Novel fluorosilicone thermoplastic vulcanizates prepared via core‐shell dynamic vulcanization: Effect of fluororubber/silicone rubber ratio on morphology,crystallization behavior,and mechanical properties

Recently, we have reported a novel core‐shell dynamic vulcanization method to prepare poly(vinylidene fluoride) (PVDF)/fluororubber (FKM)/silicone rubber (SR) thermoplastic vulcanizates (TPVs) with cross‐linked rubber core‐shell particles. However, the shell thickness on the properties has not been studied in detail. Herein, these PVDF‐based TPVs different FKM‐shell thickness were prepared by changing FKM/SR ratios. The effect of FKM‐shell/SR‐core ratio on morphology, crystallization, and mechanical properties of the ternary TPVs was studied. The results showed that the FKM shell had more positive effect on interfacial‐induced crystallization behavior than the SR core due to its better compatibility with PVDF. When the FKM/SR ratio was <1, FKM was not enough to encapsulate SR completely, which resulted in the formation of imperfect core‐shell structure. However, when the FKM/SR ratio was >1, perfect core‐shell structure was formed. Therefore, the mechanical properties improved with increasing FKM content; especially, a remarkable improvement was observed when FKM/SR ratio was >1. This study could provide more information for the design of TPVs with core‐shell structure.     

Preparation of polypropylene/ethylene‐propylene‐diene terpolymer/nitrile rubber ternary thermoplastics vulcanizates with good mechanical properties and oil resistance by core‐shell dynamic vulcanization

As the most successful commercialized thermoplastic vulcanizates (TPVs), polypropylene (PP)/ethylene propylene rubber (EPDM) TPVs exhibit poor oil resistance. In this work, we prepared PP/EPDM/butadiene acrylonitrile rubber (NBR) ternary TPVs with good oil resistance using core‐shell dynamic vulcanization. According to the theoretical analysis of the spreading coefficient and the transmission electron microscopy results, the rubber phases exhibited a special core‐shell structure, in which the cross‐linkedNBR‐core was encapsulated by the EPDM‐shell. The core‐shell structure effectively improved the interfacial compatibility between PP and NBR phase as the EPDM‐shell could avoid the direct contact of them, thus improving the mechanical properties of the TPVs. For example, the PP/EPDM/NBR (40/30/30) ternary TPV showed enhanced tensile strength of 12.57 MPa, compared with 10.71 MPa of PP/EPDM (40/60) TPV and 11.11 MPa of PP/NBR (40/60) TPV, respectively. Moreover, the oil resistance of the TPVs was also improved. Compared with PP/EPDM TPV, the change rates in mass, volume, tensile strength and elongation at break of PP/EPDM/NBR TPV after oil immersion decreased by 42.18%, 48.69%, 52.68% and 28.77%, respectively.     

Preparation and thermal properties of a novel core‐shell structure flame‐retardant copolymer

In order to improve the flame retardancy of polystyrene (PS), a phosphorus and nitrogen comonomer, named AC₂NP₂, was synthesized and then incorporated into various amounts of PS by seeded emulsion polymerization. The modified methacrylate (AC₂NP₂) was used as the core phase, the styrene as the shell phase, then flame‐retardant effect copolymers with core‐shell structure were prepared successfully. The particle size was ranged from 40 to 60 nm, and the structure and properties of the copolymers were characterized in detail. Notably, despite a few amounts of the AC₂NP₂ units in the copolymers, all the copolymers exhibited significantly enhanced thermal stability and reduced flammability as compared with pure PS. Furthermore, from differential scanning calorimetry test, it was observed that the glass transition temperature was tinily influenced with the incorporation of commoner. The incorporation of P‐N comonomer into PS backbone did not lead to negative effect on the glass transition behavior of PS.     

Probing the surfaces of core‐shell and hollow nanoparticles by solvent relaxation NMR

Measurement of the spin–spin NMR relaxation time (or its inverse, the rate) of water molecules in aqueous nanoparticle dispersions has become a popular approach to probe of the nature and structure of the particle surface and any adsorbed species. Here, we report on the characterisation of aqueous dispersions of hollow amorphous nanoparticles that have two liquid accessible surfaces (inner cavity surface and outer shell surface) plus the solid (silica) and core‐shell (titania–silica) nanoparticle precursors from which the hollow particles have been prepared. In all cases, the observed water relaxation rates scale linearly with particle surface area, with the effect being more pronounced with increasing levels of titania present at the particle surface. Two distinct behaviours were observed for the hollow nanoparticles at very low volume fractions, which appear to merge with increasing surface area (particle concentration). Herewith, we further show the versatility of solvent NMR spectroscopy as a probe of surface character.     

Fabrication of novel core–shell PLGA and alginate fiber for dual‐drug delivery system

Biodegradable fibers for the controlled delivery of anti‐inflammatory agent dexamethasone were developed and studied. Mono and core–shell structure fiber are prepared by wet‐spinning solutions of hydrophobic poly (lactide‐co‐glycolide) and hydrophilic alginic acid shell. The two model drugs, dexamethasone and dexamethasone‐21‐phosphate, were entrapped in core and shell, respectively. These fibers were characterized in terms of morphology, diameters, mechanical properties, in vitro degradation, and drug release. The optical microscopy and scanning electron microscopy photos revealed directly that fibers possessed core–shell structure. The release of dexamethasone and dexamethasone‐21‐phosphate was investigated, and the results showed that alginate shell retarded dexamethasone release significantly in both early and late stages. The core–shell structure fiber release shows a two stage release of dexamethasone and dexamethasone‐21‐phosphate with distinctly different release rates, and minimal initial burst release is observed. The results indicated that the prepared fibers are efficient carrier for both types of dexamethasone. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis and mechanical strength of a novel double network nanocomposite hydrogel with core‐shell structure

A novel poly[(dimethylimino)(2‐hydroxy‐1,3‐propanedily)chloride]/Laponite/polyacrylic acid (PDMIHPC/Clay/PAA) hydrogel was synthesized by two‐step solution polymerization combining the strategies of both nanocomposite (NC) gels and double network (DN) gels. The chemical composition and core‐shell structure of the hydrogels were confirmed by Fourier transform infrared (FTIR) and transmission electron microscopy (TEM). The mechanical strength was examined by varying the reaction temperature, PDMIHPC/Clay composite dose, N,N′‐methylenebisacrylamide (MBAM) dose and water content. When the reaction temperature was 35°C, PDMIHPC/Clay composite/AA is 1:10 and MBAM dose was 0.050 wt% (based on the weight of AA), the novel hydrogel achieved a best compressive strength of 100.05 KPa with a water content of 98.8%. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation and characterization of polytetrafluoroethylene‐polyacrylate core–shell nanoparticles

Polytetrafluoroethylene (PTFE)‐polyacrylate core–shell nanoparticles were produced by using PTFE micropowder and acrylate via seeded emulsion polymerization in the presence of fluorosurfactant. The properties of emulsion under various polymerization conditions were investigated and optimized. The chemical composition of the PTFE‐polyacrylate nanoparticles was characterized by Fourier‐transform infrared spectrometry (FTIR). The particle size and core–shell structure of the resulting PTFE‐polyacrylate nanoparticles were confirmed by transmission electron microscopy (TEM). Wettability of the PTFE‐polyacrylate core–shell particles was higher than the pristine PTFE. The formation of this kind of PTFE‐polyacrylate core–shell nanoparticles could improve the compatibility of PTFE with other materials because PTFE is covered by polyacrylate shell, which make them promising in various fields. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation of 1,2,4,5‐tetrasubstituted imidazoles over magnetic core–shell titanium dioxide nanoparticles

Magnetic core–shell titanium dioxide nanoparticles (Fe₃O₄@SiO₂@TiO₂) were applied for the efficient preparation of 1,2,4,5‐tetrasubstituted imidazole derivatives by the one‐pot multi‐component condensation of benzil with aldehydes, primary amines and ammonium acetate under solvent‐free conditions. The catalyst was synthesized and studied using several techniques including X‐ray diffraction, transmission electron microscopy, field‐emission scanning electron microscopy and energy‐dispersive X‐ray spectroscopy. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of gel‐silica/ammonium polyphosphate core‐shell flame retardant and properties of polyurethane composites

A novel intumescent gel‐silica/ammonium polyphosphate core‐shell flame retardant (MCAPP), which contains silicon, phosphorus, and nitrogen, has been prepared by in situ polymerization. The structure of MCAPP was characterized by Fourier transform infrared (FTIR) and X‐ray photoelectron spectroscopy (XPS). The properties of MCAPP were investigated by water solubility, hydrophilicity, and morphological determination. The flame retardancy and thermal stability of polyurethane (PU) composite with MCAPP were evaluated by limiting oxygen index (LOI), UL‐94 test, cone calorimetry, and thermogravimetric analysis (TGA). The results showed that MCAPP could decrease the heat release rate (HRR) and increase the thermal stability of PU materials greatly. Finally, water‐resistant properties of PU/FR composites were also studied. Copyright © 2010 John Wiley & Sons, Ltd.     

Gold‐loading magnetic core–shell organic/inorganic nanocomposites: facile preparation and multiple properties

Magnetic composite nanospheres (MCS) were first prepared via mini‐emulsion polymerization. Subsequently, the hybrid core–shell nanospheres were used as carriers to support gold nanoparticles. The as‐prepared gold‐loading magnetic composite nanospheres (Au‐MCS) had a hydrophobic core embed with γ‐Fe₃O₄ and a hydrophilic shell loaded by gold nanoparticles. Both the content of γ‐Fe₃O₄ and the size of gold nanoparticles could be controlled in our experiments, which resulted in fabricating various materials. On one hand, the Au‐MCS could be used as a T₂ contrast agent with a relaxivity coefficient of 362 mg^?1 ml S^?1 for magnetic resonance imaging. On the other hand, the Au‐MCS exhibited tunable optical‐absorption property over a wavelength range from 530 nm to 800 nm, which attributed to a secondary growth of gold nanoparticles. In addition, dynamic light scattering results of particle sizing and Zeta potential measurements revealed that Au‐MCS had a good stability in an aqueous solution, which would be helpful for further applications. Finally, it showed that the Au‐MCS were efficient catalysts for reductions of hydrophobic nitrobenzene and hydrophilic 4‐nitrophenol that could be reused by a magnetic separation process. Copyright © 2014 John Wiley & Sons, Ltd.     

One‐pot synthesis of composite microspheres with core‐shell structure

One‐pot synthesis of thermoresponsive magnetic composite microspheres with a poly(N‐isopropylacrylamide) (PNIPAM) shell and a Fe₃O₄ core is demonstrated. Temperature sensitivity of PNIPAM was adopted to design the novel synthesis pathway. The as‐prepared composite microspheres have an obvious core‐shell structure with a mean size of approximately 250 nm. The Fe₃O₄ core is approximately 5 nm and the thickness of the PNIPAM shell is approximately 10 nm. The content of Fe₃O₄ in the composite microspheres can be controlled by this method. The composite microspheres experience a swelling and shrinking process in water by adjusting the temperature below and above the lower critical solution temperature (LCST) around 32 °C. These microspheres also show fine response to an external magnetic field. This work presents a platform to synthesize organic/inorganic composite microspheres in a facile and efficient approach. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2702–2708     

Preparation and properties of thermoresponsive and conductive composite fibers with core‐sheath structure

In this research, thermoresponsive and conductive fibers with core‐sheath structure were fabricated by coaxial electrospinning. For preparing the spinning sheath solution, poly‐(N‐isopropylacrylamide‐co‐N‐methylolacrylamide) (PNN) copolymer having thermoresponsive and cross‐linkable properties was synthesized by free‐radical polymerization using redox initiators; it was then mixed with the conductive poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) at different weight ratios in water. On the other hand, poly(butyl acrylate‐co‐styrene) (PBS) copolymer synthesized by emulsion polymerization was dissolved in chloroform and used as the spinning core solution. After electrospinning, the fibers were treated at 110 °C for 1 h to cross‐link the PNN portion in the sheath for strengthening the fibers. Well‐defined core‐sheath fibers were observed from SEM pictures; the outside and inside (core) diameters were 568 ± 24 and 290 ± 40 nm, respectively, as determined from TEM pictures. The fiber mats were further doped by DMSO to enhance their conductivity. For the fiber mat with the weight ratio of PEDOT:PSS/PNN at 0.20 in the sheath, its surface conductivity could reach 29.4 S/cm. In addition, the fiber mats exhibited thermoresponsive properties that both swelling ratio and electric resistance decreased with temperature. Furthermore, the fiber mats exhibited improved flexibility as evaluated via bending test. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1299–1307     

Synthesis and characterization of fluorine‐containing polyacrylate latex with core–shell structure by UV‐initiated seeded emulsion polymerization

A core–shell fluorine‐containing polyacrylate emulsion was successfully prepared by UV‐initiated seeded emulsion polymerization in two stages in the presence of two photoinitiators. The water‐soluble photoinitiator for the core polymerization and the oil‐soluble photoinitiator was used for the shell polymerization. Both of the two stage polymerizations could be completed within 15 min and displayed a conversion above 94%. The emulsion and the films were characterized by Fourier transformed infrared spectrometry, transmission electron microscopy, dynamic light scattering, X‐ray photoelectron spectroscopy (XPS), contact angle (CA), and thermogravimetry analysis, respectively. The analysis results indicated that the fluorine‐containing latex particles had very small particle size (40 nm) with a core–shell structure and a narrow particle size distribution. XPS analysis revealed that a gradient concentration of fluorine excited in fluorine‐containing emulsion film from the film–air interface to the film–glass interface. In addition, the film formed from the fluorine‐containing emulsion exhibited not only higher thermal stability but also better hydrophobicity than that of the fluorine‐free emulsion. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and ferromagnetic properties of Ni0.5Zn0.5Fe2O4/polyaniline core–shell nanocomposites

Magnetic Ni_0.5Zn_0.5Fe₂O₄‐crosslinked polyaniline composites with a core–shell structure were prepared in the presence of Ni_0.5Zn_0.5Fe₂O₄ magnetic powder in a toluene solution containing iron chloride as a surfactant and dopant. Structural characterization by Fourier transform infrared, X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy proved that Ni_0.5Zn_0.5Fe₂O₄ in the composites was responsible for the ferromagnetic behavior of the composites. The effects of the polyaniline and temperature on the magnetic properties of the Ni_0.5Zn_0.5Fe₂O₄/polyaniline composites were studied with electron paramagnetic resonance and superconducting quantum interference device techniques. A clear evolution from ferromagnetic resonance to electron paramagnetic resonance was observed as a function of temperature, which was related to the passage through the Curie point (～420 K). The magnetic properties of the resulting composites showed ferromagnetic behavior, such as high‐saturated magnetization (saturation magnetization = 35–39 emu/g), low coercive force (coercivity = 22–28 G), and low blocking temperatures (～23 K). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2657–2664, 2006     

Cyclodextrin‐overhanging hyperbranched core‐double‐shell miktoarm architectures: Synthesis and gradient stimuli‐responsive properties

We report the synthesis and gradient stimuli‐responsive properties of cyclodextrin‐overhanging hyperbranched core‐double‐shell miktoarm architectures. A ionic hyperbranched poly(β‐cyclodextrin) (β‐CD) core was firstly synthesized via a convenient “A₂+B₃” approach. Double‐layered shell architectures, composed of poly(N‐isopropyl acrylamide) (PNIPAm) and poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) miktoarms as the outermost shell linked to poly(N,N‐diethylaminoethyl methacrylate) (PDEAEMA) homoarms which form the inner shell, were obtained by a sequential atom transfer radical polymerization (ATRP) and parallel click chemistry from the modified hyperbranched poly(β‐CD) macroinitiator. The combined characterization by ¹H NMR, ¹³C NMR, ¹H‐²⁹Si heteronuclear multiple‐bond correlation (HMBC), FTIR and size exclusion chromatography/multiangle laser light scattering (SEC/MALLS) confirms the remarkable hyperbranched poly(β‐CD) core and double‐shell miktoarm architectures. The gradient triple‐stimuli‐responsive properties of hyperbranched core‐double‐shell miktoarm architectures and the corresponding mechanisms were investigated by UV–vis spectrophotometer and dynamic light scattering (DLS). Results show that this polymer possesses three‐stage phase transition behaviors. The first‐stage phase transition comes from the deprotonation of PDEAEMA segments at pH 9–10 aqueous solution under room temperature. The confined coil‐globule conformation transition of PNIPAm and PDMAEMA arms gives rise to the second‐stage hysteretic cophase transition between 38 and 44 °C at pH 10. The third‐stage phase transition occurs above 44 °C at pH = 10 attributed to the confined secondary conformation transition of partial PDMAEMA segments. This cyclodextrin‐overhanging hyperbranched core‐double‐shell miktoarm architectures are expected to solve the problems of inadequate functionalities from core layer and lacking multiresponsiveness for shell layers existing in the dendritic core‐multishell architectures. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Enhanced dielectric properties of polymer composite films induced by encapsulated MWCNTs with a one core‐two shell structure

Multiwalled carbon nanotubes (MWCNTs) can endow high dielectric constant to polymer‐based composites. However, the accompanying poor dispersion of MWCNTs and high dielectric loss for composites severely limit their application in dielectric field. Herein, a modified acid‐treated MWCNTs encapsulated by the polyaniline/poly(sodium 4‐styrenesulfonate) layers (aMWCNTs@PANI‐PSS) with a one core‐two shell structure was fabricated by in situ polymerization followed by electrostatic self‐assembly technique. Furthermore, the composite films based on aMWCNTs@PANI‐PSS/poly(vinylidenefluoride‐hexaflouropropylene) (PVDF‐HFP) were fabricated by a solution‐casting method. An ultrathin insulating PSS shell is wrapped onto aMWCNTs@PANI, resulting in the improvement of dispersibility for aMWCNTs@PANI and the decrease of dielectric loss for composite films. When the content of aMWCNTs@PANI‐PSS is 5.0 wt %, the dielectric constant of aMWCNTs@PANI‐PSS/PVDF‐HFP reaches 430 (100 Hz), which is about 55 times of pure PVDF‐HFP and 1.7 times of aMWCNTs@PANI/PVDF‐HFP (247). Besides, the responding dielectric loss of aMWCNTs@PANI‐PSS/PVDF‐HFP composite film is only 0.67, much lower than that of aMWCNTs@PANI/PVDF‐HFP (25) and aMWCNTs/PVDF‐HFP (3185). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 948–956     

Preparation of magnetic Fe3O4/P (GMA‐DVB)‐PEI/Pd highly efficient catalyst with core‐shell structure

In this paper, a simple route for palladium (Pd) nanoparticles attached to the surface of hollow magnetic Fe₃O₄/P (GMA‐DVB)‐polyethyleneimine (PEI) microspheres was established. Due to the large amount of imidogen groups and tertiary amine groups presenting in the PEI, Pd²⁺ ions could be anchored to the support by complexation with a polyfunctional organic ligand. Thereafter, a magnetic Pd catalyst having a high loading amount and good dispersibility was obtained by reducing Pd²⁺ ions. Afterwards, the prepared catalyst was characterized by TEM, SEM, FTIR, XRD, TGA, VSM, and UV–vis in detail. Ultimately, their catalytic activity was evaluated using the reduction of 4‐nitrophenol (4‐NP). Research showed that the Fe₃O₄/P (GMA‐DVB)‐PEI/Pd catalyst possessed high catalytic performances for the reduction of 4‐NP with a conversion rate of 98.43% within 540 s. Furthermore, the catalyst could be easily recovered and reused at least for nine successive cycles.     

Tracer diffusion properties of core–shell latex films studied by photoinduced grating relaxation

This article reports the application of the Photo‐Induced Grating Relaxation technique (also known as Forced Rayleigh Scattering) to investigate the dynamics of films prepared from structured core–shell latex particles via the transport property of the photochromic tracer molecule Aberchrome 540®. The core–shell particles were prepared with a fluoropolymer core (immiscible and impenetrable to the tracer) and a poly(butyl methacrylate) shell. The incompletely dried films (with residual water) manifest their spatial heterogeneity via non‐Fickian behavior (spatial scale‐ dependent apparent diffusion coefficient). The diffusion data was interpreted using the two‐state diffusion model, previously developed to describe the tracer diffusion in latex films without any core–shell structure. In contrast to dry latex films made from homogeneous particles, where one observes Fickian diffusion indicative of a homogeneous polymer film, we find that the lattice of fluoropolymer cores leads to a length scale dependent diffusion coefficient for the tracer. This effect can be interpreted as microscopic evidence for a strain hardening effect due to the presence of a hardened layer of matrix polymer (= shell) surrounding the core, which act as nanofillers. This strain hardening effect could be quantified within the two‐state diffusion model in terms of tracer diffusion coefficients and root mean squared displacements. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2823–2834, 2007     

Preparation and application of a novel core–shell‐particle‐supported zirconocene catalyst

The use of functional groups bearing silica/poly(styrene‐co‐4‐vinylpyridine) core–shell particles as a support for a zirconocene catalyst in ethylene polymerization was studied. Several factors affecting the behavior of the supported catalyst and the properties of the resulting polymer, such as time, temperature, Al/N (molar ratio), and Al/Zr (molar ratio), were examined. The conditions of the supported catalyst preparation were more important than those of the ethylene polymerization. The state of the supported catalyst itself played a decisive role in both the catalytic behavior of the supported catalyst and the properties of polyethylene (PE). IR and X‐ray photoelectron spectroscopy were used to follow the formation of the supports. The formation of cationic active species is hypothesized, and the performance of the core–shell‐particle‐supported zirconocene catalyst is discussed as well. The bulk density of the PE formed was higher than that of the polymer obtained from homogeneous and polymer‐supported Cp₂ZrCl₂/methylaluminoxane catalyst systems. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2085–2092, 2001     

Preparation of poly(methyl methacrylate)–poly(acrylonitrile‐co‐butadiene) core–shell nanoparticles

Poly(methyl methacrylate)–poly(acrylonitrile‐co‐butadiene) (PMMA–NBR) core–shell structured nanoparticles were prepared using a two‐stage semibatch microemulsion polymerization system with PMMA and NBR as the core and shell, respectively. The Gemini surfactant 12‐3‐12 was used as the emulsifier and found to impose a pronounced influence on the formation of core–shell nanoparticles. The spherical morphology of core–shell nanoparticles was observed. It was found that there exists an optimal MMA addition amount, which can result in the minimized size of PMMA–NBR core–shell nanoparticles. The formation mechanism of the core–shell structure and the interaction between the core and shell domains was illustrated. The PMMA–NBR nanosize latex can be used as the substrate for the following direct latex hydrogenation catalyzed by Wilkinson's catalyst to prepare the PMMA–HNBR (hydrogenated NBR) core–shell nanoparticles. The hydrogenation rate is rapid. In the absence of any organic solvent, the PMMA–HNBR nanoparticles with a size of 30.6 nm were obtained within 3 h using 0.9 wt % Wilkinson's catalyst at 130 °C under 1000 psi of H₂. This study provides a new perspective in the chemical modification of NBR and shows promise in the realization of a “green” process for the commercial hydrogenation of unsaturated elastomers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012