Effect of holmium substitution for the improvement of multiferroic properties of BiFeO3

This paper reports on multiferroic properties of Ho substituted BiFeO₃ (Bi_1−xHo_xFeO₃) ceramics. It is observed that for x=0.15, a prominent ferroelectric loop is seen at 300 K even if the system remains in rhombohedral (R3c) phase without appearance of any observable impurity phases. A well shaped M-H loop is observed at 10 K for x=0.15. However it showed ferromagnetism, confirming the contribution of Ho³⁺ towards enhancement of ferromagnetic properties of BiFeO₃ at 300 K. Suppression of impurity phases of pure BiFeO₃ bulk ceramic favors the reduction of mobile oxygen vacancies and reduces leakage current, due to which ferroelectric properties of BiFeO₃ is enhanced. We argue that Ho substitution at Bi site is likely to suppress the spiral spin modulation and at the same time increase the canting angle, which favors enhanced multiferroic properties. XRD, SEM, magnetization, polarization and chemical bonding analysis measurements were carried out to explain the multiferroic behavior.     

Effect of Dy substitution on structural,magnetic and optical properties of BiFeO3 ceramics

Bi_1−xDy_xFeO₃ (x=0.0, 0.03, 0.05, 0.07, 0.10 and 0.12) ceramics were synthesized by solid state reaction method. Effects of Dy substitution on structural distortion, magnetic and optical properties of BiFeO₃ were examined by X-ray diffraction, Raman and UV–Visible spectroscopy. The samples were found to crystallize in rhombohedral structure of BiFeO₃ with R3c space group. The reduction in lattice parameters and unit cell volume indicate the distortion in FeO₆ octahedra of the rhombohedral structure without any signature of phase transformation up to x=0.12. The predictable weak ferromagnetic hysteresis loops can be observed in the Dy doped samples with maximum remnant magnetization of 0.2103 emu/g for x=0.12. The weak ferromagnetism is ascribed to the suppressed spiral spin structure and magnetically active characteristic of Dy³⁺ ions together with ferromagnetic coupling between Dy³⁺ and Fe³⁺ ions. With optical band gap in visible region, Dy doped BiFeO₃ ceramics are potential material for optoelectronic device and solar cell applications.     

Post-sintering annealing effect on the diffuse phase transition in (Pb1−xBax)(Yb0.5Ta0.5)O3 ceramics

The effect of post sintering annealing on the dielectric response of (Pb_1−xBa_x)(Yb_0.5Ta_0.5)O₃ ceramics in the diffuse phase transition range (x=0.2) has been investigated. The samples are prepared by conventional solid-state reaction method. The samples are sintered at 1300 °C for 2 h and annealed at different temperatures (800, 900 and 1000 °C) for 8 h and at 800 °C for different time durations (8, 12 and 24 h). A significant change in the dielectric response has been observed in all the samples. The dielectric constant increases remarkably and the dielectric loss tangent decreases. The dielectric peaks of the annealed samples are observed to be more diffused with noticeable frequency dispersion compared to the as sintered sample.     

Enhanced multiferroic properties in La and Ce co-doped BiFeO3 nanoparticles

Room temperature multiferroic properties of BiFeO₃ (BFO), Bi_0.9La_0.1FeO₃ ((La)BFO) and Bi_0.9La_0.075Ce_0.025FeO₃ ((La,Ce)BFO) nanoparticles have been reported in this paper. XRD (X-ray diffraction) analyses of the nanoparticles show a decrease in the lattice constants and cell volume with the substitution of La and Ce. It is evident from the SEM (scanning electron microscope) micrographs that the (La,Ce) co-doped sample possesses dense microstructure made of smaller particles. Raman study accounts for the weakening of the strong hybridization between Bi-O by the substitution of La and Ce ions. This is also accompanied by an increase in the remanent magnetization, dielectric constant, and ferroelectric polarization. BFO nanoparticles show exchange bias effect under an applied magnetic field while the (La)BFO and (La,Ce)BFO samples show no trace of such effect. Ac-conductivity of (La,Ce) co-doped sample is observed to be several orders lesser in magnitude than bulk BFO ceramics. These results are interpreted by means of the subtle change in the structure, suppression of the spin cycloid and reduction of oxygen vacancies in the doped samples.     

High temperature structural studies of SrRhO3

High resolution X-ray powder diffraction studies have shown SrRhO₃ to transform from an orthorhombic Pnma structure at room temperature through an intermediate Imma phase to a tetragonal I4/mcm structure near 800 °C. The orthorhombic Imma phase exists over a very limited temperature range, of less than 20°. The diffraction data suggests the Pnma to Imma transition is continuous and demonstrates that the Imma-I4/mcm transition is first order.     

Phase evolution and microwave dielectric properties of Bi3SbO7 ceramic

The Bi₃SbO₇ ceramic was prepared by the solid state reaction method and its phase evolution at different temperatures was studied. Low temperature phase α-Bi₃SbO₇ was formed at about 890 °C and it started to transform to high temperature phase β-Bi₃SbO₇ at about 960 °C. Microwave dielectric constants of α-Bi₃SbO₇ ceramic and β-Bi₃SbO₇ ceramic were 43.2 and 37.6, Qf value were 2080 and 5080 GHz, respectively. TCF of α-Bi₃SbO₇ ceramic was near zero and TCF of β-Bi₃SbO₇ ceramic was about −120 ppm/°C. The Bi₃SbO₇ ceramic is a promising candidate for low temperature co-fired ceramic (LTCC) technology due to its large dielectric constant, low dielectric loss at microwave region, low sintering temperature and simple composition.     

Effect of Mn-doping on the electrical properties of Cu2GeSe3

In this work we report the temperature dependence of the resistivity ρ of p-Cu₂GeSe₃ and manganese-doped p-Cu₂GeSe₃ at low temperature. It was found that for a intrinsic sample ρ obeys the Shklovskii-Efros-type variable-range hopping resistivity law in the temperature range from 4 to 63 K. This behaviour is governed by generation of a Coulomb gap Δ=78 meV in the density of localized states. We find a low activation term T₀=0.24 K, which is an indication of a large localization length ξ. For Mn-doped sample a metal-insulator transition (MIT) is observed at T=65 K. On the basis of the Mott criterion for metal-insulator transition, the critical carrier density n_c is determined. From the analysis of resistivity data it is concluded that Mn acts as acceptor impurity.     

Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Synthesis, physical and photo electrochemical characterization of La-doped SrSnO3

The transport properties of Sr_0.98La_0.02SnO_3−δ in the system Sr_1−xLa_xSnO_3−δ, after which the pyrochlore La₂Sn₂O₇ appears, were investigated over the temperature range 4.2-300 K. The oxide was found to be n-type semiconductor with concomitant reduction of Sn⁴⁺ into Sn²⁺. The magnetic susceptibility was measured down to 4.2 K and is less than 3×10⁻⁵ emu cgs mol⁻¹ consistent with itinerant electron behavior. The electron is believed to travel in a narrow band of Sn:5s character with an effective mass ∼4 m_o. The highest band gap is 4.32 eV and the optical transition is directly allowed. A further indirect transition occurs at 4.04 eV. The electrical conductivity follows an Arrhenius-type law with a thermal activation of 40 meV and occurs by small polaron hopping between nominal states Sn^4+/2+. The linear increase of thermo-power with temperature yields an electron mobility μ_300 K (2×10⁻⁴ cm² V⁻¹ s⁻¹) thermally activated. The insulating-metal transition seems to be of Anderson type resulting from random positions of lanthanum sites and oxygen vacancies. At low temperatures, the conduction mechanism changes to a variable range hopping with a linear plot Ln ρ⁻¹ vs. T⁻⁴. The photo electrochemical (PEC) measurements confirm the n-type conductivity and give an onset potential of −0.46 V_SCE in KOH (1 M). The Mott-Schottky plot C⁻²-V shows a linear behavior from which the flat band potential V_fb=+0.01 V_SCE at pH 7 and the doping density N_D=1.04×10²¹ cm⁻³ were determined.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Improvement in electrical and magnetic properties of mixed Mg-Al-Mn ferrite system synthesized by citrate precursor technique

In the present work, mixed magnesium-manganese ferrites of composition Mg_0.9Mn_0.1Al_0.3Co_zFe_1.7−zO₄ where z=0.3, 0.5 and 0.7 have been synthesized by the citrate precursor technique. X-ray diffraction patterns of the samples confirmed the formation of single-phase spinel structure. The ferrites have been investigated for their electric and magnetic properties such as dc resistivity, Curie temperature, saturation magnetization, initial permeability and relative loss factor (RLF). Fairly constant value of initial permeability over a wide frequency range (0.1-20 MHz) and low values of the relative loss factor of the order of 10⁻⁴-10⁻⁵, in the frequency range 0.1-30 MHz, are the cardinal achievements of the present investigation. In addition to this, initial permeability was found to increase with an increase in temperature while RLF was observed to be low at these temperatures. The dc resistivity and Curie temperature were found to increase with an increase in cobalt content. The mechanisms contributing to these results are discussed in detail in this paper.     

Multiferroic studies on (BiFeO3)m(BaTiO3)n superlattice structures

BiFeO₃ has been studied extensively due to its room temperature multiferroic features and has been proven as a promising candidate for device applications. But BiFeO₃ possesses some drawbacks like high leakage current and complicated magnetic ordering, giving rise to a canted antiferromagnetic behavior. Hence, a superlattice approach of BiFeO₃ and BaTiO₃ with a good lattice matching was fabricated and the room temperature ferroelectric and ferromagnetic properties were studied. The macroscopic and local probe studies reveal a ferroelectric nature at room temperature, and most importantly a weak ferromagnetic like behavior was observed. The ferromagnetic behavior is expected to arise due to the variation introduced in the spin modulation of single BiFeO₃ layer due to the superstructure formation.     

Synthesis, structural and electrical properties of La and Nb modified Bi4Ti3O12 ferroelectric ceramics

Polycrystalline ceramic samples of Bi_4−xLa_xTi₃O₁₂ (x=0.0, 0.5 and 1) and Bi_3.5La_0.5Ti_3−yNb_yO₁₂ (y=0.02 and 0.04) have been synthesized by standard high temperature solid state reaction method using high purity oxides and carbonates. The effect of lanthanum doping on Bi-site and Nb doping on Ti-site on the structural and electrical properties of Bi₄Ti₃O₁₂ powders was investigated by X-ray diffraction, scanning electron microscopy, dc conductivity and dielectric studies. A better agreement between the observed and calculated X-ray diffraction pattern was obtained by performing the Rietveld refinement with a structural model using the non-centrosymmetric space group Fmmm in all the cases. A better agreement between observed and calculated d-values also shows that the lattice parameters calculated using the Rietveld refinement analysis are better. The increase in lanthanum and niobium contents does not lead to any secondary phases. It is found that La³⁺ doping reduces the material grain size and changes its morphology from the plate-like form to a spherical staking like form. The substitution of Nb for Ti ions affected the degree of disorder and modified the dielectric properties leading to more resistive ceramic compounds. The shape and size of the grains are strongly influenced by the addition of niobium to the system. The activation energies of all the compounds were calculated by measuring their dc electrical conductivities. The frequency and temperature dependent dielectric behavior of all the compounds have also been studied and the results are discussed in detail. The substitution of La and Nb on the Bi and Ti sites decreased the T_c and improved the dielectric and ferroelectric behavior.     

Tuning hydrogen storage properties and reactivity: Investigation of the LiBH4-NaAlH4 system

Tuning the hydrogen storage properties of complex metal hydrides is of vast interest. Here, we investigate the hydrogen release and uptake pathways for a reactive hydride composite, LiBH₄−NaAlH₄ utilizing in situ synchrotron radiation powder X-ray diffraction experiments. Sodium alanate transforms to sodium borohydride via a metathesis reaction during ball milling or by heating at T∼95 °C. NaBH₄ decomposes at ∼340 °C in dynamic vacuum, apparently directly to solid amorphous boron and hydrogen and sodium gas and the latter two elements are lost from the sample. Under other conditions, T=400 °C and p(H₂)=∼1 bar, NaBH₄ only partly decomposes to B and NaH. On the other hand, formation of LiAl is facilitated by dynamic vacuum conditions, which gives access to the full hydrogen contents in the LiBH₄−NaAlH₄ system. Formation of AlB₂ is observed (T∼450 °C) and other phases, possibly AlB_x or Al_1−xLi_xB₂, were observed for the more Li-rich samples. This may open new routes to the stabilization of boron in the solid state in the dehydrogenated state, which is a challenging and important issue for hydrogen storage systems based on borohydrides.     

Multicomponent GeSe2-CdI2-TeO2 (Bi2O3) systems: glass formation and properties

The glass-forming regions of the GeSe₂-CdI₂-TeO₂ (I), GeSe₂-CdI₂-Bi₂O₃ (II) and GeSe₂-TeO₂-Bi₂O₃ (III) systems have been determined. The obtained glassy phases have been characterized by their basic physicochemical parameters such as temperatures of glass transition, crystallization, and melting, density and microhardness. The phase T-X diagram of the GeSe₂-CdI₂ system, which is the basic joint line for systems I and II, has been specified. Three non-variant equilibria (two eutectic and one syntectic) have been observed at temperatures 350, 280 and 375 °C for compositions containing 15, 95 and 33.3 mol% GeSe₂, respectively. A new intermediate phase with probable composition of 2CdI₂·GeSe₂ has been formed.     

Local order and structural transitions in the molecule-based layer ferrimagnet (n-C4H9)4N FeFe(C2O4)3

Local structural order and temperature-dependent structural variation have been studied in the molecular-based layer ferrimagnet (n-C₄H₉)₄N Fe^IIFe^III(C₂O₄)₃ by EXAFS and high resolution X-ray powder diffraction. The EXAFS spectra measured at the Fe K-edge are successfully modelled by successive O, C, O and metal shells, showing that even when there is extensive structural disorder due to stacking faults, the local structural order in this class of ferrimagnets is fully retained. In this salt, which shows remarkable negative magnetisation at low temperature (Néel class Q), the EXAFS Debye-Waller factor has a discontinuity at 40 K, corresponding to one found in the magnetisation. At the same temperature there is also a change in the expansion of the lattice as evidenced by the high resolution X-ray powder diffraction.     

Synthesis, structure and magnetic properties in the Nd2O3-Gd2O3 mixed system synthesized at 1200 °C

Phase relation studies in the Gd₂O₃-Nd₂O₃ system have been performed on (Gd_1−xNd_x)₂O₃ samples (0?x?1) with the purpose of performing a systematic study of the composition effects on their structural and magnetic properties. All the samples were synthesized by calcination of the related oxalates at 1200 °C in order to ensure the complete decomposition of the oxalates. Five phase regions, namely an A-type hexagonal, a B-type monoclinic, a C-type cubic solid solution and two biphasic mixtures of the former three phase fields were detected in this system. The magnetic susceptibility measurements showed the presence of antiferromagnetic interactions in all samples. The Curie-Weiss temperature shows a nonlinear dependence on concentration. Deduced effective magnetic moments are close to the free ion values.     

In situ pressure-induced solid-state amorphization in Sm2(MoO4)3, Eu2(MoO4)3 and Gd2(MoO4)3 crystals: chemical decomposition scenario

The effect of pressure on the phase transformations in Sm₂(MoO₄)₃, Gd₂(MoO₄)₃ and Eu₂(MoO₄)₃ crystals has been studied in situ using synchrotron radiation. All three isostructural compounds undergo a structural phase transition at 2.2-2.8 GPa to a new phase, which is interpreted as a possible precursor of amorphization. Amorphization in these crystals occurs irreversibly over a wide pressure range, and its mechanism, interpreted as a chemical decomposition, is found to be weakly affected by the degree of hydrostaticity.     

First-principles study of the structural, electronic, and magnetic properties of InCCo3 and InNCo3

Spin-polarized calculations were performed to investigate the structural, elastic, electronic, and magnetic properties of InCCo₃ and InNCo₃. The deviation of our calculated lattice parameters and equilibrium volume from experimental results is less than 0.8% and 2.5%, respectively. The obtained values of elasticity moduli C_ij, bulk modulus B, and shear modulus G are discussed. From the calculated band structure and the total and partial densities of states, we have concluded that these compounds are electrical conductors; moreover, they are bonded by a mixture of covalent, ionic, and metallic bonds. Our calculations show that InCCo₃ has nonmagnetic properties, while InNCo₃ could have a magnetic behaviour, with an average magnetic moment about 0.54 μ_B/atom, which is mostly derived from d electrons of the cobalt atoms in the energy range from −5 eV up to the Fermi level.     

Resistance anomaly and structural disorder in NiSi2 under high pressure

Results of X-ray diffraction, electrical resistance, thermoelectric power measurements and electronic band structure calculations on NiSi₂ under high pressure are reported. The thermoelectric power (TEP) changes sign near 0.5 GPa (from +30 to −20 μV/K). As the pressure is increased, the value of TEP increases further in magnitude and near 7 GPa it becomes −50 μV/K. The pressure vs. resistance curve measured up to 30 GPa using diamond anvil (DAC)-based technique exhibits a broad hump near 12 GPa and exhibits hysteresis on pressure release. The ADXRD patterns up to 42 GPa show a gradual irreversible loss of long-range order in NiSi₂ with the diffraction lines progressively broadening under pressure. The FWHM of the diffraction lines show a rapid increase in the half-widths close to 0.5 GPa and also near 12 GPa. The computed band structure at a compression (without any disorder) corresponding to 12 GPa, exhibits an electronic topological transition (ETT). The rapid increase in disorder above 12 GPa implies that the ETT may be facilitating the structural disorder. It is suggested that the pressure drives the material through a region of entropic and energetic barriers and induces disorder in the material.