掺杂二氧化锡的二氧化钛的光学性质及其光催化特性

二氧化钛多相催化是一种极具前途的环境污染深度净化技术。 本文以钛酸四丁酯和四氯化锡为原料,无水乙醇为溶剂,采用溶胶-凝胶法制备了掺杂二氧化锡的二氧化钛薄膜和复合氧化物粉体。通过测量薄膜的吸收光谱推算光学能隙,结果发现掺杂样品的光学能隙比纯二氧化钛样品有所变小。随着热处理温度的提高,掺杂和纯二氧化钛样品的光学能隙都略微降低。X-射线衍射分析表明,复合氧化物粉体的热处理温度对样品的晶体结构和光催化性能有重要影响。以掺杂二氧化锡5 % 摩尔比的样品与纯二氧化钛对照,500 ℃以下热处理样品以锐钛矿结构为主,600 ℃热处理样品为锐钛矿与金红石相共存,并显示了较好的光催化性能。透射电子显微镜观察显示,同样600 ℃热处理,掺杂样品要比纯二氧化钛具有更小的颗粒尺寸。在700 ℃热处理的样品中,掺杂样品只存在金红石相而纯二氧化钛样品中仍存有锐钛矿相。用阿伦尼乌斯经验关系式推测的晶粒生长的活化能,纯二氧化钛47.486 kJ.mol, 掺杂5 % 摩尔比的复合氧化物样品33.103 kJ.mol。以亚甲基蓝为降解物质,考察了掺杂量和热处理温度对样品的光催化性能。     

Template‐free Fabrication of Hierarchical Macro‐/mesoporous N‐doped TiO2/graphene Oxide Composites with Enhanced Visible‐light Photocatalytic Activity

Hierarchical macro‐/mesoporous N‐doped TiO₂/graphene oxide (N‐TiO₂/GO) composites were prepared without using templates by the simple dropwise addition mixed solution of tetrabutyl titanate and ethanol containg graphene oxide (GO) to the ammonia solution, and then calcined at 350 °C. The as‐prepared samples were characterized by scanning electron microscopy (SEM), Brunauer‐Emmett‐Teller (BET) surface area, X‐ray diffraction (XRD), Raman spectroscopy, X‐ray photoelectron spectroscopy (XPS), and UV‐Vis absorption spectroscopy. The photocatalytic activity was evaluated by the photocatalytic degradation of methyl orange in an aqueous solution under visible‐light irradiation. The results show that N‐TiO₂/GO composites exhibited enhanced photocatalytic activity. GO content exhibited an obvious influence on photocatalytic performance, and the optimal GO addition content was 1 wt%. The enhanced photocatalytic activity could be attributed to the synergetic effects of three factors including the improved visible light absorption, the hierarchical macro‐mesoporous structure, and the efficient charge separation by GO.     

Photocatalytic Activity for Water Decomposition to Hydrogen over Nitrogen‐doped TiO2 Nanoparticle

Nitrogen-doped TiO2 nanoparticle photocatalysts were obtained by an annealing method with gaseous ammonia and nitrogen. The influence of dopant N on the crystal structure was characterized by XRD, XPS, BET, TEM and UV-Vis spectra. The results of XRD indicate that, the crystal phase transforms from anatase to rutile structure gradually with increase of annealing temperature from 300 to 700 ℃. XPS studies indicate that the nitrogen atom enters the TiO2 lattice and occupies the position of oxygen atom. Agglomeration of particles is found in TEM images after annealing. BET results show that the specific surface areas of N-doped samples from 44.61 to 38.27 m2/g are smaller than that of Degussa TiO2. UV-Vis spectra indicate that the absorption threshold shifts gradually with increase of annealing temperature, which shows absorption in the visible region. The influence of annealing condition on the photocatalytic property has been researched over water decomposition to hydrogen, indicating that nitrogen raises the photocatalytic activity for hydrogen evolution, and the modified TiO2 annealed for 2 h at 400 ℃ under gas of NH3/N2 (V/V＝1/2) mixture shows better efficiency of hydrogen evolution. Furthermore, the N-doped TiO2 nanoparticle catalysts have obvious visible light activity, evidenced by hydrogen evolution under visible light (λ＞400 nm) irradiation. However, the catalytic activity under visible light irradiation is absent for Degussa as reference and the N-doped TiO2 annealed at 700 ℃.     

Bulk and surface analysis of Ti1–xFexO2/Fe2O3 composites prepared by solid state reaction for photocatalytic applications

Ti_1–xFe_xO₂ / Fe₂O₃ (x = 0.3, 0.6, and 0.7 wt%) composites were prepared by solid state reaction of the oxides TiO₂ (rutile phase) and Fe₂O₃ at 550 °C. The following techniques were applied for the characterization of the composites: X‐ray powder diffraction, Mössbauer spectroscopy, SEM, energy dispersive X‐ray spectroscopy and adsorption of nitrogen. The anatase/rutile/hematite ratio and the abundance of Fe³⁺ were quantified. The results indicate that Fe³⁺ substituted Ti⁴⁺ in the rutile structure and that the α‐Fe₂O₃ phase was predominantly on the surface of the crystalline Ti_1–xFe_xO₂ powders. A substantial increase of the materials density, with respect to rutile, favoured the application of the composites in photocatalytic experiments. The performance of the solids upon the photodegradation of aqueous solutions of carbofuran was evaluated. The Lewis sites created in the composites correlated directly with the photodegradation rate constant of carbofuran and the decrease of the total organic carbon content in the treated solutions. Copyright © 2011 John Wiley & Sons, Ltd.     

Dye degradation studies of Mo‐doped TiO2 thin films developed by reactive sputtering

TiO₂ thin films with various Mo concentrations have been deposited on glass and n‐type silicon (100) substrates by this radio‐frequency (RF) reactive magnetron sputtering at 400°C substrate temperature. The crystal structure, surface morphology, composition, and elemental oxidation states of the films have been analyzed by using X‐ray diffraction, field emission scanning electron microscopy, atomic force microscopy, and X‐ray photoelectron spectroscopy, respectively. Ultraviolet‐visible spectroscopy has been used to investigate the degradation, transmittance, and absorption properties of doped and undoped TiO₂ films. The photocatalytic degradation activity of the films was evaluated by using methylene blue under a light intensity of 100 mW cm⁻². The X‐ray diffraction patterns show the presence of anatase phase of TiO₂ in the developed films. X‐ray photoelectron spectroscopy studies have confirmed that Mo is present only as Mo⁶⁺ ions in all films. The Mo/TiO₂ band gap decreases from ~3.3 to 3.1 eV with increasing Mo dopant concentrations. Dye degradation of ~60% is observed in Mo/TiO₂ samples, which is much higher than that of pure TiO₂.     

Photocatalytic properties of CuO/(001)‐TiO2 composites synthesized by the vapor–thermal method

Composites of (001)‐face‐exposed TiO₂ ((001)‐TiO₂) and CuO were synthesized in water vapor environment at 250°C with various Cu/Ti molar ratios (R_Cu/Ti). The resulting CuO/(001)‐TiO₂ composites were characterized using a variety of techniques. The synthesis under high‐temperature vapor allows close contact between CuO and (001)‐TiO₂, which results in the formation of heterojunctions, as evidenced by the shift of valence band maximum towards the forbidden band of TiO₂. An appropriate ratio of CuO can enhance the absorption of visible light and promote the separation of photogenerated carriers, which improve the photocatalytic performance. The degradation rate constant K_app increased from 5.5 × 10^?2 to 8.1 × 10^?2 min^?1 for R_Cu/Ti = 0.5. Additionally, the results showed that superoxide radicals (^?O₂^?) play a major role in the photocatalytic degradation of methylene blue.     

Effect of calcination temperature on the photocatalytic activity of carbon‐doped titanium dioxide revealed by photoluminescence study

Carbon‐doped titania (C‐TiO₂) nanoparticles were synthesized by the sol–gel method at different calcination temperatures (300–600°C) employing titanium tetraisopropoxide (TTIP) as the titanium source and polyoxyethylene sorbitan monooleate (Tween 80) as the carbon source. The physical properties of C‐TiO₂ samples were characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). The photocatalytic activities were checked through the photodegradation of phenolphthalein (PHP) under ultraviolet irradiation. The UV spectrum showed that the carbon doping extends the absorption range of TiO₂ to the visible region. However, the photocatalytic activity is affected by the electron–hole recombination phenomenon, as revealed by the photoluminescence (PL) study. According to the PL spectra, carbon doping reduces the edge‐to‐edge electron–hole recombination. Nevertheless, the number of defect sites is greatly influenced by the calcination temperature of C‐TiO₂. C‐TiO₂ that was calcined at 400°C showed the highest photodegradation percentage of PHP, which was mainly attributed to the synergic effect of the low direct edge‐to‐edge electron–hole recombination, high content of defect sites, and retention of active electrons on the surface hydroxyl group.     

Synthesis and Modification of Zn‐doped TiO2 Nanoparticles for the Photocatalytic Degradation of Tetracycline

The synthesis of Zn‐doped TiO₂ nanoparticles by solgel method was investigated in this study, as well as its modification by H₂O₂. The catalyst was characterized by transmission electron microscopy, X‐ray diffraction, Brunauer–Emmett–Teller, UV–visible reflectance spectra and X‐ray photoelectron spectroscopy (XPS). The results indicated that doping Zn into TiO₂ nanoparticles could inhibit the transformation from anatase phase to rutile phase. Zn existed as the second valence oxidation state in the Zn‐doped TiO₂. Zn‐doped TiO₂ that was synthesized by 5% Zn doping at 450°C exhibited the best photocatalytic activity. Then, the H₂O₂ modification further enhanced the photocatalytic activity. Zn doping and H₂O₂ modifying narrowed the band gap and efficiently increased the optical absorption in visible region. The optimal degradation rate of tetracycline by Zn‐doped TiO₂ and H₂O₂ modified Zn‐doped TiO₂ was 85.27% and 88.14%. Peroxide groups were detected in XPS analysis of H₂O₂ modified Zn‐doped TiO₂, favoring the adsorption of visible light. Furthermore, Zn‐doped TiO₂ modified by H₂O₂ had relatively good reusability, exhibiting a potential practical application for tetracycline's photocatalytic degradation.     

Synthesis and Photocatalytic Properties of Nano‐crystalline In2O3

A nano‐crystalline In₂O₃ was synthesized using calcinations methods and was used as a photocatalyst to degrade sulfan blue (SB) dye. In addition, this study addresses the conditions of the degradation and the factors that influenced the catalysis. In₂O₃ was prepared by calcining In(OH)₃ at heat ranges of 100–700 °C for 24 h. The In₂O₃ was characterized using field emission scanning electron microscopy (FE‐SEM), an X‐ray diffractometer (XRD), thermogravimetric analysis (TGA), and high‐resolution X‐ray photoelectron spectroscopy (HR‐XPS). The activities of these samples were tested for the photocatalytic degradation of SB dye. The results indicated that the In(OH)₃ that was calcined at 300 °C for 24 h had the best performance.     

Investigations on the Phase Transformation,Optical Characteristics,and Photocatalytic Activity of Synthesized Heterostructured Nanoporous Bi2O3–TiO2

Fine‐powdered, heterostructured, nanoporous Bi₂O₃–TiO₂ (BTO) was synthesized by a green approach using ultrasonication, with the mole ratio Bi/Ti of 1:1 and calcined at different temperatures. The physical and optical properties of the mixed oxides were investigated. The phase structure, as identified by X‐ray diffraction (XRD), showed the appearance of new phases as a function of the calcination temperature. Morphological examinations indicated the formation of a nanoporous structure with a drastic change in morphology at the calcination temperature of 850°C from a globule to a rod‐shaped structure, which further got transformed to a rocky appearance at 1200°C. Doping with Bi₂O₃ led to the lowering of the bandgap of TiO₂ from 3.25 to 2.5 eV. A BTO nanocatalyst calcined at 450°C exhibited promising photocatalytic activity for the degradation of quinalphos (QP) (92%) after a time interval of 100 min under visible light and at the optimum pH 8. The kinetics of degradation of QP showed that it follows a pseudo‐first‐order path with a rate constant 0.01267 min^?1. The synthesized BTO mixed oxide showed profound improvement in photocatalytic activity in the visible region as compared to TiO₂.     

The effect of annealing temperatures on surface properties,hydroxyapatite growth and cell behaviors of TiO2 nanotubes

Well‐ordered TiO₂ nanotubes were prepared by the electrochemical anodization of titanium in an ethylene glycol electrolyte containing 1 wt% NH₄F and 10 wt% H₂O at 20 V for 20 min, followed by annealing. The surface morphology and crystal structure of the samples were examined as a function of the annealing temperature by field emission scanning electron microscopy (FE‐SEM) and X‐ray diffraction (XRD), respectively. Crystallization of the nanotubes to the anatase phase occurred at 450 °C, while rutile formation was observed at 600 °C. Disintegration of the nanotubes was observed at 600 °C and the structure vanished completely at 750 °C. Electrochemical corrosion studies showed that the annealed nanotubes exhibited higher corrosion resistance than the as‐formed nanotubes. The growth of hydroxyapatite on the different TiO₂ nanotubes was also investigated by soaking them in simulated body fluid (SBF). The results indicated that the tubes annealed to a mixture of anatase and rutile was clearly more efficient than that in their amorphous or plain anatase state. The in vitro cell response in terms of cell morphology and proliferation was evaluated using osteoblast cells. The highest cell activity was observed on the TiO₂ nanotubes annealed at 600 °C. Copyright © 2010 John Wiley & Sons, Ltd.     

Photocatalytic Activity of TiO2 Nanofibers with Doped La Prepared by Electrospinning Method

La‐TiO₂ nanofibers are prepared by a sol‐gel assisted electrospinning method. The structure and morphology of La‐TiO₂ nanofibers are characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). XRD analysis shows that the weight percentage of anatase and rutile in the 1.5 mol% La‐TiO₂ nanofibers calcined at 600 °C is about 8:2, which is similar to P‐25. The XRD data of La‐TiO₂ nanofibers with different La content shows that La³⁺ dopant has a great inhibition on TiO₂ phase transformation. The photocatalytic activity of the as‐prepared La‐TiO₂ nanofibers is evaluated by photocatalytic decolorization of Methylene Blue (MB) aqueous solution. The results show that the 1.5 mol% La‐TiO₂ nanofibers calcined at 600 °C exhibit high photocatalytic activity, indicating that 600 °C and 1.5 mol% are the appropriate calcination temperature and optimal molar ratio of La to Ti, respectively.     

Photocatalytic Degradation of Organic Reactive Dyes over MnTiO3/TiO2 Heterojunction Composites Under UV‐Visible Irradiation

In this study, the photocatalytic degradation of organic reactive dyes have been investigated using MnTiO₃/TiO₂ heterojunction composites in the presence of electron acceptors under UV‐Visible light irradiation. This MnTiO₃/TiO₂ heterojunction composites were prepared by annealing different mass ratios of pyrophanite MnTiO₃ (3–11 wt%) and TiO₂ at 300°C. All the MnTiO₃/TiO₂ heterojunction composites were characterized by spectral techniques like X‐ray diffraction (XRD), scanning electron microscope (SEM) and diffused reflectance UV‐visible spectroscopic analysis (DRS). Among them, 9 wt% MnTiO₃/TiO₂ heterojunction composites exhibited higher photocatalytic activity for the degradation of Reactive Blue 4 (RB 4). The photocatalytic efficiency of 9 wt% MnTiO₃/TiO₂ heterojunction composites was further enhanced by the addition of substantial amount of electron acceptors like hydrogen peroxide (H₂O₂) and ammonium peroxydisulfate ([NH₄]₂S₂O₈). The presence of oxidants (electron acceptors) facilitates the fast degradation of dye solution even in higher concentration upto 200 mg/L. The photocatalytic activity of MnTiO₃/TiO₂ heterojunction composites was also studied for the degradation of other four different structured reactive dyes. The extent of mineralization of these organic reactive dyes during photocatalytic degradation was estimated from COD analysis. MnTiO₃/TiO₂ heterojunction composites was also found to have good photostability in the presence of oxidants.     

High‐temperature oxidation behavior of Ni‐based superalloys with Nb and Y and the interface characteristics of oxidation scales

Ni‐based superalloys with niobium (Nb) or/and yttrium (Y) were prepared by vacuum melting. The oxidation kinetics of these alloys was studied by thermogravimetry at 800 °C for 100 h in static air. Morphology of oxides was studied using SEM, and the composition was analyzed by X‐ray diffraction. Energy‐dispersive X‐ray spectrometer was employed to examine the linear element distribution of the cross section of the oxidation films. Results showed that the oxidation kinetics all followed a parabolic law at different stages. The oxide films were mainly comprised of Cr₂O₃, NiCr₂O₄, Al₂O₃ and TiO₂. All the oxide films exhibited layered structure owing to different oxidation stages. With the addition of Nb or Y, the high‐temperature oxidation resistance of the superalloy was improved significantly and the surface morphology of the oxidation film was ameliorated. The comprehensive effect of Nb and Y was remarkable in improving the high‐temperature oxidation resistance of Ni‐based alloys. Copyright © 2014 John Wiley & Sons, Ltd.     

Monitoring the Structure Evolution of Titanium Oxide Photocatalysts: From the Molecular Form via the Amorphous State to the Crystalline Phase

Amorphous Ti_xO_y with high surface area has attracted significant interest as photocatalyst with higher activity in ultraviolet (UV) light-induced water splitting applications compared to commercial nanocrystalline TiO₂. Under photocatalytic operation conditions, the structure of the molecular titanium alkoxide precursor rearranges upon hydrolysis and leads to higher connectivity of the structure-building units. Structurally ordered domains with sizes smaller than 7 Å form larger aggregates. The experimental scattering data can be explained best with a structure model consisting of an anatase-like core and a distorted shell. Upon exposure to UV light, the white Ti_xO_y suspension turns dark corresponding to the reduction of Ti⁴⁺ to Ti³⁺ as confirmed by electron energy loss spectroscopy (EELS). Heat-induced crystallisation was followed by in situ temperature-dependent total scattering experiments. First, ordering in the Ti−O environment takes place upon to 350 °C. Above this temperature, the distorted anatase core starts to grow but the structure obtained at 400 °C is still not fully ordered.     

Influence of thermal annealing on the microstructure,hardness and corrosion behavior of TiAlSiCuN nanocomposite films

Nanocomposite TiAlSiCuN films were deposited on high speed steels by filtered magnetic arc ion plating. Detailed properties of the films annealed at various temperatures are studied. After thermal annealing at different temperatures ranging from 400 to 800 °C, changes in the film micro‐structure, chemical and phase composition, surface morphology, hardness and polarization curve properties were systematically characterized by X‐ray diffraction, X‐ray photoelectron spectroscopy, scanning electron microscopy, nano‐indenter and electrochemical workstation, respectively. It was found that the TiAlSiCuN films could be fully oxidized at 800 °C, Al and Ti atoms all diffused outwards and formed dense protective Al₂O₃ and TiO₂ layer. Simultaneously, the TiAlN phase gradually disappeared. The films annealed at 400 °C obtained the highest hardness because of the certain grain growth and little generated oxides. Besides, the certain formation of dense protective Al₂O₃ layer made the TiAlSiCuN film annealed at 600 °C present the least corrosion current density and the corrosion voltage. Copyright © 2016 John Wiley & Sons, Ltd.     

Substrate temperature effects on the structural,compositional, and electrical properties of VO2 thin films deposited by pulsed laser deposition

The vanadium dioxide (VO₂) thin films were deposited on silicon (100) substrate using the pulsed laser deposition technique. The thin films were deposited at different substrate temperatures (500°C, 600°C, 700°C, and 800°C) while keeping all the other parameters constant. X‐ray diffraction confirmed the crystalline VO₂ (B) and VO₂ (M) phase formation at different substrate temperatures. X‐ray photoelectron spectroscopy analysis showed the presence of V⁴⁺ and V⁵⁺ charge states in all the deposited thin films which confirms that the deposited films mainly consist of VO₂ and V₂O₅. An increase in the VO₂/V₂O₅ ratio has been observed in the films deposited at higher substrate temperatures (700°C and 800°C). Scanning electron microscope micrographs revealed different surface morphologies of the thin films deposited at different substrate temperatures. The electrical properties showed the sharp semiconductor to metal transition behavior with approximately 2 orders of magnitude for the VO₂ thin film deposited at 800°C. The transition temperature for heating and cooling cycles as low as 46.2°C and 42°C, respectively, has been observed which is related to the smaller difference in the interplanar spacing between the as‐deposited thin film and the standard rutile VO₂ as well as to the lattice strain of approximately −1.2%.     

Hydrothermal oxidation synthesis of rod‐like ZnO and the influence of oxygen vacancy on photocatalysis

Rod‐like ZnO nanoparticles (NPs ) were synthesized from zinc powder by a simple hydrothermal oxidation method. The presence of acetylacetone could promote the oxidation reaction of Zn and the formation of hexagonal nanorods. Then, the as‐prepared samples were annealed in N₂ , O₂ , and air atmosphere at 550°C for 2 h to control the number of oxygen vacancies in the samples. The samples were characterized by X‐ray diffraction, scanning electron microscopy, X‐ray photoelectron spectroscopy, and UV –vis spectroscopy. The correlation between the oxygen vacancies and the photocatalytic activity was investigated. The results reveal that the annealing process alters the samples’ bandgap and number of the oxygen vacancies, thereby improving the photocatalytic activity. The enhancement of photodegradation efficiency arising from the appropriate content of oxygen vacancies is discussed.     

Synthesis of TiO2 (B) and High‐temperature Stable Anatase TiO2 Nanowires by Hydrothermal Method and Investigation of Photocatalytic Activity

In this study, TiO₂ nanowires (TNWs) were synthesized through hydrothermal method and were characterized using X‐Ray diffraction (XRD), transmission electron microscopy (TEM) and BET techniques. Monoclinic TiO₂ (B) is the dominant phase of TNWs up to 600°C which is completely transformed into a highly crystalline anatase phase at 800°C. The photocatalytic activity of TNWs, prepared at various calcination temperatures, was investigated in the removal of Rhodamine B as an organic model pollutant. The results indicated that the photocatalytic activity of TNWs, prepared at 800°C calcination temperature, was better than that of other samples and even TiO₂–P25 nanoparticles.     

The structural, morphological, and surface properties of tungsten-doped TiO2 nanopowders and their contribution to the photocatalytic activity

Tungsten-doped TiO₂ nanopowders (W-TiO₂) were prepared by chemical vapor synthesis and the effects of a post-heat treatment on their physical, surface, and photocatalytic properties were investigated. The W-TiO₂ nanopowders containing about 1.0 mol % of tungsten were obtained and annealed from 400 to 700 °C. The as-synthesized and annealed W-TiO₂ nanopowders were carefully examined for their crystalline and opto-electronic structure and morphology by means of X-ray diffraction, UV–Vis spectroscopy, and transmission electron microscopy. In addition, the surface condition was investigated by X-ray photoelectron spectroscopy. The photocatalytic activities were studied by the oxidative degradation of 2-propanol under UV light irradiation. We found that the photocatalytic activity of W-TiO₂ varied significantly with the temperature of the heat treatment, exceeding the performance of P25 after annealing at 600 °C. Interestingly, the chemical composition of titanium and tungsten of W-TiO₂ played a crucial role to its photocatalytic activity as the mixed valence states, Ti ⁿ⁺ (n = 4, 3, 2, 0) and W ⁿ⁺ (n = 6, 5, 4), were found in accordance with altering the annealing temperature.