Synthesis and characterization of hyperbranched polyfluorenes containing triarylpyrazoline cores towards efficient blue light‐emitting diodes

New series of hyperbranched polyfluorenes containing triarylpyrazoline cores, PFZ10 , PFZ20 , PFNZ10 , and PFNZ20 , have been synthesized according to the “A₂ + A′₂ + B₃” Suzuki coupling method. The structures and property of the monomers and conjugated polymers were characterized by elemental analysis, gel permeation chromatography, cyclic voltammetry, thermogravimetric analysis, differential scanning calorimetry, and UV–visible absorption, ¹H NMR, ¹³C NMR, and photoluminescence spectroscopies. All these polymers exhibited good solubility in common organic solvents and good thermal stability. The long‐wavelength emission of polyfluorenes had been effectively reduced in these hyperbranched polymers. Standard polymer light emitting devices (PLEDs) from PFZ10 , PFZ20 , PFNZ10 , and PFNZ20 , with the configuration of ITO/PEDOT/polymer/TPBI/Alq₃/Mg:Ag, exhibited good electroluminescence (EL) properties The PLED based on PFNZ10 emitted pure blue light with a low turn‐on voltage of 5.3 V and a high EL efficiency of about 1.93%. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5296–5307, 2007     

Stable and good color purity white light‐emitting devices based on random fluorene/spirofluorene copolymers doped with iridium complex

Conjugated polymers PSNFP and PSNFF based on naphthalene‐containing spirofluorene structure and 9,9‐dioctylfluorene, 2,5‐dioctylbezene were designed and synthesized for light emitting applications. These two polymers show good blue emission both in solution and thin film. Thermal gravimetric analysis reveals they have good thermal stability with the decomposition temperature higher than 400 °C. Electrochemistry characterization shows that both of these polymers have a large band gap and deep highest occupied molecular orbital, which are important features for phosphorescent host materials. White light‐emitting diodes were fabricated by using PSNFF as the host material, containing two typical phosphorescent Ir complex dopants: green emitter Ir(mppy)₃ and red emitter Ir(piq)₂. The color coordinate CIE stayed nearly constant, changed from (0.32, 0.31) to (0.28, 0.31) when the current density varied from 2 to 20 mA cm^?2. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Conjugated and partially conjugated 2,5‐diphenylthiophene‐containing light‐emitting copolymers in polymeric light‐emitting diode (PLED) device fabrications

To study the effect of nonconjugation on polymeric and photophysical properties of thiophene‐containing polymers, new light‐emitting copolymers comprising either alternate 2,5‐diphenylthiophene and vinylene or alternate 2,5‐diphenylthiophene and aliphatic ether segments were synthesized. Both copolymers contained 2,5‐diphenylthiophene as the major chromophore and emitted a sky bluish fluorescence in dilute solution (10^?2 mg/mL). With a rigid and planarity structure and the concomitant crystallinity, the former copolymer (fully conjugated) possessed a higher quantum efficiency, a higher glass‐transition temperature, and a better thermal stability. In contrast, the latter copolymer (conjugated–nonconjugated) had better solubility and provided enhanced photophysical properties for the fabricated polymeric light‐emitting diode (PLED) device: at 15 V, the maximum current and brightness were 110 mA/cm² and 4289 cd/m², respectively, and the electroluminescence efficiency remained constant at approximately 4.9 cd/A in a voltage range of 8 to 14 V. The existence of intramolecular/intermolecular aggregates in the latter copolymer was corroborated from the the UV–vis and photoluminescence spectra of its solutions. With an increase in solution concentration, the shape and λ_max of the photoluminescence spectrum were redshifted. In a solution with a concentration as high as 10 mg/mL, the redshift was so drastic that the photoluminescence spectrum was nearly identical to that of a solid‐film. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6061–6070, 2004     

Deep‐blue light‐emitting polyfluorenes containing spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers

Blue light‐emitting polyfluorenes, PPF‐FSOs and PPF‐SOFs were synthesized via introducing spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers (2,7‐diyl and 2′,7′‐diyl) (FSO/SOF) into the poly[9,9‐bis(4‐(2‐ethylhexyloxy) phenyl)fluorene‐2,7‐diyl] (PPF) backbone, respectively. With the increasing contents of FSO and SOF moieties, the absorption and PL spectra of PPF‐FSOs show slight red shift, while that of PPF‐SOFs exhibit blue shift, respectively. The HOMO and LUMO levels reduce gradually with increasing SOF unit in PPF‐SOFs. The polymers emit blue light peaked around 430–445 nm and show an excellent spectral stability with the variation in current densities. The distinctly narrowing EL spectra were observed with the incorporation of isomers in the polymers. The full width at half maximum reduced by 15 nm for PPF‐SOFs, resulting in a blue shift with the CIE coordinates from (0.16, 0.11) to (0.16, 0.08). With a device configuration of ITO/PEDOT:PSS/EML/CsF/Al, a maximum luminance efficiency (LE_max) of 2.00 cd A^?1, a maximum external quantum efficiency (EQE_max) of 3.76% with the CIE coordinates of (0.16, 0.08) for PPF‐SOF15 and a LE_max of 1.68 cd A^?1, a EQE_max of 2.38% with CIE (0.16, 0.12) for PPF‐FSO10 were obtained, respectively. The result reveals that spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers are promising blocks for deep‐blue light‐emitting polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2332–2341     

Synthesis and electro‐optical properties of light‐emitting polymers containing oxadiazole derivatives for light‐emitting diodes applications

Two PPV‐based bipolar polymers containing 1,3,4‐oxadiazole pendant groups were synthesized via the Gilch polymerization reaction for use in light‐emitting diodes (LEDs). The resulting polymers were characterized using ¹H and ¹³C NMR, elemental analysis, DSC, and TGA. These polymers were found to be soluble in common organic solvents and are easily spin‐coated onto glass substrates, producing high optical quality thin films without defects. The electro‐optical properties of ITO/PEDOT/polymer/Al devices based on these polymers were investigated using UV‐visible, PL, and EL spectroscopy. The turn‐on voltages of the OC₁Oxa‐PPV and OC₁₀Oxa‐PPV devices were found to be 8.0 V. The maximum brightness and luminescence efficiency of the OC₁Oxa‐PPV device were found to be 544 cd/m² at 19 V and 0.15 cd/A, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1098–1110, 2008     

Synthesis and characterization of white‐light‐emitting polyfluorenes containing orange phosphorescent moieties in the side chain

Two orange phosphorescent iridium complex monomers, 9‐hexyl‐9‐(iridium (III)bis(2‐(4′‐fluorophenyl)‐4‐phenylquinoline‐N,C^2′)(tetradecanedionate‐11,13))‐2,7‐dibromofluorene (Br‐PIr) and 9‐hexyl‐9‐(iridium(III)bis(2‐(4′‐fluorophenyl)‐4‐methylquinoline‐N,C^2′)(tetradecanedionate‐11,13))‐2,7‐dibromofluorene (Br‐MIr), were successfully synthesized. The Suzuki polycondensation of 2,7‐bis(trimethylene boronate)‐9,9‐dioctylfluorene with 2,7‐dibromo‐9,9‐dioctylfluorene and Br‐PIr or Br‐MIr afforded two series of copolymers, PIrPFs and MIrPFs, in good yields, in which the concentrations of the phosphorescent moieties were kept small (0.5–3 mol % feed ratio) to realize incomplete energy transfer. The photoluminescence (PL) of the copolymers showed blue‐ and orange‐emission peaks. A white‐light‐emitting diode with a configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/PIr05PF (0.5 mol % feed ratio of Br‐PIr)/Ca/Al exhibited a luminous efficiency of 4.49 cd/A and a power efficiency of 2.35 lm/W at 6.0 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.46, 0.33). The CIE coordinates were improved to (0.34, 0.33) when copolymer MIr10PF (1.0 mol % feed ratio of Br‐MIr) was employed as the white‐emissive layer. The strong orange emission in the electroluminescence spectra in comparison with PL for these kinds of polymers was attributed to the additional contribution of charge trapping in the phosphorescent dopants. © 2007 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 45: 1746–1757, 2007     

Fluoro‐protected carbazole main‐chain polymers as a new class of stable blue emitting polymers

The protection of the 3,6‐positions of 9‐alkyl‐9H‐carbazole repeat units with fluorine substituents in 2,7‐linked main‐chain polymers as well as in copolymers with triaryl amine repeat units affords blue emitting materials with enhanced electrolytic stability. The electronic conjugation of this new class of materials is more extended than that of the equivalent polymers where the 3,6‐positions are protected with methyl substitutions as a result of the smaller steric hindrance of their fluorine substituents. Attachment of fluorine‐protecting groups at the 3,6‐positions of carbazole repeat units in the homopolymers resulted in materials with relatively high ionization potentials (5.71 eV). However, introduction of triaryl amine comonomers as alternating repeat units provided carbazole/triaryl amine copolymers with a low ionization potential (5.25 eV), a very high quantum yield of fluorescence in solution (0.96), and narrow emission bands [full width at half maximum (FWHM) = 52 nm]. The preparation of this new class of materials together with a study of their electronic and photophysical properties is presented. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis and characterization of highly stable blue‐light‐emitting hyperbranched conjugated polymers

Polyfluorene homopolymer ( P1 ) and its carbazole derivatives ( P2 – P4 ) have been prepared with good yield by Suzuki coupling polymerization. P2 is an alternating copolymer based on fluorene and carbazole; P3 is a hyperbranched polymer with carbazole derivative as the core and polyfluorene as the long arms; P4 is a hyperbranched polymer with carbazole derivative as the core and the alternating fluorene and carbazole as the long arms. These polymers show highly thermal stability, and their structures and physical properties are studied using gel permeation chromatography, ¹H NMR, ¹³C NMR, elemental analysis, Fourier transform infrared spectroscopy, thermogravimetry, UV–vis absorption, photoluminescence, and cyclic voltammetry (CV). The influence of the incorporation of carbazole and the hyperbranched structures on the thermal, electrochemical, and electroluminescent properties has been investigated. Both carbazole addition and the hyperbranched structure increase the thermal and photoluminescent stability. The CV shows an increase of the HOMO energy levels for the derivatives, compared with polyfluorene homopolymer ( P1 ). The EL devices fabricated by these polymers exhibit pure blue‐light‐emitting with negligible low‐energy emission bands, indicating that the hyperbranched structure has a strong effect on the PLED characteristics. The results imply that incorporating carbazole into polyfluorene to form a hyperbranched structure is an efficient way to obtain highly stable blue‐light‐emitting conjugated polymers, and it is possible to adjust the property of light‐emitting polymers by the amount of carbazole derivative incorporated into the polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 790–802, 2008     

High‐efficiency blue light‐emitting polymers based on 3,6‐silafluorene and 2,7‐silafluorene

A novel blue‐emitting polymer based on 3,6‐silafluorene and 2,7‐silafluorene was synthesized via the Suzuki polycondensation. The resulting polymers are readily soluble in common organic solvents, such as toluene, xylene, THF, and chloroform. The thermal, electrochemical, photophysical, and electroluminescence properties of the resulting polymers were investigated. The device fabricated from the copolymer with a configuration of ITO/PEDOT:PSS/PVK/polymer/Ba/Al exhibited an external quantum efficiency of 1.95%, a luminous efficiency of 1.69 cd A^?1 and a maximal brightness of 6000 cd m^?2. It has been found that the incorporation of the 3,6‐silafluorene unit into the poly(2,7‐silafluorene) main chain can not only improve the color purity of the devices from the resulting copolymer but also enhance its device efficiency. Moreover, no undesired long‐wavelength green emission was observed in the PL spectra of P36‐27SiF90 compared to that of PFO with a dominating emission at 500–600 nm after thermal annealing at 200 °C for 8 h. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4941–4949, 2007     

Organic light‐emitting diodes with multiple photocrosslinkable hole‐transport layers

We report on photocrosslinkable hole‐transport polymers and their use as photodefinable hole‐transport layers in organic light‐emitting diodes. The polymers were obtained by copolymerization of bis(diarylamino)biphenyl‐based acrylate monomers with cinnamate‐functionalized acrylate moieties. Polymers with a range of redox potentials were obtained by varying the substitution patterns of the bis(diarylamino)biphenyl units. The 2 + 2 cycloaddition of the cinnamate moieties following UV irradiation renders the material insoluble. This allows for patterning of the polymer and simultaneously enables the fabrication of multilayer structures from solution. Hole mobilities were measured in these copolymers with the time‐of‐flight technique. Their performance as hole‐transport layers in light‐emitting diodes, with tris(8‐hydroxyquinolinato)aluminum as the emitter and electron‐transport layer, is evaluated. Electroluminescent devices with multiple hole‐transport layers having different ionization potentials were fabricated from solution, and the quantum efficiency of these devices was greater than that for devices based on a single hole‐transport layer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2726–2732, 2003     

High‐efficiency doped polymeric organic light‐emitting diodes

Fabrication of polymer light‐emitting diodes based on emission from the phosphorescent molecule fac‐tris(2‐phenylpyridine) iridium doped into a poly(N‐vinyl carbazole) host are reported. For single‐layered devices with magnesium‐silver cathodes, the luminance efficiency at 20 mA/cm² was measured as 8.7 cd/A. This efficiency could be increased by over a factor of two by incorporation of evaporated small‐molecule layers into the device structure. Significant increases in device efficiency were also obtained without these evaporated layers by modification of the electrodes. Incorporation of 3,4‐poly(ethylene dioxythiophene):poly(styrene sulfonate) at the anode improved the device efficiency but had little impact on drive voltage. Insertion of lithium fluoride at the cathode resulted in no improvement in performance for magnesium‐silver and aluminum cathodes, but a significant improvement was realized in efficiency and drive voltage for calcium‐aluminum cathodes. Excellent device performance was observed for all three cathode metals used in conjunction with cesium fluoride. Through optimization of the electrodes and emitter‐layer thickness, devices exhibiting efficiencies as high as 37.3 cd/A are realized. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2715–2725, 2003     

New series of highly phenyl‐substituted polyfluorene derivatives for polymer light‐emitting diodes

A new series of highly phenyl‐substituted polyfluorene derivatives were synthesized and characterized. The resulting polymers were amorphous and showed excellent solubility in common organic solvents, such as chloroform, tetrahydrofuran, xylene, toluene, chlorobenzene, and so forth. All possessed satisfied thermal stability with glass‐transition temperatures (T_g's) in the range of 79–115 °C. They emitted blue light with photoluminescent (PL) maximum peaks at about 408–412 nm in thin films. The PL efficiencies of the polymer films were measured around 30–33%. The highly phenylated pendants improved the T_g of polyfluorene without forming defects in the polymers and reduced their tendency to form aggregate/excimers. Polymer light‐emitting diodes were fabricated from these polymers with the configuration of indium tin oxide/polyethylenedioxythiophene:polystyrene sulfonic acid/polymer/Ba/Al, which emitted bright blue light with maximum peaks at 418–420 nm. The maximum external quantum efficiencies of these devices were 0.41–0.6%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2985–2993, 2004     

Synthesis of fluorene‐based hyperbranched polymers for solution‐processable blue,green, red,and white light‐emitting devices

For the purpose of making hyperbranched polymer (Hb‐Ps)‐based red, green, blue, and white polymer light‐emitting diodes (PLEDs), three Hb‐Ps Hb‐ terfluorene ( Hb‐TF ), Hb ‐4,7‐bis(9,9′‐dioctylfluoren‐2‐yl)‐2,1,3‐benzothiodiazole ( Hb‐BFBT ), and Hb‐ 4,7‐bis[(9,9′‐dioctylfluoren‐2‐yl)‐thien‐2‐yl]‐2,1,3‐benzothiodiazole ( Hb‐BFTBT ) were synthesized via [2+2+2] polycyclotrimerization of the corresponding diacetylene‐functionalized monomers. All the synthesized polymers showed excellent thermal stability with degradation temperature higher than 355 °C and glass transition temperatures higher than 50 °C. Photoluminance (PL) and electroluminance (EL) spectra of the polymers indicate that Hb‐TF , Hb‐BFBT , and Hb‐BFTBT are blue‐green, green, and red emitting materials. Maximum brightness of the double‐layer devices of Hb‐TF , Hb‐BFBT , and Hb‐BFTBT with the device configuration of indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/light‐emitting polymer/CsF/Al are 48, 42, and 29 cd/m²; the maximum luminance efficiency of the devices are 0.01, 0.02, and 0.01 cd/A. By using host–guest doped system, saturated red electrophosphorescent devices with a maximum luminance efficiency of 1.61 cd/A were obtained when Hb‐TF was used as a host material doped with Os(fptz)₂(PPh₂Me₂)₂ as a guest material. A maximum luminance efficiency of 3.39 cd/A of a red polymer light‐emitting device was also reached when Hb‐BFTBT was used as the guest in the PFO (Poly(9,9‐dioctylfluorene)) host layer. In addition, a series of efficient white devices were, which show low turn‐on voltage (3.5 V) with highest luminance efficiency of 4.98 cd/A, maximum brightness of 1185 cd/m², and the Commission Internationale de l'Eclairage (CIE) coordinates close to ideal white emission (0.33, 0.33), were prepared by using BFBT as auxiliary dopant. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Pyrene‐functionalized oligofluorenes as non‐doped deep blue emitters for solution‐processed organic light‐emitting diodes

Two pyrene‐functionalized oligofluorenes (TPA‐PyF₃ and CBP‐PyF₃) are prepared using the condensation reaction by the Friedel–Crafts procedure. In the produced oligomers, the triphenylamine or N,N′‐dicarbazolyl‐4,4′‐biphenyl core serves as a spacer bearing spiro‐linked fluorene moieties to form a multi‐H shaped structure. This specific structure efficiently retards the crystallization tendency of the pyrene groups, and gives the materials completely amorphous morphological structure and film forming ability. Solution‐processed OLEDs with the structure of ITO/PEDOT:PSS (25 nm)/TPA‐PyF₃ or CBP‐PyF₃ (40 nm)/TPBI (35 nm)/Ca (10 nm)/Ag (100 nm) show low turn‐on voltages of 3.6 V, and the maximum external quantum efficiencies reach 1.78% and 2.07% for TPA‐PyF₃ and CBP‐PyF_3, respectively. Moreover, both devices exhibit stable deep‐blue light emission with Commission International de I'Eclairage (CIE) coordinates of around (0.16, 0.09) at the brightness of 100–1000 cd m^?2. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 795–801     

Thermally crosslinkable hole‐transporting poly(fluorene‐co‐triphenylamine) for multilayer polymer light‐emitting diodes

This article reports the synthesis and characterization of a novel thermally crosslinkable hole‐transporting poly (fluorene‐co‐triphenylamine) (PFO‐TPA) by Suzuki coupling reaction, followed with its application in the fabrication of multilayer light‐emitting diodes by wet processes. The thermal, photophysical, and electrochemical properties of PFO‐TPA were investigated by differential scanning calorimeter, thermogravimetric analysis, optical spectroscopy, and cyclic voltammetry, respectively. Thermally crosslinked PFO‐TPA, through pendant styryl groups, demonstrates excellent thermal stability (T_d > 400 °C, T_g = 152 °C), solvent resistance, and film homogeneity. Its highest occupied molecular orbital level (?5.30 eV) lies between those of PEDOT:PSS (?5.0 ～ ?5.2 eV) and poly(9,9‐dioctylfluorene) (PFO: ?5.70 eV), forming a stepwise energy ladder to facilitate hole injection. Multilayer device with crosslinked PFO‐TPA as hole‐injection layer (HIL) (ITO/PEDOT:PSS/HIL/PFO/LiF/Ca/Al) was readily fabricated by successive spin‐coating processes, its maximum luminance efficiency (3.16 cd/A) were about six times higher than those without PFO‐TPA layer (0.50 cd/A). The result of hole‐only device also confirmed hole‐injection and hole‐transport abilities of crosslinked PFO‐TPA layer. Consequently, the device performance enhancement is attributed to more balanced charges injection in the presence of crosslinked PFO‐TPA layer. The thermally crosslinkable PFO‐TPA is a promising material for the fabrication of efficient multilayer polymer light‐emitting diodes because it is not only a hole‐transporting polymer but also thermally crosslinkable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Pure white‐light‐emitting diodes from phosphorescent single polymer systems

New white polymeric light‐emitting diodes from phosphorescent single polymer systems have been developed using a blue‐light‐emitting fluorene monomer copolymerized with a red‐light‐emitting phosphorescent dye, and end‐capped with a green‐light‐emission dye. All of the copolymers have good thermal stability with 5% weight loss temperatures at 380–413 °C and glass transition temperatures at 75–137 °C. We obtained white‐light‐emission devices by adjusting the molar ratio of the comonomers with a structure of indium tin oxide/poly(3,4‐ethylenedioxythiophene): poly(styrene sulfonic acid)/polyvinylcarbazole (PVK)/emission layer/Ca/Ag. The highest brightness in such a device configuration is 300 cd/m² at a current density of 2900 A/m² with high white color quality (Commission Internationale de l'Eclairage (CIE) coordinates of (0.33, 0.34)). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 464–472, 2008     

Synthesis and characterization of new light‐emitting copolymers in polymeric‐light‐emitting‐diode device fabrications

A series of thiophene‐containing photoactive copolymers consisting of alternating conjugated and nonconjugated segments were synthesized. The ¹H NMR spectra corroborated the well‐defined structures, and the copolymers not only were soluble in common organic solvents but also had high glass‐transition temperatures (ca. 130 °C) and good thermal stability up to 390 °C. Introducing aliphatic functional groups, such as alkyl or alkoxyl, into chromophores of the copolymers redshifted the photoluminescence spectra and lowered the optical bandgaps. The electrochemical bandgaps calculated from cyclic voltammetry agreed with the optical bandgaps and thus indicated that electroluminescence and photoluminescence originated from the same excited state. The energy levels (highest occupied molecular orbital and lowest unoccupied molecular orbital) of all the copolymers were lower than those of poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1.4‐phenylenevinylene] MEH–PPV, indicating balanced hole and electron injection, which led to improved performance in both single‐layer and double‐layer polymeric‐light‐emitting‐diode devices fabricated with these copolymers. All the copolymers emitted bluish‐green or green light above the threshold bias of 5.0 V under ambient conditions. At the maximum bias of 10 V, the electroluminescence of a device made of poly(2‐{4‐[2‐(3‐ethoxy phenyl)ethylene]phenyl}‐5‐{4‐[2‐(3‐ethoxy,4‐1,8‐octanedioxy phenyl)ethylene]phenyl}thiophene) was 5836 cd/m². The external electroluminescence efficiency decreased with the lifetime as the polymer degraded. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3954–3966, 2004     

Soluble polynorbornenes with pendant carbazole derivatives as host materials for highly efficient blue phosphorescent organic light‐emitting diodes

We report novel host polymers for a high‐efficiency polymer‐based solution‐processed phosphorescent organic light‐emitting diode with typical blue‐emitting dopant bis(4,6‐difluorophenylpyridinato‐N,C²)iridium(III) picolinate (FIrpic). The host polymers, soluble polynorbornenes with pendant carbazole derivatives, N‐phenyl‐9H‐carbazole ( P1 ), N‐biphenyl‐9H‐carbazole ( P2 ), and 9,9′‐(1,3‐phenylene)bis‐9H‐carbazole (mCP) ( P3 ) are efficiently synthesized by vinyl addition polymerization of norbornene monomers using Pd(II) catalyst in combination with 1‐octene chain transfer agent. The polymers exhibit high thermal stability with high decomposition (T_d5 > 410 °C) and glass transition temperatures (T_g ≈ 268 °C). The HOMO (ca. ?5.5 to ?5.7 eV) and LUMO (ca. ?2.0 to ?2.1 eV) levels with the high triplet energy of about 2.7–3.0 eV suggest that the polymers are suitable for a host material for blue emitters. Among the solution‐processed devices that were fabricated based on the emissive layers containing the P1 ? P3 host doped with various concentrations of FIrpic (7–13 wt %), the best device with P3 host exhibits power efficiency of 3.0 lm W^?1 and external quantum efficiency of 4.0% at a luminance of 1000 cd m^?2 that is outstanding among the polymeric rivals. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Encapsulants for light‐emitting diodes from visible light‐cured epoxy monomers

During the last decade, light‐emitting diodes (LEDs) have replaced incandescent, fluorescent, and neon lamps due to their ability to produce high luminosity at low currents and voltages. LEDs are currently encapsulated by thermally curable epoxy resins. However, long periods of curing at high temperature result in high consumption of energy and require stringent process control to avoid failure of the devices. In addition, the thermal cure results in yellowing of the encapsulant, which decreases the efficiency of the LED. In recent years, photoinitiated polymerization has received much interest as it congregates a wide range of economic and ecological benefits. Cationic photoinitiators, such as diaryliodonium salts, generate Brønsted acid in situ, which initiates polymerization. The process can be triggered on demand by irradiating the mixture with light. Results from the present research reveal that cycloaliphatic epoxy monomers, photoactivated with an iodonium salt and Camphorquinone, polymerize readily under visible light irradiation (470 nm) in the absence of external heating. The partial replacement of cycloaliphatic epoxy with aromatic diglycidyl ether of bisphenol‐A (DGEBA) is an effective means of improving the refractive index of the material and consequently the efficiency of the photoemission. Visible light polymerization of DGEBA pure proceeds at a slow rate; however, it is enhanced by the increase in temperature during the polymerization of the highly reactive cycloaliphatic monomer. From results obtained in the present research, it may be concluded that visible light polymerization of epoxy monomers is a promising route for the processing of LED encapsulants. Copyright © 2013 John Wiley & Sons, Ltd.