Preparation of phosphorus‐containing phenolic resin and its application in epoxy resin as a curing agent and flame retardant

For the sake of improving the flame retardancy of epoxy resin (EP), a novel phosphorus‐containing phenolic resin (PPR) synthesized in our group instead of conventional phenolic resin (PR) was used to cure EP in the present research. The curing processes and the corresponding crosslinking structure and mechanical performance were investigated by differential scanning calorimeter and dynamic mechanical thermal analysis. Because of the introduction of flame‐retarding elements including P and Si, PPR exhibited higher charring capacity in the condensed phase, which is helpful to construct a char layer of higher quality. Correspondingly, PPR‐cured EP displayed remarkably improved flame retardance as compared to conventional PR‐cured EP through the related evaluations including limiting oxygen index, vertical burning test, and microscale combustion colorimeter. As a multifunction agent, it is believable that PPR possesses potential commercial value to prepare flame‐retardant EP with high performance.     

六苯氧基环三磷腈的热解及其对环氧树脂的阻燃机理

采用极限氧指数仪和锥形量热仪测试了以六苯氧基环三磷腈(HPCP)阻燃环氧树脂的燃烧性能,结果显示,与纯环氧树脂相比,阻燃环氧树脂的极限氧指数值(LOI)明显提高、热释放速率峰值(pk-HRR)和总热释放量(THR)明显下降、环氧树脂的点燃时间提前以及分解速度加快.采用热失重(TGA)、热重红外联用(TGA-FTIR)、X射线光电子能谱(XPS)和热裂解气相色谱质谱联用(Py-GC/MS)研究了HPCP及其阻燃环氧树脂的热解路线和阻燃机理.结果表明,在阻燃环氧树脂过程中,一方面,HPCP分子中的苯氧基团首先解离并发生歧化反应,由此产生的苯氧基及其歧化产物的焠灭效应在环氧树脂中发挥气相阻燃作用,剩余的磷腈环和苯环基团会进一步裂解产生小分子碎片;另一方面,环氧树脂基体在HPCP的作用下提前分解,产生了基于双酚A结构的大分子碎片并在HPCP裂解产物作用下加速炭化,从而使更多的基体组分以残炭的形式被固定在凝聚相中,提高了阻燃环氧树脂的残炭产率,发挥了凝聚相阻燃作用.     

A vanillin-derived flame retardant based on 2-aminopyrimidine for enhanced flame retardancy and mechanical properties of epoxy resin

In order to give epoxy resin good flame retardance, a novel bio-based flame retardant based on 2-aminopyrimidine (referred to as VAD) was synthesized from renewable vanillin as one of the starting materials. Its structure was confirmed by NMR and mass spectra. The epoxy resins containing VAD were prepared by utilizing 4,4-diaminodiphenylmethane (DDM) as a co-curing agent, and their flame-retardant, mechanical and thermal properties and corresponding mechanisms were studied. VAD accelerated the cross-linking reaction of DDM and E51 (diglycidyl ether of bisphenol A). 12.5 wt% VAD made the epoxy resin achieve UL-94 V-0 rating and its limited oxygen index (LOI) value increase from 22.4% to 32.3%. The cone calorimetric testing results revealed the decline in the values of total heat release (THR) and peak of heat release rate (pk-HRR) and the obvious enhancement of residue yield. A certain amount of VAD enhanced the flame inhibition, charring and barrier effects, resulting in good flame retardance of the epoxy resin. Furthermore, the tensile strength, flexural strength and flexural modulus of the epoxy resin with 12.5 wt% loading of VAD were 6.5%, 14.9%, 15.2% higher than those of EP, indicating the strengthening effect of VAD. This work guarantees VAD to be a promising flame retardant for enhancing the fire retardancy of epoxy resin without compromising its mechanical properties.     

A flame‐retardant phosphate and cyclotriphosphazene‐containing epoxy resin: Synthesis and properties

A novel flame‐retardant epoxy resin, (4‐diethoxyphosphoryloxyphenoxy)(4‐glycidoxyphenoxy)cyclotriphosphazene (PPCTP), was prepared by the reaction of epichlorohydrin with (4‐diethoxyphosphoryloxyphenoxy)(4‐hydroxyphenoxy)cyclotriphosphazene and was characterized by Fourier transform infrared, ³¹P NMR, and ¹H NMR analyses. The epoxy resin was further cured with diamine curing agents, 4,4′‐diaminodiphenylmethane (DDM), 4,4′‐diaminodiphenylsulfone (DDS), dicyanodiamide (DICY), and 3,4′‐oxydianiline (ODA), to obtain the corresponding epoxy polymers. The curing reactions of the PPCTP resin with the diamines were studied by differential scanning calorimetry. The reactivities of the four curing agents toward PPCTP were in the following order: DDM > ODA > DICY > DDS. In addition, the thermal properties of the cured epoxy polymers were studied by thermogravimetric analysis, and the flame retardancies were estimated by measurement of the limiting oxygen index (LOI). Compared to a corresponding Epon 828‐based epoxy polymer, the PPCTP‐based epoxy polymers showed lower weight‐loss temperatures, higher char yields, and higher LOI values, indicating that the epoxy resin prepared could be useful as a flame retardant. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 972–981, 2000     

Synthesis and characterization of P/Si flame retardant and its application in epoxy systems

In this report, a novel phosphorus/silicon‐containing reactive flame retardant, hexa(3‐triglycidyloxysilylpropyl)triphosphazene (HGPP), was synthesized and characterized by Fourier transform infrared spectrometry and nuclear magnetic resonance spectra (¹H, ³¹P, and ²⁹Si), respectively. To prepare cured epoxy, HGPP had been co‐cured with diglycidyl ether of bisphenol‐A (DGEBA) via 4,4‐diaminodiphenylsulfone as a curing agent. The mechanical, thermal, and flame retardant properties of the cured epoxy were evaluated by dynamic mechanical analysis, thermogravimetric analysis, and limiting oxygen index (LOI). According to these results, it could be found that incorporation of HGPP in the cured epoxy system showed good thermal stability, high LOI values, and high char yield at high temperature. As moderate loading of HGPP in the epoxy system, its storage modulus and glass transition temperature were higher than those of neat DGEBA. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation and characterization of microencapsulated LDHs with melamine‐formaldehyde resin and its flame retardant application in epoxy resin

Layered double hydroxides (LDHs) are emerging as a new and green high‐efficient flame retardant. But LDHs aggregate seriously because of their hydrophilicity, which affect deeply the mechanical and flame retardant properties of their composites. For the first time in this paper, microencapsulated LDHs (MCLDHs) with melamine‐formaldehyde (MF) resin were prepared by microencapsulation technology to enhance their compatibility and dispersion within epoxy resin (EP). The mechanical and flame retardant performances of EP/MCLDH composite were studied by comparing with EP/LDH composite. Results showed that the water contact angle of MCLDHs increased from 8.9° to 122.1°, which indicated good compatibility. The particle size of MCLDHs decreased sharply, and more than one‐third were up to submicron scale, which can be conducive to dispersion. Moreover, the tensile strength and elongation at break of EP/MCLDHs with different flame retardant contents were higher than those of EP/LDHs. And the addition of MCLDHs increased the glass transition temperature (Tg) of EP/MCLDHs, which meant a strong interfacial interaction. Besides, compared with EP/LDHs, the limiting oxygen index values of EP/MCLDHs were higher, and its peak of heat release rate and total heat release decreased by 16.3% and 5.5% respectively. EP/MCLDHs achieved from V‐1 to V‐0 rate with the increasing content of MCLDHs from 20% to 30%, while LDHs/EP never passed tests. In the process of heating, H₂O, CO₂, and NH₃ released from MCLDHs formed gaseous phase, and the remaining dense char layers and oxides produced condensed phase, which played an important role in inhibiting combustion.     

Highly efficient multielement flame retardant for multifunctional epoxy resin with satisfactory thermal,flame‐retardant,and mechanical properties

Multifunctional epoxy resins with excellent, thermal, flame‐retardant, and mechanical properties are extremely important for various applications. To solve this challenging problem, a novel highly efficient multielement flame retardant (PMSBA) is synthesized and the flame‐retardant and mechanical properties of modified epoxy resins are greatly enhanced without significantly altering their and thermal properties by applying the as‐synthesized PMSBA. The limiting oxygen index value reaches up to 29.6% and could pass the V‐0 rating in the UL‐94 test with even low P content (0.13%). Furthermore, cone calorimetry results demonstrate that 30.3% reduction in the peak heat release rate for the sample with 10.0 wt% PMSBA is achieved. X‐ray photoelectron spectroscopy and scanning electron microscopy indicate that Si‐C, Si‐N, and phosphoric acid derivative can be transformed into a multihole and intumescent char layer as an effective barrier, preserving the epoxy resin structure from fire. More importantly, mechanical properties such as impact strength, tensile strength, and flexural strength are also increased by 63.86%, 33.54%, and 15.65%, respectively, which show the incorporation of PMSBA do not deteriorate the mechanical properties of modified epoxy resins. All the results show that PMSBA is a promising strategy for epoxy resin with satisfactory, thermal, flame‐retardant, and mechanical properties.     

The application of Ce‐doped titania nanotubes in the intumescent flame‐retardant PS/MAPP/PER systems

In this work, we reported the synthesis, characterization of Ce‐doped titania nanotubes (Ce‐TNTs), and application in flame retardancy of an intumescent flame‐retardant polystyrene (PS/IFR) system. The flame retardancy of polystyrene (PS) composite that was composed of pentaerythritol, microencapsulated ammonium polyphosphate, and PS was enhanced significantly by adding a small amount (0.1 wt%) of (Ce‐TNTs). The thermal properties of the flame‐retardant PS were investigated by thermogravimetric analysis, limiting oxygen index (LOI), vertical burning test (UL‐94), scanning electronic microscopy, dynamic mechanical thermal analysis, and the real‐time Fourier transform infrared spectrometry (FTIR). The maximal decomposition rate temperature of PS/IFR containing Ce‐TNTs in air is much higher than that of other PS composite without Ce‐TNTs. The LOI value of PS/IFR that contained 0.1 wt% of Ce‐TNTs was increased from 27.0 to 28.5, and the UL‐94 rating was also enhanced to V‐0 from no rating when the total loading of additive was the same. The real‐time FTIR showed that the degradation process was changed after the addition of TNTs. All results indicated that Ce‐TNTs had a significant synergistic effect on the flame retardancy of PS/IFR. Copyright © 2012 John Wiley & Sons, Ltd.     

Synergistic flame‐retardant effect and mechanisms of boron/phosphorus compounds on epoxy resins

To explore the component synergistic effect of boron/phosphorus compounds in epoxy resin (EP), 3 typical boron compounds, zinc borate (ZB), boron phosphate (BPO₄), and boron oxide (B₂O₃), blended with phosphaphenanthrene compound TAD were incorporated into EP, respectively. All 3 boron/phosphorus compound systems inhibited heat release and increased residue yields and exerted smoke suppression effect. Among 3 boron/phosphorus compound systems, B₂O₃/TAD system brought best flame‐retardant effect to epoxy thermosets in improving the UL94 classification of EP composites and also reducing heat release most efficiently during combustion. B₂O₃ can interact with epoxy matrix and enhance the charring quantity and quality, resulting in obvious condensed‐phase flame‐retardant effect. The combination of condensed‐phase flame‐retardant effect from B₂O₃ and the gaseous‐phase flame‐retardant effect from TAD effectively optimized the action distribution between gaseous and condensed phases. Therefore, B₂O₃/TAD system generated component synergistic flame‐retardant effect in epoxy thermosets.     

Effect of ethyl‐bridged diphenylphosphine oxide on flame retardancy and thermal properties of epoxy resin

Three commercialized flame retardants, 1,2‐bis(diphenylphosphinoyl)ethane (EDPO), 6,6‐(1,2‐phenethyl)bis‐6H‐dibenz[c,e][1,2]oxaphosphorin‐6,6‐dioxide (HTP‐6123), and hexa‐phenoxy‐cyclotriphosphazene (HPCTP), were used to prepare the flame retardant diglycidyl ether of bisphenol A (DGEBA) epoxy resin (EP) under the same experimental conditions. The effects of T_g, thermal stability, and water absorption properties of EP caused by the three flame retardants were investigated and compared, together with their flame retardant efficiency. Results showed that the introduction of the three flame retardants improved the flame retardant performance of EP but led to decreases in T_g and decomposition temperature. EDPO showed higher flame retardant efficiency than the other two flame retardants. EP/EDPO showed higher thermal stability, better flame retardant performance, higher T_g value, and lower water absorption than EP/HTP‐6123 and EP/HPCTP. The study discovered that EDPO and HTP‐6123 primarily act through the gas phase flame retardant mechanism, while HPCTP is primarily driven by the condensed phase mechanism.     

Synthesis of a caged bicyclic phosphates derived anhydride and its performance as a flame‐retardant curing agent for epoxy resins

A novel curing and flame‐retardant agent (PEPA‐TMAC) was successfully synthesized. The chemical structure was characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR). Use of PEPA‐TMAC as part of the curing agent in combination with another anhydride for a commercial epoxy resin (EP) was studied. Results of differential scanning calorimetry (DSC) indicated that PEPA‐TMAC was an effective curing agent for EP. The dynamic mechanical analysis (DMA) results showed that the glass transition temperature (T_g) and cross‐linking density (V_e) of EP composites exhibited an increase trend with the addition of PEPA‐TMAC. The limiting oxygen index (LOI) value of EP composites reached 26.9%, and the cone calorimeter results indicated that peak heat release rate (PHRR), total heat release (THR), smoke produce rate (SPR), and total smoke produce (TSP) remarkably decreased with increasing PEPA‐TMAC content. TGA data showed that the addition of PEPA‐TMAC greatly increased the amount of residual char during combustion. The morphology of the residual char was studied by SEM and showed that the addition of PEPA‐TMAC greatly increased the stability of EP composites. The thermogravimetric analysis (TGA), energy‐dispersive X‐ray spectroscopy (EDS), and FTIR results revealed the flame‐retardant mechanism that PEPA‐TMAC can promote the formation of charred layers with the phospho‐carbonaceous complexes in the condensed phase during burning of EP composites.     

Synthesis of DOPO‐based pyrazine derivative and its effect on flame retardancy and thermal stability of epoxy resin

A novel DOPO‐based pyrazine derivative 6‐((2‐hydroxyphenyl)(pyrazin‐2‐ylamino)methyl)dibenzo[c,e][1,2]oxaphosphinine 6‐oxide (DHBAP) was triumphantly synthesized by a two‐step addition reaction using 2‐aminopyrazine, 2‐hydroxybenzaldehyde and 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) as reactants, and characterized by Fourier‐transform infrared (FTIR), ³¹P nuclear magnetic resonance (NMR) and ¹H NMR. Afterwards, the addition type flame retardant (DHBAP) was utilized to modify epoxy resin (EP) by blending method. When the content of DHBAP in neat EP was 8 wt%, it reached to the V‐0 rating and the limited oxygen index (LOI) value up to 34.0%. Furthermore, according to the cone calorimeter (CC) test results, the heat release rate (HRR), total heat release (THR), smoke produce rate (SPR) and total smoke production (TSP) of EP/8% DHBAP decreased by 26.3%, 21.3%, 37.0% and 60.9% when compared with neat EP, respectively, indicating that DHBAP had good inhibition on heat and smoke releases. Eventually, the flame‐retardant mechanism of DHBAP was further explored by X‐ray photoelectron spectroscopy (XPS), Raman spectroscopy, and pyrolysis‐gas chromatography/mass spectrometry (Py‐GC/MS). The results showed that DHBAP had good flame‐retardant activity in the gasous‐condensed two phases.     

Synthesis of phosphorus-based flame retardant systems and their use in an epoxy resin

Methods are proposed to synthesize efficient organophosphorous compounds and combine them with montmorillonite nanoparticles. The chemical-physical structure and mechanism of action of the new systems were studied in epoxy resin. Best results were achieved using the fully phosphorylated calixresorcinarene derivative: the heat release rate peak could be decreased by 61% and the LOI value was increased from 21 to 28. The salt form of additives in case of phosphorylated phloroglucine derivatives was not advantageous in epoxy resin, because the additives could not participate in the crosslinking process effectively due to their inhomogenous distribution in the matrix. The incorporation of the nanoparticles did not create the desired flame retardant effect which can be explained by the increased heat conductivity and lower mobility of the nanoparticles due to the crosslinked structure.     

Synthesis of a novel DPPA‐containing benzoxazine to flame‐retard epoxy resin with maintained thermal properties

The flame‐retarded epoxy resin with improved thermal properties based on environmentally friendly flame retardants is vital for industrial application. Hereby, a novel reactive‐type halogen‐free flame retardant, 10‐(3‐(4‐hydroxy phenyl)‐3,4‐dihydro‐2H‐benzo[e] [1,3] oxazin‐4‐yl)‐5H‐phenophosphazinine 10‐oxide (DHA‐B) was synthesized via a two‐step reaction route. Its structure was characterized using ¹H, ¹³C, and ³¹P NMR and HRMS spectra. For 4,4′‐diaminodipheny ethane (DDM) and diglycidyl ether of bisphenol A (DGEBA)‐cured systems, the epoxy resin with only 2 wt% loading of DHA‐B passed V‐0 rating of UL‐94 test. Significantly, its glass transition temperature (T_g) and initial decomposition temperature (T_5%) were as high as 169.6°C and 359.6°C, respectively, which were even higher than those of the corresponding original epoxy resin. Besides, DHA‐B decreased the combustion intensity during combustion. The analysis of residues after combustion suggested that DHA‐B played an important role in the condensed phase.     

The effect of a novel phosphorus-nitrogen reactive flame retardant curing agent on the performance of epoxy resin

A phosphorus-nitrogen reactive flame retardant curing agent poly-(isophorondiamine spirocyclic pentaerythritol bisphosphonate) (PIPSPB) was synthesized. The chemical structure of the obtained compound was identified by FTIR, ¹HNMR, and mass spectroscopies. Different proportions of DDS and PIPSPB were compounded as the curing agents to prepare a series of flame retardant epoxy resins with different phosphorus contents. The curing behavior of E-44/PIPSPB?+?DDS system was studied by DSC. A series of tests were conducted to characterize E-44/PIPSPB?+?DDS thermosetting system’s performance. The result demonstrates that the residual carbon content of EP/PIPSPB?+?DDS system is obviously higher than that of EP/DDS system after 500?°C with the increase of phosphorus content in the system, and the heat release rate of the system during combustion is significantly reduced. The generated phosphorus-containing carbon layer is obviously foamed, which shows that the flame retardancy of the system is the result of the combined action of condensed phase and gas phase. When the phosphorus content is 1.77wt%, EP-3 successfully passed UL94 V-0 flammability rating, the LOI value was as high as 29%, the impact strength and tensile strength of it were 6.08KJ/m² and 49.10MPa respectively, the adhesive strength could reach 13.89?MPa, the system presents a good overall performance.     

含季戊四醇磷酸酯阻燃剂的合成与表征

采用1-氧代-4-羟甲基-2,6,7-三氧杂-1-磷杂双环[2.2.2]辛烷(PEPA)、三氯氧磷、双酚A和双酚S为反应物,合成了两个新型添加型阻燃剂:双酚A双[二(1-氧代-1-磷杂-2,6,7-三氧杂双环辛烷-4-亚甲基)]磷酸酯(BAPP)和双酚S双[二(1-氧代-1-磷杂-2,6,7-三氧杂双环辛烷-4-亚甲基)]磷酸酯(BSPP),通过元素分析、FT-IR和1H NMR等表征了标题化合物的结构,结果表明,所合成的标题化合物的结构与预期一致。热失重分析结果证明,BAPP和BSPP质量损失5%(wt)时的温度分别为343.6℃和352.3℃,600℃残余量分别达46.6%和55.5%,具有较高的热稳定性和结炭性能。阻燃性能实验证明,E-51环氧树脂中分别添加质量分数为18.2%(wt)的BAPP和BSPP时,极限氧指数分别为32.2%和31.8%,均能达到UL 94 V-0级。     

Flame retardant and toughening behaviors of bio‐based DOPO‐containing curing agent in epoxy thermoset

Based on bio‐based furfural, a phosphorus‐containing curing agent (FPD) was successfully synthesized, via the addition reaction between 9,10‐dihydro‐9‐oxa‐10 phosphaphenanthrene‐10‐oxide (DOPO) and furfural‐derived Schiff base. Then, as co‐curing agent, FPD was used to prepare flame retardant epoxy thermosets (EP) cured by 4, 4′‐diaminodiphenyl methane. The incorporated FPD improved the flame retardancy and toughness of epoxy thermoset, simultaneously. When 5 wt% FPD was added into EP, the FPD/EP achieved 35.7% limited oxygen index (LOI) value and passed UL94 V‐0 rating, meanwhile. In FPD/EP thermoset, the incorporated FPD reduced the thermal decomposition rate, increased the charring capacity, and inhibited the combustion intensity of epoxy thermoset. Through gas‐phase and condensed‐phase actions in weakening fuel supply, suppressing volatile combustion, and enhancing charring barrier effect, FPD decreased the heat release of burning epoxy thermoset, significantly. For the outstanding effectiveness on both flame retardancy and toughness, the study on FPD provides a promising way to manufacture high‐performance epoxy thermoset.     

A novel halogen‐free co‐curing agent with linear multi‐aromatic rigid structure as flame‐retardant modifier in epoxy resin

A novel halogen‐free 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO)‐containing co‐curing agent, 6,6′‐(1,4‐phenylenebis(((4‐(phenylamino)phenyl)amino)methylene))bis(dibenzo[c,e][1,2]oxaphosphinine 6‐oxide) (DPN) was synthesized via a simple 1‐pot or 2‐step procedure with yield of 86.2% and 70.8%, respectively. The molecular structures of 4,4′‐((1,4‐phenylenebis(methanylylidene))bis(azanylylidene))bis(N‐phenylaniline) (DPN intermediate) and DPN are characterized by FTIR, NMR, and MS. TGA tests show that the char yield of DPN/EP composites raises to 30.9% when the molar ratio of DPN to 4,4‐diaminodiphenyl methane(DDM) is 20:80. T_g values of DPN/EP composites tested by DSC and DMA are similar to neat epoxy resin (EP), which is due to the secondary amine in DPN that participates in the cross‐linking reaction of epoxy resin. The storage modulus in the rubber stage (E′‐190 °C) of flame‐retardant epoxy resin is close to that of neat EP, while their tanδ's are lower, which indicates the similarity of samples' cross‐linking density due to the participation of DPN in the cross‐linking reaction. The results show that when the molar ratio of DPN and DDM is 5:95, the epoxy has a higher T_g value and better mechanical properties than other samples. The introduction of DPN efficiently improves the flame‐retardant properties of epoxy resin with V‐0 rating of UL‐94 vertical burning test, non‐dripping, 41% of limit oxygen index (LOI) value, low peak heat release rate (PHRR), and total heat release (THR).     

Flame‐retardant epoxy resin compounds containing novolac derivatives with aromatic compounds

New flame‐retardant epoxy resin compounds containing novolac derivatives with specific aromatic compounds have been developed. After crosslinking reactions between epoxy resin and hardener, the epoxy resin compounds formed highly flame‐retardant network structures that were obtained by including biphenylene and phenylene moieties in the main chains of novolac‐type epoxy resin and phenol novolac resin hardener. The high flame retardancy is due mainly to the stable foam layers that form during combustion because of the low elasticity at high temperatures and the high pyrolysis resistance of the compounds. Furthermore, the addition of excess phenol derivative hardener not only facilitates the formation of the foam layers by decreasing the crosslink densities but also reduces the amount of flammable substances generated from the epoxy resin compounds during combustion. The use of a multifunctional epoxy resin containing four glycidyloxy groups in the compounds improved characteristics such as heat resistance and strength at high temperatures, while maintaining excellent flame retardancy. Copyright © 2001 John Wiley & Sons, Ltd.     

Synthesis of a novel phosphorus‐containing curing agent and its effects on the flame retardancy,thermal degradation and moisture resistance of epoxy resins

A novel phosphorus‐containing compound diphenyl‐(1, 2‐dicarboxylethyl)‐phosphine oxide defined as DPDCEPO was synthesized and used as a flame retardant curing agent for epoxy resins (EP). The chemical structure of the prepared DPDCEPO was well characterized by Fourier transform infrared spectroscopy, and ¹H, ¹³C and ³¹P nuclear magnetic resonance. The DPDCEPO was mixed with curing agent of phthalic anhydride (PA) with various weight ratios into epoxy resins to prepare flame retardant EP thermosets. The flame retardant properties, combustion behavior and thermal analysis of the EP thermosets were respectively investigated by limiting oxygen index (LOI), vertical burning tests (UL‐94), cone calorimeter measurement, dynamic mechanical thermal analysis and thermogravimetric analysis (TGA) tests. The surface morphologies and chemical compositions of the char residues for EP thermosets were respectively investigated by scanning electron microscopy and X‐ray photoelectron spectroscopy (XPS). The water resistant properties of the cured EP were evaluated by putting the samples into distilled water at 70°C for 168 hr. The results revealed that the EP/20 wt% DPDCEPO/80 wt% PA thermosets successfully passed UL‐94 V‐0 flammability rating and the LOI value was as high as 33.2%. The cone test results revealed that the incorporation of DPDCEPO effectively reduced the combustion parameters of the epoxy resin thermosets, such as heat release rate and total heat release. The dynamic mechanical thermal analysis test demonstrated that the glass transition temperature (Tg) decreased with the increase of DPDCEPO content. The TGA results indicated that the incorporation of DPDCEPO promoted the decomposition of epoxy resin matrix ahead of time and led to a higher char yield and thermal stability at high temperatures. The surface morphological structures and analysis of the XPS of the char residues of EP thermosets revealed that the introduction of DPDCEPO benefited the formation of a sufficient, compact and homogeneous char layer with rich flame retardant elements on the epoxy resin material surface during combustion. The mechanical properties and water resistance of the cured epoxy resins were also measured. After water resistance tests, the EP/20 wt% DPDCEPO/80 wt% PA thermosets retained excellent flame retardancy, and the moisture adsorption of the EP thermosets decreased with the increase of DPDCEPO content in EP thermosets because of the existence of the P–C bonds and the rigid aromatic hydrophobic structure in DPDCEPO. Copyright © 2015 John Wiley & Sons, Ltd.