CrO₂) films have been deposited on Al₂O₃ single-crystal substrates by atmospheric pressure chemical vapor deposition method (CVD). X-ray diffraction patterns show that the CrO₂ films are (1 0 0)-oriented on Al₂O₃ (0 0 1) substrates, and are (1 0 1)-oriented on Al₂O₃ (0 1 2) substrates. Scanning electron microscopy images indicate that the (1 0 0)-oriented CrO₂ films grown on Al₂O₃ (0 0 1) substrates have smoother surface and better qualities than that grown on Al₂O₃ (0 1 2) substrate. At room temperature, the magnetoresistance of the (1 0 0)- and (1 0 1)-oriented CrO₂ films are nearly same, and both show a linear dependence on applied magnetic field. While at 80 K, the (1 0 1)-oriented CrO₂ films show a much larger magnetoresistance compared with the (1 0 0)-oriented CrO₂ films. The reasons are briefly discussed.     

Pulsed-laser deposition of smooth thin films of Er, Pr and Nd doped glasses

Thin films of complex oxides have been obtained by pulsed-laser deposition (PLD) from glass targets belonging to the system Li₂O-Al₂O₃-P₂O₅-(RE)₂O₃, with RE = Nd, Pr, Er. The films were deposited on quartz, silicon and ITO/glass substrates using a F₂ laser (λ = 157 nm, ι ≈ 20 ns) for ablation in vacuum. The structural, morphological and optical properties of the oxide films were investigated through IR and UV-VIS spectroscopy, Atomic Force Microscopy (AFM), Scanning Electron Microscopy, Energy Dispersive X-ray Spectroscopy (SEM-EDX) and Spectroscopic Ellipsometry. The laser wavelength was found to be the key parameter to obtain thin films with very smooth surface. In this way new possibilities are opened to grow multilayer structures for photonic applications.     

Dielectric properties of continuous composition spreaded MgO-Ta2O5 thin films

The dielectric properties of MgO-Ta₂O₅ continuous composition spread (CCS) thin films were investigated. The MgO-Ta₂O₅ CCS thin films were deposited on Pt/Ti/SiO₂/Si substrates by off-Axis RF magnetron sputtering system, and then the films were annealed at 350 °C with rapid thermal annealing system in vacuum. The dielectric constant and loss of MgO-Ta₂O₅ CCS thin films were plotted via 1500 micron-step measuring. The specific point of Ta₂O₅-MgO CCS thin film (post annealed at 350 °C) showing superior dielectric properties of high dielectric constant (k ∼ 28) and low dielectric loss (tan δ < 0⋅004) at 1 MHz were found in the area of 3-5 mm apart from Ta₂O₅ side on the substrate. The cation's composition of thin film was Mg:Ta = 0.4:2 at%.     

Microstructure and dielectric properties of (Ba0.6Sr0.4)TiO3 thin films grown on super smooth glazed-Al2O3 ceramics substrate

Modified substrates with nanometer scale smooth surface were obtained via coating a layer of CaO-Al₂O₃-SiO₂ (CaAlSi) high temperature glaze with proper additives on the rough-95% Al₂O₃ ceramics substrates. (Ba_0.6Sr_0.4)TiO₃ (BST) thin films were deposited on modified Al₂O₃ substrates by radio-frequency magnetron sputtering. The microstructure, dielectric, and insulating properties of BST thin films grown on glazed-Al₂O₃ substrates were investigated by X-ray diffraction (XRD), atomic force microscope (AFM), and dielectric properties measurement. These results showed that microstructure and dielectric properties of BST thin films grown on glazed-Al₂O₃ substrates were almost consistent with that of BST thin films grown on LaAlO₃ (1 0 0) single-crystal substrates. Thus, the expensive single-crystal substrates may be substituted by extremely cheap glazed-Al₂O₃ substrates.     

Reduced dielectric loss and leakage current in CaCu3Ti4O12/SiO2/CaCu3Ti4O12 multilayered films

The CaCu₃Ti₄O₁₂/SiO₂/CaCu₃Ti₄O₁₂ (CCTO/SiO₂/CCTO) multilayered films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition method. It has been demonstrated that the dielectric loss and the leakage current density were significantly reduced with the increase of the SiO₂ layer thickness, accompanied with a decrease of the dielectric constant. The CCTO film with a 20 nm SiO₂ layer showed a dielectric loss of 0.065 at 100 kHz and the leakage current density of 6×10⁻⁷ A/cm² at 100 kV/cm, which were much lower than those of the single layer CCTO films. The improvement of the electric properties is ascribed to two reasons: one is the improved crystallinity; the other is the reduced free carriers in the multilayered films.     

Surface morphology of DyxOy films grown on Si

The crystalline structure and surface morphology of Dy_xO_y dielectric films grown on Si substrates were studied by grazing incidence diffraction and absorption with use of synchrotron radiation and by atomic force microscopy. The crystalline structure and the roughness of Dy_xO_y films were found to be strongly dependent on the deposition rate. The dielectric-silicon interface depends on the type of gas used in the annealing process. Moreover, results from the near edge X-ray absorption studies, have revealed that none of the examined films has a stoichiometry close to the Dy₂O₃. The level of stoichiometry is determined by the technological conditions. Nevertheless, MOS structures with Dy_xO_y films (EOT ∼ 23 Å) have shown a rather good Dy_xO_y-Si interface properties, which can be further improve by thermal annealing, and introducing of several additives, therefore Dy_xO_y films can be considered as suitable candidates for gate dielectric in MOS devices.     

Investigation of interface roughness cross-correlation properties of optical thin films from total scattering losses

The interface roughness and interface roughness cross-correlation properties affect the scattering losses of high-quality optical thin films. In this paper, the theoretical models of light scattering induced by surface and interface roughness of optical thin films are concisely presented. Furthermore, influence of interface roughness cross-correlation properties to light scattering is analyzed by total scattering losses. Moreover, single-layer TiO₂ thin film thickness, substrate roughness of K9 glass and ion beam assisted deposition (IBAD) technique effect on interface roughness cross-correlation properties are studied by experiments, respectively. A 17-layer dielectric quarter-wave high reflection multilayer is analyzed by total scattering losses. The results show that the interface roughness cross-correlation properties depend on TiO₂ thin film thickness, substrate roughness and deposition technique. The interface roughness cross-correlation properties decrease with the increase of film thickness or the decrease of substrates roughness. Furthermore, ion beam assisted deposition technique can increase the interface roughness cross-correlation properties of optical thin films. The measured total scattering losses of 17-layer dielectric quarter-wave high reflection multilayer deposited with IBAD indicate that completely correlated interface model can be observed, when substrate roughness is about 2.84 nm.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Dependence of excess bismuth content in precursor sols on ferroelectric and dielectric properties of Bi3.25La0.75Ti3O12 thin films fabricated by chemical solution deposition

Bi_3.25La_0.75Ti₃O₁₂ (BLT) thin films were fabricated on Pt/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD), and the dependence of ferroelectric and dielectric properties of the as-deposited BLT thin films on excess Bi content in precursor sols was studied. It is found that the prepared BLT thin film shows the best polarization-electric field, capacitance-voltage and dielectric constant (?_r)-frequency characteristics, when the value of excess Bi content in precursor sols is 10%. In detail, its remnant polarization (2P_r) value is 40 μC/cm², the capacitance tunability is 21% measured at room temperature under conditions of an applied voltage of 8 V and measurement frequency of 10 kHz, and the ?_r is 696 at 100 kHz frequency.     

Growth and characterization of Y2O3 thin films

Y₂O₃ thin films were grown on silicon (1 0 0) substrates by pulsed-laser deposition at different substrate temperatures and O₂ pressures. The structure and composition of films are studied by using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Y₂O₃ thin films deposited in vacuum strongly oriented their [1 1 1] axis of the cubic structure and the film quality depended on the substrate temperature. The magnitude of O₂ pressure obviously influences the film structure and quality. Due to the silicon diffusion and interface reaction during the deposition, yttrium silicate and SiO₂ were formed. The strong relationship between composition and growth condition was discussed.     

Influence of MgO and ZrO2 buffer layers on dielectric properties of Ba(Zr0.20Ti0.80)O3 thin films prepared by sol-gel processing

Ba(Zr_0.20Ti_0.80)O₃ (BZT) thin films are deposited on Pt(1 1 1)/Ti/SiO₂/Si, MgO and ZrO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel process. The BZT thin films directly grown on Pt(1 1 1)/Ti/SiO₂/Si substrates exhibit highly (1 1 1) preferred orientation, while the films deposited on Pt(1 1 1)/Ti/SiO₂/Si substrates with MgO and ZrO₂ buffer layers show highly (1 1 0) preferred orientation. At 100 kHz, dielectric constants are 417, 311 and 321 for the BZT thin films grown on Pt(1 1 1)/Ti/SiO₂/Si, MgO and ZrO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si substrates, respectively. The difference in dielectric properties of three BZT films can be attributed to the series capacitance effect, interface conditions and their orientations.     

Influence of substrate temperature in BiFeO3-CoFe2O4 nanocomposites deposited on SrTiO3 (0 0 1)

BiFeO₃-CoFe₂O₄ epitaxial nanocomposites have been deposited on SrTiO₃ (0 0 1) substrates by pulsed laser deposition. We present here a study of the influence of the deposition temperature (T_S), in the 550-800 °C range, on the film composition, morphology and microstructure. Electron-probe microanalysis shows strong reduction of the Bi content in the films when increasing T_S. Films prepared at T_S=750 °C and above are virtually Bi-free. X-ray diffraction (XRD) data show that, due to the volatility of Bi, there is a progressive reduction in the amount of BiFeO₃. The deposition temperature and the concomitant presence of Fe_xO_y spurious phases in the nanocomposites grown at high temperature promote radical changes in film morphology and magnetization. It thus follows that a temperature range suitable for controlled modification of nanocomposites morphology would be extremely narrow.     

Persistent luminescence dosimetric properties of UV-irradiated SrAl2O4:Eu, Dy phosphor

Current radiation dosimetry methods involve the release of trapped charge carriers in the form of electrons-holes pairs generated by irradiation exposure of the dosimetric materials. Thermal and optical stimulations of the irradiated material freed the trapped charges that eventually recombine with interband centers producing the emission of light. The integrated intensity of the emitted light is proportional to the radiation dose exposure. In this work, we present an UV radiation dosimetry technique based on the characteristic persistence luminescence (PLUM) 4f⁶5d¹→4f⁷ electronic transition of Eu²⁺ ions in SrAl₂O₄:Eu²⁺, Dy³⁺. The dose assessment is carried out by measuring the PLUM signal integrated during a certain time. The PLUM performance of SrAl₂O₄:Eu²⁺, Dy³⁺ phosphor exhibited a linear behavior for the first 50 s of UV irradiation. For higher UV time exposure the behavior is sublinear with no apparent saturation during a 10 min period. The PLUM dosimetry response was performed at 400 nm that corresponds to the main band component of the PLUM excitation spectrum in the 250-500 nm range. The main advantage of a dosimeter device based on the PLUM of SrAl₂O₄:Eu²⁺, Dy³⁺ is that neither thermal nor optical stimulation is required, avoiding the need of cumbersome electronic photo/thermal stimulation equipment. Due to the highly efficient 250-500 nm PLUM response of SrAl₂O₄:Eu²⁺, Dy³⁺, it could have potential application as UV radiation dosimeter in the UV range of grate human health concerns caused by UV solar radiation.     

Role of crystal orientation on the magnetic properties of CoFe2O4 thin films grown on Si (1 0 0) and Al2O3 (0 0 0 1) substrates using pulsed laser deposition

We report the influence of crystal orientation on the magnetic properties of CoFe₂O₄ (CFO) thin films grown on single crystal Si (1 0 0) and c-cut sapphire (Al₂O₃) (0 0 0 1) substrates using pulsed laser deposition technique. The thickness was varied from 200 to 50 nm for CFO films grown on Si substrates, while it was fixed at 200 nm for CFO films grown on Al₂O₃ substrates. We observed that the 200 and 100 nm thick CFO-Si films grew in both (1 1 1) and (3 1 1) directions and displayed out-of-plane anisotropy, whereas the 50 nm thick CFO-Si film showed only an (1 1 1) orientation and an in-plane anisotropy. The 200 nm thick CFO film grown on an Al₂O₃ substrate was also found to show a complete (1 1 1) orientation and a strong in-plane anisotropy. These observations pointed to a definite relation between the crystalline orientation and the observed magnetic anisotropy in the CFO thin films.     

Effect of deposition temperature on orientation and electrical properties of (K0.5Na0.5)NbO3 thin films by pulsed laser deposition

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) thin films have been prepared on Pt/TiO₂/SiO₂/Si substrates by pulsed laser deposition process. The structures, crystal orientations and electrical properties of thin films have been investigated as a function of deposition temperature from 680 °C to 760 °C. It is found that the deposition temperature plays an important role in the structures, crystal orientations and electrical properties of thin films. The crystallization of thin films improves with increasing deposition temperature. The thin film deposited at 760 °C exhibits strong (0 0 1) preferential orientation, large dielectric constant of 930 and the remnant polarization of 8.54 μC/cm².     

PLD of Fe3O4 thin films: Influence of background gas on surface morphology and magnetic properties

Ablation of Fe₃O₄ targets has been performed using a pulsed UV laser (KrF, λ = 248 nm, 30 ns pulse duration) onto Si(100) substrates, in reactive atmospheres of O₂ and/or Ar, with different oxygen partial pressures. The as-deposited films were characterised by atomic force microscopy (AFM), X-ray diffraction (XRD), conversion electron Mössbauer spectroscopy (CEMS) and extraction magnetometry, in order to optimise the deposition conditions in the low temperature range. The results show that a background mixture of oxygen and argon improves the Fe:O ratio in the films as long as the oxygen partial pressure is maintained in the 10⁻² Pa range. Thin films of almost stoichiometric single phase polycrystalline magnetite, Fe_2.99O₄, have been obtained at 483 K and working pressure of 7.8 × 10⁻² Pa, with a high-field magnetization of ∼490 emu/cm³ and Verwey transition temperature of 112 K, close to the values reported in the literature for bulk magnetite.     

Nanolayered multilayer coatings of CrN/CrAlN prepared by reactive DC magnetron sputtering

Single-phase CrN and CrAlN coatings were deposited on silicon and mild steel substrates using a reactive DC magnetron sputtering system. The structural characterization of the coatings was done using X-ray diffraction (XRD). The XRD data showed that both the CrN and CrAlN coatings exhibited B1 NaCl structure with a prominent reflection along (2 0 0) plane. The bonding structure of the coatings was characterized by X-ray photoelectron spectroscopy and the surface morphology of the coatings was studied using atomic force microscopy. Subsequently, nanolayered CrN/CrAlN multilayer coatings with a total thickness of approximately 1 μm were deposited on silicon substrates at different modulation wavelengths (Λ). The XRD data showed that all the multilayer coatings were textured along {2 0 0}. The CrN/CrAlN multilayer coatings exhibited a maximum nanoindentation hardness of 3125 kg/mm² at a modulation wavelength of 72 Å, whereas single layer CrN and CrAlN deposited under similar conditions exhibited hardness values of 2375 and 2800 kg/mm², respectively. Structural changes as a result of heating of the multilayer coatings in air (400-800 °C) were characterized using XRD and micro-Raman spectroscopy. The XRD data showed that the multilayer coatings were stable up to a temperature of 650 °C and peaks pertaining to Cr₂O₃ started appearing at 700 °C. These results were confirmed by micro-Raman spectroscopy. Nanoindentation measurements performed on the heat-treated coatings revealed that the multilayer coatings retained hardness as high as 2250 kg/mm² after annealing up to a temperature of 600 °C.