Thin poly(ionic liquid) and poly(vinylidene fluoride) blend films with ferro‐ and piezo‐electric polar γ‐crystals

Ferro‐ and piezo‐electric poly(vinylidene fluoride) (PVDF) thin film is reported to be obtained by using a poly(ionic liquid) (PIL) [poly(2‐(dimethylamino)ethyl methacrylate) methyl chloride quaternary salt] through solution route. The short range interactions between localized cationic ions of PIL and polar >CF₂ of PVDF are responsible for modified polar γ‐PVDF (T₃GT₃Ḡ) formation. Modification in chain conformation of PVDF is confirmed by FTIR, XRD, and DSC studies suggesting the miscible PVDF–PIL (PPIL) blend. Up to 40 wt % loading of PIL in PVDF matrix enhances relative intensity of γ‐phase up to 50% in the entire crystalline phase. The P‐E hysteresis loop of PVDF‐PIL blends at 25 wt % PIL loading (PPIL‐25) thin film at sweep voltage of ±50 V shows excellent ferroelectric property with nearly saturated high remnant polarization ∼6.0 µC cm⁻² owing to large proportion of γ‐PVDF. However, non‐polar pure PVDF thin film shows unsaturated hysteresis loop with 1.4 µC cm⁻² remnant polarization. The operation voltage decreases effectively because of the polar γ‐phase formation in PPIL blended film. High‐sensitivity piezo‐response force microscopy shows electromechanical switching property at low voltages in PPIL‐25 thin films through local switching measurements, making them potentially suitable as ferroelectric tunnel barriers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 795–802     

Hydrolytic degradation of poly(ε‐caprolactone) with different end groups and poly(ε‐caprolactone‐co‐γ‐butyrolactone): characterization and kinetics of hydrocortisone delivery

Asymmetric telechelic α‐hydroxyl‐ω‐(carboxylic acid)‐poly(ε‐caprolactone) (HA‐PCL), α‐hydroxyl‐ω‐(benzylic ester)‐poly(ε‐caprolactone) (HBz‐PCL), and an asymmetric telechelic copolymer α‐hydroxyl‐ω‐(carboxylic acid)‐poly(ε‐caprolactone‐co‐γ‐butyrolactone) (HA‐PCB) were synthesized by ring‐opening polymerization of ε‐caprolactone (CL). CL and CL/γ‐butyrolactone mixture were used to obtain homopolymers and copolymer respectively at 150°C and 2 hr using ammonium decamolybdate (NH₄) [Mo₁₀O₃₄] (Dec) as a catalyst. Water (HA‐PCL and HA‐PCB) or benzyl alcohol (HBz‐PCL) were used as initiators. The three polylactones reached initial molecular weights between 2000 and 3000 Da measured by proton nuclear magnetic resonance (¹H‐NMR). Compression‐molded polylactone caplets were allowed to degrade in 0.5 M aqueous p‐toluenesulfonic acid at 37°C and monitored up to 60 days for weight loss behavior. Data showed that the copolymer degraded faster than the PCL homopolymers, and that there was no difference in the weight loss behavior between HA‐PCL and HBz‐PCL. Caplets of the three polylactones containing 1% (w/w) hydrocortisone were placed in two different buffer systems, pH 5.0 with citrate buffer and pH 7.4 with phosphate buffer at 37°C, and monitored up to 50 days for their release behavior. The release profiles of hydrocortisone presented two stages. The introduction of a second monomer in the polymer chain significantly increased the release rate, the degradation rate for HA‐PCB being faster than those for HBz‐PCL and HA‐PCL. At the pH studied, only slight differences on the liberation profiles were observed. SEM micrographs indicate that hydrolytic degradation occurred mainly by a surface erosion mechanism. Copyright © 2009 John Wiley & Sons, Ltd.     

A convenient synthesis of α,α′‐ homo‐ and α,α′‐hetero‐bifunctionalized poly(ε‐caprolactone)s by ring opening polymerization: The potentially valuable precursors for miktoarm star copolymers

Two new ring opening polymerization (ROP) initiators, namely, (3‐allyl‐2‐(allyloxy)phenyl)methanol and (3‐allyl‐2‐(prop‐2‐yn‐1‐yloxy)phenyl)methanol each containing two reactive functionalities viz. allyl, allyloxy and allyl, propargyloxy, respectively, were synthesized from 3‐allylsalicyaldehyde as a starting material. Well defined α‐allyl, α′‐allyloxy and α‐allyl, α′‐propargyloxy bifunctionalized poly(ε‐caprolactone)s with molecular weights in the range 4200–9500 and 3600–10,900 g/mol and molecular weight distributions in the range 1.16–1.18 and 1.15–1.16, respectively, were synthesized by ROP of ε‐caprolactone employing these initiators. The presence of α‐allyl, α′‐allyloxy and α‐allyl, α′‐propargyloxy functionalities on poly(ε‐caprolactone)s was confirmed by FT‐IR, ¹H, ¹³C NMR spectroscopy, and MALDI‐TOF analysis. The kinetic study of ROP of ε‐caprolactone with both the initiators revealed the pseudo first order kinetics with respect to ε‐caprolactone consumption and controlled behavior of polymerization reactions. The usefulness of α‐allyl, α′‐allyloxy functionalities on poly(ε‐caprolactone) was demonstrated by performing the thiol‐ene reaction with poly(ethylene glycol) thiol to obtain (mPEG)₂‐PCL miktoarm star copolymer. α‐Allyl, α′‐propargyloxy functionalities on poly(ε‐caprolactone) were utilized in orthogonal reactions i.e copper catalyzed alkyne‐azide click (CuAAC) with azido functionalized poly(N‐isopropylacrylamide) followed by thiol‐ene reaction with poly(ethylene glycol) thiol to synthesize PCL‐PNIPAAm‐mPEG miktoarm star terpolymer. The preliminary characterization of A₂B and ABC miktoarm star copolymers was carried out by ¹H NMR spectroscopy and gel permeation chromatography (GPC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 844–860     

Synthesis of Halogenated α,β‐Unsaturated γ‐Butyrolactone Derivatives by Triphenylphosphine‐Catalyzed Cyclization of α‐Halogeno Ketones with Dialkyl Acetylenedicarboxylates (=Dialkyl But‐2‐ynedioates)

A Ph₃P‐catalyzed cyclization of α‐halogeno ketones 2 with dialkyl acetylenedicarboxylates (=dialkyl but‐2‐ynedioates) 3 produced halogenated α,β‐unsaturated γ‐butyrolactone derivatives 4 in good yields (Scheme 1, Table). The presence of electron‐withdrawing groups such as halogen atoms at the α‐position of the ketones was necessary in this reaction. Cyclization of α‐chloro ketones resulted in higher yields than that of the corresponding α‐bromo ketones. Dihalogeno ketones similarly afforded the expected γ‐butyrolactone derivatives in high yields.     

Synthesis of β‐Haloketones by β‐Addition Reactions of α,β‐Unsaturated Ketones with BX3 (X = Br,Cl) as Halide Source

A series of β‐bromoketones and β‐chloroketones were synthesized by the addition reactions of α,β‐unsaturated ketones under BX₃ (X = Br, Cl) and ethylene glycol reaction system. The α,β‐unsaturated ester also was successfully converted to its corresponding β‐bromoester under the reaction condition.     

The Renaissance of α‐Methylene‐γ‐butyrolactones: New Synthetic Approaches

The amount of research activity concerning α‐methylene‐γ‐butyrolactones and α‐alkylidene‐γ‐butyrolactones has increased dramatically in recent years. This Review summarizes the structural types, biological activities, and biosynthesis of these compounds, concentrating on publications from the past 10 years. Traditional approaches to α‐methylene‐γ‐butyrolactones and α‐alkylidene‐γ‐butyrolactones are then reviewed together with novel approaches, including those from our own research group, reported more recently.     

Synthesis of Phenanthrene Derivatives through the Reaction of an α,α‐Dicyanoolefin with α,β‐Unsaturated Carbonyl Compounds

Phenanthrene derivatives were prepared by reacting an α,α‐dicyanoolefin with different α,β‐unsaturated carbonyl compounds resulting from Wittig reaction of ninhydrin and phosphanylidene or condensation of barbituric acid and an aldehyde. The easy procedure, mild and metal‐catalyst free, reaction conditions, good yields, and no need for chromatographic purifications are important features of this protocol. The structures of the product of type 3 and 5 were corroborated spectroscopically (IR, ¹H‐ and ¹³C‐NMR, and EI‐MS). A plausible mechanism for this type of reaction is proposed (Scheme 1).     

Comparison of Methionine α,γ‐Lyase and Homocysteine α,γ‐Lyase for Electrochemical Determination of Homocysteine

Recently, a novel enzymatic method was developed for determination of homocysteine. This method utilizes the electrochemical hydrogen sulfide sensor along with methionine α,γ‐lyase to accomplish the fast, accurate, sensitive and selective measurements. As a continuation of this work, another enzyme, homocysteine α,γ‐lyase, was used and the parallel experiments of using both enzymes were carried out against the effect of pH, sensitivity, linearity, and interferences, in an intended comparison between these two enzymes. The excellent linearity of amperometric currents against homocysteine concentrations, high sensitivities and low detection limits for both enzymes reconfirmed that the electrochemical method is superior over other analytical means. The high enzymatic activity of methionine α,γ‐lyase surpassing homocysteine α,γ‐lyase endowed the former higher sensitivity, lower detection limit and faster response than the latter, suggesting methionine α,γ‐lyase a better candidate for homocysteine measurement by electrochemical method. The differences between these two enzymes on the trends of response time and sensitivity at different pH environments, reactivity toward several forms of homocysteine as well as on the interference from several agents were also addressed and discussed.     

A Mild Isomerization Reaction for β,γ‐Unsaturated Ketone to α,β‐Unsaturated Ketone

A series of β,γ‐unsaturated ketones were isomerized to their corresponding α,β‐unsaturated ketones by the introduction of DABCO in iPrOH at room temperature. The endo‐cyclic double bond (β,γ‐position) on ketone was rearranged to exo‐cyclic double bond (α,β‐position) under the reaction conditions.     

Effect of annealing on the structure and properties of poly(vinylidene fluoride) β‐form films

Oriented poly(vinylidene fluoride) (PVDF) films consisting of β crystals were prepared by the solid‐state coextrusion (SC) of a gel film near the melting temperature (T_m) and by conventional cold tensile drawing (TD) of a melt‐quenched film. These films were annealed over the temperature range of 75–190 °C (below and above the static T_m) while the sample length was kept constant or constant loads were applied. After annealing with the sample length kept constant, the dynamic Young's modulus markedly decreased because of the relaxation of oriented amorphous chains, as shown by infrared spectroscopy. In contrast, annealing under a constant load improved the chain orientation in both the crystalline and amorphous regions, resulting in an increase in the modulus from an initial 10.5 to 14.3 GPa for the SC and from an initial 3.3 to 4.8 GPa for the TD. The SC, annealed at 190 °C with a constant load corresponding to an initial tension of 200 MPa, exhibited an extreme crystalline‐chain orientation of 0.998 and a modulus of 14.3 GPa, among the highest values ever reported for PVDF. Although the remanent polarization (P_r) of the TD increased slightly from the initial 62 to 68 mC/m², P_r of the SC stayed constant at 100 mC/m² independently of the annealing conditions. This suggests that the P_r value of 100 mC/m² approached the equilibrium value for this PVDF sample containing 3.5 mol % structural defects. Therefore, although the modulus and P_r of the TD increased slightly with annealing, the maximum values achieved by annealing were markedly lower than those of the SC and annealed SC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1701–1712, 2003     

Studies on the Mass Spectra of N‐Aryl α,β‐Unsaturated γ‐Lactams

The mass spectra of a series of N‐aryl α,β‐unsaturated γ‐lactams were studied. Besides the molecular ion, the three characteristic fragments such as [M⁺‐29], [M⁺‐55], and [M⁺‐82] were commonly found in a series of N‐Aryl α,β‐unsaturated γ‐lactams in EI/MS. Further more the mechanism for the interpretation of these fragments is also de scribed.     

Synthesis of new optically active α,α′,β‐trisubstituted‐β‐lactones as monomers for stereoregular biopolyesters

Various optically active (4R)‐alkyloxycarbonyl‐3,3‐dialkyl‐2‐oxetanones as monomers were synthesized from L‐(S)‐malic acid in six steps to prepare a new family of stereopolyesters for biomedical applications. The synthesis began with an esterification followed of a dialkylation in the aim to introduce hydrophobic groups as methyl or reactive group as allyl. Then, a saponification has permitted to obtain the corresponding diacids that reacted with appropriate alcohols to furnish different monoesters. The last and most important step was activation of hydroxyl group of monoesters with the asymmetric carbon configuration inversion according to the Mitsunobu reaction. Thus, this reaction has provided lactones from monoesters with 100% enantiomeric excess which was confirmed by ¹H NMR and by the synthesis of corresponding isotactic and semicrystalline homopolyesters. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2586–2597     

Synthesis and characterization of poly(higher‐α‐olefin)s with a nickel(α‐diimine)/methylaluminoxane catalyst system: Effect of chain running on the polymer properties

Homopolymerization of octadecene‐1 at different reaction conditions has been studied. Significant chain running can be seen at higher polymerization temperatures. Interestingly, insertion of octadecene‐1 into a sterically hindered nickel‐cation/carbon (secondary) bond is observed. The microstructure of the polymer was established using NMR spectroscopy. The effects of chain running on polymer melting, crystallization behavior, and dynamic mechanical thermal properties were studied using DSC and DMTA. The extent of chain running (i.e., 2,ω‐, 1,ω‐enchainments) decreases with an increase in the carbon number of α‐olefins. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 191–210, 2007     

Pendant groups fine‐tuning thermal gelation of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) aqueous solution

Novel poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) (PCL‐PEG‐PCL) bearing pendant hydrophobic γ‐(carbamic acid benzyl ester) groups (PECB) and hydrophiphilic amino groups (PECN) were synthesized based on the functionalized comonomer γ‐(carbamic acid benzyl ester)‐ε‐caprolactone (CABCL). The thermal gelation behavior of the amphiphilic copolymer aqueous solutions was examined. The phase transition behavior could be finely tuned via the pendant groups, and an abnormal phenomenon occurred that the sol–gel transition temperature shifted to a higher temperature for PECB whereas a lower temperature for PECN. The micelles percolation was adopted to clarify the hydrogel mechanism, and the effect of the pendant groups on the micellization was further investigated in detail. The results demonstrated that the introduction of γ‐(carbamic acid benzyl ester) pendant groups significantly decreased the crystallinity of the copolymer micelles whereas amino pendant groups made the micelles easy to aggregate. Thus, the thermal gelation of PEG/PCL aqueous solution could be finely tuned by the pendant groups, and the pendant groups modified PEG/PCL hydrogels are expected to have great potential biomedical application. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2571–2581     

Organocatalytic Enantioselective Synthesis of Tetrasubstituted α‐Amino Allenoates by Dearomative γ‐Addition of 2,3‐Disubstituted Indoles to β,γ‐Alkynyl‐α‐imino Esters

The first asymmetric synthesis of tetrasubstituted α‐amino allenoates by a chiral phosphoric acid catalyzed dearomative γ‐addition reaction of 2,3‐disubstituted indoles to β,γ‐alkynyl‐α‐imino esters is reported. This method provides access to a series of highly functionalized tetrasubstituted allenes featuring quaternary stereocenters in high yields, and with excellent regio‐, diastereo‐, and enantioselectivities under mild conditions without by‐product formation. Representative large‐scale reactions and diverse transformations of the products into various scaffolds with potential biological activities render are also disclosed. The mechanism of the reaction was elucidated by control reactions and DFT calculations.     

Preparation of novel poly(ethylene oxide‐co‐glycidol)‐graft‐poly(ε‐caprolactone) copolymers and inclusion complexation of the grafted chains with α‐cyclodextrin

A well‐defined comblike copolymer of poly(ethylene oxide‐co‐glycidol) [(poly(EO‐co‐Gly)] as the main chain and poly(ε‐caprolactone) (PCL) as the side chain was successfully prepared by the combination of anionic polymerization and ring‐opening polymerization. The glycidol was protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether (EPEE) first, and then ethylene oxide was copolymerized with EPEE by an anionic mechanism. The EPEE segments of the copolymer were deprotected by formic acid, and the glycidol segments of the copolymers were recovered after saponification. Poly(EO‐co‐Gly) with multihydroxyls was used further to initiate the ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate. When the grafted copolymer was mixed with α‐cyclodextrin, crystalline inclusion complexes (ICs) were formed, and the intermediate and final products, poly(ethylene oxide‐co‐glycidol)‐graft‐poly(ε‐caprolactone) and ICs, were characterized with gel permeation chromatography, NMR, differential scanning calorimetry, X‐ray diffraction, and thermogravimetric analysis in detail. The obtained ICs had a channel‐type crystalline structure, and the ratio of ε‐caprolactone units to α‐cyclodextrin for the ICs was higher than 1:1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3684–3691, 2006     

Supramolecular inclusion complexes of a star polymer containing cholesterol end‐capped poly(ε‐caprolactone) arms with β‐cyclodextrin

A novel hexa‐armed and star‐shaped polymer containing cholesterol end‐capped poly(ε‐caprolactone) arms emanating from a phosphazene core (N₃P₃‐(PCL‐Chol)₆) was synthesized by a combination of ring‐opening polymerization and “click” chemistry techniques. For this purpose, the terminal ? OH groups of the synthesized precursor (N₃P₃‐(PCL‐OH)₆) were converted into –Chol through a series of reaction. Both N₃P₃‐(PCL‐OH)₆ and N₃P₃‐(PCL‐Chol)₆ were then employed in the preparation of supramolecular inclusion complexes (ICs) with β‐cyclodextrin (β‐CD). The latter formed ICs with β‐CD in higher yield. The host–guest stoichiometry (ε‐CL:β‐CD, mol:mol) in the ICs of N₃P₃‐(PCL‐Chol)₆ was found to be 1.2. The formation of supramolecular ICs of N₃P₃‐(PCL‐Chol)₆ with β‐CD was confirmed by using Fourier transform infrared (FTIR) and ¹H nuclear magnetic resonance (NMR) spectroscopic methods, wide‐angle X‐ray diffraction (WAXD), and thermal analysis techniques. WAXD data showed that the obtained ICs with N₃P₃‐(PCL‐Chol)₆ had a channel‐type crystalline structure, indicating the suppression of the original crystallization of N₃P₃‐(PCL‐Chol)₆ in β‐CD cavities. Moreover, the thermal stabilities of ICs were found to be higher than those of the free star polymer and β‐CD. Furthermore, the surface properties of N₃P₃‐(PCL‐Chol)₆ and its ICs with β‐CD were investigated by static contact angle measurements. The obtained results proved that the wettability of N₃P₃‐(PCL‐Chol)₆ successfully increased with the formation of its ICs with β‐CD. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3406–3420