Magnetic,structural and electrical properties of ordered and disordered Co50Fe50 films

Co₅₀Fe₅₀ films with thickness varying from 100 to 500 Å were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 °C for 5 h in a vacuum of 5×10⁻⁶ mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co₅₀Fe₅₀ is increased, the saturation magnetization (M_s) and coercivity (H_c) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 °C.     

Thermal equation-of-state of osmium: a synchrotron X-ray diffraction study

The pressure-volume-temperature behavior of osmium was studied at pressures and temperatures up to 15 GPa and 1273 K. In situ measurements were conducted using energy-dispersive synchrotron X-ray diffraction in a T-cup 6-8 high pressure apparatus. A fit of room-temperature data by the third-order Birch-Murnaghan equation-of-state yielded isothermal bulk modulus K₀=435(19) GPa and its pressure derivative K′₀=3.5(0.8) GPa. High-temperature data were analyzed using Birch-Murnaghan equation of state and thermal pressure approach. The temperature derivative of bulk modulus was found to be −0.061(9) GPa K⁻¹. Significant anisotropy of osmium compressibility was observed.     

High pressure X-ray diffraction study of ReS2

The high-pressure behavior of rhenium disulfide (ReS₂) has been investigated to 51.0 GPa by in situ synchrotron X-ray diffraction in a diamond anvil cell at room temperature. The results demonstrate that the ReS₂ triclinic phase is stable up to 11.3 GPa, at which pressure the ReS₂ transforms to a new high-pressure phase, which is tentatively identified with a hexagonal lattice in space group P6?m2. The high-pressure phase is stable up to the highest pressure in this study (51.0 GPa) and not quenchable upon decompression to ambient pressure. The compressibility of the triclinic phase exhibits anisotropy, meaning that it is more compressive along interlayer directions than intralayer directions, which demonstrates the properties of the weak interlayer van der Waals interactions and the strong intralayer covalent bonds. The largest change in the unit cell angles with increasing pressures is the increase of β, which indicates a rotation of the sulfur atoms around the rhenium atoms during the compression. Fitting the experimental data of the triclinic phase to the third-order Birch-Murnaghan EOS yields a bulk modulus of K_OT=23±4 GPa with its pressure derivative K_OT′= 29±8, and the second-order yields K_OT=49±3 GPa.     

High pressure X-ray diffraction study on icosahedral boron arsenide (B12As2)

The high pressure properties of icosahedral boron arsenide (B₁₂As₂) were studied by in situ X-ray diffraction measurements at pressures up to 25.5 GPa at room temperature. B₁₂As₂ retains its rhombohedral structure; no phase transition was observed in the pressure range. The bulk modulus was determined to be 216 GPa with the pressure derivative 2.2. Anisotropy was observed in the compressibility of B₁₂As₂—c-axis was 16.2% more compressible than a-axis. The boron icosahedron plays a dominant role in the compressibility of boron-rich compounds.     

A high-pressure Raman and X-ray diffraction study of the perovskite SrCeO3

A high-pressure structural study of SrCeO₃ has been performed at room temperature by Raman spectroscopy and X-ray diffraction up to 32 and 45 GPa, respectively. A first-order reversible phase transition is observed at about 12 GPa in both techniques. A second weak structural change, taking place between 18 and 25 GPa, can be suspected from Raman data. The increase in the number of Raman bands and diffraction lines is an indication that the symmetry is lowered and the compound does not evolve towards the ideal cubic perovskite structure. A Rietveld analysis of X-ray data was performed for the low-pressure phase and the atomic positions and the cell lattice parameters variations are reported in this paper. The volume compressibility derived from Raman modes (5.6×10⁻¹² Pa⁻¹), involving mainly bond-stretching for each type of polyhedron, is found to be close to the one obtained from volume cell variations measured by X-ray diffraction (7.9×10⁻¹² Pa⁻¹).     

In situ observations of temperature- and pressure-induced phase transitions in TiH2: Angle-dispersive and synchrotron energy-dispersive X-ray diffraction studies

We investigated the behavior of the structure of titanium hydride (TiH₂), an important compound in hydrogen storage research, at elevated temperatures (0-120 °C) and high pressures (1 bar-34 GPa). Temperature-induced changes of TiH₂ as indicated in the alteration of the ambient X-ray demonstrated a cubic to tetragonal phase transition occurring at about 17 °C. The main focus of this study was to identify any pressure-induced structural transformations, including possible phase transitions, in TiH₂. Synchrotron X-ray diffraction studies were carried out in situ (diamond anvil cell) in a compression sequence up to 34 GPa and in subsequent decompression to ambient pressure. The pressure evolution of the diffraction patterns revealed a cubic (Fm-3m) to tetragonal (I4/mmm) phase transition at 2.2 GPa. The high-pressure phase persisted up to 34 GPa. After decompression to ambient conditions the observed phase transition was completely reversible. A Birch-Murnaghan fit of the unit cell volume as a function of pressure yielded a zero-pressure bulk modulus K₀=146(14) GPa, and its pressure derivative K′₀=6(1) for the high-pressure tetragonal phase of TiH₂.     

Crystal structure and compressibility of a high-pressure Ti-rich oxide, (Ti0.50Zr0.26Mg0.14Cr0.10)O1.81, isomorphous with cubic zirconia

A Ti-rich oxide, (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)_∑=1.0O_1.81, was synthesized at 8.8 GPa and 1600 °C using a multi-anvil apparatus. Its crystal structure at ambient conditions and compressibility up to 10.58 GPa were determined with single-crystal X-ray diffraction. This high-pressure phase is isomorphous with cubic zirconia (fluorite-type) with space group Fm3¯m and unit-cell parameters a=4.8830(5) Å and V=116.43(4) Å³. Like stabilized cubic zirconia, the structure of (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)O_1.81 is also relaxed, with all O atoms displaced from the (, , ) position along 〈1 0 0〉 by 0.319 Å and all cations from the (0, 0, 0) position along 〈1 1 1〉 by 0.203 Å. No phase transformation was detected within the experimental pressure range. Fitting the high-pressure data (V vs. P) to a third-order Birch-Murnaghan EOS yields K₀=164(4) GPa, K′=4.3(7), and V₀=116.38(3) Å³. The bulk modulus of (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)O_1.81 is significantly lower than that (202 GPa) determined experimentally for cubic TiO₂ or that (~210 GPa) estimated for cubic ZrO₂. This study demonstrates that cubic TiO₂ may also be obtained by introducing various dopants, similar to the way cubic zirconia is stabilized below 2370 °C. Furthermore, (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)O_1.81 has the greatest ratio of Ti⁴⁺ content vs. vacant O²⁻ sites of all doped cubic zirconia samples reported thus far, making it a more promising candidate for the development of electrolytes in solid oxide fuel cells.     

Optical properties of methane to 288 GPa at 300 K

Optical properties of solid methane (CH₄) were studied at high pressure and room temperature using a diamond anvil cell. Reflectivity and transmission measurements were used to measure the refractive index to 288 GPa. Fabry-Perot interferometery was used to measure the sample thickness to 172 GPa. This data was fitted to the derived expression of thickness vs. pressure that was then used to calculate the thickness to 288 GPa. This in turn was combined with optical absorption experiments to obtain the absorption coefficient and hence the extinction coefficient k^*. From combined reflection and absorption experiments the refractive index n=n_s+ik^* was obtained. The index of refraction and the ratio of molar refraction to molar volume showed a large increase between 208 and 288 GPa. This behavior indicated that a phase transformation of insulator-semiconductor might have occurred in solid CH₄ by 288 GPa.     

Compression behavior of nanocrystalline anatase TiO2

We present a synchrotron X-ray diffraction study of pressure-induced changes in nanocrystalline anatase (with a crystallite size of 30-40 nm) to 35 GPa. The nanoanatase was observed to a pressure above 20 GPa. Direct transformation to the baddeleyite-TiO₂ polymorph was seen at 18 GPa. A fit of the pressure versus volume data to a Birch-Murnaghan equation yielded the following parameters: zero-pressure volume, V₀=136.15 Å³, bulk modulus, K_T=243(3) GPa, and the pressure derivative of bulk modulus, K′=4 (fixed). The bulk modulus value obtained for the nanocrystalline anatase is about 35% larger than that of the macrocrystalline counterpart.     

High-pressure phase transition of carbon disulfide

The high-pressure phase transition of CS₂ was studied by combing ab initio molecular dynamics with total energy calculations. At 300 K the pieces of polymer structure were found to appear at 10 GPa in the molecular dynamics run, and further the CS₄ tetrahedral structure to appear at about 20 GPa. The phase transition was then studied in the structure of Cmca, α-quartz and β-quartz by using the first-principle total energy calculation method. A phase transition from Cmca to β-quartz was found at 10.6 GPa. The calculated lattice constants of β-quartz at atmospheric pressure are a=5.44 and c/a=1.138 with B₀=95 GPa. The calculation has also indicated that CS₂ decomposes at 20 GPa and below 1000 K.     

High-pressure powder diffraction study of TaO2F

TaO₂F, with a ReO₃-type structure, has been studied at up to 12.8 GPa using monochromatic synchrotron powder diffraction and diamond anvil cells. Two-phase transitions at ∼0.7 and 4 GPa were observed on compression. Below ∼0.7 GPa the cubic material was found to have a bulk modulus (K₀) of 36(3) GPa (K_p fixed at 4.0), similar to that reported for NbO₂F but much smaller than that of ReO₃. Immediately above 0.7 GPa on compression, the diffraction data were not fully consistent with a VF₃-type structure as previously proposed for NbO₂F. On decompression, the data between 8 and 4 GPa could be satisfactorily attributed to a single R-3c phase with a VF₃-type structure and an average bulk modulus of 60(2) GPa.     

High pressure behaviour of KHSO4 studied by electrical impedance spectroscopy

Measurements of the electrical conductivity were performed in KHSO₄ at pressures between 0.5 and 2.5 GPa and in the temperature range 120-350 °C by the use of the impedance spectroscopy. The temperatures of the α-β phase transition (T_Tr) and of the melting (T_m), determined from the Arrhenius plots ln(σT) vs. 1/T, increase with pressure up to 1.5 GPa having dT/dP∼+45 K/GPa. Above the pressure 1.5 GPa, the pressure dependencies of T_Tr and T_m are negative dT/dP∼−45 K/GPa. At pressures above 0.5 GPa, the reversible decomposition of KHSO₄ into K₃H(SO₄)₂+H₂SO₄ (and probably into K₅H₃(SO₄)₄+H₂SO₄) affects the electrical conductivity of KHSO₄, with the typical values of the protonic electrical conductivity, c. 10⁻¹ S/cm at 2.5 GPa.     

Structural property of CsCl-type sodium chloride under pressure

The structure and equation of state of CsCl-type sodium chloride have been determined using high-pressure powder X-ray diffraction from 32 to 134 GPa. The CsCl-type phase remains stable over this entire pressure range. Pressure-volume data can be fitted with a Vinet equation of state with K_30 GPa=135.1 GPa, K′_30 GPa=3.9, and V_30 GPa=27.70 Å³. The nearest-neighbour distance between sodium and chlorine atoms decreased as pressure increased. Significant discrepancies of nearest-neighbour distance between previous theoretical predictions and this study were observed at pressures higher than 70 GPa.     

Spin gap of a pressure-induced superconductor Sr2Ca12Cu24O41 at an optimum pressure of 3.8 GPa

Nuclear magnetic resonance (NMR) on ⁶³Cu nuclei was performed in a pressure-induced superconductor Sr₂Ca₁₂Cu₂₄O₄₁ at an optimum pressure of 3.8 GPa. A pressure of 3.8 GPa was achieved by improving a piston-cylinder-type pressure cell and developing a NMR probe with a steady-load control system. We found that the spin gap still exists even at the optimum pressure. The spin gap was almost the same at pressures below 3.5 GPa on the pressure-temperature phase diagram, whereas it decreased rather drastically above 3.5 GPa.     

Pressure-induced transition in a heavy fermion YbPd2Si2

We report the results of a room-temperature investigation of the thermoelectric and the dilatometric properties of a heavy fermion system YbPd₂Si₂ (itterbium-palladium-silicon, 1-2-2) at high pressure P up to 22 GPa; YbPd₂Si₂ is a less-studied representative of the RM₂X₂ family (R=Ce, Yb, U; M=transition metal; X=Si, Ge) with the tetragonal ThCr₂Si₂-type structure of the I4/mmm space group. Around P∼6±0.5 GPa, a phase transition in Yb-Pd-Si was registered by the drastic changes in the pressure dependencies of the electrical resistance R, the thermopower (Seebeck effect) S, a temperature difference along a sample ΔT, and a sample's thickness Δx (related to compressibility). Both a nature of the found phase transition and a presumable P-T phase diagram of YbPd₂Si₂ are discussed.     

Phase transition of Ta2NiO6 with the trirutile-type structure under high pressure and high temperature

High-pressure phase transition of Ta₂NiO₆ with the trirutile-type structure was investigated from the viewpoint of crystal chemistry. A new quenchable high-pressure phase was found in the pressure range higher than 7 GPa and 900°C. The high-pressure phase has an orthorhombic cell (a=4.797(1) Å, b=5.153(2) Å and c=14.85(1) Å and space group; Abm2), and it is more dense by 9.6% than the trirutile-structured phase. Infrared spectra of the trirutile-type phase and the high-pressure phase show that Ni²⁺ ions in the high-pressure phase are still in octahedral sites. The crystal structure of the high-pressure phase is considered as a cation-ordering trifluorite-type structure, which can be stabilized by a crystal field effect of Ni²⁺ ions.     

The bulk modulus of SmFeAs(O0.93F0.07)

The crystal structure of SmFeAs(O_0.93F_0.07) has been investigated under high pressure (up to ∼9 GPa) by means of synchrotron powder diffraction analysis followed by Rietveld refinement. The bulk modulus was calculated (K₀ = 103 GPa) using a 3rd order Birch–Murnaghan equation of state and resulted in quite good agreement with theoretical calculations reported for LaFeAsO. The linear compressibilities β_a and β_c are 2.11(4) and 4.56(7) × 10⁻³ GPa⁻¹, respectively.     

In situ X-ray observation of phase transformation in Fe2O3 at high pressures and high temperatures

A laser-heated sample in a diamond anvil cell and synchrotron X-ray radiation was used to carry out structural characterization of the phase transformation of Fe₂O₃ at high pressures (30-96 GPa) and high temperature. The Rh₂O₃(II) (or orthorhombic perovskite) structure transforms to a new phase, which exhibits X-ray diffraction data that are indicative of a CaIrO₃-type structure. The CaIrO₃-type structure exhibited an orthorhombic symmetry (space group: Cmcm) that was stable at temperatures of 1200-2800 K and pressure of 96 GPa (the highest pressure used). Unambiguous assignment of such a structure requires experimental evidence for the presence of two Fe species. Based on the equation of state of gold, the phase boundary of the CaIrO₃-type phase transformation was P (GPa)=59+0.0022×(T−1200) (K).     

Structure and high pressure behaviour of organic crystals based on aromatically substituted 1,3,4-oxadiazoles

The crystalline structure of a new compound containing the 1,3,4-oxadiazole moiety, 4-(5-methyl-1,3,4-oxadiazole-2yl-)-N,N′-dimethyl-phenylamine (MODPA) was determined. It shows a monoclinic structure with space group P2₁/c and lattice parameters: a=1.02997(6), b=0.64840(4), c=1.58117(10) nm and β=99.4820(10)°. To study the intermolecular interactions in oxadiazole containing organic crystals, X-ray studies on MODPA and 2,5-diphenyl-1,3,4-oxadiazole (DPO) were performed up to 5 GPa at room temperature. The Murnaghan equation of state is used to describe the compression behaviour of both substances. From these results, the bulk modulus and its pressure derivative were determined. The values obtained are: K₀=6.3 GPa and K′₀=6.8 for MODPA and K₀=7.3 GPa and K′₀=6.7 for DPO. Additionally, measurements under increasing temperature at ambient pressure were carried out to evaluate the thermal expansion coefficient: α=1.8×10⁻⁴ K⁻¹ for MODPA and α=1.9×10⁻⁴ K⁻¹ for DPO.     

Electric field gradient at Ru nuclei in the series of intermetallic compounds Ce1−xLaxRu2 synthesized at high pressure

Parameters of the electric quadrupole interaction for the first excited state (E=89.7 keV) of ⁹⁹Ru nuclei for a number of the cubic Laves phase compounds Ce_1−xLa_xRu₂, synthesized at high pressure, were determined by the perturbed angular γγ-correlation method. Compounds were synthesized at 8 GPa. It was revealed that the decrease of the average valence of a rare earth ion, caused by the substitution of La for Ce, results in the monotonous decrease of the quadrupole frequency ν_Q from 43.3 MHz for CeRu₂ to 33.1 MHz for LaRu₂.