Electrical resistance and heat generation of polypyrrole‐coated polyacrylonitrile nanofibrous and regular fibrous mats

This article reports the effect of fiber diameter on the electrical resistance and heat generation of fibrous polyacrylonitrile (PAN) mats coated with polypyrrole during chemical in situ polymerization. Polypyrrole is one of the important intrinsically conducting polymers that perform similar to semiconductors. The electrical resistance of polypyrrole‐coated mats depends on the fiber diameter, the applied pressure on the surface of the mats, and the mat thickness. The electrical resistance of polypyrrole‐coated PAN fibrous mats decreases as fiber diameter decreases. Moreover, electrical resistance decreases considerably as the mat thickness as well as the applied pressure on it increases. It was also observed that the heat generated in polypyrrole‐coated PAN fibrous mats increases with voltage and duration of the applied voltage. Lower fiber diameter also leads to higher heat generation. Furthermore, electrical current increases rapidly in the initial stages of applying voltage and then shows a marginal increase. Considering their high specific surface area, nanofibers convey considerable improvement in the electrical conductivity as well as heat generation capacity of the mats made from them. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly (indene‐co‐pyrrole) nanofibers

Nanofibers of poly (indene‐co‐pyrrole) (CInPy) have been synthesized, using a facile chemical oxidative polymerization reaction. The effect of copolymerization was examined in view of the individually synthesized homopolymer nanostructures of polyindene (PIn) and polypyrrole (PPy). Morphological details of CInPy, studied using scanning electron microscopy (SEM) and transmission electron microscopy, (TEM) reveal the appearance of dense cottony mess, comprising of fine fibers with an average diameter of 5–10 nm. Chemical structural analysis of CInPy, conducted using ultraviolet‐visible (UV‐Vis), Fourier transform infrared (FTIR), and nuclear magnetic resonance (NMR) spectroscopic techniques, reveals that both PIn and PPy are involved in the formation of copolymer organization. Fluorescence properties of nanosized copolymer are observed in the blue region, with emission λ_max placed at 395 nm. Conductivity of copolymer nanofibers (2.4 × 10^?3 S/cm) is consistent with the morphology and thermal stability properties of integral homo‐polymers. Improved thermal stability and processability along with the enhanced optical and electrical properties of copolymer nanostructures outfit it as a better promising material in optoelectronic and light emitting nanodevices, with reference to nanosized PIn and PPy. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel germanium‐containing poly(p‐phenylenevinylene) derivatives

Novel blue‐emitting germanium‐containing poly(p‐phenylenevinylene) (PPV) derivatives with well‐defined conjugation lengths were synthesized via Wittig‐condensation polymerizations. The polymers can be color‐tuned by the introduction of various chromophores into the PPV‐based polymer backbones. The photoluminescence (PL) spectra of the polymers, GePVK (containing carbazole moieties), GeMEH (containing dialkoxybenzene moieties), and GePTH (containing phenothiazine moieties), were found to exhibit blue, greenish blue, and green emissions, respectively. GePTH produces more red‐shifted emission than GeMEH and GEPVK, resulting in green emission, and the solution and solid state PL spectra of GePVK consist of almost blue emission. The electroluminescence spectra of GeMEH and GePTH contain yellowy green and yellow colors, respectively. Interestingly, GePVK exhibits white emission with CIE coordinates of (0.33, 0.37) due to electroplex emission in the light‐emitting diodes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 979–988, 2008     

Synthesis and characterization of novel h‐HTBN/PEG PU copolymers: effect of surface properties on hemocompatibility

This work reported the hydrophilicity, hemocompatibility, and cytotoxicity of novel polyurethane (PU) scaffolds for tissue engineering, especially the hydrolysis effect of a soft‐segmented component, a hydrolytically‐modified hydroxyl‐terminated poly(butadiene‐co‐acrylonitrile) (h‐HTBN), on these properties. The PU copolymers were prepared by coupling poly(ethylene glycol) (PEG) with the h‐HTBN together with the help of 1,1‐methylene bis‐(4‐isocyanatocyclohexane) as a bridging reagent. The structure of PU copolymers was characterized by Fourier transformation infrared spectrometry (FTIR). The experimental results indicated that the hydrolytically‐modified HTBN increases water absorption and decreases water contact angles, improving surface hydrophilicity. The synthesized h‐HTBN/PEG PU copolymers display low hemolysis activity, and a little amount of platelet adhesion and activation, implying good compatibility. The methyl tretrazolium (MTT) assays elicited that the cytotoxicity is related to the component ratios of h‐HTBN to PEG and the hydrolysis modification of HTBN. The PU scaffolds can be employed as potential candidates for blood contacting applications. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis,characterization, and thermal properties of a novel pentaerythritol‐initiated star‐shaped poly(p‐dioxanone)

A novel star‐shaped poly(p‐dioxanone) was synthesized by the ring‐opening polymerization of p‐dioxanone initiated by pentaerythritol with stannous octoate as a catalyst in bulk. The effect of the molar ratio of the monomer to the initiator on the polymerization was studied. The polymers were characterized with ¹H NMR and ¹³C NMR spectroscopy. The thermal properties of the polymers were investigated with differential scanning calorimetry and thermogravimetric analysis. The novel star‐shaped poly(p‐dioxanone) has a potential use in biomedical materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1245–1251, 2006     

Synthesis and characterization of a poly(p‐phenylenediamine)‐based electrospun nanofiber for the micro‐solid‐phase extraction of organophosphorus pesticides from drinking water and lemon and orange juice samples

A new micro‐solid‐phase extraction sorbent was synthesized by electrospinning poly(p‐phenylenediamine)/poly(vinyl alcohol) in the presence of cetyltrimethylammonium bromide. The modified nanofiber was prepared by removing the majority of the poly(vinyl alcohol) from the nanofiber blend by exposing it to the hot water. Scanning electron microscopy and surface analysis were performed to study the homogeneity and porosity of the electrospun nanofiber. In addition, Fourier transform infrared spectroscopy was applied for more characterization. The capability of the new nanofiber was explored by applying it in the extraction and preconcentration of organophosphorus pesticides from aqueous medium. After solvent desorption, the extracted analytes were analyzed by high‐performance liquid chromatography with diode array detection. Under the optimum conditions, the relative standard deviation values at the concentration level of 50 ng/mL were in the range of 4.8–8.3%. The calibration curve showed linearity in the range of 0.5–500 ng/mL, and the limits of detection (S/N = 3) for the studied compounds were 0.15 ng/mL. By analyzing Tehran drinking water, lemon juice, sour lemon juice, orange juice and sour orange juice, the applicability of the presented method was investigated and the relative recoveries were in the range of 76–102%.     

Synthesis and characterization of novel biodegradable epoxy‐modified polyurethane elastomers

Biodegradable polyurethane elastomers with the potential for applications in medical implants were synthesized from the reaction of epoxy‐terminated polyurethane prepolymers (EUPs) with 1,6‐hexamethylenediamine as a curing agent. EUPs were themselves prepared from the reaction of glycidol and isocyanate‐terminated polyurethanes made from different molecular weights of poly(ε‐caprolactone) (CAPA) and 1,6‐hexamethylene diisocyanate. All materials were characterized by spectroscopic methods. The curing conditions were optimized by gel content measurements. The curing kinetic and kinetic parameters were determined from differential scanning calorimetry measurements. The effects of changing the crosslink density and crystallinity of elastomers via the alteration of the CAPA polyol molecular weight on the physical, mechanical, and degradation properties of the final elastomeric polymers were examined fully. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2985‐2996, 2005     

Synthesis and characterization of poly(urethane‐benzoxazine) films as novel type of polyurethane/phenolic resin composites

Poly(urethane‐benzoxazine) films as novel polyurethane ( PU )/phenolic resin composites were prepared by blending a benzoxazine monomer ( Ba ) and PU prepolymer that was synthesized from 2,4‐tolylene diisocyanate (TDI) and polyethylene adipate polyol (MW ca. 1000) in 2 : 1 molar ratio. DSC of PU/Ba blend showed an exotherm with maximum at ca. 246 °C due to the ring‐opening polymerization of Ba, giving phenolic OH functionalities that react with isocyanate groups in the PU prepolymer. The poly(urethane‐benzoxazine) films obtained by thermal cure were transparent, with color ranging from yellow to pale wine with increase of Ba content. All the films have only one glass transition temperature (T_g ) from viscoelastic measurements, indicating no phase separation in poly(urethane‐benzoxazine) due to in situ polymerization. The T_g increased with the increase of Ba content. The films containing 10 and 15% of Ba have characteristics of an elastomer, with elongation at break at 244 and 182%, respectively. These elastic films exhibit good resilience with excellent reinstating behavior. The films containing more than 20% of Ba have characteristics of plastics. The poly(urethane‐benzoxazine) films showed excellent resistance to the solvents such as tetrahydrofuran, N,N‐dimethyl formamide, and N‐methyl‐2‐pyrrolidinone that easily dissolve PU s. Thermal stability of PU was greatly enhanced even with the incorporation of a small amount of Ba . © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4165–4176, 2000     

Synthesis and characterization of novel aromatic polyimides from 4,4‐bis(p‐aminophenoxymethyl)‐ 1‐cyclohexene

A novel diamine, 4,4‐bis(p‐aminophenoxymethyl)‐1‐cyclohexene (CHEDA), was synthesized from 4,4‐bis(hydroxymethyl)‐1‐cyclohexene and p‐chloronitrobenzene by nucleophilic aromatic substitution and subsequent catalytic reduction of the intermediate dinitro compound. A series of aromatic polyimides were prepared from CHEDA and commercial dianhydrides with varying flexibility and electronic character in two‐step direct polycondensation reactions. High molecular weight polyimides with intrinsic viscosities between 0.57 and 10.2 dL/g were obtained. Most of these polyimides, excluding those from PMDA and BPDA, were soluble in polar aprotic solvents such as NMP and DMAc, and many were also soluble in CHCl₃ and THF. DSC analysis revealed glass transitions in the range of 190 to 250°C. No significant weight losses occurred below 450°C in nitrogen and 350°C in air. Bromination and epoxidation of cyclohexene double bond in CHDEA–6FDA (3e) were investigated as examples of possible polymer modifications. Qualitative epoxidation and selective bromination of the double bond were demonstated. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1189–1197, 1999     

Synthesis and characterization of novel nano size electroactive poly 4,4′‐diaminodiphenyl sulphone

The modification of electrodeposited polyaniline film by subsequent electrodeposition of 4,4′‐diaminodiphenyl sulfone (DDS) leads to a new material having nanostructure. The coated polymer films were treated with various pH solutions. The film adherent characteristics and surface morphology were studied using SEM. The electrochemically synthesized polyDDS revealed good redox behavior. The DDS was also polymerized by the chemical oxidation method using potassium persulphate. The polymer was characterized by UV‐Vis and FTIR spectral studies. The formation of polymer through the N? H group was understood from the single N? H stretching vibrational frequency at 3459 cm^?1. The X‐ray diffraction studies revealed the formation of nano sized (28 nm) crystalline polymer. The conductivity of the polymer was determined to be 1.07 × 10^?4 S.cm^?1. The solubility of the chemically polymerized powder was ascertained, and polyDDS showed good solubility in DMF and DMSO. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1702–1707, 2005     

Preparation and characterization of a novel biodegradable poly(p‐dioxanone)/montmorillonite nanocomposite

Poly(p‐dioxanone) (PPDO)/montmorillonite nanocomposites were prepared through the in situ ring‐opening polymerization of p‐dioxanone (PDO) and three types of montmorillonites (natural sodium montmorillonite, montmorillonite modified by octadecyltrimethyl ammonium chloride, and montmorillonite modified by hydroxyethylhexadecyldimethyl ammonium bromine) in the presence of triethylaluminum. Montmorillonite could accelerate the polymerization of PDO, and the viscosity‐average molecular weight of PPDO could reach 44,900 g/mol in 0.5 h. A nucleating effect of montmorillonite was observed, and the crystallization temperature of PPDO was increased by 18 °C. All three montmorillonites could improve the thermal stability of PPDO and increase the glass‐transition and melting temperatures of PPDO. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2298‐2303, 2005     

Synthesis and characterization of novel fluorinated polyurethane elastomers based on 2,2‐bis[4‐(4‐amino‐2‐trifluoromehyloxyphenyl) phenyl]propane

2,2‐Bis[4‐(4‐amino‐2‐trifluoromehyloxyphenyl) phenyl]propane (BAFPP) was synthesized based on 2‐chlorobenzotrifluoride and bisphenol A and characterized by Fourier transform infrared spectroscopy and nuclear magnetic resonance. BAFPP was used as a chain extender to prepare a series of fluorine‐containing polyurethane elastomers (FPUEs) with different fluorine contents by changing the soft segments and isocyanate index (R). The FPUEs were investigated by water absorption, contact angle, X‐ray photoelectron spectroscopy, thermogravimetric analysis, and microscale combustion calorimetry. The results show that the FPUEs prepared from BAFPP were elastomers that have low surface tension, low water absorption, and good thermal stability. Furthermore, FPUEs also exhibit good flame resistance, and the peak heat release rate of FPUE based on BAFPP (282.9 W/g) is much lower than that of polyurethane elastomer without the F element (537.2 W/g). Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel electroactive polyamides and polyimides with bulky 4‐(1‐adamantoxy)triphenylamine moieties

A novel adamantoxytriphenylamine‐containing diamine monomer, 4‐(1‐adamantoxy)‐4′,4″‐diaminotriphenylamine, was synthesized from readily available reagents. Two series of novel electroactive aromatic polyamides and polyimides with bulky 4‐(1‐adamantoxy)triphenylamine moieties were prepared from the newly synthesized diamine monomer with various aromatic dicarboxylic acids and tetracarboxylic dianhydrides, respectively. All the resulting polyamides and most of the polyimides were readily soluble in polar organic solvents and could be solution cast into tough and flexible films. These polymers showed moderate to high glass transition temperatures in the range of 263–311 °C, and they were fairly stable up to a temperature above 480 °C (for polyamides) or 500 °C (for polyimides). Cyclic voltammograms of the polyamides and polyimides showed one pair of reversible redox waves with oxidation half‐wave potentials (E_1/2) in the range of 0.78–0.81 and 0.97–1.05 V, respectively, versus Ag/AgCl in an acetonitrile solution. In addition, the polymers were found to display stable electrochromic properties by repeated cyclic scans between 0.0 and 1.1–1.2 V, with coloration change from a colorless or pale yellowish neutral form to a dark blue or bluish green oxidized form. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1740–1755, 2009     

Water‐soluble poly(ethylene oxide)‐block‐poly(p‐phenylene vinylene) copolymer: Synthesis and characterization

Water‐soluble and photoluminescent block copolymers [poly(ethylene oxide)‐block‐poly(p‐phenylene vinylene) (PEO‐b‐PPV)] were synthesized, in two steps, by the addition of α‐halo‐α′‐alkylsulfinyl‐p‐xylene from activated poly(ethylene oxide) (PEO) chains in tetrahydrofuran at 25 °C. This copolymerization, which was derived from the Vanderzande poly(p‐phenylene vinylene) (PPV) synthesis, led to partly converted PEO‐b‐PPV block copolymers mixed with unreacted PEO chains. The yield, length, and composition of these added sequences depended on the experimental conditions, namely, the order of reagent addition, the nature of the monomers, and the addition of an extra base. The addition of lithium tert‐butoxide increased the length of the PPV precursor sequence and reduced spontaneous conversion. The conversion into PPV could be achieved in a second step by a thermal treatment. A spectral analysis of the reactive medium and the composition of the resulting polymers revealed new evidence for an anionic mechanism of the copolymerization process under our experimental conditions. Moreover, the photoluminescence yields were strongly dependant on the conjugation length and on the solvent, with a maximum (70%) in tetrahydrofuran and a minimum (<1%) in water. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4337–4350, 2005     

Synthesis and characterization of novel poly(p‐phenylenevinylene) derivatives containing phenothiazine‐5‐oxide and phenothiazine‐5, 5‐dioxide moieties

PPV‐based copolymers containing phenothiazine‐5‐oxide and phenothiazine‐5, 5‐dioxide moieties have been successfully synthesized by Wittig‐Horner reaction and characterized by means of UV‐vis, photoluminescence, electroluminescence spectra, and cyclic voltammetry. All of these copolymers can be dissolved in common organic solvents such as chloroform, tetrahydrofuran, and toluene. The PL maxima in the film state are located at 582, 556, and 552 nm for P1, P2, and P3, respectively. The HOMO and LUMO levels of P2 are found to be ?5.21 and ?2.68 eV, respectively; whereas those of P3 are found to be ?5.26 and ?2.71 eV, respectively. The cyclic voltammetry result indicates that the conversion of electron‐donating sulfide to electron‐withdrawing sulfoxide or sulfone group in polymers plays a dominating role in increasing its oxidation potential. Yellowish‐green light ranging from 568 to 540 nm was observed for the single layer device with the configuration of ITO/Polymer/Ca/Al. Double layer devices with Zn (BTZ)₂ as a hole blocking layer exhibited enhanced EL performance compared to the single layer devices. The maximum brightness of the double layer devices of P1, P2, and P3 is 278, 400, and 796 cd/m², respectively. The results of EL and electrochemical analyses revealed that they are promising candidate materials for organic, light‐emitting diodes with hole‐transporting ability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4291–4299, 2007     

Direct Electroanalysis of p‐Nitrophenol (PNP) in Estuarine and Surface Waters by a High Sensitive Type C/p‐NiTSPc Coating Carbon Fiber Microelectrode (CFME)

We report for the first time on the elaboration of a remarkable sensitivity type C/p‐NiTSPc carbon fiber microelectrode (CFME) for p‐nitrophenol (PNP) pollutant. We observed the best performances using square wave voltammetry (SWV) technique in the place of differential pulse voltammetry (DPV). Also the combination of p‐NiTSPc optimized cycles of electrodeposition and accumulation time, helped us to increase remarkably the sensor slope (320 times) and the limit of detection (LOD) (1000 times), with a final LOD of 0.1 µg/L, the current regulatory limit for drinkable waters. Furthermore the recoveries of the standards added are close to 100 % indicating that the method has some suitability. The proposed voltammetric procedure might be applied for organophosphorus pesticides and their by‐products with a remarkable sensing in natural polluted waters.     

Formation of Silica/Poly(p‐dioxanone) Microspheres by Surface‐Initiated Polymerization

A polymeric film of a biodegradable poly(p‐dioxanone) was grown from 490 nm silica particles by monolayer formation via self‐assembly of hydroxy‐terminated triethoxysilane and subsequent surface‐initiated ring‐opening polymerization of p‐dioxanone. The resulting silica/poly(p‐dioxanone) hybrid particles were characterized by means of ¹H NMR spectroscopy, IR spectroscopy, thermogravimetric analysis, field‐emission scanning electron microscopy, and energy‐dispersive X‐ray spectroscopy.

     

Synthesis and film formation of polycarbonate‐co‐ poly(p‐ethylphenol)

The enzyme‐catalyzed synthesis of poly(p‐ethylphenol) (PEP) has received considerable interest in recent years. Nevertheless, the limited molecular weights restricts its application. In our preliminary research, PEP was modified by copolymerization with polycarbonates through both transesterification at high temperature, and triphosgene at low temperature to form polycarbonate‐co‐poly(p‐ethylphenol) (PC‐co‐PEP). FTIR, NMR, GPC, and thermal analysis verified the formation of PC‐co‐PEP. The copolymers have an optical absorption in the UV range. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 169–178, 1999     

Efficient removal of As(V) from simulated arsenic-contaminated wastewater via a novel metal–organic framework material: Synthesis,structure, and response surface methodology

A novel metal–organic framework material {[N(C₂H₅)₃][Zn₂(ptmda)₂(μ₂-H₂O)]·(H₂O)_0.5}_n { GUT-3 ; H₂ptmda is 4,4′-([p-tolylazanediyl]bis [methylene])dibenzoic acid} was successfully synthesized using the hydrothermal method and characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. GUT-3 has a two-dimensional network based on dinuclear [Zn₂(ptmda)₂(μ₂-H₂O)]⁻ building units which formed an eightfold interpenetration network in GUT-3 molecules. Hirshfeld surface analysis revealed that H–H, C–H, and O–H bonds accounted for the majority of intermolecular interactions. Moreover, the interactions between GUT-3 and As(V) – the form of As(V) is AsO₄³⁻ – were analyzed in aqueous solutions in a batch system to study the effect of pH, concentration, adsorbent dose, adsorption time, adsorption temperature, and shaking speed. The kinetic and isotherm data of arsenic adsorption on GUT-3 were accurately modeled by pseudo-second-order, Langmuir (q_m = 33.91 mg/g), and Freundlich models. The Box–Behnken response surface method was used to optimize the adsorption conditions of As(V) from the simulated arsenic-contaminated wastewater. The effect of various experimental parameters and optimal experimental conditions was ascertained using the quadratic model.