Phosphorus‐containing polyamide Mg(OH)2 nanocomposite coating on surface of poly(vinyl chloride) thin film: Study on thermal stability,flammability, and mechanical properties

Surface of poly(vinyl chloride) (PVC) thin films was coated using DOPO‐based polyamide (DBPA) coating and DBPA/Mg(OH)₂ nanocomposites (DBPN) coating by dip‐coating process. For this purpose, a new DOPO‐based dicarboxylic acid (DBDA) was synthesized and used for preparation of DBPA and organically surface modification of Mg(OH)₂ nanoparticles. The effects of DBPA and DBPN coatings on the morphology, thermal stability, combustion, and mechanical properties of PVC were investigated. The uniform dispersion of Mg(OH)₂ nanoparticles (nano‐MDH) and organically coating manner on the surface of the PVC films were confirmed by ATR‐IR spectroscopy, X‐ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), energy dispersive X‐ray, and elemental mapping. From thermal gravimetry analysis (TGA) results, the 10 mass% loss temperature (T₁₀) increased from 268°C to 272°C in PVC coated with DBPA‐containing 10 mass% of modified Mg(OH)₂ (MMH). Also the char residue, first and second mass loss temperatures of all PVC coated were increased compared with the neat PVC film. According to microscale combustion calorimetry (MCC) results, the peak of heat release rate (pHHR) and total heat release (THR) were decreased from 128 ± 2 to 69 W/g and 12 ± 1 to 4 ± 2 KJ/g for PVC film coated with DBPA‐containing 10 mass% of MMH, compared with the neat PVC. From tensile test results, tensile strength was increased from 31.78 ± 0.8 to 39.64 ± 0.9 MPa for PVC coated with polyamide‐containing 5 mass% of MMH compared with the neat PVC.     

Surface‐modified hydroxyapatite linked by L‐lactic acid oligomer in the absence of catalyst

A new surface modification method of hydroxyapatite nanoparticles (n‐HA) by surface grafting reaction of L ‐lactic acid oligomer with carboxyl terminal (LAc oligomer) in the absence of any catalyst was developed. The LAc oligomer with a certain molecular weight was directly synthesized by condensation of L ‐lactic acid. Surface‐modified HA nanoparticles (p‐HA) were attested by Fourier transformation infrared spectroscopy, ³¹P MAS‐NMR, and thermal gravimetric analysis (TGA). The results showed that LAc oligomer could be grafted onto the n‐HA surface by forming a Ca carboxylate bond. The grafting amount of LAc oligomer was about 13.3 wt %. The p‐HA/PLLA composites showed good mechanical properties and uniform microstructure. The tensile strength and modulus of the p‐HA/PLLA composite containing 15 wt % of p‐HA were 68.7 MPa and 2.1 GPa, respectively, while those of the n‐HA/PLLA composites were 43 MPa and 1.6 GPa, respectively. The p‐HA/PLLA composites had better thermal stability than n‐HA/PLLA composites and neat PLLA had, as determined by isothermal TGA. The hydrolytic degradation behavior of the composites in phosphate buffered saline (PBS, pH 7.4) was investigated. The p‐HA/PLLA composites lost their mechanical properties more slowly than did n‐HA/PLLA composites in PBS because of their reinforced adhesion between the HA filler and PLLA matrix. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5177–5185, 2005     

PLA Electrospun Fibers Reinforced with Organic and Inorganic Nanoparticles: A Comparative Study

In this work, different poly (lactic acid) (PLA)-based nanocomposite electrospun fibers, reinforced with both organic and inorganic nanoparticles, were obtained. As organic fibers, cellulose nanocrystals, CNC, both neat and functionalized by “grafting from” reaction, chitosan and graphene were used; meanwhile, hydroxyapatite and silver nanoparticles were used as inorganic fibers. All of the nanoparticles were added at 1 wt% with respect to the PLA matrix in order to be able to compare their effect. The main aim of this work was to study the morphological, thermal and mechanical properties of the different systems, looking for differences between the effects of the addition of organic or inorganic nanoparticles. No differences were found in either the glass transition temperature or the melting temperature between the different electrospun systems. However, systems reinforced with both neat and functionalized CNC exhibited an enhanced degree of crystallinity of the electrospun fibers, by up to 12.3%. From a mechanical point of view, both organic and inorganic nanoparticles exhibited a decreased elastic modulus and tensile strength in comparison to neat electrospun PLA fibers, improving their elongation at break. Furthermore, all of the organic and inorganic reinforced systems disintegrated under composting conditions after 35 days.     

Influence of imide functionalized organo‐modified Mg‐Al layered double hydroxide on the thermal and mechanical properties of new aliphatic‐aromatic poly (amide‐imide)

A new dicarboxylic acid modified Mg‐Al LDH (DLDH) containing imide groups was prepared and its effects on the thermal and mechanical properties of the new synthesized aliphatic‐aromatic poly (amide‐imide) (PAI) were investigated via preparation of PAI/nanocomposite films by solution casting method. The results of X‐ray diffraction (XRD), field emission‐scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM) showed a uniform dispersion for LDH layers into the PAI matrix. For comparison, the effects of polyacrylic acid‐co‐poly‐2‐acrylamido‐ 2‐methylpropanesulfonic acid (PAMPS‐co‐PAA) modified Mg‐Al LDH (ALDH) on the PAI properties were also studied. The thermogravimetric analysis (TGA) results exhibited that the temperature at 5 mass% loss (T₅) increased from 277 °C to 310 °C for nanocomposite containing 2 mass% of DLDH, while T₅ for nanocomposite containing 2 mass% of ALDH increased to 320 °C, along with the more enhancement of char residue compared to the neat PAI. According to the tensile test results, with 5 mass% DLDH loading in the PAI matrix, the tensile strength increased from 51.6 to 70.8 MPa along with an increase in Young's modulus. Also the Young's modulus of PAI nanocomposite containing 5 mass% ALDH reduced from 1.95 to 0.81 GPa.     

Mechanical and thermal properties of polypeptide modified hydroxyapatite/poly(L-lactide) nanocomposites

A new type of polypeptide(poly(-benzyl-L-glutamate)(PBLG))modified hydroxyapatite(HA)/poly(L-lactide)(PLLA)nanocomposites(PBLG-g-HA/PLLA)were prepared by the solvent-mixing method,and their mechanical and thermal properties were investigated.The tensile test showed that the mechanical properties of PBLG-g-HA/PLLA nanocomposites were better than that of PLLA,even a 0.3 wt%content of PBLG-g-HA in the nanocomposites could make the tensile strength 12%higher than that of the neat PLLA sample,and the tensile mod...     

The influence of matrix crystallinity,filler grain size and modification on properties of PLA/calcium carbonate composites

Thermal and mechanical properties of polylactide (PLA) composites with different grades of calcium carbonate, 40 nm and 90 nm nanoparticles, and also with submicron particles, unmodified and modified with calcium stearate or stearic acid, obtained by melt mixing, were compared. Films with amorphous and crystalline matrices were prepared and examined.T_g of PLA in the composites remained unaffected whereas its cold crystallization was enhanced by the fillers and predominantly depended on filler content. Filling decreased thermal stability of the materials but their 5% weight loss temperatures well exceeded 250 °C, evidencing stability in the temperature range of PLA processing. The amorphous nanocomposites with modified nanoparticles exhibited improved drawability and toughness without a significant decrease of tensile strength; nearly two-fold increase of the elongation at break and tensile toughness was achieved at 5 wt% content of the modified nanofiller. Lack of surface modification of the filler, larger grain size with an average of 0.9 μm, and matrix crystallinity had a detrimental effect on the drawability. However, the presence of nanofillers and crystallinity improved tensile modulus of the materials by up to 15% compared to neat amorphous PLA.     

Three‐dimensional printing of poly(lactic acid) bio‐based composites with sugarcane bagasse fiber: Effect of printing orientation on tensile performance

The cellulose fiber was extracted from the abandoned crop sugarcane bagasse (SCB) by means of chemical treatment methods. Poly(lactic acid) (PLA) bio‐based composites with SCB were prepared through fused deposition modeling (FDM) 3D‐printing technology, and the morphologies, mechanical properties, crystallization properties, and thermal stability of 3D‐printed composites were investigated. Compared with the neat PLA, the incorporation of SCB into PLA reduces the tensile strength and flexural strength of 3D‐printed samples but increases the flexural modulus. The difference in tensile performance and bending performance is that the tensile strength of 3D‐printed samples is best when the SCB content is 6 wt%, while the flexural modulus continuously decreases as the SCB content increases. Furthermore, the effects of various printing methods on the tensile performance of 3D‐printed samples were explored via modifying G‐code of 3D models. The results indicate that the optimum SCB fiber content is identical for all printing methods except method “vertical.” Due to the fibers and molecular chains are oriented to varying degrees with altering raster angle in 3D‐printed samples, the fully oriented sample printed by method “parallel” has a better tensile strength. Besides, SCB exhibits enough high thermal decomposition temperature to meet requirements for melt extrusion processing of PLA composites, and SCB fiber is capable of promoting the crystallization of PLA.     

Electrospun hyperbranched polylactic acid–modified cellulose nanocrystals/polylactic acid for shape memory membranes with high mechanical properties

The polylactic acid (PLA) nanofiber membranes reinforced with hyperbranched PLA‐modified cellulose nanocrystals (H‐PLA‐CNCs) were prepared by electrospinning. The H‐PLA‐CNCs and the nanofiber membranes were researched by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The outcomes embodied that the cellulose nanocrystals (CNCs) could be successfully improved by the hyperbranched PLA, which would offer powerful CNCs/matrix interfacial adhesion. Thus, the mechanical and shape memory properties of PLA can be improved by adding the H‐PLA‐CNCs. In particular, when the addition of H‐PLA‐CNCs was 7 wt%, the tensile strength and an ultimate strain of PLA composite nanofiber membranes was 15.56 MPa and 25%, which was 228% and 72.4% higher than that of neat PLA, respectively. In addition, the shape recovery rate of the PLA/5 wt% H‐PLA‐CNCs composite nanofiber membrane was 93%, which was 37% higher than that of neat PLA. We expected that this present study would provide unremitting efforts for the development of more effective approaches to prepare biology basic shape memory membranes with high mechanical properties.     

Tough crystalline blends of polylactide with block copolymers of ethylene glycol and propylene glycol

The effect of crystallinity of polylactide (PLA) on the structure and properties of tough PLA blends with PEG-b-PPG-b-PEG block copolymers was studied. PLA was melt blended with a set of the copolymers with varying ratio of the hydrophilic (PEG) and hydrophobic (PPG) blocks. Although the blend phase structure depended on the copolymer molar mass and PEG content, as well as on the copolymer concentration in the blend, crystallinity also played an important role, increasing the copolymer content in the amorphous phase and enhancing phase separation. The influence of crystallinity on the thermal and mechanical properties of the blends depended on the copolymer used and its content. The blends, with PLA crystallinity of 25 ÷ 34 wt%, exhibited relatively high glass transition temperature ranging from 45 to 52 °C, and melting beginning above 120 °C. Although with a few exceptions crystallinity worsened the drawability and toughness, these properties were improved with respect to neat crystalline PLA in the case of partially miscible blends, in which fine liquid inclusions of the modifier were dispersed in PLA rich matrix. About 20-fold increase of the elongation at break and about 4-fold increase of the tensile impact strength were reached at a small content (10 wt%) of the modifier. Moreover, crystallinity decreased oxygen and water vapor transmission rates through neat PLA and the blend, and the barrier property for oxygen of the latter was better than that of neat polymer.     

The influence of organo-modified sepiolite on the flame-retardant and thermal properties of intumescent flame-retardant polylactide composites

Polylactide (PLA) composites based on intumescent flame-retardant (IFR) and organo-modified sepiolite (OSEP) were prepared via direct melt compounding. The uniform dispersion of OSEP in the PLA matrix was observed by TEM, but some agglomerates still existed at the high loading. Tensile results showed that high loading of the conventional IFR led to a reduction in tensile strength of PLA composites; however, replacing a portion of the IFR with modified sepiolite in the PLA matrix improved this result. The thermal degradation temperature of the PLA/IFR/OSEP composites determined by thermogravimetric analysis was lower than that of neat PLA, as a consequence of the catalyzed carbonization induced by the addition of IFR and OSEP. The formulation with 13 mass% IFR and 2 mass% OSEP exhibited the highest LOI value of 32 vol% and also reached UL-94 V-0 rating in the vertical burning tests. Furthermore, the co-addition of IFR and OSEP gave rise to a significant reduction in peak heat release rate (PHRR) and total heat release (THR) of PLA composites during combustion, particularly in the case of PLA/IFR13/OSEP2 (82% reduction in PHRR and 69% in THR). The excellent fire resistance of PLA/IFR13/OSEP2 could be attributed to that IFR catalyzed carbonization of PLA to form the char, while OSEP resulted in further stabilization in the charred layers.     

Thermal and mechanical properties of cassava and pineapple flours-filled PLA bio-composites

The research focused on enhancing the mechanical properties and thermal stability of bio-composites with natural flours and improving the interfacial adhesion between biodegradable polymer and flour. The tensile and flexural strength of the PLA bio-composites decreased with increasing flour addition. However, a 3% loading of the compatibilizer in the PLA bio-composite increased this strength up to that observed with the 10% loading flour. The degradation temperature of PLA was decreased by the flour but destarched cassava flour had higher thermal stability on account of its higher lignin content than pineapple flour. This means that the PLA bio-composites with destarched cassava flour had higher thermal stability than those with the pineapple flour. In addition, the thermal degradation temperature was increased by adding MAPLA. The compatibilizer improved the crystallinity of PLA, which enhanced the mechanical strength of the PLA bio-composites. As the pineapple flour and destarched cassava flour 30% loading was increased, the HDT of the PLA bio-composites increased from 56.8?°C to ~66.3 and 69.7?°C, respectively. The thermal aging test showed no reduction in strength of the neat PLA. However, the PLA bio-composites showed a gradual decrease in tensile strength with increasing number of cycles. Moreover, the shrinkage ratio of the neat PLA was 5% of that found with the PLA resin.     

The effects of dioctyl phthalate plasticization on the morphology and thermal,mechanical, and rheological properties of chemical crosslinked polylactide

The tensile strength and thermal stability of polylactide (PLA) were significantly improved through chemical crosslinking. However, it became much more rigid and brittle. To obtain a material with good thermal stability and enhanced ability to plastic deformation, chemical crosslinked PLA with 0.5 wt % triallyl isocyanurate and 0.5 wt % dicumyl peroxide was blended with different contents of dioctyl phthalate (DOP). The advantage of using DOP is that it does not crystallize, has low glass transition temperature, and is miscible with PLA. The morphology and the thermal and mechanical properties of the crosslinked PLA and the blends of crosslinked PLA with various contents of DOP were investigated by means of scanning electron microscope, differential scanning calorimetry, tensile test, and dynamic mechanical analysis. The rheological properties of samples were also explored by using a capillary rheometer. The results showed that the DOP was an effective plasticizer for the chemical crosslinked PLA, resulting in a significantly decreased T_g, lower yield stress, and improved elongation at break. The plasticization effect was enhanced by adding higher DOP content. In addition, the DOP enhanced the crystallinity of crosslinked PLA, and all the crosslinked samples showed better heat stability than neat PLA. The apparent viscosity of the blends decreased with the increase of DOP content and a phase separation occurred when the content of DOP exceeded 12.5 wt %. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1136–1145, 2009     

Preparation of PLA-based nanocomposites modified by nano-attapulgite with good toughness-strength balance

Polylactic acid (PLA) was modified by poly (butylene adipate-co-terephthalate) (PBAT) and nano-attapulgite (AT) using the melt blending technique. Ethylene-butyl acrylate-glycidyl methacrylate (E-BA-GMA) was used as a compatibilizer which can bond the AT nanoparticles with PLA/PBAT matrix by interaction between the epoxy and hydroxyl groups. The effects of the AT content on the mechanical properties, thermal properties, crystallinity and morphology of PLA/PBAT/ATT nanocomposites were investigated. The results showed that the tensile strength, elongation at break and impact strength of PLA/PBAT could be simultaneously increased by incorporating AT nanoparticles. PLA/PBAT/AT nanocomposites possessed higher thermal stability than pure PLA/PBAT. In the ternary composite system of PLA/PBAT/AT, AT acted as a heterogeneous nucleating agent and was able to increase the crystallization temperature. When the AT content was low (≤2.5 wt%), AT nanoparticles could uniformly disperse in the PLA/PBAT matrix. In general, AT was an effective filler to reinforce and toughen PLA/PBAT blend simultaneously, and the PLA/PBAT/AT nanocomposite with 2.5 wt% AT exhibited a good combination of strength and toughness.     

Effect of a phosphorus-containing flame retardant on the thermal properties and ease of ignition of poly(lactic acid)

An aryl polyphenylphosphonate, poly(9-oxa-10-(2,5-dihydro-xyphenyl) phospha-phenanthrene-10-oxide) phenylphosphonate (WLA-3), was used to prepare a flame-retardant poly(lactic acid) (PLA) by direct melt compounding. The thermal behaviour, burning behaviour and mechanical properties of the flame-retardant PLA systems have been investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), vertical burning test (UL-94), limiting oxygen index (LOI), cone calorimeter test (CCT) and tensile test. The flame retardance mechanism has been studied via Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC), and P content analysis. The UL-94 ratings of PLA’s containing 7phr (W_7P) and 10phr (W_10P) of WLA-3 were enhanced to V-0 from no rating for neat PLA. However, the cone calorimetry of flame-retardant PLA (W_7P) only showed a little decrease in heat release rate (HRR), peak of heat release rate (PHRR) and total heat release (THR) compared to neat PLA. TGA results showed that the PLA containing different amounts of WLA-3 presented more complicated thermal decomposition behaviours than neat PLA. Additionally, the results from DSC and tensile tests showed that the addition of WLA-3 into PLA had a slight impact on the crystallization behaviours and tensile properties.     

Influences of poly(lactic acid)‐grafted carbon nanotube on thermal,mechanical, and electrical properties of poly(lactic acid)

Poly(lactic acid)‐grafted multiwalled carbon nanotubes (MWNT‐g‐PLA) were prepared by the direct melt‐polycondensation of L ‐lactic acid with carboxylic acid‐functionalized MWNT (MWNT‐COOH) and then mixed with a commercially available neat PLA to prepare PLA/MWNT‐g‐PLA nanocomposites. Morphological, thermal, mechanical, and electrical characteristics of PLA/MWNT‐g‐PLA nanocomposites were investigated as a function of the MWNT content and compared with those of the neat PLA, PLA/MWNT, and PLA/MWNT‐COOH nanocomposites. It was identified from FE‐SEM images that PLA/MWNT‐g‐PLA nanocomposites exhibit good dispersion of MWNT‐g‐PLA in the PLA matrix, while PLA/MWNT and PLA/MWNT‐COOH nanocomposites display MWNT aggregates. As a result, initial moduli and tensile strengths of PLA/MWNT‐g‐PLA composites are much higher than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, which stems from the efficient reinforcing effect of MWNT‐g‐PLA in the PLA matrix. In addition, the crystallization rate of PLA/MWNT‐g‐PLA nanocomposites is faster than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, since MWNT‐g‐PLA dispersed in the PLA matrix serves efficiently as a nucleating agent. It is interesting that, unlike PLA/MWNT nanocomposites, surface resistivities of PLA/MWNT‐g‐PLA nanocomposites did not change noticeably depending on the MWNT content, demonstrating that MWNTs in PLA/MWNT‐g‐PLA are wrapped with the PLA chains of MWNT‐g‐PLA. Copyright © 2008 John Wiley & Sons, Ltd.     

Fabrication of 3D electrospun structures from poly(lactide‐co‐glycolide acid)–nano‐hydroxyapatite composites

The fabrication of three‐dimensional (3D) electrospun composite scaffolds was presented in this study. Layers of electrospun meshes made from composites of poly(lactide‐co‐glycolide acid) (PLGA) and hydroxyapatite (HA) were stacked and sintered using pressurized gas. Three HA concentrations of 5, 10, and 20 wt % were tested, and the addition of the HA nanoparticles decreased the tensile mechanical properties of the meshes with 20 wt % HA. However, after the gas absorption process, the fibers within the mesh sintered, which improved the mechanical properties more than twofold. The fabrication of 3D, porous, electrospun scaffolds was also demonstrated. The resulting 3D scaffolds had open porosity of up to 70% and modulus of ～20 MPa. This technique improves on the current electrospinning technology by overcoming the challenges of depositing a thick, 3D structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Mechanical,thermal, and UV‐shielding behavior of silane surface modified ZnO‐reinforced phthalonitrile nanocomposites

In the present work, zinc oxide nanoparticles were treated with aminopropyl trimethoxy silane‐coupling agent and used as a new kind of reinforcement for a typical high performance bisphenol‐A‐based phthalonitrile resin. The resulted nanocomposites were characterized for their mechanical, thermal, and optical properties. Results from the tensile test indicated that the tensile strength and modulus as well as the toughness state of the matrix were all enhanced with the increasing of the nanoparticles amount. Thermogravimetric analysis showed that the starting decomposition temperatures and the residual weight at 800°C were highly improved upon adding the nanofillers. At 6 wt% nanoloading, the glass transition temperature and the storage modulus were considerably enhanced reaching about 359°C and 3.7 GPa, respectively. The optical tests revealed that the neat resin possesses excellent UV‐shielding properties, which were further enhanced by adding the nanofillers. Furthermore, the fractured surfaces of the nanocomposites analyzed by scanning electron microscope exhibited homogeneous and rougher surfaces compared with that of the pristine resin. Finally, the good dispersion of the reinforcing phase into the matrix was confirmed by a high resolution transmission electron microscope. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhanced directional thermal conductivity of polylactic acid/polybutylene adipate terephthalate ternary composite filled with oriented and surface treated boron nitride

A combination of solution casting and melt extrusion technique was used to fabricate Boron nitride (BN)-filled Polylactic acid (PLA)/polybutylene adipate terephthalate (PBAT) blend composites. The BN particles were surface treated with a silane coupling agent and functionalization was confirmed via spectroscopic analysis. Field emission scanning electron microscopy confirmed that the BN surface treatment improved the particle adhesion with the polymer matrices and acted as a compatibilizer for the polymers. Moreover, changes in the particle orientation in the blend composite yielded improved thermal conductivity in different directions. The inclusion of the treated BN particles enhanced the in-plane (~1.1 W m⁻¹K⁻¹) and through-plane (~0.8 W m⁻¹K⁻¹) thermal conductivity of the composites as compared to the neat PLA. In addition, the storage modulus of the composite become more than 3 GPa that is twice that of the PLA/PBAT blend with a reasonable tensile property. In general, compared with the PLA/PBAT blend, the blend composites exhibited superior thermal and mechanical properties.     

Simultaneously improving the flame retardancy and mechanical properties for polyamide 6/aluminum diethylphosphinate composites by incorporating of 1,3,5‐triglycidyl isocyanurate

The effect of 1,3,5‐triglycidyl isocyanurate (TGIC) as a synergistic agent on the fire retardancy, thermal, and mechanical properties for polyamide 6/aluminium diethylphosphinate (PA6/AlPi) composites were investigated in detail by limiting oxygen index; vertical burning (UL‐94); cone calorimeter; thermal gravimetric analysis; rheological measurements; and the tests of tensile, flexural, and Izod impact strength. The morphologies and chemical compositions of the char residue were investigated by scanning electron microscopy, X‐ray photoelectron spectroscopy, and Fourier transform infrared spectra. The results demonstrated that AlPi and TGIC exerted an evident synergistic effect for flame retardant PA6 matrix, and the PA6/AlPi/TGIC composites with the thickness of 1.6 mm successfully passed UL‐94 V‐0 rating with the limiting oxygen index value of 30.8% when the total loading amount of AlPi/TGIC with the mass fraction of 97:3 was 11 wt%. However, the samples failed to pass the UL‐94 vertical burning tests when AlPi alone is used to flame retardant PA6 matrix with the same loading amount. The thermal gravimetric analysis data revealed that the introduction of TGIC promoted the char residue formation at high temperature. The rheological measurement demonstrated that the incorporation of TGIC improved the storage modulus, loss modulus, and complex viscosity of PA6/AlPi/TGIC composites comparing with that of neat PA6 and PA6/AlPi composites due to the coupling reaction between TGIC and the terminal groups of PA6 matrix. The morphological structures of char residues demonstrated that TGIC benefited to the formation of more homogenous and integrated char layer with no defects and holes on the surface comparing with that of PA6/AlPi composites during combustion. The higher melt viscosity of composites and the integrated and sealed char layer effectively inhibited the volatilization of flammable gas into the combustion zone and then led to the reduction of the heat release. The results of mechanical properties revealed that the incorporation of TGIC enhanced the mechanical properties for PA6/AlPi/TGIC composites comparing with that of PA6/AlPi composites with the same loading amount of flame retardant caused by the chain extension effect of TGIC. As a result, the flame retardancy and mechanical properties of PA6/AlPi composites simultaneously enhanced due to the introduction of TGIC.     

PLA-ZnO nanocomposite films: Water vapor barrier properties and specific end-use characteristics

PLA nanocomposite films with multifunctional characteristics such as mechanical, anti-UV, antibacterial, electrical, gas barrier properties are potentially of high interest as packaging biomaterials. Occasionally, desired and beneficial effects obtained by addition nanofillers come along with some drawbacks, leading to the sharp drop in the molecular weights of the polyester chains, and consequently an important loss of mechanical and thermal properties. Novel PLA-ZnO nanocomposite films were produced by melt-compounding PLA with 0.5–3% ZnO rod-like nanoparticles. The surface treatment of nanofiller by silanization (with triethoxy caprylylsilane) was necessary to obtain a better dispersion and to limit the decrease of molecular mass of PLA. The morphology, molecular, thermo-mechanical and transport properties to water vapor of PLA-ZnO films were analyzed with respect to the neat PLA. According to DSC and to XRD, the produced films were essentially amorphous. The changes in PLA permeation properties were strongly dependent on temperature and nanofiller loading. The well dispersed ZnO nanoparticles within the polyester matrix were effective in increasing the tortuosity of the diffusive path of the penetrant molecules. The activation energy remained similar for PLA and PLA-1% ZnO, but was found greater at higher loading of ZnO (3%), confirming the increased difficulty of travelling molecules to diffuse through PLA. In comparison to the neat PLA (presenting no antimicrobial efficacy), the nanocomposites were active against both Gram-positive and Gram-negative bacteria, stronger antibacterial activity being evidenced after 7 days elapsed time. By considering the multifunctional properties of PLA-ZnO nanocomposites, the films produced by extrusion can be considered a promising alternative as environmental-friendly packaging materials.