Synthesis and characterization of UV‐curable phosphorus containing hybrid materials prepared by sol–gel technique

In this study, a series of ultraviolet (UV)‐curable organic–inorganic hybrid coating materials containing phosphorus were prepared by sol–gel approach from acrylate end‐capped urethane resin, acrylated phenyl phosphine oxide oligomer (APPO), and inorganic precursors. TEOS and MAPTMS were used to obtain the silica network and Ti:acac complex was employed for the formation of the titania network in the hybrid coating systems. Coating performance of the hybrid coating materials applied on aluminum substrates was determined by the analysis techniques, such as hardness, gloss, impact strength, cross‐cut adhesion, taber abrasion resistance, which were accepted by international organization. Also, stress–strain test of the hybrids was carried out on the free films. These measurements showed that all the properties of the hybrids were enhanced effectively by gradual increase in sol–gel precursors and APPO oligomer content. The thermal behavior of the hybrid coatings was investigated by thermogravimetric analysis (TGA) analysis. The flame retardancy of the hybrid materials was examined by the limiting oxygen index (LOI); the LOI values of pure organic coating (BF) increased from 31 to 44 for the hybrid materials containing phosphorus (BF‐P:40/Si:10). The data from thermal analysis and LOI showed that the hybrid coating materials containing phosphorus have higher thermal stability and flame resistance properties than the organic polymer. Besides that, it was found that the double bond conversion values for the hybrid mixtures were adequate in order to form an organic matrix. The polycondensation reactions of TEOS and MAPTMS compounds were also investigated by ²⁹Si‐NMR spectroscopy. SEM studies of the hybrid coatings showed that silica/titania particles were homogenously dispersed through the organic matrix. In addition, it was determined that the hybrid material containing phosphorus and silica showed fibrillar structure. Copyright © 2009 John Wiley & Sons, Ltd.     

Selective Hg2+ sensor performance based various carbon‐nanofillers into CuO‐PMMA nanocomposites

Ternary nanocomposites (NCs) containing copper oxide (CuO)/poly(methyl methacrylate)/various carbon‐based nanofillers have been successfully prepared as thin films by an ex situ method as a selective Hg⁺² sensor. The structural, morphological, and electrochemical properties of the NCs were identified by all common characterization tools. The FT‐IR curves of these NCs proved the efficiency of CuO mixed with single‐walled CNTs (CuO/SWCNTs), multi‐walled CNTs (CuO/MWCNTs), or graphene (CuO/G) nanoparticles in the PMMA polymer matrix. The mixed nanofillers significantly improved the properties of the PMMA film. The thermal characteristics of the pure PMMA polymer matrix were highly developed by adding nanofillers in the form of NCs. The maximum composite degradation temperature (CDT_max) values were comparable for all the NCs and were in the range of 345 to 406°C. For fabrication, the CuO‐PMMA‐SWCNT, CuO‐PMMA‐MWCNT, and CuO‐PMMA‐GNCs were coated onto a glassy carbon electrode (GCE) to form a tiny layer with orderly thickness using a conductive 5% Nafion chemical binder. During the electrochemical investigation, it was found that CuO‐PMMA‐SWCNT had the maximum response toward Hg²⁺ ions compared to the other nanofillers in a buffer medium (phosphate type). To calibrate the Hg²⁺ ionic sensor, the data were plotted against Hg²⁺ ion concentration and the proposed sensor showed linearity over a wide range of concentrations (0.1‐0.01 mM), which is called the linear dynamic range (LDR). The analytical parameters, such as sensitivity (1.70 × 102 μAμM^‐1 cm^?2), detection limit (55.76 ± 2.79 pM), and limit of quantification (185.87 pM) were calculated from the calibration curve. Moreover, it showed good reproducibility, fast response time, good linearity, large LDR, and good stability. The CuO‐PMMA‐SWCNT NC‐modified GCE offers a new route to fabricate novel heavy metal ionic sensors, which might be used in green environment and health development applications.     

Improving Thermal and Flame Retardant Properties of Epoxy Resin with Organic NiFe‐Layered Double Hydroxide‐Carbon Nanotubes Hybrids

To improve the dispersion of carbon nanotubes (CNTs) and flame retardancy of layered double hydroxide (LDH) in epoxy resin (EP), organic nickel‐iron layered double hydroxide (ONiFe‐LDH‐CNTs) hybrids were assembled through co‐precipitation. These hybrids were further used as reinforcing filler in EP. EP/ONiFe‐LDH‐CNTs nanocomposites containing 4 wt% of ONiFe‐LDH‐CNTs with different ratios of ONiFe‐LDH and CNTs were prepared by ultrasonic dispersion and program temperature curing. The structure and morphology of the obtained hybrids were characterized by different techniques. The dispersion of nanofillers in the EP matrix was observed by transmission electron microscopy (TEM). The results revealed a coexistence of exfoliated and intercalated ONiFe‐LDH‐ CNTs in polymer matrix. Strong combination of the above nanofillers with the EP matrix provided an efficient thermal and flame retardant improvement for the nanocomposites. It showed that EP/ONiFe‐LDH‐CNTs nanocomposites exhibited superior flame retardant and thermal properties compared with EP. Such improved thermal properties could be attributed to the better homogeneous dispersion, stronger interfacial interaction, excellent charring performance of ONiFe‐LDH and synergistic effect between ONiFe‐LDH and CNTs.     

Thermomechanical Properties of Carbon Nanocomposites PEGDA Photopolymers

In this work, UV-curable resin poly (ethylene glycol) diacrylate (PEGDA) was reinforced with three different types of nanofillers: pristine graphene (G), multiwalled carbon nanotubes (MWNTs), and a hybrid of MWNTs and graphene 70/30 in mass ratio (Hyb). PEGDA was mixed homogenously with the nanofiller oligomer by shear mixing and then photopolymerized, affording thin, stable films. The thermomechanical properties of the afforded nanocomposites indicated the superior reinforcing ability of pristine graphene compared with MWNTs and an intermediate behavior of the hybrid.     

Elastomer Nanocomposite; Properties

Polymer nanocomposites represent a class of materials that have assumed great importance in recent years and are the focus of extensive research. Unlike plastomer nanocomposites, the elastomer nanocomposites are in the stage of infancy in respect to their applications.

In general, in polymer composites, the matrix and the filler are bonded to each other by weak intermolecular forces and covalent bonding are rarely involved. If the filler could be dispersed in the polymer matrix at the nanometre level and is able to interact with the matrix by chemical bonding, nanocomposites with significant properties improvement are obtained. These improvements can include mechanical properties (module, strength, etc.), thermal resistance, decrease in gas permeability (barrier), flammability, etc.

This paper is a review of the property improvements of different elastomers using nanofillers like silicates, carbon black, metallic powders, cellulose crystals, mixture of nanofillers, etc, with the intention of obtaining elastomer nanocomposites.     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

One‐pot synthesis of (3‐sulfopropyl methacrylate potassium)‐silica hybrid monolith via thiol‐ene click chemistry for CEC

A novel (3‐sulfopropyl methacrylate potassium)‐silica hybrid monolithic column for CEC has been prepared by a simple one‐pot approach based on efficient thiol‐ene click chemistry. In this process, the polycondensation of hydrolyzed alkoxysilanes and in situ click reaction of vinyl groups on 3‐sulfopropyl methacrylate potassium and thiol groups on the precondensed siloxanes simultaneously occurred in a pretreated capillary. Homogeneous monolithic matrix with large through‐pores tightly bonded to the inner wall of the capillary was shown by optical microscope and SEM. The minimum plate height of this hybrid monolithic column was determined as 3.9 μm for thiourea. Anilines, alkylbenzenes, and phenols were well separated on this hybrid monolithic column by CEC, which indicated typical reversed‐phase and cation‐exchange chromatographic retention mechanisms of the column.     

Influence of silica nanoparticles combined with zinc phosphinate on flame retardant properties of PET

Zinc phosphinate (Exolit OP950), nanosilica particles and polyethylene terephthalate (PET) have been blended and thereafter melt‐spinned to develop a new flame retardant (FR) system for PET textiles. The effects of the two types of nanosilica fillers on the wettability, dispersibility and thermal properties were studied to determine how the degree of hydrophilicity affects the PET matrix. The influence of the blends on thermal transitions has been investigated by differential scanning calorimetry (DSC), the thermal stability of the polymer/FR blend composites has been assessed by thermogravimetric analysis (TGA) and cone calorimetry has been used to study the fire reaction. It was noticed that the nanoparticles have a limited influence on the thermal transitions of the PET matrix, but zinc phosphinate acted as a plasticizer and a compatibilizer for the more hydrophobic particles. Thermogravimetric analysis results showed that the addition of silica particles and FR compound improves slightly the thermal stability of the PET systems under nitrogen and air atmospheres. Furthermore, it was noticed that the incorporation of nanoparticles gives almost no improvement in the PET fire reaction from cone calorimeter experiments. However, in the presence of Exolit OP950, the systems acted as FR in PET films and knitted structures. The heat release rate during the combustion decreased, and the thermal behaviors of these structures were closed to those with 10% wt of Exolit OP950. Copyright © 2017 John Wiley & Sons, Ltd.     

Phenylboronate‐diol crosslinked polymer/SWCNT hybrid gels with reversible sol–gel transition

This work demonstrates the successful incorporation of functionalized single‐walled carbon nanotubes (f‐SWCNTs) into the phenylboronate‐diol crosslinked polymer gel to create a hybrid system with reversible sol–gel transition. The phenylboronic acid‐containing and diol‐containing polymers were first separately prepared by the reversible addition–fragmentation chain transfer polymerization. Covalent functionalization of single‐walled carbon nanotubes (SWCNTs) with an azide‐derivatized, diol‐containing polymer was then accomplished by a nitrene addition reaction. Subsequently, the hybrid gels were prepared by crosslinking the mixture of f‐SWCNTs and diol‐containing polymer with the phenylboronic acid‐containing polymer. The hybrid gel has been characterized by scanning electron microscopy (SEM) and rheological analysis. The SEM measurement demonstrated a homogeneous dispersion of f‐SWCNTs within the gel matrices. Rheological experiments also demonstrated that the hybrid gel exhibited storage moduli significantly higher than those of the native gel obtained from the phenylboronic acid‐containing and diol‐containing polymers. The hybrid gel can be switched into their starting polymer (f‐SWCNTs) solutions by adjusting the pH of the system. Moreover, the hybrid gel revealed a self‐healing property that occurred autonomously without any outside intervention. By employing this dynamic character, it is possible to regenerate the used gel, and thus, it has the potential to perform in a range of dynamic or bioresponsive applications Copyright © 2013 John Wiley & Sons, Ltd.     

Interfacial interaction in EVA‐carbon nanotube and EVA‐clay nanocomposites

Proper filler‐matrix compatibility is a key factor in view of obtaining nanocomposites with well‐dispersed nanofillers displaying enhanced properties. In this respect, polymer‐filler interaction can be improved by a proper combination of matrix and nanofiller polarities. This is explored for matrices ranging from nonpolar high density poly(ethylene) to ethylene‐vinyl acetate (EVA) copolymers with varying vinyl acetate contents, in combination with several types of organoclay or carbon nanotubes. A novel in situ characterization methodology using modulated temperature differential scanning calorimetry is presented to evaluate the matrix‐filler interaction. During quasi‐isothermal crystallization of the matrix, an “excess” contribution is observed in the recorded heat capacity signal because of reversible melting and crystallization. Its magnitude considerably decreases upon addition of nanofiller in case of strong interfacial interaction, whereas the influence is moderate in case of a less interacting matrix‐filler combination. It is suggested that the “excess heat capacity” can be used to quantify the segmental mobility of polymer chains in the vicinity of the nanofiller. Hence it provides valuable information on the strength of interaction, governed by the physical and chemical nature of matrix and filler. Heating experiments subsequent to quasi‐isothermal crystallization point at a certain degree of molecular ordering, responsible for crystal nucleation in EVA copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1291–1302, 2007     

Non‐surfactant template‐directed synthesis of SiO2‐polyimide hybrid self‐standing films with ordered mesoporous structure

The silica‐PI hybrid self‐standing films with ordered mesoporous structure have been prepared by using dibenzoyl‐L ‐tartaric acid (L ‐DBTA) as non‐surfactant template under mild sol–gel route. Polyimide matrix was obtained from polyamic acid (PAA) via thermal imidization process and the template was removed in this process. The PI‐based hybrid film with 20 wt% SiO₂ obtained from DBTA presented the ordered mesoporous channels with average pore size of about 2.0 nm and BET surface area of 1167 m²/g. FTIR and SEM studies indicated that the hydrogen bond interaction between the carboxylic groups of DBTA and benzamide bonds of PAA made the PAA possibly participate in the assembly process of the aggregates of the non‐surfactant template molecules. The mechanical, thermal and some physical properties of these hybrid films materials were also characterized. Copyright © 2010 John Wiley & Sons, Ltd.     

A 3D Nanostructured Hydrogel‐Framework‐Derived High‐Performance Composite Polymer Lithium‐Ion Electrolyte

Solid‐state electrolytes have emerged as a promising alternative to existing liquid electrolytes for next generation Li‐ion batteries for better safety and stability. Of various types of solid electrolytes, composite polymer electrolytes exhibit acceptable Li‐ion conductivity due to the interaction between nanofillers and polymer. Nevertheless, the agglomeration of nanofillers at high concentration has been a major obstacle for improving Li‐ion conductivity. In this study, we designed a three‐dimensional (3D) nanostructured hydrogel‐derived Li_0.35La_0.55TiO₃ (LLTO) framework, which was used as a 3D nanofiller for high‐performance composite polymer Li‐ion electrolyte. The systematic percolation study revealed that the pre‐percolating structure of LLTO framework improved Li‐ion conductivity to 8.8×10^?5 S cm^?1 at room temperature.     

Luminescent lanthanide molecular‐based hybrid materials bridged through novel urethane linkages

Novel organosilicates with covalently linked functional modified aromatic acid have been synthesized from 3‐aminopropyl triethoxysilane (APS) grafted 4‐ethoxy benzoic acid (EB‐Si) and terbium ions via a simple low‐temperature route. The existence of covalent bonds between EB‐Si and silica matrices was shown by the hydrolysis and polycondensation processes of ethoxysilyl groups. Luminescence spectra were used to characterize the photophysical properties of the obtained hybrid material and the above spectroscopic data reveal that the triplet energy of modified para ethoxy benzoic acid in this favorable hybrid system matches the emissive energy level of RE³⁺. Copyright © 2006 John Wiley & Sons, Ltd.     

Synergistic effect of double percolated co‐supportive MWCNT‐CB conductive network for high‐performance EMI shielding application

The recent development in telecommunication technology has led electromagnetic interference (EMI) to a serious threat to both electronic devices and living beings. In this work, we designed a highly efficient EMI shielding material by taking advantage of both carbonaceous hybrid filler and double percolation phenomenon. Here, a flexible, lightweight microwave absorbing conductive polymer composite was fabricated by employing poly (ethylene‐co‐methyl acrylate) and ethylene octene copolymer (EMA/EOC) binary blend as the matrix and multiwall carbon nanotube carbon black (MWCNT/CB) hybrid filler as the conductive moiety. We investigated the effect of MWCNT content in the hybrid composite on mechanical, thermomechanical, electrical, and shielding efficiency. A total EMI shielding efficiency of ?37.4 dB in the X band region was attained with 20 wt% hybrid filler containing 50 wt% MWCNT along with promising mechanical properties.     

Poly(ethylene terephthalate) copolymers containing 5‐tert‐butyl isophthalic units

Poly(ethylene terephthalate‐co‐5‐tert‐butyl isophthalate) copolymers, abbreviated as PET^tBI, with compositions ranging between 95/5 and 25/75, as well as the two parent homopolymers, PET and PE^tBI, were prepared from comonomer mixtures by a two‐step melt‐polycondensation. Polymer intrinsic viscosities varied from 0.4 to 0.7 dL g^?1 with weight‐average molecular weights ranging between 31,000 and 80,000. The copolymers were found to have a random microstructure with a composition according to that used in the corresponding feed. The melting temperature and crystallinity of PET^tBI decreased with the content in 5‐tert‐butyl isophthalic units, whereas the glass‐transition temperature increased from 82 °C for PET up to 99 °C for PE^tBI. Copolymerization slightly improved the thermal stability of PET. Preliminary X‐ray diffraction studies revealed that PET^tBI adopt the same crystal structure as PET with the alkylated isophthalic units probably excluded from the crystal lattice. The homopolymer PE^tBI appeared to be a highly crystalline polymer taking up a crystal structure clearly different from that of PET and PET^tBI copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 1994–2004, 2001     

Structural characterization of silica modified polyimide membranes

Polyimide and hybrid polyimide‐siloxane were synthesized by polycondensation, imidization, and sol‐gel reaction. The polyimides were prepared from pyromellitic dianhydride (PMDA) and 4,4‐oxydianiline (ODA) in N‐methyl‐2‐pyrollidone (NMP). Trimethoxyvinyl silane (TMVS) was used as a source of silica. Their surface morphologies, structures and thermal performances were determined using scanning electron microscopy (SEM), infrared spectroscopy (IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results showed that the silica particles were finely and rather homogeneously dispersed in polymers. The glass transition temperature (T_g) of hybrid membrane materials increased with the increasing silica content. TGA analysis showed that polyimides were thermally stable with silica. Modified polyimide‐siloxane films, thermal characteristics were found to be better than the polyimide films without silica. Copyright © 2006 John Wiley & Sons, Ltd.     

Preparation and characterization of novel negatively charged hybrid membranes

Charged hybrid membranes with anionic‐ or cationic‐exchange groups have attracted increasing interest due to their higher thermal stabilities and structural flexibilities which are considered suitable for use in some harsh conditions, such as higher temperature and strongly oxidizing circumstances, for industrial applications. To develop new routes to synthesize the negatively charged hybrid membranes, a series of hybrid membranes were prepared via free radical polymerization of glycidylmethacrylate (GMA) and γ‐methacryloxypropyl trimethoxy silane (MPTMS) monomers, and ring‐opening of epoxide to create negatively charged ? SO₃H groups in the polymer chains. The fundamental properties of these prepared membranes were characterized through TGA, ion‐change capacity (IEC), and MALDI–TOF mass spectra. TGA showed that the thermal degradation temperature of these membranes could reach up to 300°C and the temperature of the first endothermic peak decreased with an increase in the content of ? SO₃H groups. IEC measurements showed that their IECs were within the range of 0.22–0.35 mmol g^?1. MALDI–TOF spectrometry indicated that the incorporation of GMA into the hybrid matrix could improve the structural stability of the membranes. These findings demonstrated that the ion‐exchange properties and structural stability of negatively charged hybrid membranes can be conveniently controlled by adjusting the GMA moiety in the hybrid matrix. Copyright © 2009 John Wiley & Sons, Ltd.     

Melt‐crystallization mechanism of poly(ethylene terephthalate)/multi‐walled carbon nanotubes prepared by in situ polymerization

A series of poly(ethylene terephthalate)/multi‐walled carbon nanotubes (PET/MWCNTs) nanocomposites were prepared by in situ polymerization using different amounts of multi‐walled carbon nanotubes (MWCNTs). The polymerization of poly(ethylene terephthalate) (PET) was carried out by the two‐stage melt polycondensation method. The intrinsic viscosity (IV) of the composites is ranged between 0.31 and 0.63 dL/g depending on the concentration of the MWCNTs. A decrease of IV was found by increasing MWCNTs content. This is due to the reactions taking place between the two components leading to branched and crosslinked macromolecules. These reactions are, mainly, responsible for thermal behavior of nanocomposites. The melting point of the nanocomposites was shifted to slightly higher temperatures by the addition till 0.55 wt % of MWCNTs while for higher concentration was reduced. The degree of crystallinity in all nanocomposites was, also, reduced by increasing MWCNTs amount. However, from crystallization temperature, it was found that MWCNTs till 1 wt % can enhance the crystallization rate of PET, whereas at higher content (2 wt %), the trend is the opposite due to the formation of crosslinked macromolecules. From the extended crystallization analysis, it was proved that MWCNTs act as nucleating agents for PET crystallization. Additionally, the crystallization mechanism due to the existence of MWCNT becomes more complicated because two mechanisms with different activation energies are taking place in the different degrees of crystallization, depending on the percentage of MWCNT. The effect of molecular weight also plays an important role. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1452–1466, 2009     

Thermal Properties and Crystallinity of Thermotropic Liquid Crystalline Copolyesters Prepared from Poly(ethylene terephtalate) (PET) and Rigid Aromatic Units

A series of copolyesters were synthesized by melt‐polycondensation reaction of poly(ethylene terephtalate) (PET) with various proportions of equimolar compositions of p‐acetoxybenzoic acid (p‐ABA), hydroquinone diacetate (HQDA) and terephtalic acid (TPA). Viscosity, liquid crystallinity, thermal properties, degree of crystallinity and thermal stabilitiy of these copolyesters were investigated by Ubbelohde viscometer, hot‐stage polarized light microscopy (PLM), differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and thermogravimetric analysis (TGA), respectively. On the basis of viscosity measurement, it was observed that intrinsic viscosity values of the copolyesters are increased regularly with increasing amounts of aromatic units (p‐ABA, HQDA and TPA) in the polymer chain. Thermotropic liquid crystalline behavior was observed in the copolyesters containing over 50 mol% of rigid p‐ABA/HQDA/TPA aromatic units. DSC analysis of the anisotropic copolyesters revealed broad and weak endotherms associated with the nematic phases, and the melting temperatures were found to be in the processable region. As the mol% of PET in the polymer chain increased, the specific enthalpies of fusion and the degree of crystallinity of the copolyesters were also increased regularly.     

Multi‐Stimuli‐Responsive Polymer Materials: Particles,Films, and Bulk Gels

Stimuli‐responsive polymers have received tremendous attention from scientists and engineers for several decades due to the wide applications of these smart materials in biotechnology and nanotechnology. Driven by the complex functions of living systems, multi‐stimuli‐responsive polymer materials have been designed and developed in recent years. Compared with conventional single‐ or dual‐stimuli‐based polymer materials, multi‐stimuli‐responsive polymer materials would be more intriguing since more functions and finer modulations can be achieved through more parameters. This critical review highlights the recent advances in this area and focuses on three types of multi‐stimuli‐responsive polymer materials, namely, multi‐stimuli‐responsive particles (micelles, micro/nanogels, vesicles, and hybrid particles), multi‐stimuli‐responsive films (polymer brushes, layer‐by‐layer polymer films, and porous membranes), and multi‐stimuli‐responsive bulk gels (hydrogels, organogels, and metallogels) from recent publications. Various stimuli, such as light, temperature, pH, reduction/oxidation, enzymes, ions, glucose, ultrasound, magnetic fields, mechanical stress, solvent, voltage, and electrochemistry, have been combined to switch the functions of polymers. The polymer design, preparation, and function of multi‐stimuli‐responsive particles, films, and bulk gels are comprehensively discussed here.