Experimental and Theoretical Study of Enhanced Photocatalytic Activity of Mg‐Doped ZnO NPs and ZnO/rGO Nanocomposites

A systematic experimental and theoretical study of the origin of the enhanced photocatalytic performance of Mg‐doped ZnO nanoparticles (NPs) and Mg‐doped ZnO/reduced graphene oxide (rGO) nanocomposites has been performed. In addition to Mg, Cd was chosen as a doping material for the bandgap engineering of ZnO NPs, and its effects were compared with that of Mg in the photocatalytic performance of ZnO nanostructures. The experimental results revealed that Mg, as a doping material, recognizably ameliorates the photocatalytic performance of ZnO NPs and ZnO/graphene nanocomposites. Transmission electron microscopy (TEM) images showed that the Mg‐doped and Cd‐doped ZnO NPs had the same size. The optical properties of the samples indicated that Cd narrowed the bandgap, whereas Mg widened the bandgap of the ZnO NPs and the oxygen vacancy concentration was similar for both samples. Based on the experimental results, the narrowing of the bandgap, the particle size, and the oxygen vacancy did not enhance the photocatalytic performance. However, Brunauer–Emmett–Teller (BET) and Barret–Joyner–Halenda (BJH) models showed that Mg caused increased textural properties of the samples, whereas rGO played an opposite role. A theoretical study, conducted by using DFT methods, showed that the improvement in the photocatalytic performance of Mg‐doped ZnO NPs was due to a higher electron transfer from the Mg‐doped ZnO NPs to the dye molecules compared with pristine ZnO and Cd‐doped ZnO NPs. Moreover, according to the experimental results, along with Mg, graphene also played an important role in the photocatalytic performance of ZnO.     

Effect of ZnO nanofillers treated with triethoxy caprylylsilane on the isothermal and non-isothermal crystallization of poly(lactic acid)

The crystallization of PLA-silane surface-treated ZnO nanocomposites was investigated by DSC and compared to that of neat PLA. Several modes of crystallization were considered: isothermal and non-isothermal cold crystallization and also isothermal and non-isothermal melt crystallization. The kinetics of cold crystallization were studied using different methods, namely the Avrami and Ozawa-Flynn-Wall models, to calculate activation energies and kinetic constants. In contrast to what is typically observed when the foreign particles are added in a polymer matrix, the silane surface-treated ZnO delayed the crystallization of PLA and made it more difficult to start. The nucleation activity of the ZnO nanoparticles, ?, was calculated and found to be greater than 1 (? = 1.7). This indicated that ZnO played an anti-nucleating role in the crystallization of PLA nanocomposites. This effect has been linked mainly to the interactions between the silane groups onto the surface of nanoparticles and PLA macromolecules. These interactions which reduce the mobility of polymer chains have been evidenced by rheological experiments.     

Adding Value in Production of Multifunctional Polylactide (PLA)–ZnO Nanocomposite Films through Alternative Manufacturing Methods

Due to the added value conferred by zinc oxide (ZnO) nanofiller, e.g., UV protection, antibacterial action, gas-barrier properties, poly(lactic acid) (PLA)–ZnO nanocomposites show increased interest for utilization as films, textile fibers, and injection molding items. The study highlights the beneficial effects of premixing ZnO in PLA under given conditions and its use as masterbatch (MB), a very promising alternative manufacturing technique. This approach allows reducing the residence time at high processing temperature of the thermo-sensitive PLA matrix in contact of ZnO nanoparticles known for their aptitude to promote degradation effects onto the polyester chains. Various PLA–ZnO MBs containing high contents of silane-treated ZnO nanoparticles (up to 40 wt.% nanofiller specifically treated with triethoxycaprylylsilane) were produced by melt-compounding using twin-screw extruders. Subsequently, the selected MBs were melt blended with pristine PLA to produce nanocomposite films containing 1–3 wt.% ZnO. By comparison to the more traditional multi-step process, the MB approach allowed the production of nanocomposites (films) having improved processing and enhanced properties: PLA chains displaying higher molecular weights, improved thermal stability, fine nanofiller distribution, and thermo-mechanical characteristic features, while the UV protection was confirmed by UV-vis spectroscopy measurements. The MB alternative is viewed as a promising flexible technique able to open new perspectives to produce more competitive multifunctional PLA–ZnO nanocomposites.     

Modification of poly(benzimidazole‐amide) nanocomposites by the incorporation of amine‐functionalized ZnO nanoparticles: Thermal and morphological characterization

Fabrication, characterization, and properties of novel poly(benzimidazole‐amide)/functionalized ZnO nanocomposites (PBIA/APS‐ZnO NCs) were investigated. At first, an aromatic PBA containing 3 imidazole units per repeat unit was synthesized by direct polycondensation of 1,3‐bis(5‐carboxylic acid‐2‐benzimidazole)benzene (BCAB) with 5‐(2‐benzimidazole)‐1,3‐phenylenediamine (DAMI) with good yield as a polymeric matrix. The periphery of zinc oxide nanoparticles (ZnO NPs) was modified with 3‐aminopropyltriethoxysilane (APS) to have a better dispersion NPs and enhancing interactions between nanoparticles and PBIA matrix. Different percentages of functionalized NPs (0, 4, 8, and 12 wt.%) were then embedded in PBA matrix through ultrasonic irradiation technique. Fourier transform infrared and thermo‐gravimetric analysis (TGA) confirmed that APS was successfully attached on the ZnO NP surface. The obtained NCs were characterized by means of Fourier transform infrared, X‐ray diffraction, scanning electron microscopy, and TGA. The TGA of the PBIA/APS‐ZnO NCs showed the enhancement in the thermal stability in comparison with the neat PBIA and that this increase is higher when the NP content increases. Scanning electron microscopy analyses of NCs revealed that the dispersion of APS‐ZnO NPs was uniformly done in the PBIA matrix.     

The synergistic reinforcing effects of halloysite nanotube particles and polyolefin elastomer-grafted-maleic anhydride compatibilizer on melt and solid viscoelastic properties of polylactic acid/ polyolefin elastomer blends

The effect of halloysite nanotube (HNTs) particles and polyolefin elastomer-graft-maleic anhydride (POE-g-MA) in the polylactic acid (PLA) and polyolefin elastomer (POE) blend with a constant weight percentage composition have been studied using the scanning electron microscopy, rheometry, dynamic mechanical thermal analysis (DMTA) as well as the thermogravimetric testing. Through these, it was found that the simultaneous presence of POE-g-MA and HNT significantly improves the melt and solid viscoelastic properties and thermal stability of PLA/POE. This improvement is attributed to the increased interactions and improved interfacial adhesion between the present components. The microscopic images of PLA/POE-g-MA/POE (80/8/12) blend containing 4 wt% HNT showed a microstructure similar to the interconnected morphology due to the enhanced compatibility and better dispersion of nanoparticles. The rheological behavior was significantly changed for the PLA/POE blend containing POE-g-MA and 4 wt% HNT. This dramatic increase in the rheological properties was consistent with the morphological results. Only one glass transition temperature was observed in the DMTA plot of PLA/POE-g-MA/POE blend, which was a sign of a homogeneous, fully compatible system. In addition, a very strong reinforcing effect of HNT particles was observed in the presence of POE-g-MA for the nanocomposites. Finally, the thermogravimetric analysis showed a completely different trend for thermal degradation of PLA/POE-g-MA/POE nanocomposite containing 4 wt% HNT, which could be an indication of microstructural development.     

Nanoperlite effect on thermal,rheological, surface and cellular properties of poly lactic acid/nanoperlite nanocomposites for multipurpose applications

In this study, poly lactic acid (PLA) based nanocomposites containing perlite nanoparticles were prepared by melt mixing method. Various characterization techniques were employed to evaluate the performance PLA/nanoperlite nanocomposites. The nanocomposites were characterized via FTIR to investigate the functional groups and chemical structure of the nanocomposites. Thermal properties of the nanocomposites, examined by DSC, showed that the increase of nano-perlite content in the PLA matrix reduces the crystallinity and melting temperature of the nanocomposites. The rheological studies indicated that both of storage and loss modulus are increased when the nanoperlite is added up to 5 wt%. However, the modulus is reduced in samples containing more than 5 wt% nanoparticle due to their agglomeration. The in-vitro degradation studies of the nanocomposites at elevated and normal temperatures showed hydrolytic degradation around 13–15 months. The surface behavior results implied that the water contact angle values exhibit a reducing trend when the nanoperlite content increases up to 3 wt%, which can be related to the decreased crystallinity of PLA and also to the hydrophilic nature of perlite. Moreover, the adhesion of osteoblast cells and their viability on an electrospun scaffold, made of optimized sample, showed the initial implications of potential applications of the nanocomposites in bone regeneration and biomedical applications. These multipurpose nanocomposites can also be used for packaging applications.     

Effect of ZnO nanoparticles on the thermal and mechanical properties of epoxy-based nanocomposite

Effect of ZnO nanoparticles particles on the mechanical properties and the curing behavior of an epoxy nanocomposite were studied. Nanocomposites were prepared using different loadings of pre-dispersed ZnO nanoparticles having an average size of 40 nm. The surface topography and morphology of the nanocomposites were studied using atomic force microscope (AFM). The mechanical properties of nanocomposites were studied using analytical techniques including dynamic mechanical thermal analysis and micro-Vickers hardness. Effects of ZnO nanoparticles on the curing behavior of these nanocomposites were investigated utilizing isothermal and non-isothermal differential scanning calorimeter techniques. In addition, chemical compositions of coatings containing different ZnO nanoparticles contents were studied using a Fourier transform inferred. It was found that, ZnO nanoparticles can effectively influence the mechanical properties of epoxy coating. In addition, lower curing degrees, and therefore crosslinking density of epoxy coating including higher ZnO nanoparticles were obtained. This effect was completely different at low and high loadings of the particles.     

Morphology‐controlled Fabrication of SnO2/ZnO Nanocomposites with Enhanced Photocatalytic Performance

In this work, a series of novel SnO₂/ZnO nanocomposites with different morphologies were fabricated via a facile hydrothermal technique followed by calcination in air. The morphological, structural and photocatalytic properties of the SnO₂/ZnO nanocomposites were studied using different methods. The results showed that the synthesized nanocomposites possessed crystal phases of wurtzite hexagonal phase ZnO and tetragonal rutile phase SnO₂. In addition, the morphologies of SnO₂/ZnO nanocomposites strongly depended on the molar ratios of Sn and Zn. Compared with ZnO and SnO₂, the SnO₂/ZnO nanocomposites exhibited considerably higher degradation efficiency for the photodegradation of methylene blue and quinolone antibiotics under mercury lamp irradiation. The SZ‐2 nanospheres exhibited the highest degradation efficiency of 95.81%, which was about 2.63 times higher than that of ZnO nanoparticles. Moreover, the trapping experiments confirmed that ˙OH played the dominant role in MB degradation. Finally, the charge carriers potential transfer pathway and photocatalytic degradation mechanism were put forward. This study provides an economical way to prepare hybrid nanocomposites with controlled morphology for practical applications in the photocatalytic degradation of organic dyes and residual antibiotics.     

Preparation and characterization of poly(amide-imide)/ZnO nanocomposites containing pendent benzoxazole and benzimidazole segments

In the present investigation, novel poly(amid-imide)/zinc oxide nanocomposites (PAI/ZnO NCs) containing benzoxazole and benzimidazole pendent groups with different amounts of modified zinc oxide nanoparticles (ZnO NPs) were successfully prepared via the ex situ method. Poly(amid-imide) (PAI) was prepared by direct polycondensation of 2-[3,5- bis(N-trimellitimidoyl)phenyl]benzoxazole (DCA) with 5-(2-benzimidazole)-1,3-phenylenediamine (DAMI) and provided the polymeric matrix with well-designed groups. The surface of ZnO NPs was functionalized with 3-aminopropyltriethoxysilane (APS) coupling agent to have a better dispersion and enhancing possible interactions of NPs with functional groups of polymer matrix. The amount of APS bonded to the ZnO surface was determined by thermogravimetric analysis. PAI/ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM). SEM analysis showed that the modified ZnO nanoparticles were homogeneously dispersed in polymer matrix. In addition, TGA data indicated an enhancement of thermal stability of the nanocomposite compared with the neat polymer.     

聚乳酸/氧化锌柱撑皂石纳米复合材料制备与性能及结构表征

通过微波水解法制备了ZnO柱撑皂石,并以其为加工助剂制备了聚乳酸(PLA)/ZnO柱撑皂石纳米复合材料.通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、对ZnO柱撑皂石及PLA/ZnO柱撑皂石纳米复合材料的结构进行了表征,并对其力学性能和热稳定性能进行了测试.微观结构分析表明,ZnO柱撑皂石呈现剥离状,并均匀分散在PLA基质中.力学性能研究表明0.3%ZnO柱撑皂石的加入有助于改善PLA复合材料的断裂伸长率.SEM分析表明PLA复合材料的断面发生明显改变,表现良好韧性;DSC结果显示纳米ZnO柱撑皂石可以降低复合材料的玻璃化转变温度、结晶温度,有助于提高PLA复合材料的结晶度,与XRD分析相吻合;热重分析表明ZnO柱撑皂石可以提高PLA复合材料的热稳定性.测试结果表明,ZnO柱撑皂石在PLA基质中起到了异相成核的作用,促进了PLA基质的结晶.     

Improvement in the light conversion efficiency of silicon solar cell by spin coating of CuO,ZnO nanoparticles and CuO/ZnO mixed metal nanocomposite material

Synthesis of pure Zinc oxide (ZnO), Copper oxide (CuO) nanoparticles (NPs) and their (ZnO/CuO) nanocomposites (NCs) in 1:1 M ratio were successfully prepared by co-precipitation method. The structural properties of the as synthesized nanoparticles and nanocomposite materials were investigated using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) techniques. Optical band-gap studies were done using UV–Visible absorption spectroscopy. Photovoltaic properties of pure ZnO NPs, CuO NPs and ZnO/CuO NCs coated over a single-crystalline silicon solar cell were carried out to compare improvement of light-conversion efficiency in coated solar cell. The maximum light conversion efficiencies were found to be of 8.02% for CuO (3 mg/ml concentration) and 7.28% for ZnO NPs (3 mg/ml concentration), whereas that of mixed metal nanocomposite CuO/ZnO NCs was found to be 7.62%. at very low concentration of 1 mg/ml. This indicates with low concentration of mixed metal NCs an improvement in light efficiency can be obtained. The enhancement in efficiency could be due to formation of p - n heterojunction by CuO/ZnO NCs composites which enhances the number of electrons and holes participating in conduction on the surface.     

ZnO nanopowders and their excellent solar light/UV photocatalytic activity on degradation of dye in wastewater

Low-cost and scalable preparation,high photocatalytic activity,and convenient recycle of Zn O nanopowders(NPs)would determine their practical application in purifying wastewater.In this contribution,ZnO NPs were scalably synthesized via the simple reaction of Zn powder with H_2O vapor in autoclave.The structural,morphological and optical properties of the samples were systematically characterized by X-ray diffraction,scanning electron microscopy,Fourier transform infrared spectra,transmission electron microscopy,Micro-Raman,photoluminescence,and ultraviolet-visible spectroscopy.The as-prepared Zn O NPs are composed of nanoparticles with 100–150 nm in diameter,and have a small Brunauer-Emmett-Teller surface area of 6.85 m~2/g.The formation of Zn O nanoparticles is relative to the peeling of H_2 release.Furthermore,the product has big strain-stress leading to the red-shift in the band gap of product,and shows a strong green emission centered at 515 nm revealing enough atomic defects in Zn O NPs.As a comparison with P25,the obtained dust gray Zn O NPs have a strong absorbance in the region of 200–700 nm,suggesting the wide wave-band utilization in sunlight.Based on the traits above,the Zn O NPs show excellent photocatalytic activity on the degradation of rhodamine B(Rh-B)under solar light irradiation,close to that under UV irradiation.Importantly,the Zn O NPs could be well recycled in water due to the quick sedimentation in themselves in solution.The low-cost and scalable preparation,high photocatalytic activity,and convenient recycle of Zn O NPs endow themselves with promising application in purifying wastewater.     

Preparation and characterization of novel polyimide/functionalized ZnO bionanocomposite for gas separation and study of their antibacterial activity

In the present investigation novel Polyimide/functionalized ZnO (PI/ZnO) bionanocomposites containing amino acid (Methionine) and benzimidazole pendent groups with different amounts of modified ZnO nanoparticles (ZnO NPs) were successfully prepared through ultrasonic irradiation technique. Due to the high surface energy and tendency for agglomeration, the surface ZnO NPs was modified by a coupling agent as 3- methacryloxypropyl-trimethoxysilane (MPS) to form MPS-ZnO nanoparticles. The ultrasonic irradiation effectively changes the rheology and the glass transition temperature and the crystallinity of the composite polymer. PI/ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM). TEM analysis showed that the modified ZnO nanoparticles were homogeneously dispersed in polymer matrix. The TGA results of PI/ZnO nanocomposites showed that the thermal stability is obviously improved the presence of MPS-ZnO NPs in comparison with the pure PI and that this increase is higher when the NP content increases. The permeabilities of pure H₂, CH₄, O₂, and N₂ gases through prepared membranes were determined at room temperature (25 °C) and 20 bar feed pressure. The membranes having 20% ZnO showed higher values of H₂ permeability, and H₂/CH₄ and H₂/N₂ ideal selectivities (the ratio of pair gas permeabilities) compared with other membranes. The antibacterial activity of bionanocomposite films was tested against gram-positive bacteria (Staphylococcus aureus and Bacillus subtilis) and gram-negative bacteria (Escherichia coli and Pseudomonas aeruginosa). Further, it was observed that antibacterial activity of the resulting hybrid biofilms showed somewhat higher for gram-positive bacteria compared to gram-negative bacteria.     

Synthesis of CuS and ZnO/Zn(OH)2 nanoparticles and their evaluation for in vitro antibacterial and antifungal activities

In this study, the copper sulfide nanoparticles (CuS‐NPs) and the zinc oxide/zinc hydroxide nanoparticles ((ZnO/Zn(OH)₂‐NPs) were synthesized by a simple and low‐cost method, and the synthesized nanoparticles were characterized and identified by UV–Vis, field emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM) and X‐ray diffraction (XRD). The antimicrobial activity of the CuS‐NPs and the ZnO/Zn(OH)₂‐NPs were examined by broth dilution to determine the minimal inhibitory concentration (MIC) of antibacterial agent required to inhibit the growth of a pathogen and the minimum bactericidal concentration (MBC) required to kill a particular bacterium. Agar disc diffusion method was used to determine the zone of inhibition. The nanoparticles demonstrated potent antibacterial activity against Klebsiella pneumonia (ATCC 1827), Acinetobacter baumannii (ATCC 150504), Escherichia coli (ATCC 33218) and Staphylococcus aureus (ATCC 25293). Antifungal activity against Aspergillus oryzae (PTCC 5164) was also obtained. The data obtained from antimicrobial activities by broth dilution and agar disc diffusion methods exhibited the CuS‐NPs were more effective than the ZnO/Zn(OH)₂‐NPs. A good correlation was observed between the data obtained by both methods.     

Antimicrobial,mechanical, optical and thermal properties of PVC/ZnO‐EDTA nanocomposite films

Covalent surface functionalization of synthesized ZnO nanoparticles (NP)s with ethylenediaminetetraacetic acid (EDTA) was successfully carried out. Modified ZnO‐EDTA NPs as a viable and inexpensive filler were incorporated into poly(vinyl chloride) PVC matrix after their chemical modification to investigate the agglomeration behavior. All prepared materials including modified NPs and PVC/ZnO‐EDTA nanocomposites (NC)s were analyzed by Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, X‐ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. Fabricated PVC/ZnO‐EDTA NCs were reported to have high transparency and improved mechanical properties compared with PVC. Modified ZnO and the fabricated NCs were shown to exhibit excellent antibacterial activity against two bacteria species: Escherichia coli and Staphylococcus aureus. The obtained NCs could be considered as self‐extinguishing materials on the basis of the LOI values. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis and Characterization of PANI/ZnO Nanocomposites

This paper presents our results on the successful fabrication of HCl‐doped polyaniline (PANI)/ZnO nanocomposites via an electrochemical synthesis route. Different weight percents of ZnO nanoparticles were uniformly dispersed in the PANI matrix. The interaction between the dispersed ZnO nanoparticle and PANI was studied using X‐ray diffraction, ultraviolet–visible absorption spectroscopy, photoluminescence (PL) spectroscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, thermogravimetry, and transmission electron microscopy. It is shown that the doping state of the PANI/ZnO nanocomposite is highly improved as compared to that of PANI. The dispersed PANI/ZnO nanocomposites exhibit enhanced PL behavior and thermal stability.     

离子液体中纤维素/纳米层状ZnO复合抗菌纤维的制备及性能

以表面活性剂十二烷基磺酸钠(SDS)为模板,Zn(NO_3)_2·6H_2O和NaOH为锌源和沉淀剂,通过改进的模板法在温和条件下制得纳米层状ZnO.以离子液体1-烯丙基-3-甲基咪唑氯盐([Amim]Cl)为溶剂,木浆纤维素和纳米层状ZnO为原料,采用溶液共混方法,通过干湿法纺丝制备了ZnO质量分数分别为3%,5%,7%及9%的纤维素/ZnO纳米复合纤维.采用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、场发射扫描电子显微镜(SEM)及热重分析(TG)等方法对纳米层状ZnO及纤维素/ZnO复合纤维进行了表征,并探讨了ZnO的加入对复合体系流变性的影响,同时对复合纤维进行了力学和抗菌性能测试.研究结果表明,所制备氧化锌纯度高,且呈现出重复周期为3.58 nm的层状结构,抗菌性能优异.纳米层状ZnO的加入提高了纤维素纤维的热稳定性和机械强度,同时赋予纤维对金黄色葡萄球菌和大肠杆菌的抑菌性.ZnO片层被纤维素链剥离,并均匀分散于纤维素/ZnO复合物中.ZnO的加入增大了纤维素溶液的黏度,当ZnO含量达到5%以上时,在整个频率范围内,弹性模量大于损耗模量,纳米粒子可稳定悬浮.     

Comparative study of acid yellow 119 adsorption onto activated carbon prepared from lemon wood and ZnO nanoparticles loaded on activated carbon

Activated carbon from lemon wood (AC) and ZnO nanoparticles loaded on activated carbon (ZnO‐NP‐AC) were prepared and their efficiency for effective acid yellow 199 (AY 199) removal under various operational conditions was investigated. The dependence of removal efficiency on variables such as AY 199 concentration, amount of adsorbent and contact time was optimized using response surface methodology and Design‐Expert. ZnO nanoparticles and ZnO‐NP‐AC were studied using various techniques such as scanning electron microscopy, X‐ray diffraction and energy‐dispersive X‐ray analysis. The optimum pH was studied using one‐at‐a‐time method to achieve maximum dye removal percentage. Small amounts of the proposed adsorbents (0.025 and 0.025 g) were sufficient for successful removal of AY 199 in short times (4.0 and 4.0 min) with high adsorption capacity (85.51 and 116.29 mg g^?1 for AC and ZnO‐NPs‐AC, respectively). Fitting the empirical equilibrium data to several conventional isotherm models at optimum conditions indicated the appropriateness of the Langmuir model with high correlation coefficient (0.999 and 0.978 for AC and ZnO‐NPs‐AC, respectively) for representation and explanation of experimental data. Kinetics evaluation of experiments at various time intervals revealed that adsorption processes can be well predicted and fitted by pseudo‐second‐order and Elovich models. This study revealed that the combination of ZnO nanoparticles and AC following simple loading led to significant improvement in the removal process in short adsorption time which was enhanced by mixing the media via sonication.     

Synthesis,characterization of layered double hydroxide‐poly(methylmethacrylate) graft copolymers via activators regenerated by electron transfer for atom transfer radical polymerization and its effect on the performance of poly(lactic acid)

Layered double hydroxide‐poly(methylmethacrylate) (LDH‐PMMA) graft copolymers were prepared via activators regenerated by electron transfer for atom transfer radical polymerization. The results showed that the hydrophobicity of LDH‐PMMA was improved by the incorporation of hydrophilic groups. Moreover, poly(lactic acid) (PLA)/LDH‐PMMA nanocomposites were prepared by melt blending to enhance the performances of PLA. The crystallization and mechanical properties of the PLA/LDH‐PMMA nanocomposites were studied by differential scanning calorimetry, tensile testing, and polarized optical microscopy, respectively. Results of mechanical testing showed that the tensile strength, elongation at break, and impact strength of PLA/LDH‐PMMA nanocomposites were increased by 5.64%, 37.95%, and 49.70%, respectively, compared with PLA. The differential scanning calorimetry results indicated that LDH‐PMMA eliminated the cold crystallization of PLA matrix and improved the crystallinity of PLA by 37.26%. The polarized optical microscopy of PLA/LDH‐PMMA nanocomposites demonstrated that LDH‐PMMA increased the crystallization rate of PLA. It was also found that the rheological behaviors of the PLA nanocomposites were significantly enhanced. Based on these results, a new choice for modified LDHs was provided and used as a nucleating agent to improve the properties of PLA.     

Nanoflower-like composites of ZnO/SiO2 synthesized using bamboo leaves ash as reusable photocatalyst

In this study, the synthesis of ZnO/SiO₂ nanocomposites using bamboo leaf ash (BLA) and tested their photocatalytic activity for rhodamine B decolorization have been conducted. The nanocomposites were prepared by the sol–gel reaction of zinc acetate dihydrate, which was used as a zinc oxide precursor, with silica gel obtained from the caustic extraction of BLA. The effect of the Zn content (5, 10, and 20 wt%) on the physicochemical characteristics and photocatalytic activity of the nanocomposites was investigated. The results of X-ray diffraction, scanning electron microscopy, gas sorption, and transmission electron microscopy characterization confirmed the mesoporous structure of the composites containing nanoflower-like ZnO (wurtzite) nanoparticles of 10–30 nm in size dispersed on the silica support. Further, the nanocomposites were confirmed to be composed of ZnO/SiO₂ by X-ray photoelectron spectroscopy analysis. Meanwhile, diffuse-reflectance UV–visible spectrophotometry analysis of the nanocomposites revealed band gap energies of 3.38–3.39 eV. Of the tested nanocomposites, that containing 10 wt% Zn exhibited the highest decolorization efficiency (99%) and fastest decolorization rate. In addition, the degradation efficiencies were not reduced significantly after five repeated runs, demonstrating the reusability of the nanocomposite catalysts. Therefore, the ZnO/SiO₂ nanocomposite obtained from BLA is a promising reusable photocatalyst for the degradation of dye-polluted water.